★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Tank to Tankless Conversion in Port Moody

Water Heaters

Tank to Tankless Conversion in Port Moody
Home › Tank to Tankless Conversion in Port Moody

Tank to Tankless Conversion in Port Moody

Key takeaways

  • A tank-to-tankless conversion is not a swap. The new appliance needs its own sealed venting route, a gas supply sized for a much higher peak input, a condensate drain, and a dedicated electrical circuit.
  • In Port Moody the deciding factor is usually the mechanical space and the wall it sits against: a tankless unit vents horizontally through a sidewall, so an interior utility room in the middle of a floor plan costs more to convert than a garage or crawlspace wall.
  • Ballpark installed range for a tank-to-tankless conversion in Greater Vancouver is roughly $4,500 to $8,000 and up, before GST. That is orientation only, not a quote.
  • If the old tank shared a chimney with a furnace or boiler, removing it can leave an orphaned, oversized flue. That has to be resolved as part of the job, not afterwards.
  • Gas work and most electrical work in BC must be done by licensed trades under permit. A homeowner can clear access, choose the location and handle strata paperwork.
  • A conversion is the wrong answer in some homes. Where gas capacity, venting route and electrical all need work at once, a high-quality tank replacement often serves the household better.

If you have already decided to move from a gas storage tank to a gas tankless water heater in Port Moody, the job ahead is a small mechanical renovation rather than an appliance swap. The tankless unit fires at a much higher input than the tank it replaces, so the work is dominated by four things: a new sealed vent route through an exterior wall, gas piping and a meter able to feed that peak input, a condensate drain with neutralisation, and a dedicated electrical circuit. On top of that sits the disposal of the old tank, resolving whatever chimney or common vent the tank was using, a City of Port Moody permit and Technical Safety BC gas permitting, and strata approval if you are in one of the townhouse or apartment complexes around Klahanie, Suter Brook or Newport Village. Done properly by a licensed contractor, most single-family conversions run one long day to two days on site. This page walks through exactly what happens, what you decide, what moves the price, and the honest cases where staying with a tank is the better outcome.

What does a tank to tankless conversion actually involve in a Port Moody home?

The old gas tank comes out first: gas isolated and capped by a licensed gas fitter, water isolated, the tank drained and carried out. Nothing about that part is difficult. Everything after it is where the work sits.

The tankless unit gets mounted on a wall, usually within a few metres of an exterior wall so its vent can terminate outdoors. A modern condensing tankless unit uses a sealed, direct-vent system: it draws combustion air from outside and pushes flue gases outside through plastic vent material rated for condensing appliances. That is a different vent category from the old tank’s draft hood and metal flue, so none of the existing venting is reused.

Water piping is re-run to the new unit’s inlet and outlet, with isolation and service valves that let a technician flush the heat exchanger later. Gas piping is checked and very often upsized, because the tankless unit’s peak input is far higher than the tank’s even though it only runs when you draw hot water. A condensate line is run to an approved drain with a neutraliser in the path. An electrician or the licensed contractor’s electrical scope provides a dedicated circuit and receptacle. Finally the system is purged, pressure tested, fired, combustion is checked, and the installation is left for inspection.

None of the gas or electrical steps are homeowner work in British Columbia. What you can do is clear the space, decide the location and vent termination point with your installer, and deal with your strata or neighbour conversations before crews arrive.

  • Remove and dispose of the old tank, cap the redundant gas connection
  • Mount the tankless unit and run a new sealed direct vent to an exterior wall
  • Upsize or re-run gas piping, and verify the gas meter can support the new peak load
  • Re-pipe hot and cold with isolation and flush valves
  • Run condensate to an approved drain with neutralisation
  • Provide a dedicated electrical circuit
  • Resolve any chimney or common vent the tank was sharing
  • Permit, pressure test, commission and pass inspection

Why does Port Moody housing stock change the cost of this job?

Port Moody is not one housing type, and the conversion is priced by the building, not by the brand of unit. The older neighbourhoods around Moody Centre and College Park are dominated by post-war and 1960s to 1980s single-family homes with basements, and those are usually the easiest conversions. The water heater tends to sit in a basement utility room or beside the furnace, an exterior wall is close, and there is a laundry standpipe or floor drain nearby for condensate. Those homes also tend to have the oldest gas piping, so upsizing a run from the meter is the common cost driver rather than the vent.

Heritage Mountain, Heritage Woods and the newer Anmore-adjacent streets bring 1990s and 2000s homes with attached garages and mechanical rooms that are often on an interior wall, sometimes on an upper floor. When the appliance is not against the building envelope, the vent has to travel, and every metre of vent, every elbow, and every bit of drywall or soffit you open to get there adds labour and finishing.

The townhouse and apartment stock at Klahanie, Suter Brook and Newport Village is a different problem again. Mechanical closets are tight, the exterior wall may face a courtyard or walkway where a vent termination has to be positioned carefully away from windows, doors and walkways, and the strata controls the building envelope. Nothing penetrates that wall without written approval.

Finally, the flat-lot older homes near the inlet often have crawlspaces rather than full basements. A crawlspace conversion is workable but it constrains where the unit can hang, how condensate drains by gravity, and how easily you can get to the unit for annual service.

What does the venting route decide, and what happens to the old chimney?

Venting is the single biggest variable in a Port Moody conversion. A condensing tankless unit vents horizontally through a sidewall with its own intake and exhaust. The termination has to sit a required distance from windows, doors, mechanical air intakes, decks, walkways and the property line, and the required clearances are published in the manufacturer’s manual and in the gas code. Your installer measures the actual wall, not a rule of thumb. On a tight side yard between two Port Moody houses, that clearance is what forces a unit to move to a different wall.

The second half of the story is what the old tank leaves behind. In a lot of older Port Moody basements the tank and the furnace or boiler shared a masonry chimney or a common B-vent. Pull the tank out and the remaining appliance is now venting alone into a flue that was sized for two appliances. That oversized flue can run cool, condense, and vent poorly. It is a genuine safety issue, not a formality.

There are only a few correct outcomes. The chimney is relined to the size the remaining appliance needs. Or the remaining appliance is already a sealed direct-vent unit and the chimney simply gets properly abandoned and capped. Or, on many conversions, the homeowner takes the opportunity to move the furnace or boiler to direct vent at the same time, which is more money now and fewer surprises later. What is never acceptable is walking away and leaving an orphaned appliance on an oversized flue. Ask any contractor you speak with how they plan to resolve it, and expect a specific answer.

Will my gas line and gas meter handle a tankless unit?

This is the question that quietly decides most conversions. A gas storage tank has a modest burner and heats water slowly over time. A tankless unit produces hot water on demand, so it fires at a much higher input for the minutes you are actually using hot water. The piping and the meter have to deliver that peak, at adequate pressure, while your furnace, range, dryer and fireplace may also be running.

A licensed gas fitter performs a load calculation on the whole house: total connected input, the length of each run, the number of fittings, and the pipe material and diameter. The result is either that the existing line is adequate, that a section has to be upsized, or that a new dedicated run from the meter is needed. In older Port Moody homes with small-diameter black iron running the length of a basement, a new run is common.

If the total household load exceeds what the meter and service can deliver, the gas utility must upgrade the meter or regulator. That is a utility process with its own timeline and it is arranged, not purchased from your contractor. It is worth raising early, because a meter upgrade can be the difference between a two-day job and a job that waits several weeks.

Manufacturer-published gas supply requirements for any particular model are in that model’s installation manual. Verify them for your model with your installer rather than assuming a number carried over from a neighbour’s install.

What gets checkedWhy it mattersWho is allowed to do it
Total connected gas loadDetermines whether the meter and service can feed the new peak demandLicensed gas fitter, with the utility for meter changes
Pipe diameter and run lengthLong small-diameter runs starve the unit at high fireLicensed gas fitter
Vent route and termination clearancesSets where the unit can physically hangLicensed contractor, per the manufacturer manual
Existing chimney or common ventAn orphaned appliance on an oversized flue is a safety issueLicensed contractor
Condensate drain availabilityCondensing units make acidic condensate that must be neutralised and drainedLicensed contractor
Electrical panel space and circuitThe unit needs a dedicated circuit and a nearby receptacleLicensed electrical trade
Strata or municipal approvalControls wall penetrations and permittingHomeowner initiates, contractor supplies documentation

What about condensate, electrical and the smaller details people forget?

A condensing tankless unit pulls so much heat out of the flue gases that water vapour condenses inside it. That condensate is mildly acidic and it has to leave the building through an approved drain, usually through a neutralising cartridge that raises the pH before discharge. In a Port Moody basement the nearest laundry standpipe or floor drain is normally the target. In a crawlspace or an upper-floor closet where there is no gravity path, a small condensate pump is added, and a pump is one more thing that needs a service eye on it each year.

Electrically, a tankless unit needs a dedicated circuit for its controls, fan and ignition. Older Port Moody panels are frequently full. If there is no spare space, a subpanel or a panel change enters the scope, and that is real money that has nothing to do with the water heater itself. Ask for the panel to be looked at during the site visit, not on install day.

The smaller items add up too. Isolation and service valves belong on the unit so it can be flushed without cutting pipe. A properly sized water line matters, because a tankless unit will not deliver its rated flow through undersized supply piping. Seismic and mounting hardware must be right for the wall type. If the old tank sat on a stand and the new unit hangs on the wall, you also get a useful amount of floor space back, which in a Port Moody townhouse closet can be the real reason a household converted in the first place.

What does it cost, and what moves the number?

A tank-to-tankless conversion in Greater Vancouver runs a ballpark $4,500 to $8,000 and up installed, before GST. These are ballpark figures for orientation only, not a quote, and an accurate price for your home needs a site visit. Two homes on the same Port Moody street can land at opposite ends of that range because of a wall, a pipe run or a panel.

For comparison, a straightforward tankless installation where the venting, gas and electrical already suit the appliance is a ballpark $3,900 to $7,800 installed, before GST, while a like-for-like gas tank replacement runs a ballpark $1,800 to $3,000 for an atmospheric unit and $2,800 to $4,500 for a power vent unit. A separate new gas line for an appliance is a ballpark $500 to $1,500 for a short accessible run and $1,500 to $3,000 or more for a long or difficult one. Ranges are wide because the building decides the work.

Permit fees are set by the City of Port Moody and by Technical Safety BC and are not part of these ranges. Any rebates or incentives available for high-efficiency gas water heating change from year to year and are handled qualitatively here on purpose; check the current programme terms yourself before counting on one. Financing and service visit charges are discussed when we scope the job, not estimated on a web page.

  • Vent route length, elbows, and how much finishing work the penetration creates
  • Whether the gas line must be upsized or a new dedicated run pulled from the meter
  • Whether the gas meter or regulator needs a utility upgrade
  • Condensate path: gravity drain nearby versus a pump and new drain line
  • Panel capacity and whether a dedicated circuit can be added easily
  • What has to happen to an orphaned chimney or shared vent
  • Access: a tight crawlspace or a third-floor closet takes longer than a basement
  • Water piping size and any code upgrades triggered by opening the system

When is a conversion the wrong answer for a Port Moody home?

Some homes should not convert, and saying so is part of doing the job honestly. If the mechanical space sits deep inside the floor plan with no practical vent route, the gas line needs a full new run from the meter, the panel is full, and there is no gravity condensate path, you are stacking four separate scopes on top of the appliance. In that house a high-efficiency gas tank, or a power vent tank if venting is the specific constraint, delivers reliable hot water for far less disruption.

Strata buildings are the other common case. If the strata will not approve a new wall penetration, the conversion simply is not available, and arguing about it wastes everyone’s time. Some Port Moody complexes are comfortable with it, some are not, and you find out by asking the strata council in writing before you book anything.

Usage pattern matters as well. A household whose peak is one shower at a time and a dishwasher gets less practical benefit from continuous hot water than a full house with several simultaneous draws. And if your existing tank is only a few years old and working, converting now means throwing away serviceable equipment. There is no urgency created by anything except failure.

Where a conversion is clearly right: the tank is at end of life, the mechanical space is on or near an exterior wall, the household runs multiple hot water draws, and you want the floor space back. That is a very common profile in Port Moody’s older single-family stock, which is why the conversion is so popular here.

How do permits, strata approval and the schedule actually work?

Gas work in British Columbia is permitted work. The licensed gas contractor takes the gas permit, and the installation is subject to inspection by Technical Safety BC or, in some cases, by the local authority. Building or plumbing permitting for the mechanical change goes through the City of Port Moody, and electrical work is permitted under the electrical trade doing it. Your contractor arranges these; your part is signing where required and giving access on the inspection date.

If you are in a strata, approval happens before permitting, not alongside it. Council will typically want to see the proposed termination location, the equipment, proof of licensing and insurance, and sometimes a scheduled window that suits the building. Give that process weeks, not days.

On-site, a straightforward single-family conversion is commonly one long day, with two days being normal when the gas line is being re-run or the chimney is being relined or abandoned. You will be without hot water for the working portion of that. If a gas meter upgrade is required, the utility timeline controls the calendar and the install is booked after it. Same-day work is sometimes possible for an emergency tank failure, but a same-day conversion is not realistic once permits, venting and gas capacity are in play. If your tank has failed and you need hot water now, the honest sequence is a temporary or like-for-like solution first and a planned conversion afterwards, or a fast-tracked conversion booked properly within days.

What should I expect from the unit after it is installed?

Expect continuous hot water rather than instant hot water. There is still a short delay while water travels from the unit to the tap, exactly as there was with a tank. If that delay bothers you, the answer is recirculation, and this is where models genuinely differ.

There are three distinct approaches and they are not interchangeable. A unit with a built-in recirculation pump has the pump inside the appliance and is the cleanest route when there is a dedicated hot water return line. Bradford White’s Infiniti L Series and Infiniti GR Series and Rheem’s IKONIC SR Series and RTG-R are examples of units built with a pump on board. A unit without a built-in pump can still be recirculated with an external pump installed on a dedicated return line, which is the approach used with Bradford White’s Infiniti K Series and Infiniti GS Series or Rheem’s IKONIC S Series and Prestige RTGH condensing units. And where no return line exists, which is most older Port Moody houses, a crossover or bypass valve retrofit uses the cold line as the return path at the farthest fixture. That third option is the cheapest to retrofit and the one with the most trade-offs, because it warms the cold line. Bradford White and Rheem are the tankless brands we install and service; BC Wide is an independent TSBC-licensed contractor, not a factory-authorised dealer for any manufacturer.

Maintenance is real but modest here. Metro Vancouver water is soft and cold, so the limescale problem that drives aggressive descaling schedules in hard-water regions is not our situation. Deposits here come from heat-driven mineral drop-out and from debris, and a periodic flush through the service valves plus an inlet screen cleaning handles it. Ask your installer what interval the manufacturer publishes for your model and follow that rather than a generic schedule.

Do not expect a tankless unit to fix a pressure or flow problem that comes from undersized or corroded water piping, and do not expect it to work during a power outage. It needs electricity for its controls and fan.

Gas & carbon-monoxide safety: This work involves natural gas and combustion appliances. If you smell gas, do not operate switches or appliances, leave the building immediately, and call from outside. Carbon monoxide is odourless: install CSA-certified CO alarms on every level of the home, including outside sleeping areas, and replace them at the manufacturer’s stated end of life. A conversion creates one specific hazard worth naming: when the old tank is removed from a shared chimney or common vent, the remaining furnace or boiler can be left venting alone into an oversized, orphaned flue that may spill combustion products back into the house. That must be resolved by relining, by converting the remaining appliance to direct vent, or by properly abandoning the chimney, as part of the same job. In British Columbia, gas fitting and most electrical work must be performed by licensed trades under permit, and the installation must be inspected. A homeowner may clear the work area, choose the location with the installer and handle strata paperwork, but must never alter gas piping, venting or electrical connections. BC Wide Home Services Ltd is a TSBC-licensed contractor, licences LGA0090068 and CGA0028029. To discuss a Port Moody conversion, call (604) 473-9690.

Frequently asked questions

How long does a tank to tankless conversion take in Port Moody?

Most single-family conversions run one long day on site, and two days is normal when the gas line has to be re-run or a chimney needs relining or abandonment. You are without hot water for the working portion of that time. If a gas meter upgrade is required by the utility, the install is scheduled after that utility work, which can push the calendar out by weeks.

Can I keep using my existing vent or chimney for the new tankless unit?

No. A condensing tankless water heater uses a sealed direct-vent system with its own intake and exhaust, in a different vent category and material from the old tank’s metal flue. The existing chimney is never reused for it. The chimney itself still has to be dealt with, either relined for whatever appliance remains on it or properly abandoned and capped.

Do I need a permit to convert from a tank to a tankless water heater?

Yes. Gas work in British Columbia is permitted and inspected work, taken out by the licensed gas contractor and inspected by Technical Safety BC or the local authority, and mechanical permitting goes through the City of Port Moody. Fees are set by those bodies rather than by the contractor. Your installer arranges the permits; you provide access for inspection.

Does soft Metro Vancouver water mean I can skip tankless maintenance?

It means the maintenance is lighter, not that you skip it. Our water is soft, so the heavy limescale seen in hard-water regions is not the local problem, but heat-driven mineral deposits and debris still accumulate in the heat exchanger and inlet screen. A periodic flush through the service valves at the manufacturer-published interval keeps the unit performing and protects the warranty terms you agreed to.

Will a tankless unit give me instant hot water at the tap?

No. It gives continuous hot water, but there is still a travel delay from the unit to the fixture, the same delay a tank had. Shortening that delay requires recirculation, which is either a unit with a built-in pump, an external pump on a dedicated return line, or a crossover valve retrofit where no return line exists. The right choice depends on whether your Port Moody home has a hot water return line.

My strata has to approve this. What do they usually want to see?

Councils typically want the proposed vent termination location on the building exterior, the equipment being installed, proof of contractor licensing and insurance, and a work window that suits the building. Approval must be in writing and must come before permitting and scheduling, because nothing penetrates a strata’s building envelope without it. Allow weeks for this step in Klahanie, Suter Brook, Newport Village and similar complexes.

Is a conversion ever a bad idea compared with just replacing the tank?

Yes, and it is worth saying plainly. If there is no practical vent route to an exterior wall, the gas line needs a full new run, the electrical panel is full and there is no gravity condensate drain, you are paying for four separate scopes on top of the appliance. In those homes a quality gas tank, or a power vent tank where venting is the single constraint, is the better value and the more reliable outcome.

Can you do a tank to tankless conversion same-day if my tank just failed?

A same-day like-for-like tank replacement is often possible; a same-day conversion generally is not, because permitting, venting and gas capacity work cannot be compressed responsibly and we will not promise an arrival window we cannot hold. The honest path when a tank fails suddenly is to restore hot water first and plan the conversion properly, or to book the conversion within days once the site has been assessed. Call (604) 473-9690 and we will tell you which applies to your home.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How long does a hot water tank last?
A standard gas or electric storage tank lasts 8–12 years. A high-quality tank with annual anode rod inspection can reach 15 years. Tankless water heaters typically last 18–22 years when descaled annually in Metro Vancouver's moderately hard water.
Should I switch to a tankless water heater?
Tankless makes sense if you have high demand (large family, multiple bathrooms running at once), want to free up floor space, or value endless hot water. Upfront cost is higher ($3,500–$6,000 installed vs $1,800–$3,200 for a tank) but operating cost is 25–40% lower for gas tankless.
My hot water tank is leaking — is it an emergency?
If the leak is from the tank body itself (not a valve or fitting), the tank is at end of life and needs replacement, usually within 24–48 hours before it floods. Shut off the water supply and gas/electric to the tank and call us.
What brands of water heaters do you install?
We install and service Bradford White, Rheem, AO Smith, John Wood, Giant, GSW for storage tanks; and Navien, Rinnai, Noritz, Bosch and Rheem for tankless units.
Can I install a water heater myself?
In BC, gas water heater installations must be performed by a TSBC-licensed gas fitter and are subject to permit and inspection. Electric tanks require a licensed electrician for the connection. BC Wide handles permits as part of every installation.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote