★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Free Furnace Replacement Estimate in Tsawwassen

Furnace

Free Furnace Replacement Estimate in Tsawwassen
Home › Free Furnace Replacement Estimate in Tsawwassen

Free Furnace Replacement Estimate in Tsawwassen

Quick answer

A free furnace estimate in Tsawwassen is an in-home visit by a licensed BC Wide gas fitter to plan a replacement, ending in a written quote. Most high-efficiency gas furnace replacements fall in a ballpark of $5,000 to $9,000 installed, before GST, with complex jobs higher. These are ballpark figures for orientation only, not a quote; an accurate price needs a site visit. The estimate itself is free. A broken furnace is a diagnostic call: diagnostic service calls are $189.00.

Key takeaways

  • A proper replacement estimate happens in your home, not over the phone, because sizing, venting and ductwork all have to be checked in person.
  • The written quote should name the exact furnace model, the sizing method used, the venting plan, the permit and every piece of included work.
  • Tsawwassen homes are often 1960s to 1980s builds with crawlspaces, older chimneys and ducts that were never resized, which changes the scope of a replacement.
  • Salt air near Boundary Bay and the Strait of Georgia is hard on outdoor vent terminations and outdoor equipment, so terminal location matters.
  • Compare quotes line by line on scope, not on the bottom line alone, and ask each contractor to confirm who pulls the gas permit.
  • BC Wide Home Services is an independent TSBC-licensed contractor; call (604) 473-9690 to book an in-home estimate.

A free furnace replacement estimate in Tsawwassen is an in-home visit where a licensed gas technician looks at your current furnace, measures the house, checks the gas supply, venting and ductwork, asks how the home actually heats, and then gives you a written quote that spells out exactly what will be installed and what work is included. It is not a repair call and it is not a diagnosis of a broken furnace; it is a planning visit for replacement. Expect it to take roughly an hour or a little more, depending on how accessible the furnace room and crawlspace are. You leave the visit with no obligation and, ideally, a clear picture of your options, so you can compare contractors on what they are actually proposing rather than on a number scribbled on a business card.

What happens during an in-home furnace replacement estimate?

The technician starts with the existing equipment: the age and type of furnace, whether it is a mid-efficiency unit venting into a metal chimney or a high-efficiency condensing unit venting through plastic pipe to a side wall, and the condition of the gas piping, shut-off valve and electrical supply. They will look at the filter rack, the supply plenum and the return air path, because a new furnace connected to a restricted duct system will be noisy and will not deliver its rated performance.

Next comes the house itself. A good estimator measures rooms or reviews floor plans, notes window area and orientation, looks at attic and crawlspace insulation where they can, and asks about comfort problems: a cold basement suite, a hot upstairs bedroom, rooms that never seem to get air. That information feeds a heat-loss calculation, which is how the new furnace should be sized. Replacing a furnace with the same size as the old one simply because it was there is one of the most common mistakes in the trade.

Finally, the technician talks through options with you: single-stage versus two-stage or modulating burners, variable-speed blowers, thermostat choices, and whether a heat pump paired with the gas furnace makes sense for your home. You should be able to ask questions without feeling rushed.

What should I have ready before the estimator arrives?

A little preparation makes the visit faster and the quote more accurate. None of these items are mandatory, but each one removes a guess from the estimate.

  • Clear access to the furnace, the gas meter, the electrical panel and any crawlspace hatch.
  • The furnace model and serial number if you can read the rating plate safely, or a photo of it.
  • Recent gas bills, which help the estimator understand how hard the current system is working.
  • A list of comfort complaints by room, including any basement suite or addition.
  • Any renovation history: added rooms, finished basements, replaced windows, new insulation.
  • Strata bylaws or council rules if you live in a townhouse or strata complex, since vent locations and outdoor equipment may need approval.
  • Your plans for the next few years, such as adding air conditioning or a heat pump, finishing the basement or selling.

What should a written furnace replacement quote include?

A verbal number is not a quote. The written document is what you will compare, and it is what protects you if something is left out. The table below lists what a complete quote should cover and why each line matters. Pricing itself is something to discuss directly with the contractor; the important part here is that every line of scope is visible.

Quote itemWhat it should sayWhy it matters
EquipmentBrand, exact model number, burner type and blower typeLets you check the published specifications and warranty yourself
Sizing basisHow the size was chosen, ideally a room-by-room heat-loss calculationOversized furnaces short-cycle; undersized ones struggle on cold nights
VentingNew vent route, termination location and whether an old chimney is lined or abandonedVenting errors are a combustion and carbon monoxide risk
Gas pipingWhether existing piping is adequate or needs changes, plus a new shut-off valve if requiredUndersized gas supply causes poor burner performance
CondensateWhere condensate drains and whether a pump or neutralizer is includedHigh-efficiency furnaces produce acidic water that must be handled properly
Ductwork and plenumTransitions, return air changes, filter rack and any duct modificationsRestricted ducts cause noise and uneven heating
Permit and inspectionWho pulls the gas permit and that the work will be inspected as requiredUnpermitted gas work can cause insurance and resale problems
Removal and disposalRemoval of the old furnace and site cleanupAvoids surprise extra charges on install day
Warranty and registrationManufacturer warranty terms as published, labour coverage and who registers the unitMany manufacturer warranties require timely registration

Why does a Tsawwassen home change the scope of a furnace replacement?

Tsawwassen has a distinct housing mix. Much of the single-family stock around the English Bluff, Beach Grove and Pebble Hill areas dates from the 1960s through the 1980s: split-levels, ranchers and two-storey homes, many with crawlspaces and original sheet-metal ductwork. Newer townhouse and strata developments near the town centre and on Tsawwassen First Nation lands add a different set of constraints, from tight mechanical closets to strata rules on vent placement.

Older homes here often have a mid-efficiency furnace venting into a shared or masonry chimney. Moving to a condensing furnace usually means a new plastic vent through a side wall, and it can leave a gas water heater alone in an oversized chimney, which may need a liner or its own venting solution. A good estimate addresses the water heater venting at the same time rather than leaving it as a surprise.

The climate matters too. Tsawwassen is one of the drier, sunnier corners of Metro Vancouver, but it is still a mild, damp coastal climate with long shoulder seasons. That favours furnaces that can run gently at low fire for long periods, and it makes a heat pump paired with the furnace worth discussing for many homes. Salt air off Boundary Bay and the Strait of Georgia also accelerates corrosion on outdoor metal, so the vent termination location and any outdoor unit placement should account for exposure and wind.

Permitting is the last local wrinkle. For most addresses in Delta, gas permits run through Technical Safety BC, but authority can differ on Tsawwassen First Nation lands and for some strata situations. A licensed contractor should confirm the correct permitting authority for your specific address before work is scheduled.

How do I compare furnace replacement quotes fairly?

Put the quotes side by side and compare scope first. If one quote includes a heat-loss calculation, a new vent, a chimney liner for the water heater, condensate handling and a permit, and another quote lists only the furnace and installation, they are not describing the same job. The lower total may simply be missing work that will be added later.

Then compare the equipment itself. Look up each model number and compare burner staging, blower type and the published warranty. A two-stage or modulating furnace with a variable-speed blower is a different product from a single-stage furnace with a basic blower, even if both carry a similar efficiency label.

Finally, compare the people. Ask each contractor to confirm their Technical Safety BC licence, who will do the installation, who pulls the permit and how warranty service is handled. A contractor that sizes carefully and explains the reasoning is usually the one that installs carefully.

  • Same furnace size in every quote? Ask each contractor how they arrived at it.
  • Is the venting plan written down, including where the vent exits the house?
  • Is the gas water heater venting addressed if the chimney is being abandoned?
  • Are ductwork changes included or listed as possible extras?
  • Is the permit included, and in whose name?

How does the estimator help me choose the right furnace?

Choosing a furnace is mostly about matching the equipment to the house and to how you live in it. An estimator should explain what the efficiency rating means: AFUE describes how much of the gas energy ends up as heat in the home over a season, and condensing furnaces reach higher ratings by pulling extra heat out of the flue gases. The exact rating for any model is manufacturer-published and should be verified on the specification sheet.

Beyond efficiency, burner staging and blower design drive comfort. A single-stage furnace is either fully on or off. A two-stage furnace runs at low fire most of the time and steps up only on colder nights. A modulating furnace adjusts in small increments. Paired with a variable-speed blower, the higher-end options deliver quieter, more even heat, which is noticeable in split-level homes where upstairs and downstairs fight each other.

If you are considering air conditioning now or later, the estimator should check whether the new furnace’s blower and the duct system can support a cooling coil. That is also the moment to discuss a heat pump paired with the gas furnace, where the heat pump handles mild weather and the furnace takes over when it is cold. Thermostat choice should follow the equipment: staged and modulating furnaces work best with a thermostat designed to control them.

When should I call a licensed technician instead of waiting for an estimate?

An estimate is a planning visit. Some situations cannot wait for planning and need a licensed gas technician right away. In BC, gas work, venting changes and most electrical work on a furnace are legally restricted to licensed trades. A homeowner may change the filter, keep the area around the furnace clear, check that the thermostat has power and settings are correct, and look at the vent terminal outside for snow, leaves or nests. Opening the burner compartment, adjusting gas pressure, replacing controls or altering venting is technician work.

  • You smell gas, or your carbon monoxide alarm sounds: leave the home first and call from outside.
  • You see soot, scorching or rust streaks around the furnace or vent connector.
  • The furnace repeatedly shuts down, or the flame looks yellow, lazy or unsteady.
  • Water is pooling around a high-efficiency furnace or the condensate line is blocked.
  • The vent pipe is disconnected, cracked or sagging.
Gas & carbon-monoxide safety: Gas and carbon monoxide safety: if you smell rotten eggs or natural gas, do not operate switches, phones or appliances inside the home. Leave immediately, then call FortisBC’s emergency line and 911 from outside. Carbon monoxide is colourless and odourless, so every home with a gas furnace, gas water heater or gas fireplace should have working CO alarms near sleeping areas and on each level. A furnace replacement changes venting, gas piping and combustion air, so it must be done by a TSBC-licensed gas fitter under a permit and inspected as required. Homeowners should never open the burner compartment, adjust gas pressure or modify venting.

Frequently asked questions

Is a furnace replacement estimate the same as a repair visit?

No. A replacement estimate is a planning visit to measure your home and quote new equipment and installation. It is not a diagnosis of a malfunctioning furnace. If your furnace is not working, ask about a repair visit separately.

How long does an in-home furnace estimate take in Tsawwassen?

Most visits take about an hour, sometimes longer if there is a crawlspace to inspect or a basement suite with its own comfort issues. The time goes into measuring the home, checking venting and gas supply and talking through options with you.

Can I get an accurate furnace quote over the phone?

Not reliably. Sizing, vent routing, gas piping and ductwork condition all have to be checked in person. A phone number is a guess, and the gaps usually show up as extras on installation day.

Should the new furnace be the same size as my old one?

Not necessarily. Many older furnaces were oversized, and homes change as windows and insulation are upgraded. A heat-loss calculation is the right way to size the new furnace, and your quote should say how the size was chosen.

Do I need a permit to replace a furnace in Tsawwassen?

Yes, furnace replacement is gas work that requires a permit and a licensed gas fitter. For most Delta addresses the permit runs through Technical Safety BC, but authority can differ on Tsawwassen First Nation lands, so your contractor should confirm it for your address.

What happens to my gas water heater if the furnace no longer uses the chimney?

The water heater may be left alone in a chimney that is too large for it, which can affect draft. The quote should address this, typically with a liner or a separate venting solution, so it is not missed.

Which furnace brands does BC Wide install?

We are an independent TSBC-licensed contractor, not a factory-authorized dealer, and we service and install a range of major gas furnace brands. The estimator will recommend specific models based on your home and explain the reasoning in the written quote.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

Free furnace estimate Tsawwassen: what does a new furnace cost?

Homeowners usually want a number before they book, so here are the ballpark installed ranges we work from in Greater Vancouver. They are installed prices, before GST and before any rebate. They are ballpark ranges, not a quote: the real figure comes out of the site visit, because the same furnace can be a straight swap in one house and a re-vent, re-pipe and duct correction in the house next door.

Complex jobs, such as moving the furnace to a new location, rebuilding a return-air system or replacing a long section of undersized gas pipe, can sit above the top of these ranges. When that happens we explain on the quote exactly which line items took it there.

What moves the price on a Tsawwassen furnace job is mostly the work around the furnace, not the box itself:

  • Venting: going from an older mid-efficiency furnace to a condensing furnace means new plastic venting to an outside wall and a terminal placed to code; a long or awkward route adds labour.
  • Condensate routing: a condensing furnace makes water that must reach a drain; crawlspace and attic installs often need a condensate pump.
  • Gas supply: the gas line has to carry the new furnace plus every other gas appliance in the house at the same time; undersized pipe is corrected before the furnace is lit.
  • Access: crawlspaces, attics and tight closets add hours for removal and installation.
  • Ductwork and return air: a starved return or badly leaking ducts are corrected or flagged in writing, because a new furnace on bad ducts still heats unevenly.
  • Electrical: a dedicated circuit and service switch are code items, and a dual-fuel heat pump may need more panel capacity.
  • Permits: a gas permit is required; permit fees are set by each municipality or Technical Safety BC, and the permit is listed on our quote.
  • Equipment tier: single-stage, two-stage and modulating furnaces differ in price and in how evenly and quietly they heat.
  • Removal and code upgrades: hauling away the old furnace, and dealing with an old chimney if a gas water heater is left venting alone into it.
JobBallpark installed range, before GSTWhat usually pushes it toward the top
High-efficiency gas furnace replacement$5,000 to $9,000New venting route, duct corrections, tight crawlspace or attic access
Adding a heat pump to an existing gas furnace (dual fuel)$10,000 to $18,000Electrical panel upgrade when needed (extra), line-set length, outdoor unit placement
New gas line for an appliance, short and accessible$500 to $1,500Distance from the meter, number of fittings, open versus finished ceilings
New gas line for an appliance, long or difficult$1,500 to $3,000 and upLong runs, upsizing existing pipe, opening finished walls or ceilings

Free furnace estimate Tsawwassen: what we check first

Most people who book a replacement estimate describe the problem in plain words, and those words tell us where to look first. These are the reasons we hear most often in Tsawwassen homes:

  • The furnace is old and I would rather replace it on my schedule than in a cold snap.
  • Some rooms are always cold and others are too hot.
  • It got loud: banging at start-up, rattling, or a new whine from the blower.
  • Our gas bills keep climbing and nothing else in the house has changed.
  • It turns on and off every few minutes.
  • There is water on the floor around the furnace.
  • We are renovating or adding a room and want heat that matches the new layout.
  • We want to add air conditioning or a heat pump and are not sure the furnace can support it.

What happens if my furnace is broken, not just old?

On the visit we start with the rating plate and the condition of the existing furnace, then the venting and chimney, the gas line and meter, the return air and duct sizes, the electrical supply, and where condensate can drain. Only after that do we measure the house for a heat-loss calculation, because the answer to the sizing question depends on what the house and ducts can actually deliver.

The free estimate is a planning visit for replacing or installing equipment. If your furnace has stopped working, is locking out or is showing a fault, that is a diagnostic service call, not an estimate. Diagnostic service calls are $189.00. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived, taken off the installation.

What a homeowner can safely do before calling: replace or check the furnace filter, confirm the thermostat is set to heat with fresh batteries, make sure the furnace service switch and breaker are on, and clear snow, leaves or debris from the outside vent and intake pipes. Anything behind the burner door, the gas valve, the venting, the igniter, the control board and the wiring is work for a licensed gas technician.

Gas and carbon monoxide safety: if you smell gas, leave the house first, do not touch light switches, and call your gas utility’s emergency line or 911 from outside. If a carbon monoxide alarm sounds, get everyone outdoors and call 911. A yellow or lazy flame, soot around the furnace or a hot, burning smell are reasons to shut the furnace off and call for service rather than wait for an estimate. Every home with a gas furnace should have working CO alarms near the sleeping areas.

Should I repair or replace my furnace? How the cost logic works

The decision is rarely about one repair bill. It is about how much life the furnace has left after the repair, whether the repair fixes the actual complaint, and whether the parts are still sensible to source. We put both options in writing when both are reasonable, and we tell you plainly when one of them is not.

  • Repair usually makes sense when the furnace is mid-life, one component has failed, the heat exchanger is sound and the house heats evenly when it runs.
  • Replacement starts to make sense when the same furnace keeps failing, parts are hard to find, or the repair would not fix uneven heat or noise that comes from sizing or ductwork.
  • A cracked or failing heat exchanger is a safety finding, not a repair to defer; on an older furnace it almost always ends in replacement.
  • If you plan to add air conditioning or a dual-fuel heat pump in the next few years, replacing an old furnace with one designed to pair with it can avoid paying for two separate projects.
  • Comfort complaints caused by undersized returns or leaky ducts are fixed in the ductwork, and a new furnace alone will not cure them.

Furnace replacement in English Bluff, Beach Grove, Pebble Hill, Boundary Bay and the town centre

Tsawwassen is small, but the housing changes from one part of town to the next, and so does the scope of a furnace job. These are patterns we watch for, not rules, and every house is confirmed on the visit.

English Bluff: homes here are often larger, and many have been added onto over the years. Additions are where we find rooms that were never properly ducted, so sizing and return air get extra attention. Homes facing the Strait of Georgia also take more wind, which matters for where a vent terminal can go.

Beach Grove: a mix of older, smaller homes and newer rebuilds close to the water. Crawlspace furnaces and damp under-floor spaces are common in the older houses, which affects condensate routing and how we protect equipment and venting from moisture and salt air.

Pebble Hill: largely family homes, many of them split-levels and two-storey houses from the decades when much of Tsawwassen was built. Ducts were usually sized for the original furnace, so a new furnace has to be matched to what those ducts can move rather than simply upsized.

Boundary Bay: near the bay, salt air is hard on outdoor vent terminals and on the outdoor half of a dual-fuel heat pump. Terminal placement, corrosion-resistant mounting and keeping equipment clear of drifting debris are part of the plan.

Tsawwassen town centre: more townhouses and newer multi-family buildings. Strata rules can control where venting and outdoor units go, so we tell you on the quote what needs strata approval before the work is scheduled.

Who does the work, and how does it go from estimate to first heat?

BC Wide Home Services Ltd is an independent contractor licensed by Technical Safety BC, licence LGA0090068, holding Class B gas licence CGA0028029, and serving Metro Vancouver since 1999. We are rated 4.7 stars from 181 Google reviews. Installations are done by licensed gas fitters, under a gas permit, and inspected. You get a written quote before any work starts.

We service and install gas furnaces from brands including Lennox, Carrier, Bryant, Trane, American Standard, Goodman, Rheem, York, Daikin and Napoleon. These are brands we service as an independent contractor; we are not a factory dealer for any of them, so the quote recommends the furnace that fits your house, not a quota.

How the process runs, step by step:

  • Call (604) 473-9690 or email info@bcwide.ca. We ask about the furnace, the house and what is bothering you, and book the in-home estimate.
  • On site, we inspect the existing furnace, venting, gas supply, ducts, electrical and drainage, and measure the house for sizing.
  • You receive a written quote naming the furnace model, the sizing method, the venting plan, gas line work, condensate routing, electrical work, the permit, removal of the old unit, what is excluded, and the warranty terms written on the quote itself.
  • You decide in your own time. There is no obligation from the estimate.
  • Once you approve, we pull the gas permit and schedule the install. For urgent replacements we do it same-day where we can.
  • On install day we remove the old furnace, set and pipe the new one, run venting and condensate, then start it up, check combustion and gas pressure, test for carbon monoxide and walk you through the thermostat and filter.
  • The permit is closed with an inspection, and your paperwork stays with the house.

More questions homeowners ask

Is a furnace estimate really free in Tsawwassen?

Yes, the in-home estimate for replacing or installing a furnace is free and carries no obligation. It is a planning visit that ends in a written quote, not a repair or diagnostic visit. If your furnace is not working, that is a diagnostic service call, and diagnostic service calls are $189.00.

How much does a new gas furnace cost in Tsawwassen BC?

A high-efficiency gas furnace replacement usually falls in a ballpark of $5,000 to $9,000 installed, before GST, with complex jobs higher. Venting, gas line sizing, condensate routing, access and ductwork decide where your home lands. That range is for orientation only and is not a quote; the in-home estimate gives you the real number in writing.

Do you charge to diagnose a furnace that stopped working in Tsawwassen?

Yes. Diagnostic service calls are $189.00, and the only free service is the estimate for replacing or installing equipment. If the diagnosis leads to a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation.

Can I get a furnace estimate near me in Tsawwassen the same day?

Same-day where we can. Call (604) 473-9690 early in the day and tell us whether the furnace still runs, because a no-heat home is handled as a service call first. If you smell gas or a CO alarm sounds, leave the house and call your gas utility’s emergency line or 911 before calling us.

Do I need a permit to replace a furnace in Tsawwassen?

Yes, a furnace replacement is gas work and needs a gas permit and an inspection. We pull the permit as the licensed contractor and list it on the quote. Permit fees are set by each municipality or Technical Safety BC, so we show the permit as a line item rather than guessing a figure.

Should I add a heat pump when I replace my furnace in Tsawwassen?

For many Tsawwassen homes a dual-fuel setup makes sense: a heat pump handles most of the mild, wet coastal season and the gas furnace takes over in cold snaps. Adding a heat pump to a gas furnace is usually a ballpark of $10,000 to $18,000 installed, with a panel upgrade extra when one is needed. Incentive programs change through the year, and we explain at the estimate which ones a dual-fuel system might qualify for.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote