★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

High Bill With a Heat Pump in a Cold Month

Heat Pump

High Bill With a Heat Pump in a Cold Month
Home › High Bill With a Heat Pump in a Cold Month

High Bill With a Heat Pump in a Cold Month

Key takeaways

  • In a cold month a heat pump produces less heat per unit of energy and runs longer hours, so consumption rises even when nothing is wrong.
  • Auxiliary or backup heat is the single biggest driver of a bill spike; it is supposed to run in a cold snap, but it should not be running in mild weather.
  • The balance point is the outdoor temperature below which the heat pump alone can no longer keep up, and where backup starts carrying part of the load.
  • Compare consumption units on the bill for the same period last year alongside degree days, not the amount owing, because rates and billing days change.
  • Free checks a homeowner can do: filter, thermostat mode and setback behaviour, outdoor unit clearance, and whether emergency or auxiliary heat was left switched on.
  • A bill that climbs with no weather or habit change behind it can point to a defrost, refrigerant charge, airflow or control fault that needs measured diagnosis.

If your heat pump bill jumped in a cold month, the most common cause is not a broken heat pump: it is auxiliary or backup heat running far more hours than it does in mild weather, on top of the heat pump itself working harder and longer for every degree it delivers. Cold air holds less heat for the outdoor coil to collect, so the system’s output per unit of energy drops exactly when the house is losing the most heat, and the gap gets filled by the backup stage. That is normal physics, not a fault. What is not normal is backup heat running in mild weather, a thermostat left in emergency heat, a badly blocked filter, or a bill that climbs while the weather and your habits stayed the same. This page walks through it in order, from the checks that cost you nothing to the measurements that legally and practically need a licensed technician, so you can tell which of the four causes you are looking at: the weather, the house, the habits, or the equipment.

Why does a heat pump cost more to run in a cold month?

A heat pump does not make heat the way a gas furnace does. It moves heat from outdoor air into your house using a refrigerant circuit. The colder it gets outside, the less heat there is in a given volume of outdoor air, so the compressor has to work harder and run longer to deliver the same warmth indoors. The efficiency of that transfer is expressed as a coefficient of performance, and it falls as outdoor temperature falls. Every heat pump behaves this way. Nothing has gone wrong when it does.

At the same time, the house is losing heat faster. Heat loss through walls, windows and air leaks is roughly proportional to the difference between indoor and outdoor temperature, so a cold snap increases the demand side and reduces the supply side at the same moment. Two effects stacking in the same direction is why the jump on a bill can feel out of proportion to the drop in temperature.

Add the defrost cycle. In our damp coastal air, frost forms on the outdoor coil when it runs cold, and the system periodically reverses to melt it off. During defrost the unit is briefly not heating the house, and on most systems the backup stage comes on to stop cold air blowing out of the registers. Frequent defrosts in wet, near-freezing weather are normal and they add consumption. Constant defrosting, ice building up until the coil is a solid block, or a unit that never clears itself is a fault worth reporting.

What is auxiliary heat and why does it show up on the bill?

Auxiliary heat, also called backup or second-stage heat, is whatever the system uses to top up the heat pump when the heat pump alone cannot keep up. In a dual-fuel system, which is what we most often recommend and install in Metro Vancouver, the backup is the gas furnace: the heat pump carries the mild shoulder-season load and the furnace takes over in a cold snap. In a ducted system without gas, the backup is an electric element inside the air handler.

Backup heat is the part of a heat pump system that changes a bill the most, because it is far less efficient at converting purchased energy into delivered heat than the heat pump is in mild weather. Whether the backup is gas or electric, it is doing the same job: covering the shortfall. A cold month means more hours in that shortfall, which is the single largest line item behind most winter bill spikes.

This is also where honest diagnosis starts. Backup heat running during a cold snap is the system working as designed. Backup heat running on a mild wet evening, or running continuously regardless of weather, is a symptom. Many thermostats display an auxiliary or backup indicator when that stage is active, and some keep a runtime history. Watching that indicator over a few days in mild weather tells you a lot before anyone opens a panel.

What is the balance point and why does it matter to my bill?

The balance point is the outdoor temperature at which your heat pump’s output exactly matches your house’s heat loss. Above it, the heat pump can hold the setpoint on its own. Below it, something else has to make up the difference. Every house has its own balance point because it depends on the building’s insulation, air tightness, window area and the capacity of the installed equipment, not on the brand on the cabinet.

On a dual-fuel system the installer also sets a switchover or changeover point in the controls, the outdoor temperature at which the system hands the load to the gas furnace. If that switchover is set higher than it needs to be, the furnace takes over earlier than necessary and the heat pump does less of the cheap work. If it is set too low, the house can struggle to hold temperature on the coldest nights. Both settings are adjustable, both were chosen at commissioning, and both are worth revisiting if your comfort or your consumption has shifted.

A cold month simply means more hours spent below the balance point. That is why two winters with the same thermostat setting can produce very different consumption. Before assuming the equipment degraded, look at how cold it actually was and for how long.

What should I check myself before calling anyone?

Work through these in order. All of them are free, none of them require opening a sealed refrigerant circuit or touching gas piping, and any one of them can explain a surprising bill on its own.

  • Check whether emergency heat or backup-only mode is switched on at the thermostat. It is easy to select during a cold night and easy to forget. In that mode the heat pump is locked out and the backup carries everything.
  • Pull the filter and look at it against a light. A loaded filter starves airflow, which lowers delivered heat, lengthens run times and can trip the system into calling for backup.
  • Confirm the thermostat is in heat or auto, not in a mode that fights itself, and confirm the fan is set to auto rather than on. A fan running continuously adds consumption and can make air feel cool.
  • Look at your setback schedule. Deep overnight setbacks that a heat pump then has to recover from in the morning often pull in backup heat during the recovery, which can cost more than holding a steadier temperature would have.
  • Check the outdoor unit. It needs clear space around it and underneath it. Clear snow, leaves, cedar debris and anything stacked against the cabinet. Never chip ice off the coil or pour hot water on it.
  • Check for an obvious change in the house: a window left cracked, a bathroom fan left running for days, a door to an unheated garage or crawlspace not latching, a broken window seal.
  • Check for a change in habits: guests staying, someone home all day who was not before, a new space heater, a new hot water demand, a thermostat raised by another member of the household.
  • Read the bill itself, not just the total. Find the consumption units and the number of billing days, and note whether the period covered a cold stretch.

How do I compare one bill to another fairly?

Comparing the amount owing between two bills tells you almost nothing, because billing periods differ in length and rates change independently of your equipment. Compare consumption instead. Electricity is billed in kilowatt-hours and natural gas in gigajoules, and both figures appear on the bill along with the number of days in the period. Divide consumption by days to get a per-day figure, which makes a short period and a long period comparable.

Then put weather beside it. Heating demand tracks heating degree days, a published measure of how far and how long the outdoor temperature sat below a reference point. A month with many more degree days than the same month last year should use more energy. If consumption per day rose roughly in step with degree days, the weather explains the bill. If consumption per day rose while degree days did not, something in the house, the habits or the equipment changed.

The table below sorts the usual suspects by what the pattern looks like.

What the pattern looks likeMost likely driverWhat to do next
Consumption per day rose, and it was clearly a colder stretchWeather and normal backup operationNothing is wrong; review the switchover setting and the setback schedule for next winter
Backup or auxiliary indicator lights up even in mild weatherControl setting, sensor, staging or a lockout left engagedConfirm emergency heat is off, then book a control and staging check
Rooms feel cool, system runs almost constantlyAirflow restriction, duct leakage, undersized or degraded capacityChange the filter, then have airflow and static pressure measured
Outdoor unit ices over and does not clear itselfDefrost control, sensor, drainage or refrigerant faultShut the system off at the thermostat and book a technician
Consumption rose with no weather change and no habit changeEquipment or control fault, or a combustion issue on the gas sideBook a diagnostic; do not keep running a system you suspect
Gas consumption rose sharply on a dual-fuel systemSwitchover point set high, heat pump locked out, or furnace running inefficientlyHave the changeover setting and the furnace combustion checked

What does Metro Vancouver’s climate do to heat pump bills?

Our coastal winters are mild but wet, and that combination is specific. Most of our heating season sits in the temperature band where a heat pump is at its best, which is exactly why heat pumps make sense here. The trouble is the humidity: air near freezing and saturated with moisture builds frost on an outdoor coil far faster than the dry cold of the interior. More frost means more defrost cycles, and more defrost cycles mean more backup heat and more consumption in the wettest weeks even without a hard cold snap.

Then there is the housing stock. A great deal of Metro Vancouver is pre-1990 construction with modest insulation, single-pane or early double-pane windows and leaky building envelopes. A house like that has a high heat loss, which pushes its balance point upward, which means backup heat engages at a milder outdoor temperature than it would in a newer, tighter home. The same equipment in a newer house would produce a very different bill. Envelope improvements, weatherstripping and attic insulation often do more for a winter bill than anything done to the mechanical equipment.

Strata and townhouse living adds its own wrinkle. Ductless heads serving different suites or different zones, shared walls that leak heat between units, outdoor units tucked into balconies or narrow side yards with poor airflow, and strata rules on equipment placement all affect how a system performs. If your outdoor unit is boxed into a tight alcove and recirculating its own cold discharge air, it will run longer for less result.

One more local note: because our winters are mild overall, a dual-fuel system spends most of the season on the heat pump and calls the gas furnace only for the genuine cold snaps. That balance is the reason we lead with dual fuel here, and it is also why the switchover setting deserves attention. It decides how much of the season each appliance carries.

Can a high bill be a safety problem rather than a cost problem?

Sometimes, yes, and it is worth saying plainly. On a dual-fuel system, the backup is a gas furnace, and a furnace that is burning poorly can consume more gas while delivering less useful heat. A cracked heat exchanger, a partially blocked flue, a bird nest or debris in the vent termination, a dirty burner or an air supply problem can all show up first as an unexplained increase in consumption or as a house that never quite gets warm. Every one of those is also a combustion safety concern, not just an efficiency concern.

Carbon monoxide is colourless and odourless, and the early symptoms of exposure are easy to mistake for a winter bug: headache, nausea, dizziness, fatigue that lifts when you leave the house. Working CO alarms on every level of the home, including outside sleeping areas, are the only reliable warning. Test them when the heating season starts and replace them at the end of their rated service life, which is printed on the unit.

Natural gas is odourized so you can smell a leak. If you smell gas, do not investigate it. Leave the building, leave the door open behind you, do not use light switches, phones or anything that could spark while inside, and call from outside. If a CO alarm sounds, get everyone out into fresh air and call emergency services first.

When should I call a licensed technician?

The free checks above end where measurement begins. A homeowner can change a filter, clear the outdoor unit, read a thermostat and read a bill. A homeowner cannot safely or legally measure refrigerant charge, open a sealed refrigerant circuit, adjust gas pressure, check combustion or work inside the electrical compartment of an air handler. Refrigerant handling is restricted to certified technicians by law. Gas work and most electrical work in British Columbia is restricted to licensed trades. There is no homeowner version of those steps.

Call when the backup indicator runs in mild weather, when the outdoor unit ices over and will not clear, when the system runs constantly without holding setpoint, when a breaker trips repeatedly, when consumption rises with no weather or habit explanation, or when you suspect anything on the combustion side. Also call if you simply want the switchover and staging settings reviewed against how your house actually behaves, because a commissioning setting chosen on installation day is not always the right one two winters later.

A proper diagnostic on a heat pump in winter includes checking airflow and static pressure, verifying the defrost sequence, confirming stage and switchover logic at the thermostat and control board, checking refrigerant performance against manufacturer-published values for the specific model, and on a dual-fuel system verifying furnace combustion and venting. That is measured work, not a guess, and it is what separates a real answer from a parts swap.

BC Wide Home Services Ltd has served Metro Vancouver since 1999 and is an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029. We service the major heat pump, furnace and boiler brands as an independent contractor rather than as a factory-authorised dealer. Same-day attendance is often possible depending on the day and the call volume, and we will tell you honestly when it is not rather than promise an arrival window we cannot hold. Call (604) 473-9690 and describe what the thermostat is showing, what the outdoor unit looks like, and what changed on the bill, and ask for a written quote before any repair work proceeds.

Electrical safety: This article covers equipment that in most Metro Vancouver homes includes a gas furnace as the backup stage. Natural gas appliances produce carbon monoxide, which is colourless, odourless and dangerous. Install working CO alarms on every level of the home, including outside sleeping areas, test them at the start of the heating season, and replace them at the end of their printed service life. If you smell gas, leave the building immediately, leave the door open, do not operate light switches, phones or anything that could create a spark while inside, and call from outside. If a CO alarm sounds, get everyone into fresh air and call emergency services first. Gas work and most electrical work in British Columbia is restricted to licensed trades, and refrigerant handling is restricted to certified technicians. Do not open a sealed refrigerant circuit, adjust gas pressure, chip ice off an outdoor coil, or work inside the electrical compartment of an air handler. BC Wide Home Services Ltd, licences LGA0090068 and CGA0028029, (604) 473-9690.

Frequently asked questions

Is a higher heat pump bill in a cold month normal?

Usually yes. A heat pump delivers less heat per unit of energy as outdoor temperature drops, while the house is losing heat faster, so consumption rises on both sides at once. Add the hours that auxiliary or backup heat runs below the balance point and a cold month can look dramatically different from a mild one. It only becomes a fault when consumption climbs without a matching change in weather or household habits.

Should I switch my thermostat to emergency heat when it gets cold?

No. Emergency heat locks the heat pump out entirely and runs the backup alone, which is the most expensive way to heat the house. It exists for the situation where the heat pump itself has failed and you need heat until a technician arrives. A properly set up system brings in backup automatically when it is needed, so leave the thermostat in normal heat mode and let the controls do their job.

Does turning the thermostat down at night save money with a heat pump?

Less than it does with a furnace, and sometimes not at all. A heat pump recovers temperature slowly, so a deep overnight setback often pulls in backup heat during the morning recovery, and that recovery can consume more than holding a steadier temperature would have. A modest setback of a degree or two is generally fine. If your thermostat has an adaptive or smart recovery feature, enabling it helps it start the recovery gently rather than calling for backup.

How do I tell whether it was the weather or the equipment?

Compare consumption units per day, not the amount owing, between the current period and the same period a year earlier, then look at published heating degree days for both months. If consumption per day and degree days moved together, the weather explains it. If consumption per day rose while the weather was similar and nothing changed in the household, book a diagnostic.

Why does my outdoor unit steam and stop heating for a few minutes?

That is the defrost cycle, and it is normal. The system briefly reverses to melt frost off the outdoor coil, which produces visible steam and a pause in heating, and most systems bring in backup heat during those minutes so cold air does not blow from the registers. In our wet coastal winters defrosts are more frequent than in dry climates. What is not normal is ice building up until the coil is solid, or a unit that defrosts constantly and never clears.

Could a high bill mean something is wrong with my gas furnace rather than the heat pump?

Yes, particularly on a dual-fuel system where the furnace is the backup. A dirty burner, a restricted flue, a blocked vent termination or a cracked heat exchanger can increase gas consumption while delivering less usable heat, and each of those is a combustion safety issue as well as a cost issue. If gas consumption jumped without a matching cold stretch, have combustion and venting checked. Make sure CO alarms are installed and working in the meantime.

Will insulating or air-sealing my house lower the bill more than servicing the heat pump?

Often, yes, especially in older Metro Vancouver housing stock. A leaky envelope raises the house’s heat loss, which raises the balance point, which means backup heat engages at a milder outdoor temperature and runs more hours. Attic insulation, weatherstripping and sealing obvious air leaks reduce the load the equipment has to meet. Servicing still matters, but the two work together rather than competing.

What information should I have ready when I call?

Have the thermostat model and what it is currently displaying, including whether an auxiliary or emergency heat indicator is lit, plus the brand and model from the rating plate on the indoor and outdoor units. Note when the filter was last changed, what the outdoor unit looks like, and the consumption figures and billing days from the recent bills you are comparing. Call (604) 473-9690 with that in hand and the diagnosis starts faster. Ask for a written quote before any repair work proceeds.

Related services & guides

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

Is a heat pump worth it in Vancouver?
Yes. Vancouver's mild winters (average lows above -5°C) are ideal for cold-climate heat pumps. A properly sized modern heat pump can cover 100% of heating and cooling for most homes, cut heating bills by 30–60% versus electric baseboards or oil, and qualifies for up to $11,000 in combined BC Hydro / FortisBC / federal rebates.
What rebates are available for heat pumps in BC?
Current rebates include up to $6,000 from CleanBC, up to $5,000 from the federal Greener Homes Grant, and additional income-qualified top-ups bringing the total to as much as $16,000 for eligible households. BC Wide is a registered contractor and handles the paperwork.
Should I get a ducted heat pump or ductless mini-split?
If you already have ductwork from a furnace, a ducted central heat pump is usually the better choice for whole-home comfort. Ductless mini-splits are ideal for additions, suites, garage conversions, and homes without ducts (radiant heated houses).
How long does a heat pump last?
A modern heat pump installed by a qualified contractor typically lasts 15–20 years. Annual maintenance, regular filter changes and keeping the outdoor coil clear of leaves and debris all extend service life.
Do heat pumps work in cold weather?
Modern cold-climate heat pumps from Mitsubishi, Daikin, Carrier, Lennox and Bosch maintain rated capacity down to -15°C and continue producing heat (at reduced capacity) down to -25°C — far colder than Metro Vancouver ever gets.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote