- A tank-to-tankless conversion is not a swap. The old tank’s B-vent cannot be reused, so the job includes a new sealed venting route, a condensate drain, an electrical circuit and usually a gas line upsize.
- Gas capacity is the number one blocker in older Tsawwassen homes. A tankless burner fires far harder than a tank, so the branch line and sometimes the meter have to be sized for it.
- Ballpark installed range for a tank-to-tankless conversion in our area is roughly $4,500 to $8,000 and up. That is an orientation figure, not a quote, and an accurate price needs a site visit.
- If the old tank shared a chimney with a gas furnace, removing it can orphan and oversize that chimney. That is a genuine carbon monoxide hazard and has to be resolved as part of the work.
- Tsawwassen water is soft and cold. Descaling is about heat-driven mineral deposits and debris rather than hard-water limescale, but flush service still matters and the isolation valves must be installed for it.
- Sometimes the honest answer is a new tank. Low flow demand, a cramped mechanical closet with no exterior wall, or an undersized gas system can all make like-for-like the better buy.
If you have already decided to move from a gas storage tank to a gas tankless water heater in Tsawwassen, the question that matters is no longer which system is better, it is what the job actually takes in your house. The short answer: the appliance itself is the easy part. A conversion means a brand new sealed venting route through a wall or roof, a gas line and often a meter that can carry a burner several times the size of the tank’s, a dedicated electrical circuit, a condensate drain with neutralisation, isolation valves for future flushing, and a municipal permit with an inspection at the end. In Tsawwassen’s mix of 1960s to 1980s ranchers, split levels and later infill, the two constraints that decide most of the cost are where the unit can vent and whether the existing gas piping can feed it. A competent site visit answers both in about twenty minutes. This page walks through how the work runs, what you choose, what drives the price, and the cases where we will tell you to put in another tank instead.
What actually changes when you convert from a tank to tankless?
A gas storage tank is an atmospheric or power-vented appliance with a modest burner that heats water slowly and holds it. A condensing gas tankless unit has a much larger burner that fires only on demand, produces cool acidic exhaust, and needs electricity to run its controls and fan. Every one of those differences creates work.
The venting is the first thing to go. A tank’s B-vent or single-wall connector is designed for hot, buoyant, non-condensing flue gas. A condensing tankless unit produces exhaust cool enough that water vapour condenses inside the vent, and it is fan-forced rather than draft-driven. It requires a sealed plastic venting system in a category rated for it, run to a manufacturer-approved termination with its own clearances from windows, doors, soffits, gas meters and property lines. You do not reuse the old chimney or B-vent.
The gas supply is the second. Because the tankless unit has to produce all the hot water instantaneously rather than over an hour, its input is far higher than the tank it replaces. The branch line from the meter and sometimes the meter itself have to be checked for capacity. Undersized gas piping is the single most common reason a conversion quote comes back higher than a homeowner expected.
Then come the smaller but non-optional items: a dedicated electrical circuit, a condensate drain routed to an approved point with a neutraliser so acidic condensate does not eat metal drain piping, mounting and seismic support on a wall that can carry the unit, isolation valves so the unit can be flushed later, and in most cases relocating the water heater from wherever the tank sat to wherever the venting works.
How does Tsawwassen housing stock affect the job?
Tsawwassen is dominated by detached single-family homes built from the 1960s through the 1980s, a lot of them ranchers and split levels on generous lots, plus later infill and a newer band of homes on the east side and toward the ferry corridor. That housing profile shapes conversions in a specific way.
Many of those older houses have their water heater in a garage, a utility closet off the garage, or a crawlspace-adjacent mechanical area rather than in a full basement. That is often good news: a garage wall or an exterior wall close by makes a short, clean sidewall vent run possible, which is the cheapest and most reliable configuration. A short run also means fewer elbows, which matters because every elbow counts against the manufacturer’s maximum equivalent vent length.
The bad news in the same houses is gas piping. Original branch lines were sized for the appliances of the day, a furnace and a modest tank, and the run from the meter to a garage or a back utility room can be long. A long run of undersized pipe cannot deliver the volume a tankless burner wants at the moment the furnace is also firing. Sometimes the fix is a new correctly sized branch; sometimes the whole system needs re-evaluating; occasionally the meter needs upgrading, which is arranged with the gas utility.
Tsawwassen also sits on flat, low-lying land near the water, and crawlspaces here can be damp and tight. That affects condensate routing: the drain has to reach an approved termination with proper slope, and dumping acidic condensate into a crawlspace or onto soil is not an approved answer. Where gravity does not work, a small condensate pump is added and it needs its own power and a safety interlock.
Salt air is a real factor near the water and toward the dyke. Outdoor-rated tankless installations and exterior vent terminations are common and perfectly legitimate in our climate, but the termination location and any exterior metal deserve thought so you are not looking at corrosion in five years.
What does the conversion process look like from booking to inspection?
A conversion is a planned job, not a same-day rescue. If your tank has already failed and you are without hot water, be honest with yourself about the timeline: a proper conversion involves a permit and a fair bit of new piping and venting, and we would rather tell you that up front than have you shower cold for a week. Same-day work in that situation usually means a like-for-like tank now, or a temporary arrangement while the conversion is scheduled.
The sequence below is the normal shape of the job in Delta. Timelines vary with permit processing and equipment availability, and we will not promise you a guaranteed arrival window.
- Site visit and assessment. We look at the existing tank, the venting options, the gas meter and branch sizing, the electrical panel, the condensate route, and whether the unit can stay where the tank is or has to move.
- Design and written scope. You get a scope that names the venting category and route, the gas work required, the electrical work, the condensate plan, and what happens to the old chimney or vent if it is shared.
- Permit application. Gas work is permitted through the municipality or Technical Safety BC depending on the scope. Permit fees are set by the authority having jurisdiction, not by us.
- Installation day or days. Old tank drained and removed, new gas piping run and pressure tested, venting cut in and sealed, unit mounted and connected, water piping and isolation valves, condensate drain and neutraliser, electrical circuit, commissioning and combustion check.
- Commissioning. Gas pressure checked under load, exhaust verified, temperature set, controls configured, and the recirculation strategy set up if you chose one.
- Inspection. The authority having jurisdiction inspects the gas work. You should receive documentation of the permit and the completed inspection for your records and for a future sale.
What has to be checked before a conversion can be approved?
Every item in this table is a real go or no-go check on a Tsawwassen conversion. If any one of them cannot be resolved, the design changes or the conversion is the wrong call.
| What gets checked | Why it matters | What happens if it fails |
|---|---|---|
| Gas branch line capacity | A tankless burner draws far more gas than a tank, and it must still work while the furnace fires | New correctly sized branch run, or a larger main from the meter |
| Gas meter capacity | Total connected load may exceed what the existing meter can deliver | Meter upgrade arranged with the gas utility, adding lead time |
| Venting route and termination | Condensing units need sealed plastic venting with clearances from windows, doors, soffits and the meter | Relocate the unit, change to an outdoor-rated installation, or the conversion is not viable in that spot |
| Equivalent vent length | Every elbow and metre counts against the manufacturer maximum | Shorten the route, move the unit, or change vent size within what the manual allows |
| Combustion air and enclosure | Sealed combustion units draw air through the vent system, but the space still has rules | Direct-vent concentric or two-pipe configuration, or a different location |
| Condensate route and slope | Acidic condensate must reach an approved termination and not damage piping | Neutraliser plus a condensate pump with a safety interlock |
| Electrical circuit availability | Controls and fan need power, and a pump if fitted | New circuit by a licensed electrician; a full panel is rarely needed for this alone |
| Shared chimney status | Removing the tank can orphan and oversize a chimney still serving the furnace | Reline for the remaining appliance or abandon the chimney and revent the furnace |
| Wall structure and mounting | The unit and its piping have to be supported properly | Blocking or backing added, or a different wall chosen |
| Existing hot water piping | Long runs and old distribution affect wait time at the tap | Recirculation strategy chosen, or expectations set honestly |
What happens to the old chimney when the tank comes out?
This is the part most homeowners have never heard of, and it is the one with genuine safety consequences. In a lot of Tsawwassen homes of that era, the gas tank and the gas furnace share a single masonry chimney or a common B-vent. The chimney was sized for both appliances together.
Take the tank out and you have removed a significant share of the heat that kept that flue warm and drafting. The chimney is now oversized for the furnace alone, and it is orphaned. An oversized, cool flue drafts poorly, can condense moisture inside masonry, and in the worst case can spill combustion products back into the house. That is a carbon monoxide risk, not a theoretical one.
There are two legitimate resolutions. Either the chimney is relined to the correct size for the remaining appliance, or the chimney is abandoned and the furnace is revented, which in practice often means the furnace is the next thing to be replaced with a sealed-combustion unit that vents through a wall. A responsible conversion quote addresses this explicitly. If a quote is silent on a shared chimney, ask about it before you sign anything.
What do you actually have to decide as the homeowner?
Beyond the trade decisions, there are four real choices that belong to you.
Location. Staying where the tank was is convenient but the venting has to work there. Moving the unit to an exterior wall, a garage wall or outdoors often produces a simpler, cheaper and more reliable install, at the cost of some water piping changes.
Indoor or outdoor. Outdoor-rated units are a normal and sensible choice in our mild coastal climate, and they free up interior space. Rheem indoor units can be converted for outdoor use with a manufacturer kit. Outdoor installations put the unit where salt air and weather reach it, so location on the building matters.
Recirculation, and which kind. This is the decision that most affects how the system feels day to day, and it is covered in its own section below.
Brand and family. We install and service Bradford White and Rheem condensing gas tankless equipment. Bradford White’s Infiniti K Series comes in indoor and outdoor versions and has no built-in pump but is wired to run an external recirculation pump; the Infiniti L Series has a built-in pump; the Infiniti GR Series is a newer design with a built-in pump, and the Infiniti GS Series is its companion without one. On the Rheem side the IKONIC S Series is condensing and the IKONIC SR Series is condensing with a built-in pump, the Prestige RTGH condensing series has Canadian CRTGH variants, the RTG series is non-condensing with an RTG-R recirculation version, and Performance Platinum is the retail line. Capacities, flow rates, vent lengths and gas pipe sizes for any of these are manufacturer-published, and you should verify them for your specific model with the installer or in the manual rather than trusting a number quoted from memory. BC Wide is an independent TSBC-licensed contractor, not a factory-authorised dealer for any brand.
How do the three recirculation options differ?
If your main concern is how long you wait for hot water at the far bathroom, recirculation is the answer, and the three ways of doing it are genuinely different jobs.
A built-in pump means the recirculation pump is inside the water heater. It is the tidiest option and the easiest to commission, and it is why families like the L Series, GR Series and IKONIC SR Series. It still needs somewhere for the water to return from.
An external pump on a dedicated return line is the best-performing arrangement. A separate return pipe runs from the far fixture back to the heater, and a pump moves water around that loop on a schedule or on demand. Some homes already have a return line from a previous system. If yours does not, running one through finished walls and ceilings in a Tsawwassen rancher is real carpentry and real cost. The Infiniti K Series is designed for exactly this, wired for an external pump rather than carrying one.
A crossover or bypass-valve retrofit is the compromise for homes with no return line. A thermostatic crossover valve is installed under the sink at the end of the run, and it uses the cold water line as the return path. It is far less disruptive to install. The trade-off is that it warms the cold line near that fixture, so the cold tap runs tepid for a moment after a recirculation cycle. For a lot of households that is a fair trade; for some it is annoying. Say so at the site visit and we will plan accordingly.
Whatever you choose, recirculation runs the burner and the pump more, so it is a comfort decision with an operating cost attached. Scheduling or on-demand activation rather than continuous running is usually the sensible middle.
What does a tank-to-tankless conversion cost in Tsawwassen?
A ballpark installed range for a tank-to-tankless conversion in Greater Vancouver is roughly $4,500 to $8,000 and up, before GST. Those are ballpark figures for orientation only, they are not a quote, and an accurate price for your house needs a site visit, because the knock-on work is what moves the number.
For comparison, a straight tankless installation where the venting and gas are already suitable tends to fall in a ballpark range of about $3,900 to $7,800 installed, and a like-for-like gas tank replacement sits in a ballpark range of roughly $1,800 to $3,000 for an atmospheric unit or about $2,800 to $4,500 for a power vent unit. Again, ranges for orientation, not quotes.
Where new gas piping is needed, a new gas line for an appliance is a ballpark $500 to $1,500 for a short accessible run and $1,500 to $3,000 or more for a long or difficult one. That single item is why two houses on the same Tsawwassen street can get quotes that differ by thousands.
What moves the price, roughly in order of impact: the length and difficulty of new gas piping, and whether the meter needs upgrading; whether the unit stays put or moves, and the water piping changes that come with moving it; the venting route, the number of elbows, and whether the termination location needs a longer run; resolving a shared or orphaned chimney; condensate routing, and whether a pump is required; the electrical circuit and its distance from the panel; adding a recirculation return line versus a crossover retrofit; access, including tight crawlspaces and garage clutter; disposal of the old tank; and any code upgrades the inspection requires on work that is being touched anyway.
Permit fees are set by the municipality or Technical Safety BC, not by us. Rebates and incentives for high-efficiency water heating change periodically and are administered by the utility or the province, so we will point you at the current programs and help with documentation rather than quoting amounts. Financing is available and is discussed separately from the installed price.
When is a conversion the wrong answer for your house?
We would rather talk you out of the wrong job than sell you it. Here are the honest cases where a like-for-like tank replacement is the better buy.
Your hot water demand is genuinely low. A one or two person household with a single bathroom and no simultaneous demand gets little practical benefit from instantaneous capacity. The conversion cost is real and the payback is not.
The mechanical space has no workable venting route. An interior closet in the middle of a house, with no accessible exterior wall and no viable roof path, can make the venting run so long or so invasive that the job stops making sense.
The gas system needs major work for this appliance alone. If the conversion triggers a new main from the meter plus a meter upgrade, and you have no other reason to do that work, the economics change sharply.
You are selling within a year or two. The money is better spent elsewhere. A functioning tank with documented maintenance is not a liability on a listing.
You need hot water back today. A conversion cannot be done safely and legally in an afternoon. If the tank has already failed, replacing it in kind now and planning the conversion later is a perfectly reasonable sequence, and no one should pressure you out of that.
Conversely, the strong cases are a household that actually runs out of hot water, a house where floor space in a small mechanical room has real value, a home already due for gas or venting work for other reasons, and a homeowner planning to stay long enough for the change to be worth it.
When do you need a licensed technician, and what can you do yourself?
In British Columbia, gas fitting is restricted work. Running, altering, sizing or pressure testing gas piping, connecting the appliance, setting gas pressure, and performing the combustion check all require a licensed gas fitter working under a permit. Most electrical work requires a licensed electrician. Neither is a homeowner task, and doing it yourself will also void the appliance warranty and fail inspection.
What you can reasonably do yourself: keep the area around the unit clear, keep the vent termination outside free of leaves, snow and shrubs, watch for water on the floor and report it early, change or clean the inlet water filter screen if the manual shows an owner-serviceable one, test the carbon monoxide alarms on every level of the house monthly, and keep your permit and inspection paperwork somewhere you can find it.
Call us right away if you smell gas, if a carbon monoxide alarm sounds, if the unit shows a fault code and will not clear, if you see soot or scorching near any gas appliance, if there is standing water under the unit or the condensate line, or if hot water has become erratic. Flushing and descaling service is done by a technician using the isolation valves installed with the unit; in Tsawwassen’s soft water, deposits are driven by heat and debris rather than limescale, so it is a routine service item rather than an urgent one, but it should not be skipped.
We are independently licensed by Technical Safety BC, licences LGA0090068 and CGA0028029, and we have been serving Metro Vancouver since 1999. To book a site visit in Tsawwassen, call (604) 473-9690.
Frequently asked questions
Can I reuse my old water heater vent for a tankless unit?
No. A condensing gas tankless unit produces cool, acidic, fan-forced exhaust that requires a sealed plastic venting system rated for that category, run to a manufacturer-approved termination with its own clearances. The old B-vent or masonry chimney was designed for hot, buoyant, draft-driven flue gas and cannot be reused. Planning that new vent route is one of the two decisions that shape the whole job.
Will my existing gas line handle a tankless water heater?
Often not without changes, and this is the most common surprise in Tsawwassen conversions. A tankless burner fires much harder than a storage tank, so the branch line has to be sized to deliver that volume while the furnace is also running, and occasionally the meter needs upgrading through the gas utility. A licensed gas fitter sizes the system during the site visit, which is why a genuine quote requires one.
How long does a tank-to-tankless conversion take in Tsawwassen?
The installation itself is typically a day, sometimes two when new gas piping, a relocation, or chimney work is involved. The overall timeline is longer because the permit has to be in place and the equipment has to be on hand. If your tank has already failed and you need hot water now, a like-for-like replacement today with the conversion planned properly afterward is usually the sensible route.
What happens to the chimney if my furnace shared it with the tank?
The chimney becomes orphaned and oversized for the furnace alone, which can cause poor draft, moisture inside masonry and in the worst case combustion spillage into the house. It is resolved either by relining the chimney to the correct size for the remaining appliance or by abandoning it and reventing the furnace. Any conversion quote you receive should address this explicitly rather than leaving it unmentioned.
Do I need a permit for this in Delta?
Yes. Gas work on a conversion is permitted through the municipality or Technical Safety BC depending on scope, and an inspection follows the installation. Permit fees are set by the authority having jurisdiction rather than by the contractor. Keep the permit and the completed inspection documentation, because it matters for warranty claims and when you eventually sell.
Does Tsawwassen water cause scaling in a tankless unit?
Metro Vancouver water is soft and cold, so you are not dealing with the hard-water limescale that drives descaling in other regions. Deposits still form from heat and debris, so periodic flushing remains part of proper maintenance, but it should not be oversold as an urgent recurring problem. What matters is that isolation valves are installed at the time of the conversion so the service can actually be done.
Will I still wait for hot water at the far bathroom after converting?
Yes, unless you add recirculation. A tankless unit heats water instantly but the water already sitting in your pipes still has to clear, and in a long single-storey Tsawwassen rancher that can be a noticeable wait. Your three options are a unit with a built-in pump, an external pump on a dedicated return line, or a thermostatic crossover valve retrofit that uses the cold line as the return path when no return pipe exists.
How much should I budget for a conversion?
A ballpark installed range for a tank-to-tankless conversion in our area is roughly $4,500 to $8,000 and up before GST, and that is an orientation figure rather than a quote. Where new gas piping is needed, a new appliance gas line adds a ballpark $500 to $1,500 for a short accessible run or $1,500 to $3,000 or more for a long difficult one. The venting route, the gas sizing and any chimney work are what actually move the number, so book a site visit at (604) 473-9690 for a real price.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
How long does a hot water tank last?
Should I switch to a tankless water heater?
My hot water tank is leaking — is it an emergency?
What brands of water heaters do you install?
Can I install a water heater myself?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


