★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Free Boiler Estimate in Delta

Boilers

Free Boiler Estimate in Delta
Home › Free Boiler Estimate in Delta

Free Boiler Estimate in Delta

Key takeaways

  • A free boiler estimate from BC Wide is an in-home visit for replacement or new installation, with no charge and no obligation; it is not a repair diagnostic.
  • The technician checks the existing boiler, the heat load of the house, venting, gas supply, piping, condensate routing, electrical and access before pricing anything.
  • You receive a written, itemised quote that names the scope, the equipment category, permits, disposal, and what is and is not included.
  • Ballpark installed ranges for Greater Vancouver: condensing gas boiler replacement about $7,000 to $15,000, gas combi boiler about $8,000 to $14,000 and up; these are not a quote.
  • Venting changes, gas line capacity, orphaned chimneys and sludge in older hydronic loops are the items that most often move a Delta boiler price.
  • Compare quotes on scope, sizing method and inclusions, not on the bottom line alone.

A free boiler estimate in Delta is an in-home visit where a TSBC-licensed BC Wide technician looks at your existing gas boiler and hydronic system, works out how much heat your house actually needs, checks the venting, gas supply, piping, condensate route, electrical and access, and then gives you a written, itemised quote for replacement or new installation. There is no charge for the visit, the consultation or the written estimate, and no obligation to go ahead. It is for installation and replacement only, not for diagnosing a repair. A typical visit takes roughly an hour to ninety minutes in a North Delta, Ladner or Tsawwassen home, and the quote arrives in writing so you can compare it line by line with any other. To book, call (604) 473-9690.

What happens during a free boiler estimate visit in Delta?

The visit follows the same order every time, because each step changes the one after it. We start with a short conversation about how the house heats now: which rooms run cold, whether the boiler also makes your domestic hot water through an indirect tank, how long the current unit has been in, and whether you are planning renovations, an addition or a suite that would change the load.

Next comes the equipment room. We look at the boiler itself, the circulators, zone valves or zone pumps, the expansion tank, the pressure relief valve, the air separator and any strainer or dirt separator. Then we follow the venting to where it leaves the house and the gas piping back toward the meter. Finally we walk the living spaces to see the emitters: fin-tube baseboard, cast iron radiators, in-floor radiant, or a mix. The type of emitter decides what water temperature the system needs, and that decides how well a condensing boiler will actually condense in your house.

Before we leave, we tell you what we found, what options make sense, and what questions are still open. The written quote follows once the measurements and heat-loss numbers are worked through, so the price is based on your house rather than a guess made in the driveway.

  • Conversation about comfort problems, hot water use and future plans
  • Inspection of the existing boiler, controls and near-boiler piping
  • Venting route, termination options and chimney condition
  • Gas supply path from the meter, and other gas appliances sharing it
  • Room-by-room walk to record emitters, windows and insulation for a heat-loss calculation
  • Condensate drain options, electrical supply and access for removal and delivery

What do we look at in Delta homes specifically?

Delta’s housing is not uniform, and that shows up in boiler jobs. Many homes here in North Delta are split-levels and basement-entry houses from the 1960s through the 1980s, and a number of them still run the original hydronic loop, sometimes with a boiler that has already been replaced once. In Ladner and Tsawwassen we see more ranchers, crawlspace foundations and later townhouse complexes, where the boiler may sit in a garage, a utility closet or a tight crawlspace. Each of those settings changes how equipment gets in and out and where venting can go.

Much of Ladner and the Boundary Bay side sits on low, flat ground close to the water. Where a boiler lives in a crawlspace or garage, we note whether it sits high enough off the floor and whether the space stays damp, because moisture shortens the life of controls and burner components. Salt-laden air near the bay can also be harder on exterior vent terminations and anything metal outside the wall, so we look at the condition of what is out there now.

Metro Vancouver water is soft. In a closed hydronic loop that means the problems we find are sludge and corrosion rather than limescale: black magnetite in the water, rusty expansion tanks, seized zone valves. What the old boiler and piping tell us about that sludge decides whether the quote includes a system flush and a dirt separator, which matter more to a new high-efficiency boiler than to the heavier cast iron unit it replaces.

What we checkWhat it tells usWhy it can change the quote
Age and type of the existing boilerWhether it is atmospheric, sealed combustion or already condensingDecides how much venting and piping must change
Water drawn from a bleed pointClear, rusty or black water shows how much sludge is in the loopHeavy sludge calls for flushing and a dirt separator
Chimney and shared ventingWhether a gas water heater shares the flue with the old boilerRemoving the boiler can leave the water heater needing a liner
Gas piping from the meterWhether the existing line can carry the new load with other appliances runningAn undersized line has to be upsized or rerouted
Emitter type in each roomWhat water temperature the house needs on a cold dayAffects boiler choice, controls and outdoor reset setup
Floor drain or condensate routeWhere acidic condensate can goNo nearby drain means a condensate pump and extra piping
Access and clearances around the unitHow the old boiler comes out and the new one goes inTight crawlspaces and stairs add labour time

What should you have ready before the estimate?

You do not need to prepare much, but a few things make the visit faster and the quote more accurate. Clear a path to the boiler and around it, and make sure we can reach the gas meter and the outside wall where the current vent exits.

  • Any paperwork on the existing boiler: install date, invoices, past service records
  • A rough list of rooms that run cold or hot, and whether it is worse on certain floors
  • Whether the boiler also heats your domestic hot water, and how many people use it
  • Plans for renovations, a suite, new windows or added insulation in the next few years
  • Your electrical panel location, since the new boiler and controls need a proper circuit
  • If you live in a townhouse or strata, a copy of the bylaws or any council approval process for exterior wall penetrations
  • Questions about rebate or incentive eligibility, so we can point you to what to check

What does the written boiler estimate include?

A useful quote tells you exactly what you are paying for and what you are not. Ours is written and itemised so you can hold it up against another contractor’s and see the differences instead of guessing at them.

We describe the equipment category rather than hiding behind a model number alone: condensing boiler or combi boiler, heating only or with an indirect tank, and the control strategy. We also note the sizing basis, meaning the heat-loss calculation, not the size of the old unit. Many older Delta boilers were oversized when installed, and simply matching the old nameplate is one of the most common reasons a new system short-cycles.

The estimate states how long the price holds. Equipment and material costs move, so the validity window is printed on the quote itself; if you need more time to decide, ask and we will confirm whether the price still stands or needs updating.

  • Removal and disposal of the old boiler and any abandoned components
  • The new boiler category, controls and outdoor reset sensor where applicable
  • Venting: new route, materials, termination location and any chimney liner work
  • Gas piping changes or upsizing, with the gas permit through Technical Safety BC
  • Near-boiler piping, circulators, expansion tank, air and dirt separation
  • Condensate neutraliser and drain or pump
  • System flush and chemical treatment if the loop needs it
  • Electrical connection scope, and what would require an electrician
  • Commissioning, combustion testing and a walkthrough of how to use the controls
  • Exclusions, stated plainly, such as drywall repair or strata-required work

How much does a boiler replacement cost in Delta?

In ballpark terms, a condensing gas boiler replacement in Greater Vancouver, installed and before GST, commonly falls in a range of about $7,000 to $15,000. These are ballpark figures for orientation only and are not a quote; an accurate price needs a site visit, which is exactly what the estimate is for.

A gas combi boiler installation, which heats the house and supplies domestic hot water from one appliance, commonly runs in a range of about $8,000 to $14,000 and up. When the existing gas line needs to be replaced or extended to serve the new boiler, that portion alone often sits around $500 to $1,500 for a short, accessible run and $1,500 to $3,000 or more for a long or difficult one.

The width of those ranges is honest. What decides where your house lands is the work around the boiler, not the box itself. Permit fees are set by the municipality or Technical Safety BC and are listed separately on the quote without guesswork.

Rebate and incentive programs for higher-efficiency equipment change over time and have their own eligibility rules. We describe what may apply when we write your estimate, but we do not put a number on it, and you should confirm eligibility directly with the program before you count on it.

  • Venting changes: moving from a chimney to a sidewall or roof vent, or relining a chimney for an orphaned water heater
  • Gas line capacity: whether the existing pipe can carry the boiler alongside the range, fireplace or water heater
  • Condensate routing: a nearby floor drain versus a pump and a long drain run
  • Hydronic condition: flushing a sludged loop, replacing corroded valves, adding a dirt separator
  • Piping changes: converting an old gravity or single-zone layout to a properly separated primary and secondary arrangement
  • Electrical: a dedicated circuit or controls wiring that the old unit did not have
  • Access: crawlspace installs, narrow stairs or a garage mechanical room with limited room to work
  • Code upgrades triggered by the replacement, such as clearance or combustion air corrections
  • Adding an indirect hot water tank or moving to a combi boiler

How do you compare two boiler quotes fairly?

Put the quotes side by side and compare scope before price. A lower number often means something is missing: no system flush, no dirt separator, venting that reuses old material, or a boiler sized from the old nameplate instead of a heat-loss calculation.

Ask each contractor the same questions. How did you size the boiler? Where will the vent terminate, and is that location allowed on my wall? What happens to the water heater that shares the chimney? Who pulls the gas permit? Is the loop being flushed? What controls are included, and will the boiler run on outdoor reset so it condenses as often as your emitters allow?

Check the licence. In BC, gas work must be done by a licensed gas fitter working under a contractor licensed with Technical Safety BC. BC Wide holds licences LGA0090068 and CGA0028029. We are an independent contractor, not a factory-authorised dealer or warranty centre, so we recommend equipment on the fit to your house, and we service the major brands found in Delta homes.

Finally, look at who does the commissioning and what the handover includes. A boiler that is installed but never combustion-tested and set up for the house will run, but it will not run the way the quote promised.

What happens after you accept a boiler estimate?

Once you accept, we confirm the equipment order, book the install date and apply for the gas permit. If you are in a strata, the owner checks the bylaws and gets any council approval needed for exterior vent work before we schedule; we cannot tell you what a strata allows. Questions about a heritage property in older parts of Ladner go to the City of Delta.

Most straightforward replacements are completed in one to two days, longer when venting, gas piping or loop repairs are extensive. You will be without heat for part of that time, so we plan the timing with you. After installation the system is filled, purged of air, combustion-tested and commissioned, the permit inspection is arranged, and we walk you through the thermostat and controls.

When should you call a licensed technician instead of waiting for an estimate?

An estimate is for planning a replacement. Some situations cannot wait for that, and some should never be handled by a homeowner at all.

Homeowners may safely do a few things: check that the thermostat has power and is calling for heat, confirm the boiler’s electrical switch is on, look at the pressure gauge and write down what it reads, and note any water on the floor. Anything past that, including opening the burner compartment, adjusting gas pressure, touching gas valves or connections, working on venting, or draining and refilling a pressurised loop, belongs to a licensed technician.

Call us at (604) 473-9690 when there is no heat, water leaking from the boiler or piping, the relief valve discharging, scorch marks around the burner area, or frequent resets. We book same-day work where we can, depending on the day’s schedule, but we do not promise a guaranteed arrival window.

  • Smell of gas: leave the house first, then call from outside
  • Carbon monoxide alarm sounding: get everyone out and call from outside
  • Pressure relief valve spraying or dripping steadily
  • Water pooling under the boiler or at pipe joints
  • Soot, scorching or melted wiring near the burner
  • Boiler locking out repeatedly on cold days
Gas & carbon-monoxide safety: Gas boilers burn natural gas and produce carbon monoxide, an odourless gas that can be deadly. Install a working CO alarm on every level of the home and near sleeping areas, and test them regularly. If you smell gas, do not operate switches, appliances or phones inside; leave the house, then call from outside. If a CO alarm sounds, get everyone out and call for help from outside. Gas piping, venting, burner and gas valve work in BC must be performed by a licensed gas fitter under a Technical Safety BC permit, and homeowners should never open the combustion chamber or alter venting.

Frequently asked questions

Is the boiler estimate really free?

Yes. There is no charge for the in-home visit, the consultation or the written estimate, and there is no obligation to go ahead. The estimate is for replacement or new installation; it is not a repair diagnostic.

Which parts of Delta do you cover for boiler estimates?

We cover North Delta, Ladner and Tsawwassen, along with the rest of Metro Vancouver, from our base in Burnaby. Call (604) 473-9690 and we will book a time that suits you.

Can you just match the size of my old boiler?

We size from a heat-loss calculation, not from the old nameplate. Many older boilers were oversized when installed, and copying that size causes short-cycling and wasted fuel. Any renovations, new windows or insulation since the original install also change the load.

Should I switch to a combi boiler?

It depends on your hot water use and the house. A combi boiler makes sense when hot water demand is moderate and space is tight, while a heating boiler with an indirect tank often suits larger households better. We explain both options on the estimate when both genuinely fit.

How long is the written estimate valid?

The validity window is printed on the quote itself because equipment and material costs change. If you need more time to decide, ask and we will confirm whether the price still stands or needs updating.

Do you handle the gas permit?

Yes. As a TSBC-licensed gas contractor we apply for the gas permit and arrange the inspection. Permit fees are set by Technical Safety BC or the municipality and are listed separately on the quote.

My townhouse is in a strata. Can you still quote?

Yes, we can inspect and quote. Exterior vent penetrations and equipment changes may need strata approval, so check your bylaws and speak with council before the install is scheduled. We cannot tell you what your strata allows.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote