★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Gas Boiler Replacement Cost in Delta (Ballpark)

Boilers

Gas Boiler Replacement Cost in Delta (Ballpark)
Home › Gas Boiler Replacement Cost in Delta (Ballpark)

Gas Boiler Replacement Cost in Delta (Ballpark)

Quick answer

In Delta, replacing a gas boiler with a new condensing gas boiler runs a ballpark of $7,000 to $15,000 installed, before GST, and a gas combi boiler that also heats your domestic hot water runs a ballpark of $8,000 to $14,000 and up. These are ballpark figures, not a quote. Where your home lands depends on venting, gas supply, the condition of the existing piping, condensate routing, access and permits, so an accurate price needs a site visit and a written quote from a licensed gas fitter.

Key takeaways

  • Ballpark for a condensing gas boiler replacement in Delta: $7,000 to $15,000 installed, before GST.
  • Ballpark for a gas combi boiler (heat plus domestic hot water): $8,000 to $14,000 and up.
  • Venting, condensate routing, gas line sizing, near-boiler piping and a proper system flush move the price more than the boiler itself.
  • Delta’s housing mix (North Delta split-levels, Ladner floodplain homes, Tsawwassen coastal exposure, strata townhouses) changes access, venting and approvals.
  • Gas work in BC requires a licensed gas fitter and a permit; only a site visit gives an accurate price.

In Delta, replacing an existing gas boiler with a new condensing gas boiler typically falls in a ballpark of $7,000 to $15,000 installed, before GST. These are ballpark figures for orientation only and are not a quote; an accurate price needs a site visit, because the house, not the boiler, decides most of the cost. If you want one appliance to handle both space heating and domestic hot water, a gas combi boiler installation sits in a ballpark of $8,000 to $14,000 and up. A straightforward swap in an accessible mechanical room with sound piping lands toward the lower end. A job that converts an old atmospheric boiler to condensing, needs new venting through a finished wall, a longer gas line, repiping and a full flush of sludge-laden radiant loops lands toward the upper end or beyond. The sections below explain exactly where your home is likely to sit and why.

How much does it cost to replace a gas boiler in Delta?

Most Delta boiler replacements fall inside two ballpark bands. A condensing gas boiler replacement for heating only runs roughly $7,000 to $15,000 installed. A gas combi boiler that also supplies domestic hot water runs roughly $8,000 to $14,000 and up, with the upper end reflecting homes that need a new gas line, extra piping or venting changes. Both bands are before GST, and both assume a licensed gas fitter, a permit, removal of the old unit and commissioning of the new one.

The spread is wide on purpose. Two houses on the same street in Sunshine Hills can come in thousands apart because one has a boiler in an open basement next to an exterior wall and the other has it tucked into a closet behind finished drywall with a masonry chimney that can no longer be used. If a new or longer gas line is required, add a ballpark of $500 to $1,500 for a short, accessible run, or $1,500 to $3,000 or more for a long or difficult one.

The table below shows where common Delta scenarios usually sit inside the range. It describes position, not price, because the dollar figure depends on the details a technician confirms on site.

ScenarioWhere it usually sits in the ballparkMain reason
Condensing boiler replaced with a new condensing boiler, same locationLower endVenting and condensate drain often reusable after inspection
Old atmospheric (chimney-vented) boiler replaced with a condensing boilerMiddle to upper endNew sealed venting, chimney abandonment or liner, new condensate drain
Heating boiler plus separate tank replaced with one combi boilerMiddle to upper end of the combi bandDomestic water piping changes, gas line capacity check
Boiler in a tight closet or crawlspace accessUpper endExtra labour for removal, carrying in and working space
Radiant floor system with heavy sludgeUpper endFlush, cleaning chemistry, filtration and possible valve replacement
Strata townhouse with new wall penetrationVaries, often upper endStrata approval, termination clearances, coordination

What pushes a boiler replacement price up or down?

The boiler is one line on the invoice. What moves the total is everything connected to it. When you compare quotes, look for how each of these was handled rather than just the bottom number.

  • Venting: a condensing boiler vents cool, acidic exhaust through sealed plastic or stainless piping, usually out a side wall. Replacing a chimney-vented boiler means new vent and combustion-air piping, new wall penetrations and correct clearances from windows, doors, decks and neighbouring buildings.
  • Condensate routing: condensing boilers produce acidic water that must be neutralized and drained. If there is no floor drain or suitable drain nearby, a condensate pump and longer run add cost.
  • Gas line sizing: a modulating boiler, or a combi that also heats domestic water, may need more gas than the existing line was sized for. A gas fitter measures the run and total connected load before deciding whether the pipe stays or is upsized.
  • Near-boiler piping: modern boilers typically want primary-secondary piping, a low-loss header or a hydraulic separator so flow through the heat exchanger stays correct. Older systems frequently need this rebuilt.
  • System cleaning: flushing old loops, adding a dirt and magnetite separator and treating the water protects the new heat exchanger. Skipping this is a common cause of early failure.
  • Controls and accessories: outdoor reset sensor, zone valves or circulators, expansion tank, air separator, backflow and fill valve often get replaced at the same time.
  • Electrical: a dedicated circuit, service switch or relocated wiring may be needed and must be done to code.
  • Access and disposal: stairs, crawlspaces, narrow doorways and heavy cast-iron sections all add labour, as does proper removal of the old unit.
  • Permits and code upgrades: gas work needs a permit, and bringing clearances, supports, venting and bonding up to current code is part of a legal job. Permit fees are set by each municipality or Technical Safety BC.

How do Delta homes change the cost of a boiler replacement?

Delta is really three communities with different housing, and each affects a boiler job differently. North Delta, including Sunshine Hills and the neighbourhoods around Scott Road, has a large stock of 1960s to 1980s split-levels and basement-entry homes. Many were built with hydronic baseboard or in-floor systems and chimney-vented boilers in a basement utility room. Converting those to condensing usually means abandoning or lining the old chimney, a new side-wall vent and a new condensate drain.

Ladner sits on low, flat floodplain ground with a high water table. Fewer homes have full basements; mechanical equipment is often in a garage, a main-floor utility room or accessed from a crawlspace. Crawlspace access raises labour, and equipment should sit high enough to be protected from moisture. Tsawwassen homes near the water face salt air, which is hard on exterior vent terminations and outdoor metal components, so termination material and placement deserve attention.

Both Ladner and Tsawwassen also have a lot of strata townhouses. A new vent through an exterior wall in a strata usually needs written strata approval before work starts, and termination clearances to neighbouring units and walkways are tighter. Building that approval time into the schedule avoids surprises.

Water chemistry matters too. Metro Vancouver water is soft, so hydronic problems here are sludge and corrosion byproducts such as magnetite, not limescale. Older loops, especially early radiant tubing without an oxygen barrier, can carry a lot of black sludge that must be cleaned out before a new boiler is connected.

Should a Delta home choose a condensing heating boiler or a combi boiler?

A heating-only condensing boiler makes sense when you already have a domestic water heater in good condition, when hot water demand is high (several bathrooms used at once), or when you want an indirect storage tank heated by the boiler. It keeps space heating and domestic hot water flexible.

A combi boiler makes sense in townhouses, smaller homes and suites where floor space is tight and hot water demand is moderate. It removes a separate tank and a second gas appliance. The trade-off is that simultaneous showers are limited by the unit’s manufacturer-published output, so verify that for your model with the installer, and the gas line must be able to feed it at full demand.

Either way, a proper heat loss calculation should size the boiler. Many older Delta boilers are oversized, and a right-sized modulating boiler runs longer, steadier cycles. That is a design decision to make on site, not over the phone.

What should a written boiler replacement quote include?

A quote you can compare fairly spells out scope, not just a total. Ask for each of these in writing:

  • The boiler type and size, and how that size was determined (a heat loss calculation, not the old unit’s label).
  • Venting plan: material, route, termination location and what happens to the old chimney connection.
  • Condensate drain plan, including neutralizer and pump if needed.
  • Gas line: whether the existing pipe is confirmed adequate or will be upsized.
  • Near-boiler piping, pumps, expansion tank, air and dirt separation, and controls being replaced.
  • System flush and water treatment included or not.
  • Permit, removal and disposal of the old unit, and commissioning with combustion testing.
  • Warranty handling and registration, stated according to the manufacturer’s current terms.
  • What is excluded, such as drywall repair, electrical upgrades or strata approvals.

Why can’t anyone give an exact boiler price over the phone?

Because the variables that decide the price are only visible in the house. Nobody can see over the phone whether your chimney is shared with a water heater, how far the gas meter is from the mechanical room, whether the radiant loops are full of sludge, or whether the new vent can legally terminate on the wall you want.

A site visit lets a technician measure the gas run, check the venting route and clearances, look at the piping and water condition, confirm electrical, and ask how you use hot water. That is what turns a ballpark into a real, written number. Any figure given without that visit is a guess, and guesses in boiler work tend to grow once the old unit is disconnected.

What can a homeowner do, and when do you need a licensed technician?

Homeowners can safely do the preparation and observation. Clear space around the boiler and the path to it, note the model and age from the rating plate, write down which rooms are cold or slow to heat, check the pressure gauge reading, and gather strata bylaws if you live in a townhouse. You can also reset a thermostat or replace its batteries.

Everything involving gas, venting or the sealed hydronic system requires a licensed professional. In BC, disconnecting or connecting gas piping, installing venting, commissioning and combustion testing must be done by a licensed gas fitter under permit. Most electrical work must be done by a licensed electrician or under a permit. Draining and refilling a pressurized system, bleeding air from the boiler itself or adjusting relief and fill valves should also be left to a technician.

Call a licensed technician promptly if you smell gas, see scorching or soot near the boiler or vent, hear repeated lockouts, find water on the floor, or notice the pressure gauge climbing or falling repeatedly. Those are signs to stop and have the system checked rather than wait for a planned replacement.

How do I get a free in-home boiler estimate in Delta?

BC Wide Home Services is an independent, TSBC-licensed HVAC contractor based in Burnaby and serving North Delta, Ladner, Tsawwassen and the rest of Metro Vancouver since 1999 (licences LGA0090068 and CGA0028029). We service the major gas boiler brands and can help you choose between a heating-only condensing boiler and a combi based on your home and how you use hot water.

A free in-home estimate includes a look at venting, gas supply, piping, water condition and access, and ends with a written quote that shows scope line by line. Call (604) 473-9690 to book a visit.

Gas & carbon-monoxide safety: Gas boilers burn natural gas and can produce carbon monoxide, an odourless, invisible gas, if venting is blocked, disconnected or corroded, or if combustion is poorly adjusted. Every home with a gas appliance should have working CO alarms near sleeping areas and on each level. If you smell gas, leave the house immediately without operating switches or appliances, then call FortisBC’s emergency line and 911 from outside. If a CO alarm sounds or anyone has headaches, dizziness or nausea that improves outdoors, get everyone out and call 911. Never try to repair gas piping, venting or burner components yourself; that work legally requires a licensed gas fitter in BC.

Frequently asked questions

What is the ballpark cost to replace a gas boiler in Delta?

A condensing gas boiler replacement in Delta runs a ballpark of $7,000 to $15,000 installed, before GST. A gas combi boiler runs roughly $8,000 to $14,000 and up. These are orientation figures only, not a quote, and your actual price depends on venting, gas line, piping and access confirmed on a site visit.

Why is a condensing conversion more expensive than a like-for-like swap?

An old chimney-vented boiler cannot share its venting with a condensing boiler. The job needs new sealed vent and air piping, a new wall termination, a condensate drain with neutralizer and often rebuilt near-boiler piping. When a condensing boiler is replaced with another condensing boiler, some of that can often be reused after inspection.

Do I need a permit to replace a boiler in Delta?

Yes. Replacing a gas boiler is regulated gas work in BC and needs a permit pulled by a licensed gas fitter. Permit fees are set by the municipality or Technical Safety BC, and a proper quote should state whether the permit is included.

Does soft water in Delta affect my boiler?

Yes, but not the way people expect. Metro Vancouver water is soft, so limescale is rarely the issue; sludge and corrosion byproducts like magnetite are. A good replacement includes flushing the system and adding dirt and magnetite separation to protect the new heat exchanger.

Can I replace my boiler in a Ladner or Tsawwassen townhouse?

Usually yes, but a new vent through an exterior wall normally needs written strata approval first. Termination clearances to neighbouring units, windows and walkways are tighter in attached housing. Starting the strata request early keeps the schedule on track.

How long does a boiler replacement take?

A straightforward swap is commonly completed in one to two working days. Conversions that need new venting, gas line work, piping changes or a heavy system flush can take longer. The site visit is where a realistic timeline gets set.

Is an estimate from BC Wide free?

Yes. The in-home estimate is free and ends with a written, line-by-line quote. Call (604) 473-9690 to book a visit anywhere in North Delta, Ladner or Tsawwassen.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

Gas Boiler Replacement Cost Delta: what we check first

Before anyone can price a boiler swap honestly, the installer has to look at the same handful of things in every house. The boiler itself is usually the smaller decision. The work around it is what spreads a job from the low end of the ballpark to the high end, and sometimes past it. The table below restates the ballpark ranges for the boiler jobs we quote most often in Delta, installed and before GST, with what tends to push each one higher. These are ballpark figures for orientation only, not a quote.

On the site visit, these are the checks that decide the number on your written quote:

  • Venting: where the old boiler vents today, often into a chimney or masonry flue, and where a condensing boiler’s sealed plastic vent can legally terminate, with clearances from windows, doors, property lines and a neighbour’s openings.
  • Gas supply: whether the existing pipe and meter can carry the new boiler’s input together with your other gas appliances. We measure and calculate this; we do not guess.
  • System water: the colour and condition of water drawn from a drain valve. Sludge and corrosion debris decide whether a chemical flush, a dirt separator or a magnetic filter goes on the quote.
  • Near-boiler piping: whether the old piping can be reused, and whether the new boiler needs primary-secondary piping or a hydraulic separator so it does not short-cycle.
  • Condensate: where the slightly acidic condensate can drain, by gravity or by a pump, and space for a neutralizer.
  • Electrical and controls: a proper circuit and service switch, a location for the outdoor reset sensor, and whether your thermostats and zone controls will talk to the new boiler. Electrical connections are licensed work.
Job in a Delta homeBallpark installed range, before GSTWhat usually pushes it higher
Condensing gas boiler replacing an existing gas boiler$7,000 to $15,000New vent route, condensate drain and neutralizer, repiping, a full sludge flush
Gas combi boiler for space heat plus domestic hot water$8,000 to $14,000 and upRemoving an old tank, new hot water piping, a larger gas supply
New gas line for the boiler, short and accessible run$500 to $1,500Meter capacity, opening finished ceilings
New gas line for the boiler, long or difficult run$1,500 to $3,000 and upDistance, finished basements, exterior routing
Replacing a separate atmospheric gas tank water heater at the same visit$1,800 to $3,000Venting changes, relocation, code upgrades on the old installation

Repair or replace a gas boiler in Delta: how the cost logic works

Repair or replace comes down to one question: is the money going into a part, or into a boiler near the end of its useful life? Answer it with a diagnosis, not a guess. Diagnostic service calls are $189.00. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived, taken off the installation. If the boiler still runs and you already know you want a new one, book the in-home replacement estimate instead, which is free.

If anyone smells gas, leave the house without touching light switches or appliances and call 911 and your gas utility from outside. If the carbon monoxide alarm sounds, get everyone outside first and do not restart the boiler until a licensed gas fitter has checked it.

Most replacement calls start with a problem, not a plan. These are the things Delta owners tell us on the phone, in their own words, followed by how we weigh repair against replacement:

  • The radiators or the floors take forever to warm up, or one part of the house never does.
  • The boiler keeps locking out and I have to reset it to get heat back.
  • There is banging, kettling or gurgling in the pipes.
  • There is water on the floor under the boiler, or a stain on the ceiling below it.
  • The pressure gauge keeps dropping and someone keeps having to refill the system.
  • The gas bill went up but the house is not any warmer.
  • There is soot near the vent, an exhaust smell, or the carbon monoxide alarm went off.
  • Diagnosis comes first: a licensed technician tests the boiler, its controls and its venting, then tells you whether the fault is a part or the boiler itself.
  • Repair usually wins when the heat exchanger is sound and one component has failed, such as an igniter, a flame sensor, a circulator pump or an expansion tank, on a boiler that otherwise runs cleanly.
  • Replacement usually wins when the heat exchanger is leaking or cracked, when parts for the model are no longer supported, when repairs keep stacking up season after season, or when the venting has to be rebuilt to current code anyway.
  • The honest test: add the repair to the repairs you can reasonably expect next, and ask whether that money is going into a boiler you would replace within a couple of heating seasons regardless. If it is, the replacement ballpark above is the better comparison.

How a gas boiler replacement visit works in Delta, step by step

A boiler replacement is planned work, so the order of steps matters more than speed. Here is how a job runs from first call to handover:

  • Step 1, the call: you phone (604) 473-9690 or email info@bcwide.ca. We ask roughly how old the boiler is, what it heats (radiators, in-floor loops or both), whether it also makes your hot water, and whether you live in a strata.
  • Step 2, the site visit: a licensed gas fitter looks at the venting route, gas meter and piping, system water, near-boiler piping, condensate path and controls, and takes measurements and photos.
  • Step 3, the written quote: you get the scope, the equipment tier, venting, gas and electrical work, the flush, the permit, disposal of the old boiler, warranty terms written out, and GST shown separately. No work starts before you have it in writing.
  • Step 4, the permit: we file the gas permit with Technical Safety BC. If you live in a strata, approval for any new wall penetration comes from your strata council, and the quote will say so.
  • Step 5, install day: gas is shut off, the system is drained, the old boiler comes out, and the new boiler is set, piped, vented, given its condensate drain and connected to gas and power.
  • Step 6, commissioning: the system is filled and purged of air, the burner is checked with a combustion analyzer, the outdoor reset curve is set for our mild coastal winters, and you are shown the controls and the normal pressure reading.
  • Step 7, inspection: the work is ready for inspection as the permit requires, and you keep the paperwork.
  • What a homeowner can safely do: clear a path to the boiler, note the symptoms and when they happen, read the pressure gauge, test your carbon monoxide alarms, and find any old manuals or permits.
  • What needs a licensed technician: anything on the gas piping, the vent, the burner or the controls inside the cabinet, and the electrical connections. In BC that work is legally restricted to licensed trades.
  • Gas and carbon monoxide safety: a boiler burns natural gas and makes carbon monoxide, an odourless gas. Keep a working CO alarm on every level and near sleeping areas, keep the vent termination clear of snow, leaves and storage, and never block the combustion air supply to the boiler room.

Gas boiler replacement in North Delta, Sunshine Hills, Scottsdale, Annieville, Ladner and Tsawwassen

Delta is not one housing market, and the same boiler can be a different job a few kilometres apart. We do not assume anything about a house until we have stood in its mechanical room, but these are the patterns we commonly plan around in each area.

North Delta and Annieville: many homes sit on sloped lots, and the boiler is often in a basement or lower-level utility room. On a slope, a side-wall vent can end up close to a neighbour’s window, a walkway or a deck above, and a gravity condensate drain is not always possible from a lower floor, which can add a condensate pump.

Sunshine Hills and Scottsdale: these are established neighbourhoods where a lot of homes have been renovated over the years. Renovations sometimes box a boiler into a tight closet or bury gas piping behind finished drywall, which affects access, the gas line cost and how much finishing has to be opened up.

Ladner: much of Ladner is low-lying, and some mechanical rooms sit at grade. We pay attention to how high the boiler and its controls sit off the floor, how reliable the condensate disposal is, and keeping vent terminations well above grade and away from where leaves and wind-driven rain collect.

Tsawwassen: coastal wind and salt air are hard on exterior metal. We look closely at the condition of outdoor gas piping, existing vent terminations and fasteners, and we place a new termination with the prevailing wind in mind so exhaust is not pushed back toward the house.

Strata townhouses anywhere in Delta: shared walls, strata bylaws on exterior penetrations and limited vent locations can decide whether a condensing boiler or a combi fits at all. Bring your strata’s rules to the estimate if you have them.

Which boiler brands do we service in Delta, and who does the work?

BC Wide Home Services Ltd is an independent TSBC-licensed contractor, not a factory-authorized dealer for any manufacturer, so we install and service several boiler brands rather than steering every house to one. Brands we service for gas heating boilers and gas combi boilers include IBC, Viessmann, Lochinvar, Navien, Rinnai and Bosch. We do not price by brand; the equipment on your quote is chosen to fit your home’s heat loss, piping and venting.

Here is what stands behind the quote:

  • TSBC contractor licence LGA0090068 and Class B gas licence CGA0028029.
  • Gas work done by licensed gas fitters, with permits filed and inspections arranged.
  • A written quote before any work begins, with warranty terms written on the quote rather than promised verbally.
  • 4.7 stars from 181 Google reviews.
  • Same-day where we can for a diagnostic visit; a full replacement is scheduled once the quote is accepted and the permit is in place.
  • Before you sign, check that the quote lists the scope, the equipment tier, venting, condensate, gas and electrical work, the flush, the permit, removal of the old boiler, written warranty terms, exclusions and GST. These are ballpark prices, not a quote. For exact pricing on your home, call BC Wide at (604) 473-9690 or email info@bcwide.ca.

More questions homeowners ask

How much does a new gas boiler cost in Delta BC?

A condensing gas boiler replacement in Delta runs a ballpark of $7,000 to $15,000 installed, before GST, and a gas combi boiler a ballpark of $8,000 to $14,000 and up. These are ballpark figures, not a quote. Venting, gas supply, piping condition and access decide where your home lands, so a site visit sets the real number.

Do you charge to come look at my boiler in Delta?

If your boiler is not working and needs to be diagnosed, that visit is a diagnostic service call at $189.00. The in-home estimate for replacing or installing a boiler is free. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation.

Should I repair or replace my old gas boiler?

Repair it when the heat exchanger is sound and one component has failed on a boiler that otherwise runs well. Replace it when the heat exchanger leaks, parts are no longer supported, repairs keep stacking up, or the venting needs rework anyway. A diagnosis first tells you which case you are in.

Do I need a permit to replace a gas boiler in Delta?

Yes. Replacing a gas boiler needs a gas permit through Technical Safety BC, filed by a licensed contractor, and the work is subject to inspection. Permit fees are set by Technical Safety BC or the municipality, not by us. In a strata, you also need strata approval for any new exterior penetration.

How long does a gas boiler replacement take in Delta?

A straightforward swap in an accessible mechanical room is commonly one to two working days on site. New venting through a finished wall, a new gas line, repiping or a heavy sludge flush adds time. The quote and the permit come first, so plan for those before the install day.

Can you replace a gas boiler same day in Delta?

Diagnostic visits are same-day where we can, and if the old boiler is unsafe it gets shut down and made safe. A full replacement is rarely a same-day job, because the right equipment, a written quote and a gas permit have to be in place first. We will tell you honestly what is and is not possible when you call.

Related BC Wide services

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote