★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Comparing This Winter to Last Winter Fairly

Furnace

Comparing This Winter to Last Winter Fairly
Home › Comparing This Winter to Last Winter Fairly

Comparing This Winter to Last Winter Fairly

Key takeaways

  • Two heating bills are only comparable after you correct for two things: how many days the billing period covered, and how cold those days actually were.
  • The weather correction is called heating degree days, and it is published for local weather stations, so you never have to guess whether the winter was colder.
  • Read your own meter on a fixed day each month. An estimated bill followed by a true-up read can look like a sudden spike when nothing changed at all.
  • Gas use for a house is billed in energy units printed on the bill itself, and the furnace rating plate in the mechanical room tells you what the appliance is rated to draw.
  • A genuine jump with no weather, no schedule and no occupancy change behind it can point at combustion, airflow or control problems, and those are worth investigating rather than absorbing.
  • Carbon monoxide alarms belong on every level of the home, and a gas smell means leave the building first and call from outside.

A fair comparison between this winter and last winter starts by correcting for two things before you look at anything else: how many days each billing period covered, and how cold the outdoor air was during each of those periods. Once you have divided each period’s energy use by its number of days, and then compared that daily figure against the heating degree days for the same stretch of weather, most alarming winter bills quietly explain themselves. What is left after that correction is the part worth investigating, and it is usually one of four things: the weather, the building, the habits inside it, or the equipment. This page walks a Metro Vancouver homeowner through separating those four in order, using only the bill, a meter and a weather record, and then marks the exact point where free checks end and a licensed technician’s instruments begin.

Why does putting two bills side by side almost always mislead?

Because the two bills are not measuring the same thing. Utility billing periods drift. One period may run several days longer than the one you are comparing it against, and in the middle of a Metro Vancouver winter each extra day carries real heating load with it. A period that happens to catch a cold snap at both ends looks dramatically worse than one that caught mild rain, even with identical equipment, identical habits and an identical house.

There is a second and less obvious problem. Some bills are estimated rather than read. When the utility estimates a period low and then takes an actual reading the following period, the correction lands entirely in the later bill. Nothing changed in the house. The bill still doubles. Homeowners in that position often spend a season chasing an equipment fault that never existed.

The third distortion is memory. Last winter’s bill sits in an inbox with no emotional weight attached to it. This winter’s arrived after a cold week when the furnace ran hard and everyone noticed. The two are being judged by different standards before the numbers are even read.

  • Different period lengths: always divide energy used by days in the period before comparing anything.
  • Estimated versus actual reads: check whether each bill says estimated or actual, and treat an estimate-then-true-up pair as one combined period.
  • Rate and rider changes: your total owing can move without your consumption moving at all, which is why the comparison must be made in energy units, not in what you paid.
  • Seasonal timing: a billing period that straddles the coldest fortnight of the year is not comparable to one that straddles a thaw.

What are heating degree days, and where do I find them?

Heating degree days are the standard way of expressing how much heating weather a period contained. For each day, the average outdoor temperature is compared to a fixed indoor reference temperature, and the shortfall is recorded. A day that averaged well below the reference contributes a lot. A mild wet day contributes very little. Add up every day in the billing period and you have a single figure describing how hard that period asked your heating system to work.

Environment and Climate Change Canada publishes daily climate data for stations across the region, and degree-day totals can be pulled or calculated from the daily mean temperatures for the station nearest you. In Metro Vancouver the station matters more than people expect. A home in Burnaby, one in Coquitlam and one further up a valley can see meaningfully different totals over the same fortnight, and elevation adds to that.

Once you have degree days for both periods, the comparison becomes simple in shape: energy used per day, set against degree days per day. If both moved together in the same direction and roughly in proportion, the weather explains the bill and the investigation is over. If your energy use per day climbed while the degree days held steady or fell, something other than weather is driving it, and the rest of this page is about finding out what.

How do I do the comparison properly, step by step?

Work in order and do not skip ahead. Each step rules something out, and ruling things out in the wrong order is how people end up replacing equipment that was working correctly.

  • Pull both bills and write down, for each: the start date, the end date, the number of days, whether the read was estimated or actual, and the quantity of energy consumed in the unit the bill uses.
  • Divide energy consumed by days in the period. You now have a daily rate for each winter. Compare those, never the totals.
  • Look up the daily mean temperatures for the nearest weather station over both periods and total the heating degree days for each.
  • Divide degree days by days in the period, so you have degree days per day for each winter too.
  • Compare the two ratios. Energy per day against degree days per day is the honest comparison, and it is the only one that survives a change in billing period length.
  • Note anything that changed in the household: more people home during the day, a new baby in the house, a basement suite occupied, a renovation that opened up a space, a room that used to be closed off and now is not.
  • Note anything that changed in the settings: a thermostat schedule that was deleted, a hold that was left on, a setback that someone stopped using, a fireplace used more or less than before.
  • Only after all of that, start looking at the equipment.

What actually drives a gas heating bill?

It helps to know what you are looking at. A gas bill for a house is a record of energy delivered through the meter, expressed in the energy unit printed on the bill. That energy is shared between everything gas-fired in the home, and in a typical Metro Vancouver house the furnace or boiler is the largest share by a wide margin during winter, with the water heater second and a gas fireplace behind it. The table below sorts the usual drivers by how much they can move a winter bill and by whether you can check them yourself.

DriverHow it shows up on the billCan you check it yourself?
Outdoor temperature over the periodEnergy per day rises and falls with heating degree daysYes, using published daily climate data
Billing period lengthTotal rises with no change in daily rateYes, both dates are on the bill
Estimated read followed by a true-upOne low bill then one unusually high oneYes, the bill states estimated or actual
Thermostat setpoint and scheduleSteady lift in daily rate that persists across periodsYes, review the schedule and any hold
Occupancy and habitsDaily rate climbs on a pattern that matches the changeYes, think back over who was home and when
Building envelope: attic insulation, weatherstripping, an open crawlspace hatchDaily rate higher than a comparable past winter at similar degree daysPartly, visual inspection only
Ductwork leakage or a badly restricted filterLonger run times, uneven rooms, higher daily rateFilter yes, duct testing no
Combustion set-up, gas pressure, heat exchanger conditionUnexplained rise, possible soot, odours or repeated shutdownsNo, licensed technician only
Water heater: a failing dip tube, a recirculation loop left running, a leak on a hot lineDaily rate stays elevated even in mild weatherPartly, look for leaks and check timers
Gas fireplace with a standing pilot left on all seasonA small steady load that never goes awayYes, check whether the pilot is lit in summer

How do I read my own meter and build a baseline?

Reading your own meter is the single most useful habit for anyone who wants to argue with a bill and be right. Pick a day of the month, put a recurring reminder on your phone, and photograph the meter dials or digital display on that day every month. Write the reading and the date in the same note each time. Within a few months you own a record that is independent of the utility’s billing calendar and immune to estimated reads.

The gas meter is outdoors on an exterior wall or in a meter enclosure, and reading it requires nothing but your eyes. Do not open anything, do not turn anything, and do not touch the piping, valves or regulator. If a dial appears stuck, if you hear hissing, or if you smell gas near the meter, that is not a reading problem and you should treat it as the safety issue described further down this page.

A baseline also lets you separate heating load from everything else. Take a reading at the end of a genuinely mild stretch when the furnace has barely run. Whatever the meter moved during that window is roughly your non-heating gas use: hot water, cooking, the fireplace if it is lit. Subtract that from a winter period and what remains is heating. That single subtraction turns a vague suspicion into a measurement you can act on.

What does a Metro Vancouver winter do to this comparison?

Our climate makes fair comparison harder than it is in a colder, drier part of the country. Metro Vancouver winters are mild, wet and variable. A season here can swing from a long grey stretch barely below the heating reference temperature to an outflow event that drops temperatures sharply for a week. Two consecutive winters can differ far more than people remember, which is exactly why degree days beat memory.

Humidity plays its own part. Damp coastal air makes a house feel colder at the same thermostat setting, so households nudge the setpoint up in winter without registering that they have done it. A small permanent lift in setpoint applied across a whole heating season shows up clearly in energy per day and explains a great many mystery bills.

Our housing stock matters too. Large parts of Burnaby, New Westminster, East Vancouver and the North Shore are full of homes built long before current insulation and air-sealing standards, often with ducts running through unconditioned crawlspaces and attics. A furnace that is working perfectly still has to fight a leaky envelope, and envelope performance degrades over decades. Suite conversions are common here as well, and a basement suite that became occupied between two winters is a real and complete explanation for a higher bill.

Strata and townhouse owners face a different version of the problem. Shared walls, shared corridors and neighbours who moved out or moved in all change how much heat your unit loses. If the unit beside yours sat empty and unheated through one winter and was occupied through the next, your own bill moved without anything in your home changing.

Finally, our water is soft. That means hydronic systems here suffer from sludge and corrosion rather than limescale, and a boiler losing efficiency to circulation problems in a sludged system is a genuine cause of a rising bill that no amount of thermostat discipline will fix.

When does a higher bill mean a furnace problem?

Suspect the equipment when the normalised comparison refuses to close. That is, when energy per day rose, degree days per day did not, nothing changed about the household, the schedule or the envelope, and the increase has persisted across more than one billing period. A single odd period is usually a billing artefact. A sustained rise against flat degree days is a signal.

Equipment causes divide roughly into three families. Combustion problems mean the appliance is not converting fuel into useful heat as completely as it should, often visible as soot, odd flame colour or a burner that will not stay lit. Airflow problems mean the heat is produced but not delivered, so the furnace runs longer for the same result, which is what a crushed duct, a badly leaking duct run or a neglected filter does. Control problems mean the appliance runs when it should not, which is what a failing limit switch, a miswired thermostat or a short-cycling sequence looks like on a bill.

There is one more, and it deserves to be said plainly rather than buried. A gas appliance that suddenly consumes more fuel with no explanation can be a combustion problem, and combustion problems are the family that can also produce carbon monoxide. Rising fuel use is not proof of danger, but it is a reason to have the appliance inspected rather than to shrug and pay.

  • Run times feel longer than you remember for the same outdoor conditions.
  • Rooms that used to reach setpoint now lag, particularly rooms at the end of a duct run.
  • The furnace starts and stops in short bursts rather than settling into longer cycles.
  • Soot marks, a sharp smell, or a burner flame that looks yellow and lazy rather than crisp and blue.
  • The appliance locks out and needs resetting, even occasionally.
  • A carbon monoxide alarm has sounded at any point, even once, even briefly.

Where do the free checks end and a technician’s measurements begin?

Everything in the comparison itself is yours to do. Reading bills, counting days, looking up degree days, reading the meter, reviewing the thermostat schedule, changing a filter to the size and type listed on the existing one, checking that supply and return registers are not blocked by furniture or rugs, closing a crawlspace hatch that was left open, and noticing that a fireplace pilot has been burning since spring. None of that requires a licence and all of it is genuinely useful.

The measurements that actually diagnose equipment do require one. Gas work and most electrical work is restricted to licensed trades in British Columbia, and for good reason. Manifold and inlet gas pressure, combustion analysis of the flue gas, temperature rise across the heat exchanger, static pressure across the air handler, airflow verification, and any inspection of the heat exchanger itself are technician work. So is anything touching refrigerant on a heat pump or air conditioner, which by law only a certified technician may handle, recover or charge.

A useful way to think about the boundary: you can gather evidence, and you can remove obvious obstacles. You cannot open a sealed combustion path, you cannot alter gas piping, and you cannot judge a heat exchanger by looking at the outside of a furnace. When the evidence you gathered points at the equipment, hand the evidence over rather than trying to complete the diagnosis yourself.

TaskHomeownerLicensed technician
Recording meter readings and billing datesYesNot required
Collecting degree days and normalising the comparisonYesNot required
Replacing the air filter with the same size and typeYesNot required
Clearing blocked supply and return registersYesNot required
Reviewing and correcting the thermostat scheduleYesNot required
Checking whether a fireplace pilot is burning year-roundYes, visual onlyFor adjustment or shutdown, yes
Combustion analysis and flue gas measurementNoYes
Gas pressure measurement or any gas piping workNoYes
Heat exchanger inspectionNoYes
Static pressure and airflow measurement, duct testingNoYes
Any refrigerant handling on a heat pump or air conditionerNo, legally restrictedYes, certified technician
Electrical work inside the appliance or at the disconnectNoYes

What should I do next with what I found?

If the comparison closed and the weather explained the bill, do nothing to the equipment and put the effort into the envelope and the schedule instead. Attic insulation, weatherstripping, sealing the obvious gaps around a crawlspace hatch and using a setback schedule properly are the levers that reduce the load rather than chase the symptom. Write your degree-day-normalised figure down so next winter you have a real baseline to compare against instead of a feeling.

If the comparison did not close, book a diagnostic visit and bring your evidence. Give the technician both billing periods with dates and consumption, your degree-day figures, your own meter readings if you have them, the age and location of the appliance, and the symptoms you noticed. That turns an open-ended hunt into a targeted one and means the visit is spent measuring rather than interviewing.

Ask for the findings in writing, and ask for any recommended repair to be quoted in writing before work proceeds. A written quote lets you compare scope rather than promises, and it gives you something to hold on to if the same symptom returns. If a repair is recommended on a furnace that is well past its service life, ask the technician to lay out the condition of the heat exchanger and the realistic remaining life alongside the repair, so you are choosing between two clear options rather than reacting.

One last note on heat pumps, because it comes up whenever bills are on the table. In our climate the sensible path is a dual-fuel setup: a heat pump doing the work through our long mild shoulder seasons with the gas furnace retained as backup for cold snaps. That arrangement changes the shape of your bill rather than simply shrinking one line of it, since load shifts between two meters, and it means that after an installation your old winter-to-winter comparison no longer applies at all. Start a fresh baseline from the first full period after the changeover.

BC Wide Home Services Ltd has been working on gas heating in Metro Vancouver since 1999. We are an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029, and we service equipment from many manufacturers rather than representing any one of them. If your bill went up and the weather does not explain it, call (604) 473-9690 and we will come and measure it. Same-day attendance is sometimes possible depending on the day and the route, and we will tell you honestly when it is not rather than give you a window we cannot keep.

Gas & carbon-monoxide safety: Gas and carbon monoxide safety comes before any billing question. Install carbon monoxide alarms on every level of the home, including outside sleeping areas, and test them on a schedule. If an alarm sounds, get everyone outside into fresh air and call from outside. If you smell gas anywhere, including near the meter, do not operate light switches, appliances or garage doors, do not look for the source, leave the building immediately and call your gas utility’s emergency line from outside. Carbon monoxide is colourless and odourless, and symptoms such as headache, nausea, dizziness or drowsiness that improve when you leave the house should be treated as an emergency, not as a cold coming on. Soot marks around a furnace, water heater or fireplace, a yellow lazy burner flame, or an appliance that repeatedly locks out all call for a licensed technician rather than a reset. Gas work and most electrical work is legally restricted to licensed trades in British Columbia, and refrigerant may only be handled by a certified technician. A heating bill that climbs with no weather, schedule or occupancy change behind it can indicate a combustion problem, which is a safety matter as well as a cost one, and is worth an inspection.

Frequently asked questions

Can I just compare this month’s bill to the same month last year?

Not directly, because the two billing periods almost certainly covered a different number of days and a different amount of cold weather. Divide each period’s energy use by its number of days first, then compare those daily figures against heating degree days for the same stretches. A raw month-to-month comparison is the single most common reason homeowners believe something has broken when nothing has.

Where do I find heating degree days for my part of Metro Vancouver?

Environment and Climate Change Canada publishes daily climate data by station, and degree-day totals can be taken from or calculated out of the daily mean temperatures. Choose the station closest to your home rather than a regional average, since our valleys, elevations and distance from the water produce real differences. Use the same station for both winters so the comparison stays consistent.

My bill says estimated. Does that matter?

It matters a great deal. An estimated period that came in low is corrected in the next actual read, so the following bill absorbs both periods and can look like a sudden spike. Treat an estimated bill and the actual read that follows it as one combined period, add the days together, add the energy together, and compare that against a similarly combined period from the previous winter.

How do I tell heating use apart from hot water and everything else?

Take a meter reading at the start and end of a genuinely mild stretch when the furnace has barely run. The difference is close to your non-heating gas use over those days. Divide it by the number of days, then subtract that daily figure from your winter daily figure, and what remains is your heating load.

Does a dirty filter really change the bill?

It can, because a restricted filter reduces airflow across the heat exchanger, which makes the furnace run longer to deliver the same heat and in bad cases trips the high limit and causes short cycling. Replacing a filter with the same size and type listed on the existing one is homeowner work and takes minutes. If run times stay long after a fresh filter, the restriction is elsewhere in the duct system and needs measuring.

Can a higher gas bill be a safety problem rather than just a cost problem?

Yes, and this is worth taking seriously. Incomplete combustion means the appliance is burning more fuel for less useful heat, and the same conditions that cause it can also produce carbon monoxide. If your bill rose with no weather, schedule or occupancy explanation, and especially if you have noticed soot, odours, a yellow flame or repeated lockouts, have the appliance inspected by a licensed technician rather than living with it.

Where do I find the rating information for my furnace?

On the rating plate, a metal or foil label fixed to the appliance, usually inside the front panel door or on the side of the cabinet. It lists the model, serial number and the appliance’s rated input, and the serial number is also how you establish the appliance’s age. Photograph it and keep the photo, because a technician will ask for it and the manufacturer’s documentation for that exact model is the correct source for any specification.

If I install a heat pump, does my winter-to-winter comparison still work?

No, it resets. In a dual-fuel setup, where a heat pump carries the mild shoulder seasons and the gas furnace stays as backup for cold snaps, the heating load is split across two meters and the shape of the bill changes entirely. Start a fresh baseline from the first full billing period after the changeover and build up a new set of degree-day-normalised figures from there.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.
Are BC Wide technicians licensed and insured?
Yes. BC Wide holds a TSBC gas-fitting licence, our technicians are Red Seal certified for HVAC and gas, and we carry full liability insurance and WorkSafeBC coverage.
How can I book a service call?
Call (604) 473-9690, email info@bcwide.ca, or use the booking form on bcwide.ca. Most calls are answered the same business day and we offer next-day appointments for non-emergency work.
Do you offer free estimates?
Yes. Free in-home estimates are provided for boiler, furnace, heat pump and water-heater replacements. Diagnostic visits for repairs carry a flat service fee that is credited toward the repair if you proceed.
What brands do you service?
We service all major brands including Viessmann, Navien, IBC, Rinnai, Rheem, Bradford White, Weil-McLain, Laars, Baxi, NTI, Lennox, Carrier, Bryant, Goodman, Trane, York, Daikin, Mitsubishi Electric, AO Smith, Bosch, Noritz, Giant, GSW, John Wood, and Valor.
Do you offer government rebates for heat pumps?
Yes. We are a registered contractor for BC Hydro, FortisBC and federal Greener Homes rebates. A high-efficiency heat pump installation can qualify for up to $11,000 in combined rebates depending on your home and income.
How quickly can you replace a broken hot water tank?
Standard 40 or 50-gallon gas or electric tanks are typically replaced same-day or next-day from stock. Tankless water heaters and larger commercial units usually take 1–3 business days depending on parts availability.
Why should I choose BC Wide over other HVAC companies?
BC Wide Heating & Air Conditioning has been operating in Greater Vancouver since 1999 as a TSBC-licensed (LGA90068) HVAC and gas contractor. We specialise in furnaces, boilers, heat pumps and water heaters across every major brand, we give honest options instead of upselling, and our work is performed by experienced, certified staff — not subcontractors.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote