★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Getting Ready for Winter: A Homeowner’s Checklist

Furnace

Getting Ready for Winter: A Homeowner's Checklist
Home › Getting Ready for Winter: A Homeowner’s Checklist

Getting Ready for Winter: A Homeowner’s Checklist

Key takeaways

  • Start in early autumn, before the first cold snap, because that is when you still have a real choice about equipment, timing and scheduling.
  • Homeowners can change filters, clear vents and registers, test thermostats, test carbon monoxide alarms and clear the area around outdoor and vent terminations. Anything involving gas, combustion, refrigerant or the inside of the appliance cabinet is licensed work.
  • An aging furnace is not automatically an emergency. Age alone is a weak signal; repeat failures, rising noise, uneven heat and repairs to major components are stronger ones.
  • A cracked heat exchanger, a failed combustion test or any carbon monoxide concern is never something to defer to next season. That is the one item on this list with no wait-and-see option.
  • Carbon monoxide alarms belong on every level of the home, including outside sleeping areas, and they have an expiry date printed on the housing.
  • If you smell gas, leave the building first and call from outside. Do not troubleshoot it.

The short answer: in early autumn, run the heating system for a full cycle while the weather is still mild, replace the filter, test every carbon monoxide alarm, walk the house for blocked registers and blocked vent terminations outside, and book a licensed technician for a combustion and safety inspection before the first genuine cold spell. If the furnace is old and you are weighing replacement, this is also the window where you get to decide on your own terms rather than on the coldest night of the year. That last point is the real value of an autumn checklist. Nothing on it is dramatic. It is simply the difference between finding a problem in October, when you can think about it, and finding the same problem in January, when you cannot.

What should I actually do before the first cold snap?

Work through the list in order. The early items cost you nothing but attention, and they often surface the problem that matters before you have paid anyone to look for it. The point of running the system early is that a furnace which is going to fail usually tells you something on the first few cycles of the season: a longer start, a new rattle, a burning-dust smell that does not clear after the first cycle or two, a room that never comes up to temperature, a thermostat that calls for heat and gets nothing.

Do this on a mild day with the windows shut, and stay in the house while it runs. You are listening and feeling, not measuring. Let the system complete two or three full cycles so the blower, the ignition sequence and the safety controls all get exercised.

If everything behaves, you have lost an afternoon. If something does not, you have found it in the one part of the year when a Metro Vancouver homeowner still has options.

  • Run the heat for two or three full cycles on a mild day and listen to how it starts, runs and shuts down.
  • Replace the air filter, and note the size and the date somewhere you will find it again.
  • Test every carbon monoxide alarm and every smoke alarm, and check the expiry date printed on the alarm body.
  • Walk every room and confirm supply registers and cold-air returns are open and not blocked by furniture, rugs or curtains.
  • Check the thermostat: correct time and date, correct heating schedule, and fresh batteries if it uses them.
  • Go outside and clear leaves, soil, shrubs, bark mulch and stored items away from the vent and intake terminations and from any outdoor heat pump or air conditioning unit.
  • Clear the area around the furnace itself so the appliance has the clearance the manufacturer requires and nothing combustible is stored against it.
  • Look at the condensate drain and trap on a high-efficiency furnace for standing water, sediment or a kinked line.
  • Book a licensed technician for the combustion and safety inspection, and book it before the weather turns.
  • If the equipment is old, use this same window to get a proper written quote for replacement so the number exists before you need it.

Which jobs can I do myself, and which need a licensed technician?

In British Columbia, gas work and most electrical work are restricted to licensed trades, and refrigerant handling is restricted to certified technicians. That is not a liability disclaimer, it is the law, and the line is clearer than people expect. If a task requires opening the sealed combustion area, touching a gas connection, altering wiring, or adding to or recovering refrigerant, it is not a homeowner task under any circumstances.

Almost everything else on an autumn checklist is squarely yours. The table below splits the list the way a technician would.

TaskWho does itWhy
Replace the air filterHomeownerNo tools, no access to gas or wiring. A loaded filter starves the blower and is the single most common cause of poor airflow and short cycling.
Test carbon monoxide and smoke alarmsHomeownerPress the test button monthly and replace the whole alarm at the expiry date printed on it. Alarms age out whether or not they have ever sounded.
Open and unblock registers and returnsHomeownerClosing registers to save energy usually raises duct pressure instead and makes the rest of the house worse.
Clear vent and intake terminations outsideHomeownerBlocked combustion air intake or exhaust is a safety issue. Clear debris, snow, nests and plant growth from around the pipes but do not modify them.
Program or replace the thermostat batteriesHomeownerBattery-powered thermostats fail quietly. Swapping the thermostat itself is licensed work on most systems because of the control wiring and equipment compatibility.
Clean around the outdoor heat pump or air conditioning unitHomeownerKeep the coil face and the base clear of leaves and mulch. Do not open the cabinet and do not attempt to straighten fins or touch the refrigerant lines.
Inspect burners, flame sensor and ignition componentsLicensed technicianRequires opening the appliance and understanding the ignition sequence. Improper reassembly creates a combustion hazard.
Heat exchanger inspectionLicensed technicianA crack can be invisible from outside the cabinet and is identified through inspection and combustion testing, not by listening to the furnace.
Combustion analysis and venting checkLicensed technicianInstrument work. This is what actually confirms the appliance is burning and venting safely.
Any gas piping, gas connection or gas leakLicensed gas fitterRestricted work in BC. If you smell gas, leave the building and call from outside.
Refrigerant charge on a heat pump or air conditionerCertified technicianLegally restricted. A system low on refrigerant has a leak, and adding refrigerant without finding the leak is not a repair.
Hydronic system bleeding, sludge and circulator issuesLicensed technicianBoiler and hydronic work involves gas, pressurized water and controls together.

How do I tell whether my furnace is genuinely near the end?

Age is the weakest signal, even though it is the one everybody reaches for first. Equipment lifespan is a range, not a number, and where a particular furnace lands in that range depends on how well it was installed, whether the ductwork suits it, how often the filter was actually changed, and how hard it has been asked to work. A well-installed, well-maintained furnace in a house with adequate ducting can comfortably outrun a neglected one that is years younger. Anyone who tells you the appliance is finished because of the date on the label is skipping the part that matters.

The stronger signals are behavioural, and they tend to arrive together rather than one at a time. Watch for a pattern rather than a single bad day.

One more honest note: a single repair does not mean the end. Igniters, flame sensors, pressure switches and capacitors are ordinary wear items and replacing one is a normal part of owning gas equipment. It is the accumulation, and specifically the arrival of major-component repairs, that changes the arithmetic.

  • More than one unplanned service call in the last couple of heating seasons, for different faults each time.
  • A repair quoted on a major component such as the heat exchanger, the control board or the inducer motor, on equipment already well into its expected life.
  • New noise that was not there last year: a rattle at start-up, a rumble during firing, a squeal or grinding from the blower.
  • Rooms that never reach temperature any more, or a system that runs far longer than it used to for the same result.
  • Short cycling that persists after the filter is changed and the registers are opened.
  • Soot marks, a flame that is yellow and lazy rather than crisp and blue, or moisture or corrosion showing at the vent connection.
  • A combustion concern, a failed combustion test or a suspected cracked heat exchanger, which belongs in its own category entirely.

Should I replace it now, or get one more season out of it?

Sometimes one more season is genuinely the right call, and a page like this should say so plainly. If the furnace is old but starts cleanly, holds temperature, has passed a combustion and safety inspection this autumn, and has not needed unplanned repairs, then running it through another winter is a reasonable, defensible decision. Old is not the same as unsafe. What you are buying with that decision is time, and what you owe in return is attention: keep the filter fresh, keep the carbon monoxide alarms current, and treat any change in behaviour as information rather than background noise.

The decision changes when any of three things is true. First, if a technician identifies a combustion problem or a cracked heat exchanger, there is no wait-and-see option, and nothing else in this article outweighs that. Second, if a major component has failed on equipment already deep into its service life, you are choosing between a significant repair on old equipment and the same money moving toward something with a warranty behind it. Third, if the household simply cannot absorb a mid-winter failure, the calculus is different for you than for a neighbour who can.

What should not drive the decision is a calendar. Be sceptical of any argument built around the season rather than the equipment, and ask for the reasoning in writing. A good recommendation names the specific component, the specific test result and the specific risk. If it cannot do that, it is not a recommendation, it is pressure.

The honest argument for acting early is not about money and it is not about a promotion. It is about choice. A planned replacement means you select the equipment rather than taking what is on the truck; you pick a day that suits the household; you get a proper site assessment, with the gas line, the venting, the ductwork and the electrical all actually looked at instead of worked around; the permit is in hand; and nobody spends a week in a cold house or showering at a neighbour’s. In a cold snap, all of Metro Vancouver calls at once. Scheduling pressure in those weeks is real, and same-day work is not always possible for everyone who wants it. That is a fact about demand, not a sales tactic, and the fix is simply to make the decision when the weather is mild.

What should I check on the rest of the system, not just the furnace?

A furnace is rarely the only thing that winter tests. Work outward from the appliance and the list stays short.

Ductwork and airflow deserve more attention than they usually get, because most complaints that sound like a furnace problem are really a distribution problem. If one room is always cold, the fault is often a crushed flexible duct, a disconnected branch in a crawlspace, a closed damper or a return path that was never adequate. Those are worth diagnosing before you conclude the appliance is too small.

If you have a heat pump paired with a gas furnace, autumn is when you confirm the changeover behaves correctly, so the heat pump carries the mild weather and the furnace takes over in a cold snap the way it is supposed to. A controls problem here shows up as a system that either never runs the heat pump or never hands off, and it is easiest to catch before you need either one.

Gas fireplaces get switched on in October after sitting idle since March, and the pilot, glass gasket and venting all want a look before that first evening. Water heaters, tank or tankless, work harder in winter because the incoming water is colder. Tankless units in particular should have their filters and inlet screens checked and a descaling interval discussed with your installer; Metro Vancouver water is soft, so this is about heat-driven mineral deposits and debris rather than the heavy limescale you would fight in a hard-water region.

  • Look for cold rooms and trace them to the duct branch, not the thermostat.
  • Check that crawlspace and attic duct connections are still attached and still insulated.
  • On a dual fuel system, confirm the heat pump and the furnace hand off cleanly before the first cold weather.
  • Clear leaves and debris from around the outdoor unit and keep the base free of standing organic matter.
  • Have the gas fireplace looked at before its first real use of the season.
  • On a boiler or hydronic system, watch for cold radiators, air noise or a pressure reading that has drifted, and have sludge and circulator issues assessed by a licensed technician.
  • On a tankless water heater, check inlet screens and filters and ask your installer what descaling interval suits your unit and usage.

What does Metro Vancouver specifically change about this list?

Our winters are mild and wet rather than brutally cold, and that shapes the failure patterns here. Equipment spends most of the season running long, gentle cycles rather than fighting extreme temperatures, which is easy on the appliance but hard on anything exposed to moisture. Corrosion at vent terminations, rusted cabinet bases, condensate lines that have grown biological sludge and outdoor units sitting in wet bark mulch are all far more common here than in a dry cold climate. The autumn walk-around outside matters more in Burnaby than it would in a prairie city.

The cold snaps we do get are short, sharp and universal. When the temperature drops for a few days, the entire region’s heating equipment is asked for full output at the same time, and the marginal systems fail together. That is why an appliance can coast through years of mild winters and then quit in the one week everybody else’s is quitting too.

Our housing stock is mixed and old in places. Post-war houses across Vancouver, Burnaby and New Westminster often have gas lines and venting that were sized for whatever was installed decades ago, and ductwork that has been adapted more than once. When a replacement is planned properly, the gas line capacity, the vent routing and the duct sizing are all part of the assessment. When it is rushed on a cold night, they get worked around. That is the single best practical argument for deciding in autumn.

Strata and townhouse owners have an extra step, and it is worth doing early. Shared walls, shared chases and common-property venting mean the strata usually needs to approve the work, and that approval has its own pace. Permits are also part of a legitimate replacement in most municipalities here, pulled by the licensed contractor rather than by you. Water in Metro Vancouver is soft, which is good news for hydronic and tankless systems, but softness is why hydronic problems here present as sludge, corrosion and oxygen ingress rather than scale, and the fix is different for each.

When should I stop and call a licensed technician?

Some items on this list are worth a call now rather than a note for later. If you smell gas, stop reading and act: get everyone out of the building, leave the door open behind you, do not operate switches or your phone indoors, and call from outside. If a carbon monoxide alarm sounds, treat it as real, get out, and call from outside. Neither of those is a troubleshooting situation.

Short of that, a combustion concern is the one item on an autumn checklist with no wait-and-see version. A suspected cracked heat exchanger, a failed combustion test, persistent soot, a yellow rolling flame, or a vent connection showing corrosion and moisture are not things to carry through a winter. Everything else on this page can be weighed. That cannot.

The everyday reasons to call are less dramatic and just as useful: the system will not start, it starts and locks out, it runs constantly without reaching temperature, or it makes a noise it did not make last season. Same-day attendance is often possible outside a cold snap and harder during one, which is precisely why autumn is the cheap time in effort terms to get a look at things. We will tell you honestly when same-day is realistic and when it is not rather than promise an arrival window we cannot keep.

  • Gas smell: leave the building, call from outside, do not investigate.
  • Carbon monoxide alarm sounding: leave the building, call from outside.
  • Any suspected heat exchanger crack or combustion problem: do not run the appliance, call immediately.
  • Repeated lockouts, no ignition or a system that will not hold temperature.
  • Water where there should not be water: around the furnace base, the condensate trap, or a boiler.
  • A new noise, a new smell that does not clear, or visible soot.
  • Before any replacement decision, for a proper site assessment and a written quote you can read at your own pace.

What does a proper autumn inspection actually include?

It is worth knowing what you are buying so you can tell a real inspection from a quick look. On a gas furnace, a licensed technician should check the ignition sequence end to end, inspect the burners and the flame pattern, inspect the heat exchanger, verify the safety controls including the pressure switch and limit, examine the venting and the combustion air supply, check gas pressure, run a combustion analysis, inspect the blower and check airflow, check the condensate path on a high-efficiency unit, and verify the thermostat is controlling the equipment the way it should.

You should get a plain-language account of what was found, what is fine, what is worth watching and what needs attention now, with the distinction between those three made clearly. If something needs replacing, you should be told which component and why, in writing. Ask for that and read it before you agree to anything.

BC Wide Home Services Ltd has been doing this work across Metro Vancouver since 1999. We are an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029, not a factory-authorised dealer for any manufacturer, which means the brands we recommend are recommended because they suit your house and not because of an arrangement. If you want an autumn inspection booked, or a written quote on file before you actually need it, call (604) 473-9690.

Gas & carbon-monoxide safety: Gas appliances produce carbon monoxide, which has no colour, taste or smell. Install carbon monoxide alarms on every level of the home, including outside sleeping areas, test them at the start of the heating season, and replace the whole alarm at the expiry date printed on the housing. If an alarm sounds, or if anyone in the household has headaches, nausea, dizziness or flu-like symptoms that improve when they leave the house, get everyone outside and call from outside. If you smell gas, leave the building immediately without operating switches, appliances or your phone indoors, leave the door open behind you, and call from a safe distance. Do not attempt to find the leak yourself. A suspected cracked heat exchanger or any combustion concern must be assessed before the appliance is run again. In British Columbia, gas work and most electrical work are restricted to licensed trades, and refrigerant handling is restricted to certified technicians. Never attempt those yourself. BC Wide Home Services Ltd, TSBC licences LGA0090068 and CGA0028029, (604) 473-9690.

Frequently asked questions

When should I start my winter heating checklist in Metro Vancouver?

Early autumn, while the weather is still mild enough that you can go without heat for a day if something turns out to be wrong. That timing is the whole point: it gives you a real choice about equipment, scheduling and whether to repair or replace. Waiting until the first cold snap removes those choices, because that is when every heating system in the region is being asked for full output at once.

How often should I change my furnace filter?

It depends on the filter type, the thickness and what is in your air, so follow the manufacturer’s guidance for your specific filter rather than a general rule. Check it monthly during the heating season and replace it when it looks loaded rather than waiting for a date. Pets, renovations and a household that runs the fan continuously all shorten the interval considerably.

Is it safe to run an old furnace through one more winter?

It can be, if a licensed technician has inspected it this autumn, the combustion test passed, the heat exchanger is sound and it is starting and running normally. Age on its own does not make an appliance unsafe. What makes it unsafe is a combustion or heat exchanger problem, and that is exactly the thing an autumn inspection exists to find.

What are the signs a furnace is about to fail?

Look for a pattern rather than one bad day: repeated unplanned repairs for different faults, new noises at start-up or during the blower run, rooms that no longer reach temperature, short cycling that survives a filter change, and soot or a yellow lazy flame. Any of those is worth a diagnostic visit. A combustion concern or a suspected cracked heat exchanger is not a warning sign to monitor, it is a stop-now item.

Do I need a permit to replace a furnace in Metro Vancouver?

Gas appliance replacement generally requires a permit, and the licensed contractor pulls it rather than the homeowner. Requirements vary between municipalities in the region, so ask your contractor to confirm what applies at your address and to show you the permit. If you live in a strata, you will usually also need strata approval, and starting that process in autumn avoids having it become the bottleneck later.

Should I close vents in rooms I do not use to save energy?

Usually no. Closing registers raises static pressure in the duct system, which can reduce airflow across the heat exchanger, cause the furnace to cycle on its limit and make comfort worse everywhere else in the house. If a room genuinely does not need heat, raise it with your technician so the system can be balanced properly instead.

My heat pump runs in mild weather but the furnace never seems to take over. Should I worry?

On a dual fuel system the changeover is controlled, and a control or setpoint problem can leave the heat pump running when the furnace should have taken the load, or the reverse. Autumn is the right time to confirm the handoff works, because the failure is far easier to diagnose calmly than during the first cold spell. Have a licensed technician verify the changeover settings and the wiring.

Can I do anything about a cold room myself?

You can confirm the register is fully open and unobstructed, that furniture and rugs are clear of it, and that the return path from that room is not blocked by a closed door and no undercut. Beyond that, cold rooms are usually a duct problem, such as a crushed flexible run, a disconnected branch in a crawlspace or an undersized return, and those need someone who can get into the crawlspace or attic and trace the run.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.
Are BC Wide technicians licensed and insured?
Yes. BC Wide holds a TSBC gas-fitting licence, our technicians are Red Seal certified for HVAC and gas, and we carry full liability insurance and WorkSafeBC coverage.
How can I book a service call?
Call (604) 473-9690, email info@bcwide.ca, or use the booking form on bcwide.ca. Most calls are answered the same business day and we offer next-day appointments for non-emergency work.
Do you offer free estimates?
Yes. Free in-home estimates are provided for boiler, furnace, heat pump and water-heater replacements. Diagnostic visits for repairs carry a flat service fee that is credited toward the repair if you proceed.
What brands do you service?
We service all major brands including Viessmann, Navien, IBC, Rinnai, Rheem, Bradford White, Weil-McLain, Laars, Baxi, NTI, Lennox, Carrier, Bryant, Goodman, Trane, York, Daikin, Mitsubishi Electric, AO Smith, Bosch, Noritz, Giant, GSW, John Wood, and Valor.
Do you offer government rebates for heat pumps?
Yes. We are a registered contractor for BC Hydro, FortisBC and federal Greener Homes rebates. A high-efficiency heat pump installation can qualify for up to $11,000 in combined rebates depending on your home and income.
How quickly can you replace a broken hot water tank?
Standard 40 or 50-gallon gas or electric tanks are typically replaced same-day or next-day from stock. Tankless water heaters and larger commercial units usually take 1–3 business days depending on parts availability.
Why should I choose BC Wide over other HVAC companies?
BC Wide Heating & Air Conditioning has been operating in Greater Vancouver since 1999 as a TSBC-licensed (LGA90068) HVAC and gas contractor. We specialise in furnaces, boilers, heat pumps and water heaters across every major brand, we give honest options instead of upselling, and our work is performed by experienced, certified staff — not subcontractors.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote