★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

What a Burnham Boiler Replacement Costs in Metro Vancouver

Boilers

What a Burnham Boiler Replacement Costs in Metro Vancouver
Home › What a Burnham Boiler Replacement Costs in Metro Vancouver

What a Burnham Boiler Replacement Costs in Metro Vancouver

Key takeaways

  • A ballpark installed range for a condensing gas boiler replacement in Greater Vancouver is $7,000 to $15,000 before GST, and a gas combi boiler that also makes domestic hot water generally lands in the $8,000 to $14,000 and up range. These are orientation figures, not a quote.
  • The boiler itself is often less than half the invoice. Venting, gas line capacity, near-boiler piping, condensate routing, electrical and removal of the old unit are where the number actually moves.
  • Switching from an older atmospheric boiler to a condensing one almost always means a new vent path and a condensate drain, which is the single biggest jump in price on older Metro Vancouver homes.
  • Size is set by a heat loss calculation, not by copying the rating plate on the boiler being removed. Oversizing is common in older houses that have since been insulated and re-windowed.
  • Permits and inspection are a separate line item set by your municipality or Technical Safety BC, and a compliant job includes them.
  • When two Burnham quotes differ by thousands, the gap is usually scope, not margin. Compare line by line before you compare totals.

A Burnham gas boiler replacement in Metro Vancouver typically falls in a ballpark installed range of $7,000 to $15,000 before GST for a condensing unit, and $8,000 to $14,000 and up if you are installing a combi boiler that handles both space heating and domestic hot water. Those are ballpark figures for orientation only, not a quote, and an accurate price needs a site visit: the boiler is a fixed catalogue item, but the work around it is written by your mechanical room, your venting route, your gas line and your existing distribution. Two houses on the same block can be $4,000 apart with the identical appliance sitting in the crate. This page explains what is inside a complete job, what site conditions add labour, which choices inside the Burnham line change the number, and how to read two quotes side by side so the cheaper one is not simply the one leaving work out. BC Wide is an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029. We install and service Burnham equipment; we are not a factory-authorised dealer, distributor or warranty centre for Burnham or any other brand.

What does a Burnham boiler replacement actually cost in Metro Vancouver?

For a residential gas boiler replacement in the Lower Mainland, a reasonable ballpark installed range is $7,000 to $15,000 before GST and before any rebate. Again, that is a ballpark for orientation, not a quote; the only number that means anything is the one written after a technician has seen the mechanical room, measured the vent route and checked the gas supply.

If you are replacing a heating-only boiler with a heating-only boiler, and the mechanical room is tidy, the vent can go out the same wall, and the gas line is already adequate, you will usually sit in the lower half of that range. If the house is on a mid-efficiency or atmospheric boiler venting into a masonry chimney, and you are moving to a condensing appliance, you are typically in the upper half or above it, because that is a different job wearing the same name.

A combi boiler, which makes your domestic hot water on demand as well as heating the house, is its own category. Ballpark, a gas combi boiler installation runs $8,000 to $14,000 and up, and the upper end is genuinely open because a combi changes your hot water infrastructure too: the water heater comes out, domestic piping gets rerouted to the boiler, and the gas demand at peak goes up.

Wide ranges are not evasion. A boiler replacement is a custom mechanical job in an existing building, and honest pricing reflects that until someone has actually looked.

What is included in a complete boiler replacement versus a bare swap?

The phrase that causes most of the confusion between two quotes is boiler replacement, because it describes two very different scopes. A bare swap removes the old appliance, sets the new one on the same footprint, reconnects to whatever piping, venting and wiring already exists, fires it and leaves. A complete replacement treats the appliance as one component in a system that has to be brought up to current code and commissioned properly.

When you read a quote, look for whether the following are present, priced, and described rather than implied.

  • Heat loss calculation to size the boiler, rather than matching the output of the unit being removed.
  • Removal, draining and legal disposal of the existing boiler, including any old expansion tank.
  • New near-boiler piping: isolation valves, unions, purge valves, air separator, expansion tank, pressure relief valve piped to a safe discharge point.
  • Circulator pump or pumps, sized and located correctly rather than reused because they still spin.
  • Complete venting: intake and exhaust, correct material, correct terminations, correct clearances from windows, doors and property lines.
  • Condensate handling on a condensing boiler, including neutraliser and a legal termination point, plus a condensate pump if there is no gravity fall.
  • Gas line verification and, where needed, upsizing from the meter.
  • Electrical connection, dedicated circuit where required, and low-voltage control wiring.
  • System flush or filter installation to protect the new heat exchanger from sludge and debris in old piping.
  • Permit application, inspection, commissioning readings, and a walkthrough on operating and maintaining the unit.

What site conditions add the most labour to the job?

Almost every dollar of difference between a straightforward replacement and an expensive one comes from the building, not the boiler. Venting is first. An older Metro Vancouver home with a boiler in the basement venting into a brick chimney has no vent path for a condensing appliance, so a new sealed intake and exhaust have to be routed to an exterior wall with correct clearances. A short, direct run through a rim joist is modest work. A long run through finished ceilings, around ducting, up a shaft, or to a wall that faces a narrow side yard with a window or a property line in the way is a real portion of the invoice.

Gas capacity is second. A condensing boiler, and especially a combi, can ask more of the supply at peak than what came before it. If the existing line is undersized for the new total connected load, a new or upsized run is required. Ballpark, a new gas line for an appliance runs $500 to $1,500 where the run is short and accessible, and $1,500 to $3,000 or more where it is long or difficult: through finished walls, along a crawlspace, or back to a meter that itself has to be reviewed.

Condensate is third and people forget it. A condensing boiler produces acidic condensate continuously in heating season, and it has to reach an approved drain with a neutraliser. If there is no drain near the boiler, you are adding a pump and a discharge line.

After that: access, electrical, and the state of the existing distribution. A boiler in a crawlspace or a cramped strata locker costs more to work in than one in an open basement. If the panel has no room for the circuit the new equipment needs, that is electrical work by a licensed electrician. And if the rads, loops and zone valves are original, some of them may need attention before a modulating boiler can behave as designed.

Site conditionWhy it adds cost
Old atmospheric boiler venting into a chimneyA condensing unit cannot use that chimney, so a complete new sealed intake and exhaust route has to be built and terminated to code.
Long or obstructed vent runMore material, more penetrations, more finished surfaces opened and repaired, sometimes a different termination strategy.
Undersized or distant gas lineNew or upsized piping from the meter, pressure testing, and reinspection of the total connected load.
No floor drain near the boilerCondensate pump, neutraliser and a discharge line routed to an approved termination.
Cramped crawlspace, locker or closetSlower work, restricted clearances, sometimes disassembly of the old unit to get it out at all.
Full electrical panelLicensed electrical work to provide the circuit the new controls and pumps require.
Original near-boiler piping and zone controlsRepiping and control replacement so the new boiler can modulate and circulate as designed.
Sludge in an old hydronic loopFlushing and filtration to protect a new heat exchanger from debris carried out of aging piping.

Which choices inside the Burnham line change the price?

Burnham is a long-established North American hydronic brand with a broad catalogue, and the spread inside that catalogue is wide enough to move your quote by thousands on its own. Rather than naming series here, it is more useful to understand the four choices that actually drive the number, and then confirm the specific model designation on the quote and on the rating plate of whatever is proposed.

First, condensing versus non-condensing. A condensing boiler extracts more heat from the flue gases and therefore vents cool and wet through sealed plastic or stainless venting, which is usually the better long-term choice but also brings the vent and condensate work described above. A non-condensing cast iron unit is simpler and often cheaper to install where a suitable existing vent can legally be reused, though that is less common than homeowners assume.

Second, cast iron versus stainless or aluminium heat exchanger. These are different materials with different maintenance expectations, different water-quality sensitivities and different price points. Ask what the manufacturer’s documentation says about water treatment and annual service for the exact model proposed, because that requirement follows the heat exchanger, not the brand.

Third, fixed-fire versus modulating. A modulating boiler with outdoor reset adjusts its output to the weather instead of cycling on and off at full fire, which suits our long mild shoulder seasons well. It costs more up front and is the choice most likely to pay you back in comfort on the coast.

Fourth, heating-only versus combi. A combi removes the tank water heater from the equation and is genuinely attractive in a space-limited townhouse or condo, but it has to be sized for simultaneous heating and hot water demand and it changes your domestic water piping.

Whatever is proposed, the model number, input rating and efficiency rating belong on the written quote and appear on the appliance rating plate. Verify them against Burnham’s own published documentation rather than against anything said verbally.

Which line items are quoted separately and should never carry a number here?

Some parts of a boiler project are real costs but are not ours to put a figure on, and you should be suspicious of any page that does. Permit fees are set by your municipality or by Technical Safety BC, and they vary across Metro Vancouver, so a contractor quotes them as a pass-through or tells you to expect them as a separate line. Rebates and incentive programs change their terms and eligibility on their own schedule, so treat any specific amount you read online as already out of date and confirm directly with the administering program before you count on it.

Likewise, a diagnostic or service call fee, financing terms, and annual maintenance are all separate conversations from the installed price of the equipment. They belong on the quote by name so you can see them, not buried in the total and not estimated on a web page.

Line items that should appear by name, without us attaching a figure: permit and inspection, any applicable rebate or incentive, financing if you use it, a service call or diagnostic if one preceded the quote, and an annual maintenance plan if you take one.

Things that legitimately carry a number on your quote: the appliance, the labour, venting materials, gas piping, near-boiler piping and components, electrical, condensate handling, disposal, and any drywall or finishing repair.

Why does Metro Vancouver change the boiler math?

Our climate is mild and wet, and the heating season is long rather than severe. That favours a modulating condensing boiler with outdoor reset, because the appliance spends most of the year running gently at partial load instead of short-cycling at full fire. It also means a boiler sized to a genuine heat loss calculation rather than a worst-case guess will be noticeably smaller than the unit it replaces in a house that has been insulated or re-windowed since the 1970s.

Our water is soft. That matters because the hydronic failure mode here is not limescale, it is sludge and corrosion: magnetite and debris accumulating in old steel and cast iron piping, then getting pulled into a new heat exchanger the moment a fresh circulator starts moving water that had settled for decades. Flushing the system and fitting filtration is not an upsell in this market, it is protection for the most expensive component in the job.

The housing stock is the other local factor. East Vancouver, Burnaby and New Westminster have plenty of pre-1980 homes with cast iron boilers, original near-boiler piping and chimney venting, and those are the jobs that land at the upper end of the range. Strata townhouses and condos bring their own constraints: shared walls limit where a vent can terminate, bylaws govern exterior penetrations, and strata approval is a scheduling reality that has to be started early. If you are in a strata, get the approval process moving before you book the work.

Finally, coastal air is corrosive near the water and termination locations need thought, and BC gas work and most electrical work are legally restricted to licensed trades. A boiler replacement in this province is a permitted, inspected job, and a quote that skips the permit is not saving you money, it is transferring risk to you at resale and at insurance time.

How do you compare two Burnham quotes side by side?

When two quotes for the same brand are thousands apart, the difference is nearly always scope. Put them next to each other and compare the work described, not the totals. If one quote is a paragraph and the other is two pages, you are not looking at the same job.

Ask each contractor the same set of questions and write the answers down. What model number, and what input rating, and how was the size determined? Is a heat loss calculation included, and may I see it? What venting material and route, and where exactly does it terminate? Is the gas line being verified or upsized, and is that in the price or an allowance? How is condensate being handled? Is the old boiler’s removal and disposal included? Is the permit in the price or extra? Is a system flush and filtration included? Is drywall repair after vent penetrations included, and to what standard? Who does the electrical work?

Watch for allowances and exclusions. An allowance is a placeholder that can grow after work begins. Exclusions are where the cheaper quote usually hides: gas line upgrades excluded, permit excluded, electrical by others, patching by others, disposal by others. Add those back in and the two numbers often converge.

Also confirm warranty administration in writing. Manufacturer warranty terms come from Burnham’s own documentation and registration requirements, and labour warranty comes from the contractor. Ask who you call, and what each one covers, and get it on the quote instead of on a phone call.

  • Same model number on both quotes, or the difference explained.
  • Heat loss calculation included and available to read.
  • Venting scope, material and termination described, not implied.
  • Gas line stated as verified, upsized, or excluded.
  • Condensate route and neutraliser named.
  • Permit, inspection and disposal explicitly in or out.
  • System flush and filtration addressed.
  • Warranty split between manufacturer and contractor labour, in writing.

When should you call a licensed technician?

Everything structural about a boiler replacement is licensed work in British Columbia. Gas connections, venting, combustion testing and commissioning must be done by a licensed gas fitter, and the associated electrical work by a licensed electrician. There is no homeowner path through that, and an unpermitted installation can create problems with insurance and at the time of sale.

What a homeowner can reasonably do: read the rating plate and photograph it, note the existing vent type and where it terminates, find the gas meter and the electrical panel, clear access to the mechanical room before the crew arrives, check the boiler pressure gauge and note it, and keep records of past service. Those five minutes make every quote you receive more accurate.

Call a licensed technician immediately, rather than waiting for quote season, if you smell gas, if a carbon monoxide alarm sounds, if you see soot or scorching around the boiler or vent, if the boiler is leaking water onto the floor, if the relief valve is discharging, or if the unit is locking out repeatedly. Same-day attendance is often possible in Metro Vancouver depending on the day and the call volume, and we will tell you honestly when it is not rather than promise an arrival window we cannot hold. For a gas smell, leave the building first and call from outside.

For a planned replacement, book the assessment outside the first cold snap. Every boiler in the Lower Mainland reveals its condition in the same two weeks, and that is the worst time to be making a fifteen-thousand-dollar decision under pressure. To arrange an assessment, call BC Wide at (604) 473-9690.

Gas & carbon-monoxide safety: A gas boiler is combustion equipment. Never operate a boiler with a damaged, disconnected or improperly terminated vent, and never block combustion air openings in the mechanical room. Install working carbon monoxide alarms on every level of the home, particularly near sleeping areas, and test them monthly. If you smell gas, hear hissing, or a carbon monoxide alarm sounds, leave the building immediately, do not use switches or phones inside, and call from outside; contact FortisBC’s emergency line or 911 first, then a licensed contractor. Soot, scorching, a persistent flue-gas smell, water pooling under the boiler or a discharging relief valve all mean the appliance should be shut off and inspected. Gas work, venting and most electrical work are legally restricted to licensed trades in British Columbia, and boiler replacements require a permit and inspection.

Frequently asked questions

Why is there such a wide range in the price of a Burnham boiler replacement?

Because the appliance is often less than half the invoice and the rest is written by your building. Venting route, gas line capacity, condensate routing, electrical, access and the condition of the existing distribution all vary house by house. A ballpark range of $7,000 to $15,000 reflects that honestly; a single number before a site visit would not.

Is a combi boiler cheaper than a boiler plus a separate water heater?

Not usually, at least not on the day of installation. A gas combi boiler installation sits in a ballpark range of $8,000 to $14,000 and up, and it also involves rerouting domestic hot water piping and removing the existing tank. Its real advantage is recovered floor space and one appliance to service, which matters most in a townhouse or condo.

Can I keep my existing chimney if I install a condensing Burnham boiler?

Almost never. A condensing boiler vents cool, wet flue gases that a masonry chimney is not designed to handle, so it needs a sealed intake and exhaust routed to an approved exterior termination. That new vent path is the single most common reason an older Metro Vancouver home’s quote lands higher than the homeowner expected.

Should the new boiler be the same size as the one I am removing?

No. Size should come from a heat loss calculation on your house as it is today. Many older Lower Mainland homes have been insulated, air-sealed or re-windowed since the original boiler was installed, so the correct new output is often smaller. Oversizing costs more up front and causes short cycling and uneven comfort afterward.

Does the quote include the permit?

It should be stated one way or the other. Permit and inspection fees are set by your municipality or Technical Safety BC, so a contractor passes them through rather than absorbing them into a headline price. Ask whether the permit is included or billed separately, and never accept a boiler replacement done without one.

Why does one Burnham quote come in thousands below another?

Nine times out of ten it is scope, not margin. Compare the exclusions: gas line upgrade, permit, electrical, disposal, system flush, drywall repair and condensate handling are the items commonly left out of a lower number. Add the missing work back in and the totals usually move much closer together.

How long does a boiler replacement take?

A straightforward like-for-like replacement in an accessible mechanical room is commonly a one-day job. A conversion from an atmospheric boiler to a condensing unit, with new venting, gas line work and condensate routing, more often runs two to three days. Strata approvals and inspection scheduling can extend the calendar even when the labour itself is short.

Is BC Wide a Burnham dealer?

No. BC Wide is an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029, serving Metro Vancouver since 1999. We install and service Burnham equipment along with other major brands, but we are not a factory-authorised dealer, distributor or warranty centre for Burnham. Manufacturer warranty terms come from Burnham’s own documentation.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote