- Getting a dual-fuel heat pump into a strata home is usually a paperwork problem before it is a mechanical one, and the paperwork moves fastest when a contractor has already looked at the property.
- The outdoor unit is the part that touches common property, so placement, mounting, noise and how refrigerant lines and the condensate route travel through the building are what a council actually decides on.
- Councils cannot approve a vague idea. They need a written scope with placement, a mounting method, an electrical plan, permit and licence details, insurance, and a sense of the work window.
- Ballpark installed cost for adding a heat pump to an existing gas furnace in Greater Vancouver runs $10,000 to $18,000 before GST, with an electrical panel upgrade extra when one is needed. That is a range for orientation, not a quote.
- Never assume what your building allows. Read your own bylaws and any alteration agreement, ask council or the property manager in writing, and keep every answer.
- BC Wide is an independent TSBC-licensed contractor (LGA0090068, CGA0028029), not a factory-authorised dealer, and gas and most electrical work is restricted to licensed trades in BC.
If you own a townhouse, duplex half or apartment in a Metro Vancouver strata and you want a heat pump added to the gas furnace you already have, the approval usually hinges on one thing: where the outdoor unit goes and what it touches on the way there. The indoor side is generally straightforward, because the heat pump coil sits on the furnace you already own and the ducts are already there. The outdoor condenser, its mounting pad or brackets, the refrigerant line set, the condensate route and the electrical feed are the parts that cross into common property or limited common property, and that is what a strata council is being asked to permit. The practical path is to get a contractor on site first, turn that site visit into a written scope your council can actually vote on, submit it through whatever alteration process your bylaws describe, and then schedule the work around the building’s access and shutdown realities. This page explains that sequence and what makes it stall.
Why does a dual-fuel heat pump need strata approval at all?
A dual-fuel system keeps your gas furnace and adds a heat pump that handles heating in mild weather, with the furnace taking over in a cold snap and for the coldest stretches. That pairing suits Metro Vancouver’s climate well, because most of our heating season sits in the temperature band where a heat pump works comfortably, and the gas furnace is still there for the handful of weeks when it does not.
The heat pump coil, the controls and the furnace itself are typically inside your unit and are typically yours. The outdoor condenser is not so tidy. It has to sit somewhere with air clearance on the sides and above, it has to be fastened to something, it needs a refrigerant line set and a control cable running back to the furnace, and it needs its own electrical circuit. Any of those can cross a wall, a slab, a balcony deck, a roof membrane, a fence line or a shared electrical room. Those are the elements most strata corporations treat as common property or limited common property, and that is the reason an alteration request exists.
Do not read this page as legal advice, and do not let anyone tell you what your building permits based on what another building permitted. Approval thresholds, notice requirements and who signs an alteration agreement vary from strata to strata. The reliable answer lives in your own registered bylaws, your strata plan and whatever council or your property manager tells you in writing.
What is usually in-suite and what is usually common property?
The table below is a general orientation only, not a statement about your building. Your strata plan and bylaws govern, and limited common property designations can move the line in either direction. Use it to frame the questions you ask council rather than as an answer.
| Component | Where it usually sits | Why council cares |
|---|---|---|
| Gas furnace and indoor coil | Generally inside the strata lot | Little visual or structural impact, but combustion and venting still require a licensed gas fitter and permitting |
| Thermostat and dual-fuel controls | Generally inside the strata lot | Usually the least contentious part of the whole project |
| Outdoor condenser | Usually on common or limited common property | Placement, sound, appearance, clearances and who maintains the area around it |
| Mounting pad, brackets or roof curb | Usually common property | Penetrations, membrane integrity, load and long-term responsibility for the fastening |
| Refrigerant line set and control cable | Often crosses common property | Wall penetrations, fire separations, sealing and the route’s visibility |
| Condensate routing from the furnace or coil | Often crosses common property | Where the water ends up and whether an existing drain can be shared |
| Electrical circuit and panel capacity | Panel may be in-suite or in a shared room | Available capacity, access to shared electrical rooms and who bears any upgrade |
| Existing gas service and venting | Shared service, in-suite appliance | Any change to gas piping or venting needs a licensed gas fitter and permitting |
What order do approvals, quotes and permits normally happen in?
Owners often try to get approval first and a quote second. That almost always backfires, because a council cannot approve a placement nobody has looked at and cannot assess noise or clearances from a brochure. The order that actually moves is: read your bylaws, ask council in writing what their alteration process is, get a contractor on site, turn the site visit into a written scope, submit that scope, then schedule the work and pull permits once you have a decision.
Ask council or your property manager two things early, in writing. First, what does their alteration request require, and is there a standard alteration agreement form. Second, is there a decision meeting schedule, because a council that meets monthly sets the real pace of your project. Knowing that a decision cannot land before a certain meeting changes how you plan the rest.
- Read your own registered bylaws and any rules on alterations, appearance and noise before you do anything else.
- Email council or the property manager and ask for the alteration process in writing, and keep the reply.
- Book a site visit so placement, line routing, panel capacity and access are assessed in person rather than guessed at.
- Get the written scope, with placement and mounting described plainly enough that a non-technical council member can picture it.
- Submit the alteration request with the scope, licence and insurance details attached.
- Once you have a written decision, book the work, confirm building access and arrange permitting through the licensed contractor.
- Keep the permit records, inspection paperwork and the approval correspondence with your unit’s file, because a future buyer’s conveyancer will ask.
What does a strata council actually need from a contractor before it can decide?
Councils are volunteers. They are not trying to obstruct you, but they cannot approve something they cannot picture, and they will not approve something that leaves an open question about who pays if a wall leaks in five years. A decision-ready package answers those worries in advance.
A good submission says exactly where the outdoor unit goes and how it is fastened, how the line set and condensate travel and where they penetrate, what electrical work is involved, who holds the licences, what the insurance position is, how long the crew needs the space, and what the site looks like when the crew leaves. Sound is worth addressing directly rather than waiting for someone to raise it, since in dense Metro Vancouver buildings the nearest bedroom window is often the real constraint on placement.
- A plain-language scope of work naming the equipment type and the dual-fuel arrangement, without asking council to interpret technical specifications.
- Proposed outdoor unit location with clearances shown, plus a photo or simple sketch of the spot.
- The mounting method: ground pad, wall brackets, roof support or riser, and how any penetration is flashed and sealed.
- The route for refrigerant lines, control wiring and condensate, including every point that crosses common property.
- Electrical scope: the new circuit, where it originates and whether the existing panel has capacity.
- Contractor licence numbers, WorkSafeBC coverage and a certificate of liability insurance naming the strata corporation where council asks for that.
- A statement that gas and electrical work will be done by licensed trades and permitted through the appropriate authority, with permit fees set by each municipality or Technical Safety BC.
- Expected number of working days, crew size, noise-producing stages and any elevator or parking requirements.
- A short note on sound: where the unit sits relative to neighbouring windows and patios, and what can be done with placement or mounting if sound is a concern.
What does the work actually require from the building?
Access is the quiet reason strata jobs slip. A crew that cannot get an elevator booking, a loading bay window, a parking spot near the work area or a key to a shared electrical room loses hours that no amount of planning on your side recovers. Ask council or the manager what the booking process is and what the notice expectations are, and do it before you pick a date.
Shutdowns are usually modest for a dual-fuel retrofit, because the furnace and ducting stay. Expect your heating to be off for part of a day or more while the coil goes in and the system is commissioned, and expect a short electrical interruption to your unit when the new circuit is landed. If any part of the work touches a shared gas or electrical service, that is a different conversation and one that needs the manager involved early.
Same-day work is sometimes possible for diagnostics or a small repair, and honestly it is not possible for a heat pump retrofit in a strata. That project is scheduled work with approvals, permits and building access behind it. We will not promise a guaranteed arrival window, and you should be wary of anyone who does.
Plan for the mess too. Brazing, coring a wall and running lines produce noise and dust. Telling council up front which day is the loud one, and offering to have neighbours notified, is usually the difference between a grudging approval and an easy one.
What does the Metro Vancouver context change?
Our climate is genuinely favourable for dual fuel. Mild wet winters mean a heat pump carries most of the heating season efficiently, while the gas furnace stays in reserve for the cold stretches, which is why we lead with the paired system rather than removing the furnace. It also means the outdoor unit lives in constant damp, so mounting it clear of standing water and pooling leaf litter matters more here than it would in a dry climate.
Density is the other factor. A third of the homes we look at are condos, townhouses or strata-governed duplexes, and in much of Burnaby, New Westminster, North Vancouver and East Vancouver the available outdoor space is a narrow side yard, a small patio or a shared walkway. Clearances and neighbour sightlines get decided in inches. On a townhouse with a rear lane or a small fenced yard there is usually a workable spot; in a stacked building the honest answer sometimes involves a balcony or roof location that council has to weigh carefully.
Older housing stock adds its own constraints. Buildings from the 1970s through the 1990s often have electrical panels with little spare capacity, which is why a panel assessment belongs in the site visit rather than being discovered on install day. Gas piping in older buildings may also need attention if any gas work is in scope, since undersized runs are a common blocker in older Metro Vancouver stock.
Metro Vancouver water is soft, which matters less for a heat pump than for hydronic systems, but it is worth knowing if your building also has gas boilers: local hydronic problems here tend to be sludge and corrosion rather than limescale.
What does a dual-fuel heat pump cost in a strata home?
Adding a heat pump to an existing gas furnace in Greater Vancouver is typically a ballpark $10,000 to $18,000 installed, before GST, with an electrical panel upgrade priced separately when one is needed. Those are ballpark figures for orientation only. They are not a quote, and an accurate price needs a site visit, because in a strata the access and routing decide as much as the equipment does.
If your furnace is old enough that replacing it makes sense at the same time, a high-efficiency gas furnace replacement is a ballpark $5,000 to $9,000 installed before GST, with complex jobs higher. Doing both at once usually costs less than doing them a few years apart, because the crew, the access booking and the approval process are shared. If a new or resized gas line is part of the scope, that runs a ballpark $500 to $1,500 for a short accessible run and $1,500 to $3,000 or more for a long or difficult one.
What moves the price on a strata job, more than anything, is the distance and difficulty between the furnace and the chosen outdoor location. A long line set through finished walls costs more than a short run through an exterior wall behind the furnace. Roof or bracket mounting costs more than a ground pad. A panel with no spare capacity adds electrical work. Condensate that has no nearby drain needs a pump and a route. Permits, disposal of removed equipment, code upgrades uncovered once things are open, and restricted working hours all add. Nobody can price those from a phone call.
Rebates and incentive programmes for heat pump work exist and change often, and qualifying usually depends on the equipment, the installation and the paperwork rather than on your strata status. We will not put a figure on any of that here. Ask what currently applies when you book, and treat financing questions separately from equipment pricing.
One more thing to be careful about: do not let anyone tell you a system upgrade returns a specific percentage at resale. Comfort, running cost and having cooling in a Metro Vancouver summer are real benefits. A resale percentage is not something anyone can honestly promise you.
How do you keep the job moving once approval is in?
Get the decision in writing, including any conditions council attached. Conditions are common and reasonable: a specific location, a particular mounting method, restricted work hours, a requirement that penetrations be sealed to a stated standard, or a clause making you and future owners of your unit responsible for the equipment and its fastenings. Read them before you sign an alteration agreement, and if a condition is technically impossible, say so before signing rather than after.
Then line up the practical pieces at once: the work date, the elevator or parking booking, access to any shared room, and the permitting handled by the licensed contractor. If you are doing this while listing, buying or turning over a rental, the timing is tighter and the strata process does not speed up for you, so start the alteration request as early as you can. For anything about notice, entry or disclosure obligations, talk to the Residential Tenancy Branch, your REALTOR or a lawyer, because those are legal questions and this is a trades page.
Keep a single folder with the bylaws you relied on, the written approval, the alteration agreement, the permit and inspection records, the equipment paperwork and the commissioning notes. It makes warranty claims simpler, it makes the next owner’s conveyancing simpler, and it settles any future argument about who is responsible for the unit hanging on the wall.
When should you call a licensed technician?
Call before you submit anything to council, not after. The site visit is what turns a request into something approvable, and it is also where impossible placements get identified before you have spent weeks on paperwork.
There is also work you must not do yourself. In BC, gas work and most electrical work are legally restricted to licensed trades, and refrigerant handling is restricted to certified technicians. That means you never open a refrigerant circuit, never top up or recover refrigerant, never alter gas piping or venting, and never land the new circuit in your panel. What you can reasonably do as an owner is read your bylaws, correspond with council, take photos of the proposed location, keep the outdoor unit clear of leaves and snow, change your filters on schedule, and keep the paperwork.
- Before submitting an alteration request, so the scope reflects a real placement and a real electrical assessment.
- Any time gas piping, venting or combustion equipment is being altered.
- Any time refrigerant lines are opened, charged or recovered.
- If the furnace short cycles, the heat pump runs constantly in mild weather, or the system never switches between heat pump and furnace as expected.
- If you see water around the furnace or coil, or the condensate line backs up.
- If a breaker trips repeatedly on the heat pump circuit, which is a symptom to diagnose, not to reset again.
- If your carbon monoxide alarm sounds, or you smell gas, in which case leave the building first and call from outside.
Frequently asked questions
Do I need strata approval for a heat pump if the furnace is already mine?
Almost certainly yes, because the outdoor condenser, its mounting and the line routing usually touch common property even when the furnace inside your unit is yours. The indoor work is rarely the issue; the outdoor placement is. Check your own registered bylaws and ask council or your property manager in writing what their alteration process requires.
How long does strata approval usually take?
The single biggest factor is how often your council meets, since a decision generally waits for a meeting. Submitting a complete, decision-ready package matters more than chasing, because an incomplete request often means waiting a full meeting cycle for a second look. Ask early when council next meets and what their submission deadline is.
What if council says the outdoor unit cannot go where I wanted?
That is common in dense Metro Vancouver buildings and it is usually solvable. Alternate placements change the line set length, the mounting method and sometimes the electrical route, all of which affect price, so ask for the scope to be revised rather than assuming the project is dead. A site visit that looks at two or three candidate locations up front saves a round of paperwork.
Will the outdoor unit bother my neighbours?
Modern heat pumps are reasonably quiet, but in a strata the distance to the nearest bedroom window or patio matters more than the equipment rating. Address sound directly in your submission instead of waiting for it to be raised, and be willing to adjust placement or mounting to move the unit away from a sensitive window. Do not quote a decibel figure you have not verified against manufacturer documentation for the specific model.
Can I keep my gas furnace, or do I have to go all electric?
You keep it. We lead with dual fuel in Metro Vancouver: the heat pump carries the mild majority of the heating season and the gas furnace takes over during cold snaps. Keeping the furnace also simplifies the strata conversation, because you are adding equipment rather than changing how the suite is heated from the ground up.
Who is responsible for the heat pump after it is installed?
Alteration agreements commonly place ongoing responsibility for the equipment and its fastenings on the owner and on future owners of that unit, but the specifics vary and your agreement governs. Read any conditions before you sign, and keep the signed agreement with your unit’s records so the next owner inherits a clear paper trail. For a legal interpretation of the wording, talk to a lawyer rather than your contractor.
Can this be done same day if I am listing or closing soon?
No. A heat pump retrofit in a strata is scheduled work that sits behind approvals, permits and building access bookings, and we will not promise an arrival window we cannot keep. Same-day attendance is sometimes possible for a diagnostic or a small repair, not for this. If a sale is driving the timeline, start the alteration request as early as you can and talk to your REALTOR about what actually needs to be complete before closing.
Do I need a permit, and who pulls it?
Permitting applies to the gas and electrical portions of the work and is handled by the licensed contractor, not by you. Permit fees are set by each municipality or by Technical Safety BC, so the amount depends on where you live and what the scope is. Keep the permit and inspection records with your strata approval paperwork.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
Is a heat pump worth it in Vancouver?
What rebates are available for heat pumps in BC?
Should I get a ducted heat pump or ductless mini-split?
How long does a heat pump last?
Do heat pumps work in cold weather?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


