★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Free Boiler Estimate in Port Coquitlam

Boilers

Free Boiler Estimate in Port Coquitlam
Home › Free Boiler Estimate in Port Coquitlam

Free Boiler Estimate in Port Coquitlam

Key takeaways

  • The in-home visit and the written estimate cost nothing and carry no obligation; they are for boiler replacement or new installation, not for repairing a boiler that has stopped working.
  • A sound quote starts with a room-by-room heat loss calculation, not a copy of the old boiler’s nameplate, because many older boilers were oversized for the house.
  • In many Port Coquitlam homes the biggest variables are venting (especially a chimney shared with a water heater), gas line capacity, condensate routing and the condition of the existing hydronic loop.
  • Metro Vancouver water is soft, so older hydronic systems here usually suffer from sludge and corrosion rather than limescale; flushing and dirt separation belong in the quote.
  • A good written estimate itemises equipment, venting, gas piping, electrical, controls, permit, disposal and start-up testing so two quotes can be compared line by line.

A free boiler estimate in Port Coquitlam is an in-home visit, typically about an hour, where a TSBC-licensed gas technician from BC Wide looks at your existing gas boiler, the way it vents, the gas supply feeding it, the room it sits in and the heating loop it serves, then sends you a written, itemised quote for replacing it or installing a new one. There is no charge for the visit or for the written estimate, and nothing to sign on the day. The visit covers installation and replacement planning only; if your boiler has quit and needs repair, that is booked as a repair visit, which we explain when you call (604) 473-9690. You finish the visit knowing what size and type of boiler your house actually needs, what has to change around it, and roughly what the job involves before you commit to anything.

What happens during a free boiler estimate visit in Port Coquitlam?

It starts on the phone. We ask what you have now (a boiler on its own, a boiler that also heats your tap water, or a boiler with a separate gas water heater), roughly how old the house is, and whether you are replacing a boiler that is failing or planning ahead. That lets the technician arrive with the right questions rather than a sales script.

At the house we walk every heated room and note what delivers the heat: hydronic baseboard convectors, cast-iron radiators or in-floor radiant tubing. We measure rooms, windows and exterior walls and ask about insulation and any renovations, because those numbers feed a heat loss calculation. Then we spend most of the time in the mechanical room and outside: the boiler itself, the chimney or vent, the gas meter and piping, the electrical supply to the boiler, and where condensate from a high-efficiency boiler could drain.

We also listen. Cold bedrooms, a bathroom floor that never warms, banging pipes and running out of hot water are all clues about zoning, pump sizing or controls, and they shape what goes into the quote. The written estimate typically follows within a few business days, and you are never asked to decide on the spot.

What do we look at in a typical Port Coquitlam home?

Many homes in the older parts of Port Coquitlam, around Mary Hill, Glenwood and Lincoln Park for example, were built between the 1960s and the 1980s. Where those houses have hot-water heat, we often find an older atmospheric boiler venting into a masonry or metal chimney, sometimes sharing that chimney with a gas water heater. Homes on the slopes of Citadel Heights and Oxford Heights, and the many townhouse complexes built later, tend to put the boiler in a garage or a tight mechanical closet, and some of them run in-floor radiant heat that needs its own mixing and controls.

Location matters too. Port Coquitlam sits where the Coquitlam and Pitt Rivers meet the Fraser, closer to the mouth of the Fraser Valley than the western half of the region, and during arctic outflow events it can run colder and windier than neighbourhoods nearer the water in Vancouver. We account for that in the heat loss design and in where a sidewall vent terminal goes, since a windy exposure can push the condensate plume back against siding or a neighbour’s window.

The old unit tells a story. The rating plate gives its age and input. Scorch marks at the draft hood point to flue gas spillage. Rust streaks, a dripping relief valve or dark, sludgy water from a drain valve tell us about the loop’s condition. A waterlogged expansion tank or a noisy circulator tells us which parts can be reused and which should be replaced with the boiler.

What we checkWhat we are looking forHow it can change the quote
Existing boiler and rating plateAge, type (atmospheric, mid-efficiency or condensing), signs of spillage or leaksDecides whether venting and near-boiler piping change completely or partly
Chimney or ventWhether a water heater shares the chimney, liner condition, a workable sidewall routeA water heater left alone on the chimney may need a liner; a new vent route adds labour
Gas meter and pipingMeter capacity, pipe run to the boiler, other gas appliances on the same lineA combi boiler or a relocated boiler may need a larger or new gas line
Condensate pathA floor drain or suitable point for acidic condensate, room for a neutraliserA long run or a condensate pump adds parts and labour
Heating loop and emittersHydronic baseboard, radiators or radiant floor, number of zones, water conditionSludge calls for flushing and a dirt separator; radiant floors need mixing controls
Electrical supplyA proper circuit and service switch for the boiler and pumpsMay need a licensed electrician to add or correct the circuit
Space and accessStairs, doorways, closet size, crawlspace or garage locationTight access affects which boiler fits and how many labour hours the job takes
Domestic hot waterSeparate water heater, indirect tank or combi boilerChanges the equipment list and the total gas load

What should you have ready before the estimate?

You do not need to prepare much, and please do not open the boiler cabinet, touch the gas valve or remove any panels before we arrive. Clearing a path is the most useful thing you can do.

  • Clear access to the boiler, the gas meter, the electrical panel and the outside wall or roof where the vent exits.
  • Any paperwork you have: service records, the original installation date, earlier permit documents or the receipt from the last boiler.
  • A short list of comfort problems by room, such as cold bedrooms, a floor that never warms or pipes that bang when the heat comes on.
  • Your hot water habits: how many people live there, whether you run out, and whether you would like the boiler to take over hot water.
  • Plans for the next few years, such as a renovation, a secondary suite, new windows or a sale, because they affect sizing and zoning.
  • For townhouses and other strata homes, your strata council contact and the bylaws covering alterations and exterior penetrations, so you can confirm with council what applies before installation is booked. We assess the technical side only and do not interpret bylaws.
  • A year of gas bills if they are handy; they help us sense-check the heat loss result.

What does the written boiler estimate include?

The estimate is itemised so you can see what you are paying for and hold it up against another contractor’s quote. It typically lists:

  • The heat loss result and the boiler type and output chosen from it, with more than one option where it makes sense.
  • Venting: the vent type, the route and termination location, and what happens to a water heater left on the old chimney.
  • Gas piping changes, if any, from the meter or an existing branch.
  • Condensate drain routing and the neutraliser.
  • Near-boiler piping, circulator pumps, expansion tank, air separation and dirt separation.
  • System flushing and water treatment for the existing loop.
  • Controls: outdoor reset sensor, thermostats and zone controls.
  • Electrical work and who performs it.
  • The permit and the inspection.
  • Removal and disposal of the old boiler.
  • Start-up and testing: combustion analysis, a carbon monoxide check, control set-up and a walkthrough with you.
  • Warranty: the manufacturer’s equipment terms as the manufacturer sets them, and the labour warranty BC Wide provides, both in writing.
  • Exclusions, such as drywall patching, strata approvals or an electrical panel upgrade if one turns out to be needed.

How long is the estimate valid, and who is writing it?

Every written estimate shows the date it was prepared and how long its pricing holds. Equipment prices and availability shift through the year, so if you come back after that window we re-confirm the numbers with you before booking rather than simply honouring an old figure.

BC Wide Home Services Ltd has served Metro Vancouver from Burnaby since 1999 and holds Technical Safety BC gas contractor licences LGA0090068 and CGA0028029. We are an independent contractor, not a factory-authorised dealer or warranty centre for any manufacturer, so the estimate may offer boilers from more than one brand we service, and we explain the differences in plain terms rather than pushing one badge.

How much does a boiler replacement cost in Port Coquitlam?

Here are ballpark ranges for Greater Vancouver, installed and before GST. A condensing gas boiler replacement typically falls somewhere between $7,000 and $15,000. These are ballpark figures for orientation only and are NOT a quote; an accurate price needs a site visit, which is exactly what the estimate appointment is for.

A gas combi boiler, which heats the house and also makes hot water on demand, usually lands in a ballpark of $8,000 to $14,000 and up. Where the boiler is relocated or the existing gas supply is undersized, a new gas line adds roughly $500 to $1,500 for a short, accessible run and $1,500 to $3,000 or more for a long or difficult one.

Program money is left out of these ranges. Rebate and incentive programs change often, so the estimate notes which ones may be worth checking rather than putting a number on them. Permit fees are set by Technical Safety BC or the municipality and appear on the estimate as they apply. What moves your number within those ranges is mostly the work around the boiler:

  • Venting: replacing a chimney-vented atmospheric boiler with a sealed-combustion condensing unit means a new vent route, and a gas water heater left on the old chimney often needs a liner so it still drafts properly.
  • Gas line capacity: a combi boiler draws heavily when making hot water, and piping sized decades ago for smaller loads may need upsizing or a new run.
  • Condensate: condensing boilers produce acidic condensate that needs a neutraliser and a drain; no drain nearby means a condensate pump.
  • Loop condition: decades of operation leave sludge and corrosion debris, which call for flushing, a dirt separator and sometimes new pumps, valves or an expansion tank.
  • Controls and zoning: adding outdoor reset, splitting a house into zones, or mixing for in-floor radiant.
  • Electrical: a dedicated circuit or a proper service switch, done by a licensed electrician.
  • Access and location: a tight townhouse closet or a crawlspace takes more labour, and moving the boiler adds piping, gas and venting work.
  • Code upgrades: correcting existing gas piping, venting or relief valve discharge found during the visit.
  • Removal and disposal, including care around old pipe insulation in older homes, which may need testing before it is disturbed.

How do you compare two boiler quotes fairly?

Put the quotes side by side and go line by line. A lower total that leaves out venting, flushing or the permit is not cheaper; it simply moves those costs to later, or leaves them undone. Check each of these:

  • Was a heat loss calculation done, and is the result stated? A quote that matches the old nameplate is a guess, and an oversized condensing boiler short-cycles and rarely condenses.
  • Is the venting fully described, including what happens to a water heater left on the chimney?
  • Are gas piping, condensate, electrical work and the permit included, or listed as possible extras?
  • Is flushing and dirt separation included? With soft Metro Vancouver water, sludge and corrosion debris, not limescale, are what clog a new boiler’s heat exchanger early.
  • Are the controls equivalent, including outdoor reset, thermostats and zoning?
  • Who takes out the permit, and is the installer a licensed gas contractor with Technical Safety BC? Ask for the licence numbers.
  • Does start-up include a combustion analysis and a carbon monoxide check?
  • What labour warranty is offered in writing, and who registers the manufacturer’s warranty?
  • What is excluded?

Can you get a boiler estimate the same day, or if your boiler has failed?

We offer same-day estimate visits where we can, depending on the schedule and where technicians are working that day. During a cold snap demand rises sharply across the region, so we will tell you honestly when the earliest realistic slot is, and we never promise a guaranteed arrival window.

If your boiler has stopped in the middle of winter, say so when you call. Sometimes a repair visit gets heat back sooner than a replacement, and sometimes the boiler is past saving; either way we explain which kind of visit fits. If replacement is the right call, the estimate also covers timing, including whether the recommended equipment is in stock locally.

A smell of gas or a sounding carbon monoxide alarm is not an estimate situation at all. That is an emergency: leave first, then call.

When should you call a licensed technician instead of waiting for an estimate?

Some signs mean the boiler needs attention now, whatever your replacement plans are:

  • Any smell of gas near the boiler, meter or piping.
  • A carbon monoxide alarm, or headaches, nausea or dizziness that several people in the house share and that ease when outside.
  • Soot, scorching or discoloured paint near the draft hood or vent connector.
  • Water discharging from the relief valve, or the pressure gauge climbing well above its normal reading.
  • Water leaking from the boiler cabinet or near the burner.
  • The burner firing and shutting off repeatedly, or repeated lockouts.
  • A flame that looks yellow, lazy or lifted off the burner, if it is visible through a sight glass.
Homeowner may doLicensed technician only
Read the pressure gauge and note the readingOpen the burner compartment or combustion chamber
Check the thermostat and confirm the service switch is onAdjust or replace the gas valve or burner parts
Bleed air from radiators, if you know howAlter, disconnect or reroute venting
Keep the area around the boiler clear and dryMove, extend or pressure-test gas piping
Test carbon monoxide alarms monthlyElectrical work inside the boiler or a new circuit
Gas & carbon-monoxide safety: Gas and carbon monoxide safety: a gas boiler burns natural gas and vents combustion gases outdoors, and a damaged vent, a blocked terminal or a failing heat exchanger can let carbon monoxide into the home. Install carbon monoxide alarms on every level of the house, including near sleeping areas, and test them regularly. If you smell gas, do not operate switches, appliances or phones inside; leave the building, then call your gas utility’s emergency line or 911 from outside and wait there. If a carbon monoxide alarm sounds or people feel unwell, get everyone into fresh air and call 911. In BC, gas work including boiler installation, gas piping and venting is restricted to licensed gas fitters working under a permit; homeowners should never open the burner compartment, adjust the gas valve or modify the vent.

Frequently asked questions

Is the boiler estimate really free?

Yes. There is no charge for the in-home visit or the written estimate, and no obligation to go ahead. The visit is for planning a boiler replacement or new installation; if your boiler needs repair, that is booked as a repair visit, and we explain how that works when you call (604) 473-9690.

How long does the estimate visit take?

Typically about an hour for a detached home with one or two zones. Larger homes, multiple zones, radiant floors or a complicated vent route can take longer. The written quote usually follows within a few business days.

Will you just replace my boiler with the same size?

Not automatically. We size the new boiler from a heat loss calculation for your house as it is today, because many older boilers were oversized and many homes have since had new windows or insulation. An oversized condensing boiler cycles on and off constantly and rarely runs in its efficient condensing range.

Can the new boiler also make my hot water?

Yes, either as a combi boiler that heats water on demand or as a boiler feeding an indirect storage tank. Each suits different households, and a combi often needs more gas capacity, so the estimate shows whether your gas line can support it. Keeping a separate gas water heater is also a valid option we will price.

Do I need a permit for a boiler replacement in Port Coquitlam?

Yes, gas appliance replacement requires a gas permit and an inspection. We take out the permit as part of the job. Permit fees are set by Technical Safety BC or the municipality and are shown on the estimate as they apply.

I live in a townhouse. Can a new boiler vent through the side wall?

We can tell you whether a sidewall route is technically workable and where the terminal would need to go. Whether your strata permits it is a question for your strata council and bylaws, so please confirm with council before installation is booked.

How long is the quote valid?

Each written estimate states the date it was prepared and how long its pricing holds. Equipment prices and availability change, so if you come back after that window we re-confirm the numbers with you before booking.

Are you a dealer for a particular boiler brand?

No. BC Wide is an independent TSBC-licensed contractor, not a factory-authorised dealer or warranty centre. We install and service several brands and can quote more than one option, explaining the differences neutrally so the choice is yours.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote