★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Free Boiler Estimate in West Vancouver

Boilers

Free Boiler Estimate in West Vancouver
Home › Free Boiler Estimate in West Vancouver

Free Boiler Estimate in West Vancouver

Key takeaways

  • The in-home boiler estimate and the written quote are free and carry no obligation; they cover replacement and new installation, not repair.
  • A TSBC-licensed gas fitter checks your heat load, the existing boiler, venting, gas supply, hydronic piping, condensate route and mechanical-room access before pricing anything.
  • In many West Vancouver homes the price is driven by venting, access and the condition of old piping more than by the boiler itself.
  • The written estimate itemises equipment, venting, gas work, piping, water treatment, permits, removal and disposal, and states how long the price holds.
  • Compare quotes on identical scope: sizing method, venting, water treatment, gas capacity, permits and written warranty handling, not the bottom line alone.

A free boiler estimate in West Vancouver is an in-home visit where a TSBC-licensed gas fitter from BC Wide looks at your existing hydronic system, works out how much heat the house actually needs, checks the venting, gas supply, piping and access to the mechanical room, and then sends you a written, itemised price for replacing your gas boiler or installing a new one. There is no charge and no obligation for the visit or the written estimate. It is for replacement and installation work only: if your boiler has stopped working and needs repair, that is a separate service call, and we tell you so before booking. To arrange a visit, call (604) 473-9690.

What happens during a free boiler estimate visit in West Vancouver?

Most visits take about an hour, and longer in a large home with several heating zones or radiant floors. We follow the same order every time so nothing is missed and so two homes can be compared honestly.

  • A short conversation first: what bothers you about the current system, which rooms run cold or overheat, how your household uses hot water, and whether renovations are planned.
  • A look at the existing boiler: its type, approximate age from the rating plate, how it vents, and the condition of the circulator pumps, expansion tank, relief valve and zone controls.
  • A heat-loss assessment: we measure rooms and note windows, insulation, ceiling heights and past renovations, because the right boiler size comes from the house, not from the old boiler’s label.
  • Venting and gas supply: where a new vent could exit, whether a water heater would be left alone on the chimney, and whether the gas meter and piping can carry the new appliance.
  • Piping and emitters: baseboard, cast-iron radiators, in-floor radiant or a mix, since each works best at different water temperatures and needs different controls.
  • Access: the route from the driveway to the mechanical room, stairs, doorway widths and how the old boiler comes out.

What do we look at in West Vancouver homes specifically?

Many homes here were built between the 1950s and the 1970s on sloped lots, from post-and-beam West Coast modern houses in the British Properties and Caulfeild to split-levels around Ambleside and Dundarave. A good share were designed around hydronic heat from the start, often with radiant tubing in concrete slabs or perimeter baseboard, and many still run on an original or second-generation boiler.

Hillside lots shape the job. Mechanical rooms are often on a lower level reached by exterior stairs or a steep driveway, which affects how new equipment goes in and how a heavy old unit comes out. Long gas runs from a street-side meter to a boiler at the back of the house are common, and they need to be checked for capacity before a higher-input or combi boiler is added.

Older slab radiant systems deserve extra attention. Some early installations used tubing without an oxygen barrier, or steel piping that has corroded over decades, and Metro Vancouver’s soft water does not protect against that. The result is sludge, largely iron oxide, circulating through the system. A modern condensing boiler with fine heat-exchanger passages does not tolerate dirty water well, so flushing, a dirt or magnetic separator, and water treatment often appear on West Vancouver estimates. Limescale is rarely the concern here; sludge and corrosion are.

Near the waterfront in areas such as Dundarave and Horseshoe Bay, salt air is hard on exterior vent terminations and metal fittings, so we look closely at where a new vent can exit and how exposed it will be. Larger homes sometimes have a pool, spa or snow-melt loop tied into the boiler, and those loads change the design.

For townhouses and other strata homes, any exterior vent penetration or change to common property is a matter for your strata council under your bylaws. We tell you what the installation would need, and you confirm it with council before work is scheduled. If your home carries a heritage designation, questions about visible exterior changes go to the District of West Vancouver.

What does the old boiler tell us about the new installation?

The existing system is the best evidence we have. What we see around it often explains cold rooms and noisy pipes, and it tells us what has to change for a new boiler to last.

What we seeWhat it usually meansHow it shapes the estimate
Boiler vents into a masonry chimneyAn older non-condensing, atmospheric designA condensing replacement needs new sidewall or roof venting, and a water heater left on the chimney may need a liner
Rust streaks, weeping fittings or a stained floorCorrosion, failed seals or a failing heat exchangerPiping repairs or replacement sections may be added to the scope
Black or brown water from a drain valveSludge circulating through the systemPower flushing, a dirt or magnetic separator, and water treatment
Relief valve that has dripped or dischargedExpansion tank or system pressure problemsA new expansion tank and pressure controls priced in
Many zone valves or several circulatorsA zoned system, often added to in stages over the yearsNear-boiler piping redesign, often with a hydraulic separator or primary-secondary piping
An indirect hot water tank connected to the boilerDomestic hot water is boiler-fed todayOptions to keep the tank, replace it, or move to a combi boiler
Cold rooms at the ends of long runsUnbalanced distribution or trapped airBalancing, purging and possibly added controls or emitters
Boiler far larger than the heat-loss resultOversized original equipment that short-cyclesA smaller modulating boiler, which can also ease the gas supply requirement

What should you have ready before the boiler estimate?

A little preparation makes the visit shorter and the quote more accurate. None of this is required, but each item removes a guess.

  • Clear access to the boiler, the gas meter, the electrical panel and any manifolds or zone controls.
  • Past service records or notes from earlier repairs, if you have them.
  • A list of rooms that run cold or overheat, and any banging, gurgling or hissing you hear from the pipes.
  • Your hot water habits: how many people live in the home, soaker tubs, and whether hot water runs out.
  • Renovation plans: an addition, a secondary suite, new windows or new flooring over radiant tubing all change the design.
  • Anything else tied into the system, such as pool or spa heating, snow melt or a garage unit heater.
  • For strata homes, your property manager’s contact or the relevant bylaws, so you can take our requirements to council.
  • House plans or renovation drawings, which show where piping runs inside walls and floors.

What does the written boiler estimate include, and how long is it valid?

The estimate we send after the visit is itemised, so you can see exactly what you are paying for and compare it line by line with any other quote.

  • Boiler type: condensing or non-condensing, heat-only or combi, and why that type suits your home.
  • Sizing basis: confirmation that the size comes from a heat-loss calculation, not from matching the old label.
  • Venting: the new vent route, materials, termination location, and any chimney liner for appliances left on the chimney.
  • Gas work: the connection, any piping upgrade needed to carry the load, and the pressure test.
  • Hydronic piping: near-boiler piping, pumps, expansion tank, air separation, relief valve and zone control changes.
  • Water quality: flushing, a separator or filter, and system treatment.
  • Condensate: a neutralizer and the drain route, or a condensate pump where there is no nearby drain.
  • Controls: an outdoor reset sensor and thermostat work.
  • Electrical: the boiler’s dedicated circuit and any wiring done by the appropriate licensed trade.
  • Permits and inspection, shown as their own line. Permit fees are set by Technical Safety BC or the municipality.
  • Removal and disposal of the old boiler, and cleanup.
  • Commissioning: startup and combustion setup to the manufacturer’s instructions, plus a walk-through of the controls.
  • Warranty handling: how manufacturer warranty registration is done and what labour coverage we provide, stated in writing.

How much does a boiler replacement cost in West Vancouver?

For orientation, here are ballpark ranges for Greater Vancouver, installed and before GST. A condensing gas boiler replacement usually sits in a ballpark range of $7,000 to $15,000. These are ballpark figures for orientation only and are not a quote; an accurate price for your home needs a site visit, which is exactly what the in-home estimate is for.

A gas combi boiler installation, which heats the house and supplies domestic hot water from one appliance, usually falls in a ballpark range of $8,000 to $14,000 and up. Where the existing gas piping cannot carry the new load, a new or upgraded gas line typically adds a ballpark of $500 to $1,500 for a short, accessible run, and $1,500 to $3,000 or more for a long or difficult one.

Large West Vancouver homes with several zones, slab radiant, a pool or snow-melt loop, or difficult hillside access can sit at or above the top of these ranges. That is why our estimate explains the reasoning line by line. The main things that move the number:

  • Venting changes: moving from a chimney to sidewall or roof venting, the length and route of the new vent, and lining the chimney for a water heater left behind.
  • Gas line capacity: whether the meter and existing pipe can carry the new appliance, and how far and through what the new pipe must run.
  • Condensate routing: a nearby floor drain is simple; a mechanical room without one needs a pump and a longer drain line.
  • System condition: how much sludge and corrosion is in the piping, and whether sections of old steel or non-barrier tubing need replacing or isolating.
  • Near-boiler piping and zoning: the number of zones and circulators, and mixing for slab radiant running alongside baseboard.
  • Hot water strategy: keeping an indirect tank, replacing it, or switching to a combi.
  • Electrical: the boiler circuit and any work that needs an electrician.
  • Access and removal: exterior stairs, steep driveways, tight mechanical rooms and heavy cast-iron boilers that must be broken down to come out.
  • Code upgrades: bringing combustion air, relief valve discharge piping, bonding or clearances up to current requirements during the swap.

How do you compare two boiler estimates fairly?

The lowest total is not always the cheapest job. Two quotes can be far apart simply because one leaves items out that the other includes, and the missing items tend to show up later as change orders or early failures.

Rebate and incentive programs for high-efficiency equipment change often and depend on the equipment and your situation. We can tell you whether a program appears to apply and what paperwork it asks for, but confirm eligibility with the program itself before counting on it. If you would like to spread payments out, ask about financing options at the visit and get the terms in writing.

  • Sizing: did each contractor do a heat-loss calculation, or simply match the old boiler’s size?
  • Venting: is the route and material the same, and does each quote include a chimney liner if a water heater stays on the chimney?
  • Water treatment: does each include flushing, a separator and treatment, or just connect a new boiler to old, dirty water?
  • Gas work: does each account for gas line capacity and include the pressure test?
  • Controls: are outdoor reset and zone controls included or listed as extras?
  • Permits: is the gas permit pulled by the licensed contractor, with inspection included?
  • Removal, disposal and cleanup.
  • Licensing: ask for each contractor’s Technical Safety BC licence numbers and check them. Ours are LGA0090068 and CGA0028029.
  • Warranty handling: who registers the manufacturer warranty, and what labour coverage is written into the contract.

When should you call a licensed technician instead of waiting for an estimate?

An estimate visit is planned work. Some situations cannot wait for it: a gas smell, a CO alarm, water leaking from the boiler, a relief valve that keeps discharging, signs of scorching or soot around the burner, or no heat in cold weather. For a gas smell or CO alarm, leave the house first and call from outside. For the others, call us at (604) 473-9690. We take repair calls and do same-day work where our schedule allows, but we cannot promise a guaranteed arrival window.

What a homeowner may safely do: check the thermostat setting and batteries, confirm the boiler’s switch and breaker are on, keep the area around the boiler clear, note the pressure gauge reading, and test CO alarms. What needs a licensed gas fitter: anything involving gas valves, burners, venting or the combustion chamber, repeated relighting after a safety lockout, and any boiler replacement. Draining, refilling and treating the hydronic system is best left to a technician, and wiring changes need the appropriate licensed trade.

Gas & carbon-monoxide safety: A gas boiler burns natural gas and can produce carbon monoxide, an odourless gas that can be deadly. Install CO alarms on every level of your home and near sleeping areas, and test them regularly. If you smell gas, leave immediately without switching lights or appliances on or off, and call your gas utility’s emergency line or 911 from outside. If a CO alarm sounds, get everyone out and call 911. Never block the boiler’s vent termination or combustion air openings, and never store paint, solvents or gasoline near it. In BC, gas work must be done by a licensed gas fitter under a permit.

Frequently asked questions

Is the boiler estimate in West Vancouver really free?

Yes. The in-home visit and the written estimate for boiler replacement or installation carry no charge and no obligation. The estimate covers installation and replacement work only; if your boiler needs repair, that is a separate service we book on its own.

How long does a boiler estimate visit take?

Most visits take about an hour, longer for large homes with several zones or radiant slabs. The written, itemised estimate follows afterward, usually within a few business days and sooner for a straightforward swap.

Can you quote a boiler replacement over the phone?

We can talk through ballpark ranges over the phone, but not a price we will stand behind. Venting, gas capacity, piping condition and access vary too much between West Vancouver homes to quote without seeing them.

Should I replace my boiler with a combi boiler?

It depends on your hot water use and your current setup. A combi suits homes where one appliance can cover heating and moderate hot water demand, while a large home with several bathrooms may be better served by a heat-only boiler with an indirect tank. When both options make sense, we lay them out side by side in the estimate.

Do I need a permit to replace a boiler in West Vancouver?

Yes. Replacing a gas appliance requires a gas permit pulled by the licensed contractor, and an inspection may follow. Permit fees are set by Technical Safety BC or the municipality and appear as their own line on our estimate.

Can a new boiler reuse my existing radiant floor tubing?

Often it can, if the tubing is sound. Older tubing without an oxygen barrier or corroded steel piping may need isolating behind a heat exchanger, a thorough cleaning, or replacement of some sections, and we look for those signs during the visit.

Can you come for an estimate the same day?

Estimate visits are booked appointments, and a same-day visit happens only where our schedule allows. No-heat and leak situations are handled as repair calls and get priority, but we never promise a guaranteed arrival window.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote