★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Furnace Replacement in Steveston, Richmond

Furnace

Furnace Replacement in Steveston, Richmond
Home › Furnace Replacement in Steveston, Richmond

Furnace Replacement in Steveston, Richmond

Key takeaways

  • Replacement usually makes sense when an older furnace needs a major part, has a cracked heat exchanger, or keeps failing each winter.
  • Many Steveston homes have no full basement, so furnaces often sit in crawlspaces, utility closets, garages or attics, which shapes the size and style of the new unit.
  • Switching from a chimney-vented furnace to a high-efficiency condensing furnace means new plastic venting and a condensate drain, and the old chimney may need a liner for any water heater left on it.
  • Townhouses and strata homes often need strata approval and careful vent-termination planning before a new furnace can go in.
  • A gas permit and a licensed gas fitter are required in BC; homeowners should never disconnect or reconnect gas appliances themselves.
  • BC Wide provides a free in-home estimate and a written quote; call (604) 473-9690.

Furnace replacement in Steveston usually makes sense when your gas furnace is well into its service life and needs an expensive repair, shows a cracked or corroded heat exchanger, or has become unreliable enough that you no longer trust it through a wet Richmond winter. The job itself is shaped by the house: many Steveston homes sit on crawlspaces or slabs rather than full basements, so the furnace is often tucked into a closet, garage, attic or crawlspace, and newer townhouses near the waterfront have tight mechanical rooms and strata rules about where vents can exit. A proper replacement covers sizing, venting, the gas supply, the condensate drain, the ductwork connection and a gas permit, all done by a licensed gas fitter. BC Wide, a TSBC-licensed contractor serving Metro Vancouver since 1999, handles furnace replacements across Richmond; call (604) 473-9690 for a free in-home estimate.

When does replacing a furnace make more sense than repairing it?

Most furnaces give warning before they give out. The decision is rarely about one symptom; it is about the age of the unit, the cost of the part it needs, the safety of the heat exchanger and how often you have been calling for service.

A furnace that needs a small, inexpensive part such as an igniter or flame sensor is usually worth repairing even if it is older. A furnace that needs a control board, an inducer motor or a blower motor late in its life deserves a harder look, because those are among the more expensive parts and the next failure is rarely far behind. A cracked heat exchanger on an older furnace is almost always a replacement, because the heat exchanger is the barrier between combustion gases and the air you breathe.

What you are seeingWhat it often meansRepair or replace?
Furnace clicks and tries to light, then shuts offDirty flame sensor, weak igniter or venting faultUsually repair; a technician confirms the cause
Repeated breakdowns every heating seasonMultiple aging components wearing out togetherOften replace; compare repair history to a written quote
Rust, soot or scorch marks near the burnersPoor combustion, venting problems or moisture damageNeeds inspection before any decision; can indicate replacement
Technician reports a cracked heat exchangerCombustion gases can leak into the airstreamReplace; the unit should not be run
Uneven heat and rising gas billsAging equipment, poor airflow or ductwork leakageCheck ducts and filter first, then evaluate the furnace
Loud rumbling, squealing or bangingDelayed ignition, failing blower bearing or loose partsShut down and call; repair or replace depends on the part

What kinds of homes in Steveston affect a furnace replacement?

Steveston grew from a fishing and cannery village at the mouth of the Fraser River, and its housing reflects several eras side by side. Many streets carry older character houses and post-war bungalows, alongside larger family homes from later decades, and closer to the waterfront and village core there is a good share of newer townhouses and low-rise strata buildings.

Richmond sits on low-lying delta land with a high water table, so many homes here were built without full basements. That single fact changes where furnaces live. In older and mid-century homes the furnace is often in a crawlspace, a main-floor utility closet or an attached garage. In many newer townhouses it sits in a compact mechanical closet or, in some designs, in an attic space. Each of those locations limits what size and style of furnace fits, how the vent can run and how easily a technician can service it later.

Near the river mouth, homes also take more wind and salt-laden air than inland Richmond. Outdoor vent terminations, sidewall caps and any outdoor equipment can corrode faster, which is worth checking on older installations and planning for on new ones.

What does a furnace replacement involve in a crawlspace, closet or garage?

The work follows the same sequence in every home, but the location decides how long each step takes and what has to be modified.

  • Load calculation and sizing: the new furnace is sized to the home’s actual heat loss, not simply matched to the old nameplate. Many older furnaces were oversized, which causes short cycling and uneven comfort.
  • Choosing the configuration: furnaces are built as upflow, downflow or horizontal units. A crawlspace or attic usually needs a horizontal furnace; a main-floor closet feeding ducts below the floor may need a downflow unit. Getting this wrong forces awkward duct transitions.
  • Gas shut-off and removal: a licensed gas fitter isolates the gas supply, disconnects the old furnace and removes it. Crawlspace removals are slow, physical work and sometimes require access panels to be enlarged.
  • Venting: the vent system is replaced or modified to suit the new furnace and inspected along its full run.
  • Plenum and duct connections: new transitions are fabricated so the furnace mates cleanly with existing supply and return ducts, and joints are sealed.
  • Condensate drain: a condensing furnace produces water that must drain to an approved location; in a crawlspace this may need a condensate pump.
  • Gas connection, start-up and combustion check: the gas line is reconnected, tested for leaks, and the furnace is commissioned, including checking gas pressure, temperature rise and safe venting.
  • Thermostat and handover: the thermostat is connected or upgraded, and you are shown how to change the filter and what to watch for.

How does venting change when I replace an older furnace?

Older mid-efficiency furnaces in many Steveston houses vent hot combustion gases up a metal flue or masonry chimney, often shared with a gas tank water heater. High-efficiency condensing furnaces work differently: they extract so much heat that the exhaust is cool and wet, so it cannot go up the old chimney. Instead it runs through sealed plastic venting, usually out a sidewall or through the roof, with a separate pipe bringing in combustion air.

That switch creates two planning questions. First, where can the new vent terminate? Building and gas codes set clearances from windows, doors, soffits, property lines, walkways and gas meters, and on a narrow lot or a townhouse wall those clearances can be hard to meet. Second, what happens to the old chimney? If the water heater stays on it, the chimney may now be too large for that single appliance, which can cause poor draft and condensation; a liner or a vent modification is often needed. Your installer should address both before the quote is final, not on installation day.

In attic installations, venting and condensate lines need protection against cold, and the furnace needs a safe service platform and clear access. In homes close to the water, stainless or corrosion-resistant termination hardware is worth discussing.

What is different about replacing a furnace in a Steveston townhouse or strata home?

Townhouses near the Steveston waterfront are often tight on space and governed by strata bylaws. Before any work starts, check whether your strata requires written approval for mechanical changes, new wall penetrations or changes to exterior appearance. Moving a vent termination from the roof to a sidewall, or adding a new penetration for a condensing furnace, usually needs that approval.

Mechanical closets in newer townhouses were often designed around the original furnace’s exact dimensions. The replacement has to fit the closet, leave service clearance and keep the required combustion-air arrangement. Sometimes the right answer is a specific cabinet size or configuration rather than the most feature-rich model. Many townhouse owners also consider pairing the new furnace with a heat pump for cooling and shoulder-season heating; that adds an outdoor unit whose location will also need strata sign-off.

How does Richmond’s climate and setting affect the furnace decision?

Richmond winters are mild and wet rather than bitterly cold. Furnaces here run long, moderate cycles through damp months rather than working flat out in deep cold. That favours equipment that modulates or runs in stages, because a furnace that can run at a lower output for longer tends to deliver more even heat and quieter operation than one that blasts on and off.

Damp air is also hard on equipment in crawlspaces and garages. Moisture speeds up rust on cabinets, burners and vent connectors, and a crawlspace with poor drainage can leave a furnace sitting in humid conditions all year. During an estimate it is worth checking the crawlspace for standing water or vapour problems, because a new furnace installed in the same conditions will age the same way.

Finally, homes near the river mouth see more wind-driven rain on exposed walls. Vent terminations need to be positioned and protected so rain and wind do not interfere with combustion air intake or exhaust.

What permits are needed for a furnace replacement in Richmond?

In BC, replacing a gas furnace requires a gas permit, and the work must be done by a licensed gas contractor. Depending on the address and scope, the permit is issued either by the City of Richmond or by Technical Safety BC; your contractor should confirm which applies and obtain it. If the job includes new electrical circuits, that electrical work also falls under permit and must be done by a licensed electrician.

The permit is not paperwork for its own sake. It triggers an inspection pathway, protects you when you sell the home and may matter to your insurer if anything goes wrong. Ask any contractor to confirm in writing that the permit will be pulled and closed out.

When should I call a licensed technician, and what can I safely do myself?

Homeowners can safely change the furnace filter, keep the area around the furnace clear, check that the thermostat has power and is set correctly, check that the furnace service switch is on, and look for obvious blockages such as leaves or snow at outdoor vent terminations. That is the limit of do-it-yourself work on a gas furnace.

Everything involving the gas supply, burners, igniter, gas valve, venting, heat exchanger or internal wiring must be handled by a licensed technician. Call right away if you smell gas, if your carbon monoxide alarm sounds, if you see soot or scorch marks, if the furnace makes loud bangs on ignition, or if it keeps locking out after a reset. For replacement planning, book a free in-home estimate; a technician will measure, assess venting and access, and give you a written quote. BC Wide can be reached at (604) 473-9690.

Gas & carbon-monoxide safety: Gas and carbon monoxide safety: if you smell gas, leave the home immediately, do not operate light switches or electrical devices, and call FortisBC’s emergency line or 911 from outside. If your carbon monoxide alarm sounds, or anyone has headaches, nausea or dizziness that ease when they leave the house, get everyone outside and call 911. Every home with a gas furnace should have working CO alarms near sleeping areas, and furnace venting should be inspected by a licensed gas technician. Never attempt to disconnect, move or reconnect a gas appliance yourself; in BC this work is restricted to licensed gas fitters.

Frequently asked questions

How long does a furnace replacement take in a Steveston home?

Most straightforward replacements are completed in a day. Crawlspace and attic installations, venting changes from a chimney to plastic venting, or chimney liner work can extend the job. Your technician should give you a realistic timeline with the written quote.

Can I put a new furnace in the same crawlspace or closet as my old one?

Usually yes, as long as the new unit’s configuration, dimensions and service clearances fit the space. A crawlspace typically needs a horizontal furnace, and a tight closet may limit which cabinet sizes work. The in-home estimate is where this gets measured and confirmed.

Will I need to change my chimney if I get a high-efficiency furnace?

The new furnace will not use the chimney; it vents through sealed plastic pipe. If a gas water heater remains on the chimney, the chimney may be oversized for it alone and may need a liner or a vent modification. A licensed technician assesses this during the estimate.

Do I need strata approval to replace a furnace in a Steveston townhouse?

Often, especially when the work involves new wall or roof penetrations, relocating vent terminations or adding outdoor equipment such as a heat pump. Check your strata bylaws and get written approval before work begins. A like-for-like swap using existing venting may need less, but confirm with your strata.

How much does furnace replacement cost in Richmond?

It depends on the furnace type, the location in the home, venting changes, ductwork modifications and whether a heat pump or new thermostat is added. Because crawlspace, attic and townhouse installs vary so much, the only reliable figure is a written quote after an in-home visit. BC Wide provides that estimate free.

Should I pair a new furnace with a heat pump?

Many Richmond homeowners do, because our mild climate suits heat pumps for much of the year while the gas furnace covers the coldest, dampest stretches. It also adds cooling in summer. Whether it fits depends on panel capacity, outdoor unit placement and, in townhouses, strata approval.

Is BC Wide a factory-authorized dealer for furnace brands?

No. BC Wide is an independent TSBC-licensed HVAC contractor, and we install and service a range of furnace brands. We recommend equipment based on your home’s sizing, venting and space, not on a single manufacturer relationship.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote