★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Gas Furnace Installation in Delta

Furnace

Gas Furnace Installation in Delta
Home › Gas Furnace Installation in Delta

Gas Furnace Installation in Delta

Quick answer

Gas furnace installation in Delta is licensed gas work. It starts with a heat loss calculation and a check of venting, gas line size, condensate routing and ductwork. It ends with a permit, an inspection and commissioning readings that you keep. A like-for-like replacement in an accessible Delta basement is usually done in one working day. Relocating the furnace, running new venting or upgrading the gas line adds time. BC Wide is a TSBC-licensed independent contractor, and every job gets a written quote that lists the scope, the permit and the warranty terms before work starts.

Key takeaways

  • A proper gas furnace installation in Delta starts with a room-by-room heat loss calculation, not the size of the old furnace.
  • Venting is usually the deciding factor: a high-efficiency condensing furnace needs plastic venting and a condensate drain, which older chimneys cannot provide.
  • Gas piping, venting, the gas permit and the final gas connection must be done by a licensed gas fitter; homeowners can clear access, change filters and set the thermostat.
  • Ladner and low-lying parts of Delta often have crawlspaces and higher moisture, which affects furnace location, condensate routing and duct sealing.
  • A finished job should leave you with a permit record, combustion and gas pressure readings, temperature rise, static pressure and the manufacturer’s registration details.

Installing a gas furnace in Delta means removing the old appliance safely, confirming the new furnace is sized to your home’s actual heat loss, running correct venting and gas piping, connecting it to your existing or modified ductwork, and commissioning it under a gas permit so it burns cleanly and moves the right amount of air. In most Delta homes the real decisions are not about the furnace box itself; they are about where it sits, how it vents, whether the gas line is large enough, and how well the ducts can deliver heat to every room. A licensed gas fitter must do the gas and venting work, and a correct installation ends with measured readings on paper, not just a warm house.

What does a gas furnace installation actually involve?

A furnace replacement looks simple from the outside: one cabinet out, one cabinet in. In practice it is several trades’ worth of work compressed into one or two days. The installer shuts off and isolates the gas, disconnects power, removes the old unit and its venting, and inspects what is left behind: the plenum, the return air path, the gas line, the vent route and the electrical supply.

The new furnace is then set on a level base, the supply and return plenums are fabricated or adapted to fit, and the gas line is connected with a proper shutoff valve and sediment trap. For a condensing furnace, plastic vent and combustion-air piping is run to an approved termination point outside, and a condensate drain is routed to a floor drain or a condensate pump. Finally the thermostat is wired, the system is started, and the technician measures gas pressure, combustion, temperature rise and airflow before handing it over.

  • Load calculation and equipment selection
  • Safe removal of the old furnace and abandoned venting
  • Plenum, transition and return-air work
  • Gas piping, shutoff valve and sediment trap
  • Venting and combustion-air piping to code clearances
  • Condensate drain and, where needed, a condensate pump
  • Thermostat wiring, start-up and commissioning under permit

How is the right furnace size chosen for a Delta home?

The most common installation mistake is copying the size printed on the old furnace. Many Delta homes were built in the 1960s, 70s and 80s and have since gained new windows, added insulation or a finished basement. A furnace that was right at the time may now be oversized, and an oversized furnace short-cycles: it heats the air quickly, shuts off, and repeats, which wears parts, creates uneven rooms and wastes gas.

A proper heat loss calculation looks at wall and ceiling insulation, window area and orientation, air leakage, foundation type and the design outdoor temperature for our area. Delta’s climate is mild and wet, so the design load is modest compared with the interior of the province, and many homes need less capacity than people assume. A two-stage or modulating furnace suits this climate well because it spends most of the heating season running at a low, steady output instead of cycling at full fire.

The furnace’s blower also has to match the ductwork. A unit that is correct on paper can still be noisy or ineffective if the existing ducts cannot carry the airflow it needs, which is why a good installer measures the ducts before choosing the model.

What housing in Delta changes the installation approach?

Delta is really three communities with different building stock, and each one tends to raise its own installation questions.

North Delta has many split-level and basement-entry homes from the 1960s through the 1980s. These often have the furnace in a basement utility room with an older masonry chimney or a metal B-vent that was shared with a gas water heater. Moving to a condensing furnace can orphan that water heater on a chimney that is now too large for it, which is a venting safety issue that must be addressed in the same job.

Ladner sits on low, flat ground near the Fraser River, and a good share of its homes have crawlspaces or slab-on-grade construction rather than full basements. Furnaces here are often in crawlspaces, garages or closets. Crawlspace installs need attention to moisture, clearances, service access and where the condensate goes, since there may be no floor drain nearby.

Tsawwassen has a mix of older ranchers and newer larger homes, some with attic or garage furnace locations and long duct runs. Salt air near the water is harder on outdoor vent terminations and on the outdoor section of any heat pump paired with the furnace, so termination location and materials deserve a second look.

Delta areaTypical housingInstallation factor to check
North Delta1960s to 1980s split-levels and basement-entry homesShared chimney with a gas water heater; orphaned water heater venting after a condensing upgrade
LadnerCrawlspace and slab-on-grade homes on low, flat groundMoisture, service access, condensate routing and condensate pump placement
TsawwassenOlder ranchers plus newer, larger homesLong duct runs, attic or garage locations, vent termination exposure to salt air
Townhouses and strata complexesCloset furnaces and shared wallsVent termination clearances to neighbours’ windows and strata approval requirements

Why is venting usually the deciding factor?

Venting decides which furnace a house can accept. A mid-efficiency furnace sends hot flue gases up a metal vent or lined chimney. A high-efficiency condensing furnace extracts so much heat that its flue gases are cool and wet, so it vents through sealed plastic pipe, usually out a side wall, and produces acidic condensate that has to be drained away.

That plastic vent has to reach the outside within the manufacturer’s maximum length and number of elbows, and the termination has to meet code clearances from windows, doors, air intakes, property lines, gas meters and grade. In a North Delta basement that is usually straightforward. In a Ladner crawlspace or a townhouse closet, finding a legal termination point can shape the whole job. Maximum vent lengths and pipe sizes are manufacturer-published, so verify them for your specific model with the installer.

When the old furnace leaves a shared chimney, the remaining gas water heater may no longer draft properly on its own. The fix may be a chimney liner, a resized vent or a change to the water heater, and it should be decided before installation day, not discovered afterward.

Does the gas line need to be upgraded for a new furnace?

Sometimes. Gas pipe is sized for the total load of every appliance on it and the length of the run from the meter. Homes in Delta that have added a gas range, fireplace, tankless water heater or barbecue line over the years may already be near the limit of their original piping. A licensed gas fitter checks the pipe size and length against the connected load and measures the gas pressure at the furnace with other appliances running.

If the line is undersized, the furnace can underfire, run inefficiently and cause ignition problems. Correcting it may mean replacing a section of pipe or running a new branch from the meter. This is licensed gas work only; homeowners should never alter, extend or reconnect gas piping.

What permits and inspections apply to a furnace install in Delta?

Replacing a gas furnace in BC requires a gas permit taken out by a licensed gas contractor before the work is done. Depending on the scope, electrical work may need its own permit. The permit creates an official record that the installation was done by a licensed trade and may be selected for inspection. Your installer should confirm which authority issues the permit for your address and file it in the contractor’s name, not yours.

Strata owners in Delta townhouse and apartment complexes should also check their bylaws. Many stratas require approval before a new vent penetration is made in an exterior wall, and some specify where terminations may go. Getting that approval early avoids delays.

Ask for the permit number at the end of the job and keep it with your home records. It matters for insurance, for resale and for your own peace of mind.

What does a correct installation look like when it is finished?

A good installation is quiet, tidy and documented. The furnace sits level with clear service space around it. Gas piping has a shutoff valve and sediment trap at the appliance. Vent pipes are sloped correctly back toward the furnace and supported along their length. The condensate drain has a trap and does not run uphill. The return air path is sealed so the furnace does not pull air from the utility room.

Most importantly, the technician should measure and record how the furnace is running, not just confirm it lights.

  • Gas permit number and the installing contractor’s licence details
  • Inlet and manifold gas pressure readings
  • Combustion analysis, including carbon monoxide in the flue gas
  • Temperature rise across the heat exchanger, within the range on the furnace rating plate
  • Total external static pressure, showing whether the ducts suit the blower
  • Blower and staging settings used, and thermostat configuration
  • Model and serial numbers, plus manufacturer warranty registration

What can a homeowner do, and when should you call a licensed technician?

Homeowners can prepare for installation by clearing a path to the furnace, moving stored items away from the utility area, and noting rooms that have always been too warm or too cold. After installation you can replace the air filter on schedule, keep the area around the furnace clear, keep outdoor vent terminations free of leaves and snow, and set your thermostat.

Everything involving gas piping, venting, burners, the heat exchanger, the control board or line-voltage wiring belongs to a licensed technician. Call one if you smell gas, if a carbon monoxide alarm sounds, if the furnace repeatedly starts and stops, if you see water pooling around the unit, if the vent terminal is frosting heavily or blocked, or if rooms that were comfortable before the change are now noticeably cooler.

If you are planning a replacement, a written quote should spell out the heat loss approach, the venting plan, any gas line or chimney work, and what documentation you will receive. The cost varies with location, venting and ductwork condition, so a site visit is the only way to get a reliable written figure. BC Wide Home Services is an independent TSBC-licensed contractor serving Delta since 1999; call (604) 473-9690 to arrange a visit.

Gas & carbon-monoxide safety: A gas furnace burns natural gas and produces carbon monoxide, a colourless, odourless gas that can be fatal. Every home with a gas furnace should have working carbon monoxide alarms near sleeping areas and on each level. If you smell gas, leave the house immediately without operating switches, then call your gas utility’s emergency line and a licensed gas fitter from outside. If a carbon monoxide alarm sounds or anyone has headaches, nausea or dizziness that ease when they leave the house, get everyone outside and call for help. In BC, gas piping, venting, appliance connection and repair are restricted to licensed gas fitters working under permit; never attempt them yourself.

Frequently asked questions

How long does a gas furnace installation take in Delta?

A straightforward replacement in a basement with an accessible vent route is often completed in one day. Jobs that need a new vent path, gas line changes, chimney work for an orphaned water heater or crawlspace access can take longer. Your installer should give you a realistic schedule after the site visit.

Can I keep my existing ductwork when I replace my furnace?

Usually yes, but it should be checked, not assumed. The installer measures static pressure and looks at duct sizing and leakage to confirm the new blower can move the air it needs. Undersized or leaky ducts can make a new furnace noisy and uneven, so some homes need return air or sealing improvements.

Is a condensing furnace always possible in an older North Delta home?

Most homes can accept one, but it depends on finding a legal side-wall or roof vent route and a place to drain condensate. If the old furnace shared a chimney with a gas water heater, that water heater’s venting must be corrected at the same time. A site visit confirms whether the route works.

Where does the condensate go in a Ladner crawlspace installation?

Condensate must drain to an approved location, which in a crawlspace without a floor drain usually means a condensate pump that lifts the water to a suitable drain. The line needs a trap and protection from freezing where it runs through cold areas. Routing it poorly is a common cause of water damage and nuisance shutdowns.

Do I need a permit to replace a gas furnace in Delta?

Yes. A gas permit is required and must be obtained by the licensed gas contractor doing the work, not by the homeowner. Ask for the permit number when the job is finished and keep it with your records for insurance and resale.

Can a new gas furnace be paired with a heat pump?

Yes. A heat pump can be added to handle heating in mild weather and cooling in summer, with the gas furnace taking over during colder periods. This suits Delta’s mild wet climate well, but it requires a compatible furnace blower, a suitable coil location and correct thermostat controls, so it is best planned at the time of furnace replacement.

How much does a gas furnace installation cost in Delta?

The cost depends on the furnace type, the venting route, the condition of the ductwork and whether gas piping or chimney work is needed, so it differs from home to home. The reliable way to know is a written quote after a site visit. Call (604) 473-9690 to book one.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

Gas Furnace Installation Delta: what do we check first on the site visit?

Before we quote a furnace in Delta, we look at the things that actually decide the job: where the venting can go, whether the gas line can carry the new load, where the condensate can drain, what the ductwork can move, and whether the electrical and clearances meet current code. We pick the furnace model last. If a quote names a model before anyone has checked those items, it is a guess.

We also ask plain questions. Which rooms stay cold? Does the furnace shut off and restart every few minutes? Does the house smell stale when the heat runs? Those answers often point to duct or venting problems that a new furnace on its own will not fix.

Gas and carbon monoxide safety comes first on every visit. If you smell gas, leave the house without touching switches, then call the gas utility’s emergency line or 911 once you are outside. If anyone in the home gets headaches, nausea or dizziness that ease when they go outside, treat it as possible carbon monoxide: get everyone out and do not go back in until the home has been cleared. Every home with a gas appliance needs working CO alarms near the sleeping areas.

  • Venting: the existing vent path, whether a water heater shares the chimney, and a legal exit point for plastic venting that keeps clear of windows, doors, decks, gas meters and property lines.
  • Gas supply: meter capacity, pipe size and run length to the furnace, and what else on the line can run at the same time, such as a water heater, range or fireplace.
  • Condensate: a floor drain or a condensate pump route, plus protection from cold if the line passes through a crawlspace or unheated garage.
  • Ductwork: return air size, static pressure, crushed or disconnected runs, and whether the supply plenum fits the new cabinet.
  • Electrical and controls: a dedicated furnace circuit with a service switch, the thermostat wiring, and whether a future heat pump would need extra conductors.
  • Access and clearances: the path to get the old unit out and the new one in, service room in front of the burner, and combustion air.

Should I repair or replace my gas furnace in Delta?

Most people call us because something has changed, not because of the year on the label. These are the signs we hear about most often, in the words homeowners use:

  • The furnace runs, but some rooms never warm up.
  • It turns on and off every few minutes.
  • There is a new bang, rumble or squeal when it starts.
  • The burner flame looks yellow and lazy instead of steady blue.
  • The gas bill went up even though nobody touched the thermostat.
  • There is water or rust around the bottom of the cabinet.
  • The same part has failed in two winters running.
  • A burning smell lasts well past the first few minutes of the heating season.
Situation we findWhat we usually recommendWhy
Single failed part, furnace otherwise soundRepairRestores safe operation without replacing a working system
Cracked heat exchangerReplace, and do not run the furnaceCombustion gases can reach the air you breathe
Repeated failures over a short periodReplaceMore repairs are likely and each one adds up
Parts discontinued or hard to sourcePlan a replacementOne more failure can leave the house without heat for days
Furnace works but rooms are unevenCheck the ducts firstA new furnace will not fix airflow problems in the ductwork

How does a gas furnace installation in Delta work, step by step?

A like-for-like replacement in an accessible basement, garage or utility room is usually finished in one working day. Moving the furnace, running a new side-wall venting route, upgrading the gas line or making major duct changes usually adds a second day. Adding a heat pump for a dual fuel system means outdoor work, a refrigerant line set and electrical work, so it is often booked over two to three days. The refrigerant work is done by a certified technician only.

As the homeowner, you can clear a path to the furnace, move stored items away from the work area, and make sure pets are kept away. All gas, venting, refrigerant and line-voltage electrical steps belong to licensed trades.

  • Step 1, the call: we ask about the current furnace, what it is doing and the layout of the home, then book an in-home estimate. If the house has no heat, we arrange a same-day visit where we can.
  • Step 2, the site assessment: measurements for the heat loss calculation, plus a look at the venting, gas line, condensate route, ductwork and electrical, with photos of the existing setup.
  • Step 3, the written quote: scope of work, equipment, venting and gas changes, the permit, disposal of the old furnace, and the warranty terms written on the quote.
  • Step 4, permit and scheduling: the licensed contractor takes out the gas permit before work starts, and the equipment is ordered and confirmed.
  • Step 5, installation day: the gas is shut off and capped, the old furnace is disconnected and removed, the new furnace is set and levelled, and plenum and return transitions are built. Venting and condensate are run, gas piping is connected and leak-tested, and the electrical and thermostat are connected.
  • Step 6, commissioning: gas pressure is set to the manufacturer’s specification, combustion is tested, temperature rise and static pressure are measured, the safeties are checked and the thermostat is set up.
  • Step 7, handover: we show you the filter and the thermostat, leave the commissioning readings with you, register the equipment with the manufacturer, and the gas inspection is completed or booked.

Gas furnace installation in North Delta, Ladner and Tsawwassen: what changes from house to house?

Delta is really three communities with different building patterns, and furnace work follows the housing. These are general patterns we plan for, not rules. Every house gets its own assessment.

  • North Delta, including Annieville and Scottsdale: many older detached homes and split-levels, with the furnace often in a basement or lower-level utility room. It is common to find the furnace and water heater sharing one chimney or metal vent. That matters when the furnace goes condensing, because the water heater can be left alone in a flue that is now too large for it.
  • Sunshine Hills: larger detached homes, many with additions or finished basements built after the original heating system went in. Ductwork that was extended rather than redesigned is common, so we look closely at return air and static pressure.
  • Ladner: low-lying ground, plenty of crawlspaces and higher moisture. Where the furnace goes, how condensate drains when there is no floor drain nearby, and how well the crawlspace ducts are sealed matter more here than in most of the region.
  • Tsawwassen: a mix of older detached homes, newer homes and townhouses, with salt air near the water. Vent terminations, and the outdoor unit of a dual fuel heat pump, should be placed and specified with corrosion in mind.
  • Newer subdivisions and townhomes across Delta: furnaces in tight closets or attics, shorter duct runs, and venting that may already be plastic. Strata homes usually need council or property manager approval for new wall penetrations or an outdoor unit before the job is booked.

How much does gas furnace installation cost in Delta?

The ranges below are ballpark installed prices for Greater Vancouver, before GST and before any rebate. A high-efficiency gas furnace replacement typically lands in a ballpark of $5,000 to $9,000, and complex jobs run higher. These are ballpark figures for orientation only and are NOT a quote. An accurate price needs a site visit.

Rebates to check: programs for high-efficiency gas furnaces and for adding a heat pump change often. Some need pre-approval, a registered contractor or a qualifying efficiency rating. Check current eligibility with your gas utility and the provincial program before you sign, and ask us to note any program requirements on the quote.

What moves the price on a Delta furnace job:

  • Venting: moving from a chimney to plastic side-wall or roof venting, the length of the run, and lining or resizing the chimney for a water heater that stays behind.
  • Gas line sizing: an undersized line, or a meter load that needs a new run.
  • Condensate routing: a pump and line where there is no floor drain close by, which is common in Ladner crawlspace homes.
  • Electrical: a dedicated circuit, a service switch and, for dual fuel, enough panel capacity.
  • Ductwork: new plenums, larger return air, and sealing crawlspace runs.
  • Permits and inspection: permit fees are set by Technical Safety BC or the municipality, and a correct quote includes them.
  • Access and disposal: tight closets, attics and stairs, plus removing the old furnace.
  • Code upgrades: bringing an older installation up to current code, including clearances, venting materials and CO alarm placement.
JobBallpark installed rangeWhat usually pushes it higher
High-efficiency gas furnace replacement$5,000 to $9,000Relocation, new venting route, duct rework
Adding a heat pump to a gas furnace (dual fuel)$10,000 to $18,000Panel upgrade when needed, long line set, outdoor unit placement
New gas line, short and accessible$500 to $1,500Finished ceilings, several appliances on one line
New gas line, long or difficult$1,500 to $3,000 and upLong runs, meter capacity, crawlspace or exterior routing

Who installs gas furnaces in Delta, and what should your written quote show?

BC Wide Home Services Ltd is an independent contractor licensed by Technical Safety BC (licence LGA0090068) and holds a Class B gas licence (CGA0028029). Licensed gas fitters do the gas piping, venting and final gas connection under a permit, and the work is inspected. We have served Metro Vancouver since 1999, and our Google rating is 4.7 stars from 181 reviews.

The gas furnace brands we service and install include Lennox, Carrier, Trane, Rheem, Goodman, Amana, York, Daikin, Bryant and American Standard. We are not a factory dealer for any of them. We choose equipment to suit the house, the venting and the parts support, and we will explain why a particular furnace fits your home.

Before any work starts, your written quote should spell out the exact scope: removal and disposal, venting changes, gas piping changes, the condensate route, duct transitions, electrical and the thermostat. It should say who takes out the gas permit and confirm that the job will be inspected. It should name the equipment make and model so you can look it up yourself. It should have the manufacturer warranty terms and our workmanship warranty terms written on it, and say who registers the equipment. It should list what is excluded, such as a panel upgrade or drywall repair, and what commissioning readings you will get at handover.

The in-home estimate for a furnace replacement or new installation is free, and the written quote is yours to compare. These are ballpark prices, not a quote. For exact pricing on your home, call BC Wide at (604) 473-9690 or email info@bcwide.ca.

More questions homeowners ask

How long does gas furnace installation take in Delta?

A like-for-like replacement in an accessible basement, garage or utility room is usually done in one working day. Moving the furnace, a new venting route, a gas line upgrade or adding a heat pump for dual fuel usually adds one or two days. The gas inspection may happen after the furnace is already running, depending on the inspector’s schedule.

Do I need a permit to install a gas furnace in Delta BC?

Yes. Replacing or installing a gas furnace needs a gas permit, and the licensed contractor doing the gas work takes it out before starting. The work is then inspected. Permit fees are set by Technical Safety BC or the municipality, and your written quote should show them as included.

Should I repair or replace my gas furnace?

Repair it when the fix makes it safe to run again and the furnace does not have a history of repeat failures. Replace it when the heat exchanger is cracked, parts are no longer made, or the same problems keep coming back. Diagnostic service calls are $189.00. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation.

Can I get a gas furnace installed near me in Delta the same day?

We get to no-heat calls same-day where we can, but a full installation normally needs a site assessment, a written quote, a permit and the equipment on hand first. If your furnace has failed and the house is cold, call and we will tell you honestly what can be done that day. We will not ask you to keep running a furnace we have found unsafe while you wait for the new one.

Can I add a heat pump when I replace my gas furnace in Delta?

Yes, and replacement is often the best time to do it. A dual fuel system pairs a heat pump with the new gas furnace: the heat pump handles mild, wet weather and summer cooling, and the furnace takes over in cold snaps. The furnace and indoor coil are chosen together, the electrical panel needs room for the outdoor unit, and only a certified technician handles the refrigerant.

Are there rebates for a new gas furnace or dual fuel system in Delta?

Sometimes. Programs for high-efficiency furnaces and heat pumps change during the year, and many need pre-approval, a registered contractor or a qualifying efficiency rating. Check current eligibility with your gas utility and the provincial program before you sign, and we will note any program requirements on the quote.

Related BC Wide services

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote