★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Free Furnace Replacement Estimate in New Westminster

Furnace

Free Furnace Replacement Estimate in New Westminster
Home › Free Furnace Replacement Estimate in New Westminster

Free Furnace Replacement Estimate in New Westminster

Quick answer

A free furnace estimate in New Westminster is an in-home visit where a TSBC-licensed gas technician from BC Wide sizes the house, checks the venting, gas supply, ductwork and electrical, and then gives you a written, itemized replacement quote with no obligation. Ballpark, a high-efficiency gas furnace replacement runs $5,000 to $9,000 installed before GST, with complex jobs higher; that is orientation only, not a quote. A furnace that has stopped working needs a diagnosis instead, which is a $189.00 service call. Book at (604) 473-9690.

Key takeaways

  • A proper furnace replacement estimate is done in your home, not over the phone, because sizing, venting and gas-line capacity have to be checked on site.
  • New Westminster’s older homes in Queen’s Park, Sapperton and Brow of the Hill often hide venting, chimney and duct issues that change the scope of the job.
  • A written quote should name the equipment, list every line of installation work, and state who pulls the gas permit and arranges the inspection.
  • Compare quotes on scope and sizing method, not on the bottom line alone: a quote that skips a load calculation or a venting plan is not a like-for-like quote.
  • The estimate visit is for replacement and installation planning; it is not a repair diagnosis of a furnace that has stopped working.
  • Call (604) 473-9690 to book an in-home furnace replacement estimate anywhere in New Westminster.

A free furnace replacement estimate in New Westminster is an in-home visit where a TSBC-licensed gas technician looks at your existing furnace, measures and assesses the house, checks the gas supply, venting, ductwork and electrical connection, talks through your comfort problems and goals, and then gives you a written, itemized quote for the replacement. You are under no obligation to proceed. At BC Wide Home Services, a licensed contractor based next door in Burnaby and working in Metro Vancouver since 1999, the visit typically covers the furnace room, the supply and return registers in the living spaces, the thermostat and the vent termination outside. The point is to replace guesswork with measurements, so the furnace you choose is correctly sized, legally vented and installed to code. Below is exactly what happens during that visit, what you should have ready, what the written quote should contain and how to compare quotes from different contractors fairly.

What happens during a free in-home furnace estimate?

The visit starts with a conversation. The technician will ask how old the current furnace is, whether any rooms run cold or hot, whether the system is noisy, whether anyone in the home has allergies or dust concerns, and whether you are considering adding central air conditioning or a heat pump now or later. Those answers shape the recommendation as much as the measurements do.

Next comes the inspection. The technician looks at the existing furnace’s data plate, the venting type and route, the condition and size of the gas line feeding the appliance, the supply and return ductwork, the filter rack, the condensate drain path if the furnace is a condensing unit, and the electrical disconnect. They also look at whatever else shares the space, such as a gas water heater that may be connected to the same chimney.

Finally, they measure. A responsible estimate uses a heat-loss calculation based on the size of the house, window area, insulation levels, air leakage and orientation, rather than simply matching the size of the old furnace. Many furnaces installed decades ago were oversized, and a like-for-like swap repeats that mistake. Expect the visit to take roughly an hour for a typical detached home, longer if the ductwork is complicated.

What should I have ready before the technician arrives?

A little preparation makes the estimate more accurate and the quote more useful. You do not need technical knowledge, just clear access and a few facts about the house.

  • Clear access to the furnace, the water heater, the electrical panel and the outside vent or chimney.
  • Any paperwork on the existing furnace: install date, service records or the original invoice if you have it.
  • A list of comfort complaints by room, for example a cold upstairs bedroom or a basement suite that never warms up.
  • Recent renovations: new windows, added insulation, a finished basement or an addition all change the heating load.
  • Your plans: whether you want air conditioning, a heat pump paired with the furnace, a smart thermostat or better filtration now or down the road.
  • Strata or rental details if they apply: bylaws, landlord consent, or rules about exterior vent locations.
  • Recent gas bills if you want the technician to talk through how the old unit has been performing.

What should a written furnace replacement quote include?

A written quote is only as good as its detail. Vague quotes that say little more than new furnace installed make it impossible to compare contractors and easy for scope to change later. Use the checklist below when you read any quote, including ours.

Quote itemWhat it should sayWhy it matters
EquipmentBrand, model family, and whether it is single-stage, two-stage or modulatingLets you compare like with like and look up the manufacturer’s published specifications
Sizing basisHow the size was chosen, ideally a heat-loss calculationAn oversized furnace short-cycles, runs noisy and wastes fuel
VentingVent material, route and termination location, plus any chimney liner workVenting is a code and carbon-monoxide safety issue, not an extra
Gas pipingWhether the existing line is adequate or needs changesAn undersized gas line starves the burner and must be corrected
DuctworkPlenum transitions, return-air changes, filter rackA new furnace on restrictive ducts will not perform as designed
CondensateDrain route, and whether a condensate pump is neededCondensing furnaces produce water that must be drained properly
Thermostat and controlsWhich thermostat, and compatibility with stagingA basic thermostat can waste the benefit of a two-stage or modulating unit
Permit and inspectionWho pulls the gas permit and arranges inspectionGas appliance installs in BC must be permitted and done by licensed trades
Removal and cleanupRemoval and disposal of the old furnaceAvoids a surprise at the end of the job
Warranty and registrationManufacturer warranty terms as published and who registers the unitMany manufacturer warranties depend on timely registration

How do I compare furnace quotes from different contractors?

Line the quotes up item by item using the table above. If one quote includes a chimney liner for the orphaned water heater and another does not mention it, they are not quoting the same job. If one is based on a heat-loss calculation and another simply matches the old furnace’s size, the second has skipped a step that affects comfort for the next two decades.

Ask each contractor the same questions. How did you size this furnace? Where will the vent terminate, and does that location meet clearance rules for windows, doors and property lines? Is my gas line adequate? Will you pull the gas permit in your company’s name? What happens if you open the wall and find something unexpected? A contractor who answers clearly on the visit tends to communicate clearly during the installation too.

Cost matters, but compare it last and compare it qualitatively. A lower quote that leaves out venting corrections, gas-line work or duct changes often grows once the old furnace is pulled out. A higher-efficiency modulating furnace generally costs more up front than a basic single-stage model, and whether that is worth it depends on how long you plan to stay and how your home heats. Ask for options in writing so you can weigh them side by side, and do not sign anything you do not understand.

What is different about replacing a furnace in a New Westminster home?

New Westminster is one of the oldest cities in Western Canada, and its housing stock shows it. Many of the character and heritage homes in Queen’s Park, Sapperton, Brow of the Hill and the West End were built long before forced-air gas heat was common, and their heating systems have been converted, extended and patched over generations. It is common to find a furnace and a water heater sharing an old masonry chimney. When a new high-efficiency condensing furnace is installed, it vents separately through a plastic vent pipe, and the water heater is left alone in a chimney that is now far too large for it. That can cause poor draft and condensation, so the quote may need to include a chimney liner or a separate venting plan for the water heater.

The city’s steep slopes matter too. Homes built into the hillside often have furnaces in partly below-grade rooms with limited routes for a sidewall vent, and vent terminations have to meet clearances from windows, doors, walkways and neighbouring properties. On the tight lots common in older neighbourhoods and in Queensborough, finding a compliant termination spot is a real design question, not an afterthought.

Our mild, wet coastal climate means furnaces here run long, gentle heating seasons rather than short bursts of extreme cold. That favours correctly sized, multi-stage or modulating equipment that runs longer at lower output, which keeps rooms even and quiet. It is also why many New Westminster homeowners ask about pairing a gas furnace with a heat pump, letting the heat pump handle the milder months and the furnace take over in cold snaps. If that interests you, raise it at the estimate so the ductwork, electrical capacity and outdoor unit location can be assessed at the same visit. Homes in Queen’s Park sit inside a heritage conservation area, so if exterior changes are involved, ask early whether any city review applies before equipment is ordered.

Does the estimate cover a furnace that has stopped working?

The free estimate is for planning a replacement or new installation. It is not a repair visit, and the technician will not be troubleshooting a failed igniter or a tripped limit switch during it. If your furnace has stopped heating and you are not sure whether it can be repaired, tell us when you call so we can book the right kind of visit.

That said, if you already know you want to replace an ageing furnace, the estimate is the right first step. The technician may point out conditions on the existing system that affect the new install, such as a cracked vent connector or a corroded gas connector, and will note them in the quote.

What can a homeowner do, and what needs a licensed technician?

In BC, gas appliance installation, gas piping changes and venting work must be done by a licensed gas fitter under a permit, and most electrical work on the furnace circuit is restricted to licensed trades as well. Homeowners play an important part, but it is a limited one.

  • Homeowner: clear the area around the furnace, change or check the air filter, keep supply and return registers open and unblocked, note comfort problems, and test your carbon monoxide alarms.
  • Homeowner: gather paperwork, confirm strata or landlord approvals, and decide on priorities such as quiet operation, even temperatures or future air conditioning.
  • Licensed technician: sizing the furnace, disconnecting and reconnecting gas, altering gas piping, installing or changing venting, relining a chimney, wiring the furnace and thermostat, and commissioning the new unit.
  • Licensed technician: pulling the gas permit and arranging the inspection, then checking combustion, draft and gas pressure at start-up.

When should I call a licensed technician instead of waiting for an estimate?

Some situations should not wait for a scheduled estimate. If you smell gas, leave the home immediately and call FortisBC’s emergency line from outside, then a licensed contractor. If your carbon monoxide alarm sounds, get everyone outside and call 911. If you see scorch marks near the furnace, soot around the vent, a burner flame that is lazy, yellow or lifting, or water pooling under the furnace, shut the furnace off at the thermostat and call a licensed technician.

For planned replacement, the best time to book an estimate is before the furnace fails. Late summer and early fall give you time to compare quotes, sort out permits and schedule the installation without going cold. Call BC Wide at (604) 473-9690 to book an in-home furnace replacement estimate in New Westminster.

Gas & carbon-monoxide safety: Gas and carbon monoxide safety: a gas furnace burns fuel and produces carbon monoxide, an odourless gas that can be deadly. Install working CO alarms on every sleeping level and near the furnace room, and test them regularly. Never block the furnace’s air supply, store chemicals or paint beside it, or run it with panels removed. If you smell gas, do not operate switches or appliances; leave the home and call FortisBC’s emergency line from outside. If a CO alarm sounds or anyone feels dizzy, headachy or nauseous indoors, get everyone out and call 911. Gas connections, venting and furnace installation in BC must be carried out by a licensed gas technician under a permit.

Frequently asked questions

Is the furnace replacement estimate really free and without obligation?

Yes. The in-home replacement estimate and the written quote come with no obligation to go ahead. It covers planning a new or replacement furnace, not repair troubleshooting of a furnace that has broken down.

Can I get an accurate furnace quote over the phone?

Not reliably. Sizing depends on a heat-loss assessment of your home, and the venting route, gas-line capacity and ductwork all have to be seen in person. A phone figure usually leaves out exactly the items that change the scope of the job.

How long does a furnace estimate visit take?

For a typical detached New Westminster home, plan on roughly an hour. Older homes with complicated ductwork, basement suites or a shared chimney can take longer because there is more to inspect and measure.

Should I just replace my furnace with the same size unit?

Not automatically. Many older furnaces were oversized, and matching them repeats the problem of short cycling, noise and uneven temperatures. A heat-loss calculation tells you what the house actually needs, especially if windows or insulation have been upgraded.

What happens to my water heater if I install a high-efficiency furnace?

If the old furnace and a gas water heater shared a chimney, the new condensing furnace will vent separately and the water heater may be left in an oversized chimney. The quote should address this with a chimney liner or another venting solution, which is common in New Westminster’s older homes.

Who pulls the gas permit for a furnace replacement?

The licensed gas contractor doing the work should pull the permit and arrange the inspection. Your written quote should say so clearly; if it does not, ask before you sign.

Can I ask about a heat pump or air conditioning at the same visit?

Yes, and it is the best time to do it. Ductwork, electrical capacity and the location of an outdoor unit can be assessed alongside the furnace, and the quote can show the furnace alone and paired with cooling or a heat pump.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

Free furnace estimate New Westminster: ballpark costs and what moves the price

Here are the ballpark installed ranges we work from for New Westminster homes, in Canadian dollars, for Greater Vancouver work before GST. Most high-efficiency gas furnace replacements land between $5,000 and $9,000, and complex jobs go higher. These are ballpark figures for orientation only and are not a quote; an accurate price needs a site visit, which is exactly what the in-home estimate is for.

The range is wide on purpose. Two houses on the same block can need very different installations, and the furnace itself is usually not the biggest variable. What sits around it is.

  • Venting: a high-efficiency condensing furnace vents through plastic pipe, usually out a side wall, and the termination has to meet clearances from windows, doors, the property line and the gas meter. On a tight lot that can mean a longer run or a roof termination.
  • The orphaned water heater: when an older furnace that shared a masonry chimney with a gas water heater comes out, the water heater is often left alone in a chimney now too large for it. It may need a liner or other venting change, and that belongs on the quote.
  • Gas supply: the gas line and meter have to carry the new furnace plus every other gas appliance at the same time. Undersized piping is found on site, not over the phone.
  • Condensate: a condensing furnace makes water. It needs a drain path, sometimes a condensate pump, and protection from freezing if it runs through a garage or crawlspace.
  • Electrical: a furnace needs a proper dedicated circuit and service switch. Adding a heat pump for dual fuel may need panel space or a panel upgrade.
  • Ductwork and return air: an undersized return or a poorly matched plenum makes a new furnace noisy and less efficient. Transitions and return upgrades are priced as separate line items.
  • Access and removal: narrow basement stairs, crawlspaces, attics and strata parkades add labour. Removal and disposal of the old unit should be listed.
  • Permits and inspection: a gas permit and inspection are required. Permit fees are set by each municipality or Technical Safety BC, and the quote should say who pulls the permit.
  • Equipment tier: single-stage, two-stage and modulating furnaces, and constant-torque versus variable-speed blowers, sit at different points in the range. So does the thermostat you choose.
JobBallpark installed range, before GSTWhat usually decides where it lands
High-efficiency gas furnace replacement, straightforward swap$5,000 to $9,000Equipment tier, whether venting and return air can be reused, access to the furnace room
Complex furnace replacement (relocation, new vent route, tight crawlspace or attic)$9,000 to $13,000 and upExtra labour hours, new vent and condensate routes, duct transitions
Adding a heat pump to an existing gas furnace (dual fuel)$10,000 to $18,000Outdoor unit location, line-set length, electrical panel capacity; a panel upgrade is extra when needed
New gas line for an appliance, short and accessible$500 to $1,500Pipe length, meter and supply capacity, open versus finished ceilings
New gas line, long or difficult route$1,500 to $3,000 and upDistance, number of fittings, pipe sizing for the whole-house gas load

Free furnace estimate New Westminster: what we check first, and the signs owners notice

When we walk in, the first look is at the existing furnace’s data plate and age, then the venting and chimney, then the gas piping back toward the meter. After that we look at the ductwork and return air, the electrical feed and thermostat, and the space the new unit has to fit through and into. Only then do we sit down and talk about how the house actually feels, because the comfort complaints usually point to the real scope.

These are the things New Westminster owners tell us when they call for an estimate. None of them on its own means the furnace must be replaced, and sorting that out honestly is the point of the visit:

  • The upstairs never gets warm, even with the thermostat turned way up.
  • It has started banging when it lights, or the blower rattles or squeals.
  • Our gas bills keep climbing and nothing else in the house has changed.
  • It shuts off and starts again every few minutes.
  • There is rust, water or a white crust around the bottom of the furnace.
  • We have had repeat service calls over the last couple of winters for the same kind of problem.
  • The furnace is original to the house, or nobody knows how old it is.
  • The house is dusty and some rooms feel stuffy no matter which filter we use.

Repair or replace, and is it safe to wait? How a diagnostic visit and a replacement estimate differ

The in-home estimate is free, and it exists to plan a furnace replacement or a new installation. A furnace that has stopped working is a different job. It needs a technician to test the ignition sequence, flame sensing, pressure switches, limits, the control board, the blower and the venting to find the actual fault. Diagnostic service calls are $189.00. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation.

Gas and carbon monoxide safety comes first. If you smell gas, the rotten-egg odour, leave the house without switching lights or appliances on or off, and call your gas utility’s emergency line or 911 from outside. Every home with a gas furnace should have working carbon monoxide alarms near the sleeping areas; if one sounds, get everyone outside and call 911. A yellow, lazy or wavering burner flame, soot around the furnace, or headaches that ease when you leave the house are reasons to shut the furnace off and call a licensed technician, not to wait for an estimate.

Owner-safe checks that are fine to do before we arrive: confirm the thermostat is set to heat with fresh batteries, check the breaker and the furnace service switch, replace a clogged filter, make sure the furnace door is fully seated, and clear leaves or debris from the outdoor intake and exhaust pipes. Anything involving the gas valve, burners, ignition, control board, venting or gas piping is work for a licensed gas fitter in BC.

Plenty of furnaces are worth repairing, and we will tell you when one is. The decision comes down to a handful of things we write down for you:

  • Age compared with a typical gas furnace service life, and how hard the unit has been worked.
  • The heat exchanger: a cracked or failing heat exchanger is a carbon monoxide risk and usually ends the repair conversation.
  • Parts: whether parts for an older model are still available, or only through long special orders.
  • Repair history: one failed igniter is normal wear; the third major repair in two winters is a pattern.
  • The size of the repair compared with the replacement range above, weighed against how many good years the furnace realistically has left.
  • Comfort and efficiency: if the house was never comfortable, a repair returns you to the same problem.

Furnace estimates across New Westminster neighbourhoods: Queen’s Park to Queensborough

New Westminster packs a lot of housing types into a small city, and the neighbourhood often hints at what we will find in the furnace room. These are general patterns, not rules, and every house gets checked on its own.

  • Queen’s Park: many older character and heritage homes. Expect original masonry chimneys, older duct runs that were added or rerouted over the years, and exterior vent locations that may need extra care on a heritage facade.
  • Sapperton: a mix of older houses and newer infill. Low basement ceilings and tight furnace closets are common, and older homes often share a chimney between the furnace and water heater.
  • The West End: many post-war and mid-century houses with basement furnaces. Shared chimneys and return-air systems that were never sized generously come up often.
  • Glenbrook North: established family homes, many renovated more than once. Renovations sometimes closed in ducts or boxed in gas lines, which affects access and routing.
  • Connaught Heights: older bungalows alongside larger rebuilt homes near the Burnaby side. Larger homes can bring longer gas runs and zoning questions.
  • Queensborough: on Lulu Island, with many newer homes and townhouses. Venting is often simpler, but crawlspaces, attached garages and strata rules on exterior terminations need attention.
  • Uptown: a mix of apartments, townhouses and older houses. Strata approval for vent locations and equipment placement can set the timeline.

How the free furnace estimate in New Westminster works, step by step

From your first call to the final inspection, a New Westminster furnace replacement follows the same order:

  • Call (604) 473-9690 or email info@bcwide.ca to book the in-home estimate; we book same-day where we can.
  • A licensed gas technician visits, measures the house, checks venting, gas supply, ducts and electrical, and listens to your comfort goals.
  • You receive a written quote before any work starts, listing the equipment, every line of installation work, removal and disposal, who pulls the permit, and the warranty terms in writing.
  • You decide with no pressure; if anything changes in scope, it is added in writing before work proceeds.
  • We pull the gas permit, install the furnace, then start it up, check combustion and gas pressure, and confirm airflow and condensate drainage.
  • The installation is inspected as the permit requires, and we walk you through the thermostat, the filter and what normal operation looks like.

Who does the work, and which furnace brands do you service in New Westminster?

BC Wide Home Services is an independent contractor based next door in Burnaby, licensed by Technical Safety BC under licence LGA0090068 with Class B gas licence CGA0028029, and rated 4.7 stars from 181 Google reviews. The people who quote your furnace are licensed gas fitters, every installation is permitted and inspected, and the written quote comes before the work.

We service and install the major gas furnace brands found in Metro Vancouver homes, including Carrier, Lennox, Trane, Goodman, Rheem, York, Bryant, Daikin, Amana and American Standard. We are not a factory dealer for any of them, so the recommendation follows your house, your budget and parts support in the Lower Mainland rather than a sales target. If a heat pump makes sense, we quote it as dual fuel, paired with a gas furnace that carries the house through cold snaps.

These are ballpark prices, not a quote. For exact pricing on your home, call BC Wide at (604) 473-9690 or email info@bcwide.ca.

More questions homeowners ask

Is a furnace estimate really free in New Westminster?

Yes, when the visit is to plan a furnace replacement or a new installation. A licensed technician assesses the house and you get a written, itemized quote with no obligation to go ahead. A furnace that has stopped working needs a diagnostic service call, which is $189.00, and that charge is waived if you then replace the furnace through BC Wide.

How much does a new furnace cost in New Westminster BC?

Ballpark, a high-efficiency gas furnace replacement runs about $5,000 to $9,000 installed before GST, and complex jobs with new venting or difficult access go higher. That is orientation only, not a quote. Venting, gas line sizing, condensate routing, electrical, ductwork and access decide where your home lands.

How long does a furnace replacement take in New Westminster?

A straightforward swap in an accessible basement is usually a single working day, including start-up and combustion checks. Relocations, new vent routes, gas line work or strata approvals add time. The written quote should tell you what the installation day involves and what has to happen before it.

Do I need a permit to replace a furnace in New Westminster?

Yes. Replacing a gas furnace requires a gas permit and an inspection, and electrical work may need its own permit. The licensed contractor should pull the permit and arrange the inspection, and the quote should say so in writing.

Should I get a furnace estimate before my old furnace fails?

Yes, if the furnace is old, has needed repeat repairs, or the house has never been comfortable. Planning ahead lets you compare equipment, sort out venting or gas line issues and schedule the work, instead of deciding in a cold house. Booking is same-day where we can.

What does a furnace estimate near me in New Westminster actually check?

A proper estimate checks the heat load of the house, the venting and chimney, gas supply and pipe sizing, ductwork and return air, the electrical feed, condensate drainage and access for removal and installation. If any of those is skipped, the price is a guess. Call (604) 473-9690 to book a visit.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote