- The most common reasons a Carrier Comfort Series furnace stops heating are a thermostat or power issue, a clogged filter tripping the high-limit safety, or an ignition fault such as a dirty flame sensor or worn hot-surface igniter.
- On condensing versions of this family, a blocked condensate drain or a plugged plastic vent is a frequent cause, because the pressure switch cannot prove the vent and the furnace will not light.
- Owners may safely check the thermostat mode and batteries, the furnace service switch, the breaker and the filter. Everything behind the front panel is licensed gas work in BC.
- Note the flashing pattern of the status light before you touch the power, and pass it to the technician rather than trying to interpret it yourself.
- A gas smell, a sounding carbon monoxide alarm, scorch marks or water pooling around the furnace means stop, get out if needed, and call for licensed help.
- Whether to repair or replace depends on the age of the furnace, the condition of the heat exchanger, part availability and repeat failures. Ask for a written quote before any work.
When a Carrier Comfort Series furnace stops heating the house, the most likely cause is something simple upstream of the furnace: a thermostat set to the wrong mode or running on dead batteries, a tripped breaker or service switch, or a filter so clogged that the furnace has overheated and shut its burners off on the high-limit safety. The next most likely causes sit on the ignition side, a dirty flame sensor or a worn hot-surface igniter, and on the condensing versions of this family, a blocked condensate drain or a plugged plastic vent pipe that stops the furnace from proving its venting. An owner can safely check the thermostat, the service switch, the breaker and the filter. Anything past the front panel, including the burners, gas valve, igniter, sensors and control board, is licensed gas work in British Columbia. If those checks do not bring the heat back, call BC Wide Home Services at (604) 473-9690. We are an independent TSBC-licensed contractor (LGA0090068, CGA0028029) serving Metro Vancouver since 1999, and we service and install the Carrier Comfort Series as an independent contractor, not as a factory-authorised dealer or warranty centre.
Why is my Carrier Comfort Series furnace not heating the house?
Almost every no-heat call on this family falls into one of three groups: the furnace is never asked to run, it is asked but a safety stops it from lighting, or it lights and then shuts down before the house warms up. Working out which group you are in narrows the cause quickly, and most of that sorting can be done by listening and watching without opening anything.
If nothing happens at all when the thermostat calls, no inducer hum and no blower, the problem is usually power or the thermostat. If you hear the small inducer fan start, then nothing, and the cycle repeats, the furnace is usually failing to prove the vent or failing to light. If the burners light for a few seconds and go out, the flame sensor is the classic suspect. If the blower runs for a long time and the air coming out of the registers feels cool, the burners are either not lighting or have been shut off by a safety while the blower keeps running to cool the heat exchanger.
| What you notice | Most likely cause | Who handles it |
|---|---|---|
| Thermostat screen blank or not calling for heat | Dead batteries, wrong mode, setpoint below room temperature, wiring or power fault | Owner checks batteries and mode; wiring is a technician job |
| Furnace completely silent | Service switch off, tripped breaker, blown low-voltage fuse on the control board, door safety switch not closed | Owner checks switch, breaker and door; board and fuse are technician work |
| Inducer runs, then stops, repeats, no flame | Pressure switch not proving: blocked vent, blocked condensate trap or drain, cracked hose, weak inducer | Technician |
| Burners light briefly then go out | Dirty or poorly grounded flame sensor, weak flame, gas pressure issue | Technician |
| Glow but no flame, or no glow at all | Worn or cracked hot-surface igniter, gas valve not opening | Technician |
| Blower runs, air is cool, burners off | High-limit trip from a clogged filter or closed registers, or a lockout after repeated failed ignitions | Owner replaces filter and opens registers; repeat trips need a technician |
| Water around the base of the furnace | Condensate trap, hose or drain blocked or leaking on a condensing version | Technician; turn the furnace off at the service switch |
What can I safely check on a Carrier Comfort Series furnace before calling?
These checks are safe for any homeowner and solve a real share of no-heat calls. Stop at the front panel. Do not remove the burner compartment door, do not try to light anything by hand, and do not jumper or bypass any switch.
- Thermostat: confirm it is set to Heat, not Cool, Off or Auto fan only, and that the setpoint is a few degrees above the current room temperature. Replace the batteries if the screen is faint or blank. If the thermostat also controls a heat pump in a dual-fuel setup, check that it has not been left on a cooling or fan-only schedule from summer.
- Service switch: most furnaces have a switch that looks like a household light switch mounted on or near the cabinet. It gets flipped off by accident more often than you would think, especially in basements and storage closets.
- Breaker: check the panel for a tripped furnace breaker. Reset it once. If it trips again, leave it off and call, because a breaker that keeps tripping points to an electrical fault.
- Filter: slide the filter out and hold it up to a light. If you cannot see light through it, replace it with the same size printed on the frame. A choked filter is one of the most common reasons a furnace shuts its burners off on the high-limit safety.
- Registers and returns: make sure supply registers are open and that furniture, rugs or storage boxes are not blocking the return grilles.
- Status light: many furnaces in this family have a small window in the lower door where a light on the control board flashes a pattern. Write down or video the pattern before you cut power. Match it only against the key printed on the door, and pass it on to the technician rather than acting on it.
- Power cycle once: after the checks above, you may turn the service switch off for a minute and back on to clear a lockout one time. If the furnace goes back into the same failure, stop. Resetting a lockout over and over can load the heat exchanger with unburned gas and hides the real fault.
How is the Carrier Comfort Series usually installed in Lower Mainland homes?
The Comfort Series is Carrier’s value-positioned residential gas furnace family, and it appears in both non-condensing and condensing versions. Which one you have changes the likely causes of a no-heat problem, so it is worth knowing. A non-condensing version typically vents into a metal flue or a lined chimney and has no condensate drain. A condensing version typically vents through plastic pipe out a side wall or the roof, has a second combustion-air pipe on sealed-combustion installations, and carries a condensate trap and drain line. The exact configuration, input rating and efficiency for your unit are manufacturer-published; check the rating plate inside the cabinet door and the installation manual for your exact unit.
In Metro Vancouver we most often find this family in a few settings. In detached homes from the 1960s through the 1990s it is often an upflow furnace in a basement or utility room, sometimes replacing an older unit that vented into a masonry chimney. In townhouses it is often in a closet, a garage or a crawlspace, sometimes in a horizontal position with the vent run through a side wall a short distance from a neighbour’s window or a walkway. In newer homes it may be paired with an outdoor heat pump or central air conditioner coil sitting on top of the furnace.
Those settings matter. A horizontal furnace in a crawlspace or attic has its condensate trap in a different orientation and is more exposed to cold air and debris. A closet install with limited return air is more likely to trip the high limit. A furnace paired with a heat pump coil in a dual-fuel system has a second set of controls, so the thermostat may be deciding which one runs.
Why does my furnace start, then shut off or blow cold air?
Understanding the normal start-up sequence explains most of these symptoms. When the thermostat calls for heat, the control board first checks that its safety switches are in their normal state. It then starts the inducer motor to pull air through the heat exchanger and out the vent. A pressure switch has to sense that draft before the board will continue; if the vent, intake or condensate path is blocked, the switch never closes and the furnace stops at this step.
Once the draft is proven, the hot-surface igniter heats up until it glows, the gas valve opens, and the burners light. The flame sensor, a small metal rod sitting in the flame, has to confirm the flame within a few seconds. If it cannot, because it is coated in oxide film, the flame is weak, or the furnace has a grounding problem, the board closes the gas valve. After several failed tries the board goes into a timed lockout.
When the burners stay lit, the blower starts after a short delay to move warm air through the ducts. If the heat exchanger overheats because airflow is restricted, the high-limit switch opens, the burners shut off and the blower keeps running to cool things down. From the living room, that feels like the furnace running but blowing cool air. The fix for that symptom is usually the filter or the ductwork, not the burners.
What do technicians usually find on this kind of furnace?
On Comfort Series service calls across the Lower Mainland, the findings tend to follow a pattern. The first is a contaminated flame sensor, which is cleaned or replaced and is one of the quicker repairs we make. The second is a worn or cracked hot-surface igniter; these are consumable parts that weaken with age and often fail on the first cold morning of the season. The third, on condensing versions, is the condensate path: a trap full of sludge, a kinked or sagging drain hose, or a condensate pump that has failed, any of which can hold water where the pressure switch needs air.
Less often we find a failing inducer motor that is too weak to close the pressure switch, a pressure switch hose that has cracked or come loose, a high-limit switch that has weakened after years of tripping on a choked filter, loose low-voltage wiring, or a control board fault. A control board is one of the more expensive parts on a gas furnace, so we confirm the board is actually at fault by testing inputs and outputs before recommending one.
Every licensed visit should also include the checks that do not show up as a symptom: gas pressure, combustion quality, venting condition and a look at the heat exchanger. A furnace that suddenly started tripping its high limit after years of normal service deserves a careful heat exchanger inspection, not only a new filter.
What makes Metro Vancouver furnaces different?
Our mild, wet coastal climate means furnaces here run long, gentle cycles for much of the year rather than hard cycles through deep cold. That is easy on the equipment, but it also means many owners do not notice a weak igniter or dirty sensor until the first proper cold snap, when the phones light up across the region at once.
Rain, leaves and moss are the local enemies of side-wall venting. On condensing versions, we regularly find intake and exhaust terminations partly blocked by leaf litter, fern growth, spider webs, landscaping or a wasps’ nest, and in a rare hard frost, ice at the termination. Owners can look at the vent from outside and clear loose leaves by hand, but should not take apart or modify the pipe.
Older housing stock brings its own problems. Houses from the middle of the last century often have undersized return air ducts or returns that were closed off during renovations, which drives high-limit trips. Homes that converted from an older furnace to a condensing unit sometimes left an orphaned water heater on an oversized masonry chimney, which is a venting question for a licensed technician. In strata townhouses and condos, venting routes and furnace locations are constrained; owners should check their bylaws and any strata approval requirements with their council before planning replacement work, and questions about heritage properties go to the municipality.
Many Lower Mainland homes now pair a gas furnace with a heat pump in a dual-fuel system, where the heat pump carries mild weather and the furnace takes over on cold nights. If your Comfort Series furnace is part of that setup and the house is not warming, the problem may be in the changeover controls or the thermostat configuration rather than in the furnace itself.
When does it become a same-day licensed call?
Once the owner-safe checks are done and the house is still cold, the next step is a licensed gas technician. Some situations should not wait at all. We try to reach no-heat calls the same day where we can, especially for households with infants, older adults or anyone medically vulnerable, but we cannot guarantee an arrival window during a region-wide cold snap. We will tell you honestly when we can come.
- Any smell of gas: leave the house, do not operate switches or phones inside, and call from outside or a neighbour’s home.
- A carbon monoxide alarm sounding, or anyone feeling headache, nausea or drowsiness that eases when they go outside.
- Scorch marks, melted wiring, a burning smell that persists beyond the first dusty start-up of the season, or flames visible outside the burner area.
- Water pooling under or around the furnace.
- A breaker that trips again after one reset.
- The furnace going back into the same failure after one power cycle.
- A loud bang on ignition, which can mean delayed ignition and gas building up before it lights.
Should I repair or replace my Carrier Comfort Series furnace?
Most no-heat problems on this family are repairs, not replacements. A flame sensor, igniter, pressure switch or condensate fix returns a sound furnace to service. The picture changes when several things line up: the furnace is well into the later part of its expected service life, the heat exchanger shows cracks or heavy corrosion, parts are hard to source, or the same furnace has needed several repairs in recent seasons.
A cracked heat exchanger is a safety issue, not only an efficiency one, and it usually tips the decision towards replacement. Other factors worth weighing are whether the existing venting and gas piping suit a modern condensing furnace, whether the ductwork is actually the reason the furnace keeps overheating, and whether you want to pair the new furnace with a heat pump as a dual-fuel system so the gas furnace covers the cold nights.
We do not decide that on the phone. After a licensed inspection we give you a written quote that separates the repair option from any replacement option, explains why, and lets you choose. No work starts until you have approved it in writing.
Frequently asked questions
Why is my Carrier Comfort Series furnace running but blowing cold air?
Usually the burners have shut off while the blower keeps running. The most common reason is a high-limit trip from a clogged filter or blocked returns, followed by ignition failure and a lockout. Replace the filter, open the registers and power cycle once; if the air is still cool, call a licensed technician.
Can I reset my Carrier furnace myself?
You can turn the service switch off for a minute and back on once to clear a lockout. If the furnace goes back into the same failure, stop and call. Repeated resets hide the real fault and can let unburned gas build up in the heat exchanger.
What does the flashing light on my Carrier Comfort Series furnace mean?
It is a diagnostic pattern from the control board, and the key for your exact unit is printed on the furnace door. We do not interpret patterns on this page because they vary by version. Record the pattern before cutting power and give it to your technician, who will confirm the actual fault by testing.
Is a dirty flame sensor a common problem on this furnace?
Yes, it is one of the most frequent causes of a furnace that lights briefly and then shuts off. Cleaning or replacing the sensor is quick, but it sits inside the burner area, so in BC it is a job for a licensed gas technician rather than the homeowner.
My condensing Carrier furnace is leaking water and not heating. What should I do?
Turn the furnace off at the service switch and call a licensed technician. Water usually means the condensate trap, hose or drain is blocked or leaking, which can also stop the pressure switch from proving and prevent the furnace from lighting. Wipe up the water and keep it away from electrical components.
Is BC Wide a Carrier dealer or warranty centre?
No. BC Wide Home Services is an independent TSBC-licensed contractor that services and installs the Carrier Comfort Series along with other furnace brands. For warranty questions, check your paperwork and contact the manufacturer; we can document what we find on a service visit so you have it on record.
Can you come today if my furnace is not heating?
Same-day where we can. During a cold snap, demand across Metro Vancouver spikes and we cannot promise a set arrival window, but we prioritise homes with no heat and vulnerable occupants. Call (604) 473-9690 and we will tell you honestly when a licensed technician can be there.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
How often should a furnace be serviced?
How long does a furnace last in Vancouver's climate?
Why is my furnace blowing cold air?
How much does a new furnace cost in Vancouver?
What is the most reliable furnace brand?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


