★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Gas Boiler Replacement Cost in North Vancouver (Ballpark)

Boilers

Gas Boiler Replacement Cost in North Vancouver (Ballpark)
Home › Gas Boiler Replacement Cost in North Vancouver (Ballpark)

Gas Boiler Replacement Cost in North Vancouver (Ballpark)

Quick answer

A gas boiler replacement in North Vancouver usually costs a ballpark of $7,000 to $15,000 installed, before GST. These are ballpark figures for orientation only and are NOT a quote; an accurate price needs a site visit. A gas combi boiler that also makes domestic hot water tends to run $8,000 to $14,000 and up. Venting, gas supply, condensate routing, near-boiler piping and access on North Shore lots decide where your home lands. The in-home replacement estimate is free.

Key takeaways

  • Ballpark for a condensing gas boiler replacement in North Vancouver: $7,000 to $15,000 installed, before GST and before any rebate. This is orientation only, not a quote.
  • A gas combi boiler that also makes domestic hot water usually sits in a ballpark of $8,000 to $14,000 and up.
  • Venting changes, gas line sizing, condensate routing, near-boiler piping and system cleaning move the price more than the boiler itself.
  • Many North Shore homes have basement mechanical rooms, hillside access and decades-old hydronic loops, which add labour that a phone estimate cannot see.
  • Gas work in BC must be done by a licensed gas fitter under a permit; permit fees are set by Technical Safety BC or the municipality.
  • An accurate price needs a site visit: heat-loss check, venting route, gas supply and the condition of the existing system.

Replacing a gas boiler with a new condensing gas boiler in North Vancouver usually costs a ballpark of $7,000 to $15,000 installed, before GST and before any rebate. These are ballpark figures for orientation only and are NOT a quote; an accurate price needs a site visit, because the same boiler can cost very different amounts to install in a Lower Lonsdale strata unit, an Edgemont bungalow or a split-level on a steep Lynn Valley lot. A gas combi boiler that heats the home and makes domestic hot water tends to sit in a ballpark of $8,000 to $14,000 and up. Simple like-for-like swaps with an easy vent route land near the lower end. Jobs that need a new vent path, a larger gas line, a chimney liner for an orphaned water heater, or a full clean of a sludged hydronic loop climb toward the upper end or past it. Below we explain exactly what moves the number, what a written quote should contain, and how to get a real price for your home.

How much does a gas boiler replacement cost in North Vancouver?

For most North Vancouver homes, a straightforward replacement of an older gas boiler with a high-efficiency condensing gas boiler falls in the ballpark of $7,000 to $15,000 installed, before GST. That range covers the boiler, standard venting, near-boiler piping, controls, labour, the gas permit and removal of the old unit. It is deliberately wide because the installation work around the boiler varies far more between homes than the equipment does.

If the new boiler will also supply your domestic hot water as a combi unit, expect a ballpark of $8,000 to $14,000 and up. If the job includes running a new or larger gas line, that portion alone is commonly $500 to $1,500 for a short, accessible run and $1,500 to $3,000 or more for a long or difficult one, such as a route through finished ceilings or across a full-height basement.

The table below shows where common North Shore scenarios tend to sit within those ranges. It is a guide to relative cost, not a price list.

ScenarioWhere it usually sits in the ballparkMain reason
Condensing boiler replacing a condensing boiler, same locationLower end of the rangeVenting, condensate drain and gas supply are already suitable
Atmospheric (chimney-vented) boiler replaced with a condensing boilerMiddle of the rangeNew sidewall or roof vent and a condensate drain are required
Old boiler shared a chimney with a gas water heaterMiddle to upper endThe orphaned water heater usually needs a chimney liner or its own vent solution
Switch to a combi boiler for heat and hot waterCombi ballpark, often upper halfHot water piping, larger gas demand and mixing valve work
Undersized gas line or distant meterAdds a gas line cost on topPipe must be upsized or rerouted to carry the new load
Sludged cast-iron radiator or old in-floor loopUpper endPower flush, dirt separator and water treatment add labour
Tight crawlspace, narrow stairs or hillside accessUpper end or aboveExtra labour and handling time for removal and delivery

What moves the price of a boiler replacement on the North Shore?

The boiler is only part of the bill. The larger swings come from the work needed to make a modern condensing boiler run safely and efficiently in your specific home.

  • Venting: older atmospheric boilers vent into a masonry chimney. A condensing boiler needs its own sealed vent, usually plastic pipe through a sidewall or roof, and the termination must meet clearances from windows, doors, property lines and neighbours. On a tight lot this can mean a longer or more complicated route.
  • Orphaned appliances: when the boiler leaves the chimney, a gas water heater still venting there may no longer draft properly on its own. A liner or a separate vent solution is often required by code.
  • Gas line sizing: the gas pipe must carry the total load of every appliance at once. Adding a combi boiler, or keeping a range, fireplace and water heater on the same line, can mean upsizing pipe back toward the meter.
  • Condensate routing: condensing boilers produce acidic condensate that needs a drain, often with a neutralizer. If there is no floor drain nearby, a condensate pump may be needed.
  • Near-boiler piping and controls: primary/secondary piping, a new circulator, zone valves or a mixing valve for radiant floors, an outdoor reset sensor and new thermostats all add parts and labour.
  • System cleaning: Metro Vancouver water is soft, so the problem in old hydronic loops is sludge and corrosion debris, not limescale. Modern heat exchangers have narrow passages, so a flush and a dirt or magnetic separator are often recommended.
  • Electrical: a dedicated circuit, a service switch and a condensate pump outlet may be needed. That work belongs to a licensed electrician.
  • Permits and inspection: a gas permit is required. Permit fees are set by Technical Safety BC or the municipality, and we do not quote them as a fixed figure.
  • Access and disposal: stairs, crawlspaces, parking and the weight of an old cast-iron boiler all affect removal time.

Why do North Vancouver homes cost more or less to retrofit?

North Vancouver is two separate municipalities, the City and the District, and the housing stock between Lower Lonsdale and the upper slopes of Lynn Valley, Edgemont, Upper Capilano and Deep Cove is very different. Many post-war and 1960s to 1970s homes on the North Shore were built with hot water radiators or baseboard hydronic loops and a basement boiler room, often reached by a narrow stair. Those loops can hold decades of sludge, and swapping a heavy cast-iron boiler out of a basement is real labour.

Hillside lots matter too. Steep driveways and limited street parking affect delivery, and homes cut into a slope may have the mechanical room on the downhill side where a sidewall vent termination has to respect clearances to a neighbour’s windows or a walkway below. Upper-elevation neighbourhoods also see colder nights and more snow than the waterfront, so the heat-loss calculation can point to a different boiler size than a home of the same floor area near the water.

In Lower and Central Lonsdale strata buildings and townhouses, the constraints are different: the strata council may need to approve new wall penetrations, exterior vent terminations and working hours, and access through shared corridors has to be planned. The mild, wet coastal climate also means condensing boilers spend much of the season at low return water temperatures, which is exactly where they condense and gain efficiency, so proper outdoor reset controls are worth including in the scope.

Is a combi boiler or a boiler with a separate water heater cheaper to install?

A combi boiler replaces both the heating boiler and the tank, so the upfront installed cost is usually higher than a heat-only boiler, but you remove a second appliance and free up floor space. A heat-only condensing boiler paired with an indirect tank, or keeping an existing gas tank water heater, can suit larger homes with several bathrooms that run showers at the same time.

The right choice depends on your hot water demand, how many fixtures run at once, gas supply capacity and where the appliances can physically go. If you are also weighing a tankless water heater separately, we service Bradford White and Rheem tankless families, and the same rule applies: gas line sizing and venting decide the installed cost, and any capacity figure must be verified against the manufacturer-published specification for the exact model.

What should a written boiler replacement quote include?

Two quotes that look far apart are often quoting different scopes. Ask for each item below in writing so you can compare fairly.

  • A heat-loss estimate or sizing rationale, not just the size of the old boiler.
  • The make and model of boiler proposed, with the manufacturer-published efficiency rating and warranty terms to be verified on the spec sheet.
  • The full venting plan: route, termination location and whether the chimney needs a liner for any remaining appliance.
  • Gas line work: whether the existing pipe is adequate or needs upsizing.
  • Condensate drain and neutralizer or pump.
  • Near-boiler piping, circulators, zoning, mixing valves and controls, including outdoor reset.
  • System flush, separator and water treatment.
  • Electrical scope and who performs it.
  • Gas permit, inspection, removal and disposal of the old boiler.
  • Labour warranty, GST and a clear statement of what is excluded.

What can a homeowner do, and what needs a licensed technician?

Homeowners can gather useful information before an estimate: photograph the boiler rating plate, the vent connection and the gas meter, note the age of the system, list which rooms heat unevenly, and check whether a gas water heater shares the chimney. You can also check the pressure gauge reading and note any drips or noises, without opening or adjusting anything.

Everything involving the gas supply, venting, combustion setup, the burner, or opening the boiler cabinet must be done by a licensed gas fitter in BC. Draining and refilling a hydronic system, bleeding radiators on an old loop with questionable valves, and electrical connections should also be left to licensed trades. BC Wide Home Services Ltd is an independent TSBC-licensed contractor (LGA0090068, CGA0028029), not a factory-authorized dealer for any brand.

When should you call a licensed technician instead of waiting?

  • You smell gas, or a carbon monoxide alarm sounds: leave the home first, then call FortisBC or 911 from outside.
  • The boiler repeatedly locks out, short cycles or will not hold pressure.
  • You see water under the boiler, rust on the heat exchanger or scorching around the burner area.
  • Radiators stay cold at the bottom or the system is noisy with kettling or banging.
  • The boiler is well into its later years and a repair quote is a large share of replacement cost.
  • You are renovating, finishing a basement or adding square footage that changes the heat load.

Why does only a site visit give a real boiler replacement price?

A phone number without a site visit is a guess. A technician needs to measure the gas supply, trace the vent route and clearances, look at the existing near-boiler piping, check the condition of the water in the loop, confirm electrical supply and see how the old boiler will come out of the building. On the North Shore, those details regularly decide whether a job sits at the lower end or the upper end of the ballpark.

Rebates and incentive programs for high-efficiency gas equipment change over time and have their own eligibility rules, so we confirm what currently applies during the estimate rather than promising a figure. Financing options can also be discussed at that visit.

To get an accurate, written price for your North Vancouver home, book a free in-home estimate with BC Wide Home Services Ltd. Call (604) 473-9690 and we will assess your boiler, venting and gas supply and walk you through the options.

Gas & carbon-monoxide safety: Gas boilers burn natural gas and produce carbon monoxide, an odourless gas that can be deadly. Keep working CO alarms on every level of the home and near sleeping areas, and never block the boiler’s air intake or vent termination with snow, plants or storage. If you smell gas or a CO alarm sounds, leave the home immediately, do not operate switches, and call FortisBC or 911 from outside. In BC, installation, venting, gas piping and burner work on a boiler must be done by a licensed gas fitter under a permit.

Frequently asked questions

How much does it cost to replace a gas boiler in North Vancouver?

A condensing gas boiler replacement typically falls in a ballpark of $7,000 to $15,000 installed, before GST and before any rebate. This is orientation only and not a quote. Venting, gas line sizing, condensate routing, system cleaning and access decide where your home lands, which is why a site visit is needed.

Is a combi boiler more expensive to install than a regular boiler?

Usually yes, with a ballpark of $8,000 to $14,000 and up for a combi installation. It replaces the separate water heater, so you remove a second appliance. Whether it suits your home depends on how many fixtures run at once and your gas supply capacity.

Why is my quote higher than the ballpark range?

Quotes above the range usually include extra scope such as a new vent route, a chimney liner for an orphaned water heater, a longer or larger gas line, a full system flush, or difficult access on a hillside lot. Ask for an itemized scope so you can see exactly what is driving the number.

Do I need a permit to replace a gas boiler in North Vancouver?

Yes. A gas permit is required and the work must be done by a licensed gas fitter and inspected. Permit fees are set by Technical Safety BC or the municipality, and your contractor should include pulling the permit in the written quote.

Does soft Vancouver water affect a boiler replacement?

It does, but not through limescale. In Metro Vancouver’s soft water, older hydronic loops collect sludge and corrosion debris, which can clog the narrow passages of a new condensing heat exchanger. That is why a flush, a dirt separator and water treatment are often part of the scope.

Are there rebates for a new high-efficiency gas boiler?

Programs for high-efficiency gas heating equipment exist from time to time, but amounts and eligibility change. We check what currently applies to your home during the estimate rather than quoting a figure in advance.

How long does a boiler replacement take?

A like-for-like replacement is often completed in one to two working days. Jobs with new venting, gas line upsizing, a system flush or strata coordination can take longer, and the permit inspection is scheduled after the installation.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

Gas Boiler Replacement Cost North Vancouver: what we check first

Before anyone talks numbers, we look at five things in the mechanical room: how the old boiler is vented, the size and route of the gas line feeding it, where condensate can drain, the state of the near-boiler piping and the water in the loop, and how hard it will be to get the old unit out and the new one in. Those five checks explain most of the gap between the low and high ends of the ranges below.

Two homes with the same boiler on the quote can land thousands apart. A boiler that goes into the same spot, vents a short distance through a sidewall and already has a gas line sized for it sits near the bottom of the range. A unit going into a low basement on a stepped lot, needing a new vent path away from a neighbour’s window and a loop full of sludge that has to be cleaned out, sits near the top of the range or above it.

  • These are ballpark figures, not a quote, and they assume a gas boiler is replacing a gas boiler.
  • Any rebate or incentive you qualify for is handled separately and is not built into the ranges.
  • Permit fees are set by Technical Safety BC or the municipality and are listed on the quote as their own line.
JobBallpark installed range (before GST)What usually pushes it toward the high end
Condensing gas boiler replacing an older gas boiler$7,000 to $15,000New venting route, near-boiler piping rework, system flush, tight or stepped access
Gas combi boiler (space heat plus domestic hot water)$8,000 to $14,000 and upHot water piping changes, gas line upsizing, condensate routing
New or upsized gas line to the boiler, short and accessible run$500 to $1,500Finished ceilings, extra fittings, meter location
New or upsized gas line, long or difficult run$1,500 to $3,000 and upLong runs through finished space, exterior routing, several appliances on one line

Repair or replace your North Vancouver gas boiler? How the cost logic works

Most boilers we are called to do not need replacing. A failed igniter, a weak circulator, a stuck zone valve or a dirty flame sensor is a repair, and replacing a whole boiler over one of those is money spent in the wrong place. Diagnostic service calls are $189.00. That visit tells you what actually failed, what the repair involves and whether the rest of the boiler is worth keeping.

Here is what owners usually tell us when a replacement conversation is coming:

  • The boiler keeps locking out and someone has been out more than once this heating season.
  • There is rust or water under the boiler, or the pressure gauge keeps dropping and the system needs topping up.
  • Some rooms never get warm and the radiators or floors upstairs stay cool.
  • It bangs, kettles or gurgles when it fires.
  • The repair needs a part that is hard to find for a boiler this age.
  • A technician said the heat exchanger is leaking.
  • Gas bills climb every winter even though nothing has changed in how the house is heated.

When does repairing an old boiler stop making sense on the North Shore?

A useful rule: if the problem is a single component on a boiler with a sound heat exchanger and reasonably clean water, repair it. If the heat exchanger is leaking, the boiler is an older non-condensing design with recurring faults, or repair bills keep stacking up season after season, the money is usually better put toward a replacement. We tell you which side of that line your boiler is on, in writing, and you decide.

If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation. The only free service we offer is the in-home estimate for replacing or installing equipment; repairs, diagnostics and maintenance are billed.

One more piece of the logic: a new condensing boiler only performs as designed when the water coming back to it is cool enough to condense and the loop is clean. If your radiators or baseboard need high water temperatures to keep the house warm, we say so at the estimate and explain how controls and outdoor reset settings affect running cost, rather than promising savings we cannot measure in advance.

How a gas boiler replacement visit works in North Vancouver, step by step

What a homeowner can safely do: read the pressure gauge, note any error lights or codes, keep the area around the boiler clear, and check thermostat batteries and settings. Everything that touches gas, venting, the burner, wiring inside the boiler or the sealed water system is licensed work in BC and stays with the technician.

  • First contact: you call (604) 473-9690 or email. We ask what boiler you have now, how the home is heated (radiators, baseboard convectors or in-floor), whether hot water comes from the boiler or a separate tank, and whether it is a house or a strata unit.
  • In-home estimate: the replacement estimate is free. A licensed technician looks at the boiler, the vent, the gas meter and line, the expansion tank, the circulators and zone controls, and where condensate can drain.
  • Sizing: we size the new boiler to the home’s heat loss, not to the old nameplate. Older boilers were often oversized, and a right-sized boiler cycles on and off less.
  • Written quote: you get the scope, the equipment, the venting and gas work, the permit, removal of the old unit and the warranty terms written on the quote.
  • Permit and booking: we pull the gas permit and book the install day. Strata buildings may also need council or property manager approval for exterior vent changes.
  • Install day: a licensed gas fitter shuts off and caps the gas, the old boiler is drained and removed, the new boiler is mounted, the vent and condensate drain are installed, near-boiler piping and any loop cleaning are done, and the gas connection is leak-tested and combustion checked.
  • Startup and handover: we fill and purge the loop, set the controls, show you the thermostat and pressure gauge, leave the paperwork and book the permit inspection where required.

Gas boiler replacement in North Vancouver neighbourhoods: Lonsdale to Deep Cove

North Vancouver is two municipalities, the City and the District, and the boiler job changes with the housing more than the postal code. What follows is what we commonly run into; every house is different, so treat it as a guide, not a rule.

  • Lonsdale: plenty of strata buildings and townhomes. Venting through an exterior wall, strata approval for changes and moving equipment through hallways and elevators often decide the cost and the schedule.
  • Upper Lonsdale and Queensbury: many older detached homes, some still running hot-water radiator systems. Sound cast-iron radiators usually stay; the work is in the near-boiler piping and cleaning the loop.
  • Lynn Valley: a mix of older houses and newer infill, often on sloped lots. Basement mechanical rooms down stairs, and vent routes that must clear windows and property lines in narrow side yards, come up often.
  • Edgemont and Capilano: established detached homes, many renovated more than once. We often find piping added in stages over the years, which is worth tidying while the boiler is out.
  • Blueridge and Seymour: largely detached family homes, some with in-floor heat in an addition and baseboard or radiators elsewhere, which affects zoning, mixing and controls.
  • Deep Cove: steep driveways, stairs and longer travel mean access and carrying equipment in and out add labour. Damp, salty air is hard on exterior vent terminations and exposed metal.

Gas boiler replacement near me in North Vancouver: who does it, safety and next steps

BC Wide Home Services Ltd is an independent TSBC-licensed contractor based in Burnaby, serving Metro Vancouver since 1999, under licence LGA0090068 and Class B gas licence CGA0028029. Gas work is done by licensed gas fitters, under a permit, with the inspection booked where required. We are rated 4.7 stars from 181 Google reviews. Brands we service for gas boilers and combi boilers include Navien, Rinnai and Bosch; we are not a factory-authorized dealer for any of them, so the recommendation follows your venting, hot water demand, piping and local parts availability.

Gas and carbon monoxide safety comes first. If you smell gas, leave the home without operating switches and call your gas utility’s emergency line or 911 from outside. Keep working carbon monoxide alarms near sleeping areas and near the mechanical room. A boiler that soots, shows a yellow lazy flame or leaves the room stuffy should be turned off at the thermostat and inspected by a licensed technician; never adjust the burner, gas valve or vent yourself.

On timing: when a boiler fails outright in a cold snap, we come out same-day where we can, and a repair can often get heat back while the replacement is planned. A full replacement needs the right equipment on hand, a permit and a planned install day, so it is scheduled properly rather than rushed.

If you are comparing quotes, line them up item by item: boiler and size, venting, gas line work, condensate, loop cleaning, controls, permit, removal and warranty terms. A lower number that leaves out venting or cleaning is not the same job.

These are ballpark prices, not a quote. For exact pricing on your home, call BC Wide at (604) 473-9690 or email info@bcwide.ca.

More questions homeowners ask

How much does it cost to replace a gas boiler in North Vancouver?

A ballpark of $7,000 to $15,000 installed before GST for a condensing gas boiler, and $8,000 to $14,000 and up for a gas combi boiler. These ranges are for orientation and are not a quote. Venting, gas supply, condensate, piping and access decide where your home lands, which is why we price after a site visit.

Do you charge to diagnose a boiler in North Vancouver?

Yes. Diagnostic service calls are $189.00. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation.

Is a boiler replacement estimate free?

Yes, the in-home estimate for replacing or installing a boiler is free. That is the only free service we offer; repairs, diagnostics and maintenance are billed. The estimate comes as a written quote listing scope, permit, removal and warranty terms.

Do I need a permit to replace a gas boiler in North Vancouver?

Yes. Replacing a gas boiler is gas work that needs a permit and must be done by a licensed gas fitter in BC. Permit fees are set by Technical Safety BC or the municipality. We pull the permit and list it on the quote.

Can you replace my boiler the same day it breaks?

We come out same-day where we can to diagnose it, and a repair often gets heat back quickly. A full replacement usually needs equipment on hand, a permit and a planned install day. We tell you honestly which applies once we have seen the boiler.

Should I replace my old boiler with a combi boiler in North Vancouver?

Only if your hot water demand suits it. A combi works well for many smaller homes and strata units where one or two showers run at a time. A larger home with several bathrooms in use together is often better served by a boiler with a separate hot water tank, and we price both options at the estimate.

Related BC Wide services

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote