How Do You Check a Quote Is for the Right Size?
- A quote is correctly sized when it names a heat loss calculation done for your house, and the furnace output matches that heat loss with a modest margin rather than a large one.
- Input capacity and output capacity are different numbers; sizing is done on output, and the difference is the efficiency rating on the appliance rating plate.
- In Metro Vancouver the winter design temperature is mild, so heat loss numbers here are usually lower than homeowners expect and oversizing is the more common error.
- Ductwork static pressure and airflow limit what the house can actually deliver, so a sizing conversation that never mentions ducts is incomplete.
- Ask for the calculation, the model’s output at the selected firing stage, and the proposed duct and venting changes in writing before you sign anything.
- Ballpark installed ranges exist for orientation only; the honest number comes from a site visit that measures the house.
A furnace quote is for the right size only if the contractor has calculated the heat loss of your specific house, room by room, and matched the furnace’s output capacity to that number with a sensible margin rather than a large safety cushion. To check it yourself, ask for three things in writing: the heat loss calculation and the design temperature used, the proposed furnace’s rated output at the stage it will actually run, and the airflow the installed ductwork can carry at the static pressure the system will see. If a quote gives you a model number and a price but cannot produce those three items, it has not been sized, it has been guessed, and the usual result is a furnace that is too large for the house. Everything below explains how to read each of those numbers, what makes them move, and how to tell a real calculation from a rule of thumb dressed up as one.
What does correctly sized actually mean for a furnace?
Sizing a furnace means matching how much heat the appliance can deliver to how much heat the house loses on the coldest design day. Heat loss is driven by the building envelope: wall and attic insulation, window area and glazing type, air leakage, the volume of conditioned space, and how much of the floor area sits over an unheated crawlspace or garage. A proper calculation adds those losses up room by room, not as a single whole-house guess.
The output that gets compared to that heat loss is not the number printed largest in the brochure. A gas furnace has an input capacity, which is how much gas energy it burns, and an output capacity, which is how much heat actually reaches the air after combustion and venting losses. The efficiency rating on the rating plate is the relationship between the two. Sizing is always done on output.
A correctly sized furnace runs long, steady cycles on a cold night and only rarely runs at full capacity, because the design day is by definition near the worst case. An oversized furnace satisfies the thermostat quickly, shuts off, and repeats. That short cycling makes rooms feel unevenly heated, is harder on the ignition and heat exchanger components over time, and wastes the efficiency you paid for, because a condensing furnace does its best work in a long steady burn rather than a series of starts.
How do I tell a real heat loss calculation from a rule of thumb?
In Canada the residential heat loss standard is CSA F280-12; many contractors also use the ACCA Manual J method, which arrives at the same kind of result. A real calculation names the standard, names the outdoor design temperature used for your municipality, and lists inputs: floor area by storey, ceiling heights, insulation levels for walls, attic and floors, window and door areas with their glazing type and orientation, and an air leakage assumption. It produces a room-by-room table, which is what makes duct sizing possible at all.
A rule of thumb produces a single number from floor area alone, or simply copies the capacity of the furnace being removed. Replacing like for like is the most common sizing error we see, because the original furnace was often oversized when it was installed decades ago, and because the house has usually been improved since: new windows, attic top-ups, better air sealing, sometimes an addition that changes the picture in both directions.
You are allowed to ask for the calculation. A contractor who sized the job properly has it as a document and can hand it to you. If what comes back is a verbal assurance that this size is what goes in houses like yours, treat that as an unanswered question rather than an answer.
- Ask which standard was used and what outdoor design temperature was assumed.
- Ask for the room-by-room output, not just a whole-house total.
- Ask whether the calculation used your current insulation and windows or an assumed default.
- Ask what the existing furnace’s output is, so you can see how far the new number moved and why.
Which numbers on the quote should I actually compare?
Most confusion in furnace quotes comes from comparing the wrong figures between two proposals. The table below names each figure, where you find it, and what it tells you. Verify every one of them against the rating plate on the appliance or the manufacturer’s own published documentation for the exact model number on the quote, not against a brochure for the product family.
Two-stage and modulating furnaces add a wrinkle. Those appliances have a low-fire capacity and a high-fire capacity, and a modulating unit covers a range between them. A well-sized modulating furnace spends most of the heating season at part load, which is exactly the point of paying for one. When you compare quotes, make sure you are comparing the same stage, and ask which stage the contractor sized against.
| Figure on the quote | Where you verify it | What it tells you |
|---|---|---|
| Heat loss of the house | The calculation document supplied with the quote | The target the furnace must meet on the design day |
| Input capacity | Appliance rating plate and manufacturer documentation | How much gas energy the burner consumes; not a sizing number on its own |
| Output capacity | Appliance rating plate and manufacturer documentation | The number that must match the heat loss; sizing is done here |
| Efficiency rating | Rating plate and manufacturer documentation | The relationship between input and output for that model |
| Low-fire and high-fire capacity | Manufacturer documentation for the exact model | How the furnace behaves at part load through a mild coastal winter |
| Rated airflow at external static pressure | Manufacturer blower tables plus the installer’s duct measurements | Whether your existing ducts can carry the air this furnace needs |
| Vent diameter and maximum vent length | Manufacturer venting tables for the model | Whether the planned vent route is legal and workable in your house |
Why does ductwork decide whether the size is right?
A furnace only delivers its rated output if the blower can move the rated volume of air through the duct system. Ducts resist airflow, and that resistance is measured as external static pressure. Older Metro Vancouver houses frequently have undersized returns, long flex runs with sags and tight bends, or supply trunks that were sized for a much smaller original system. Put a larger furnace on those ducts and it does not heat better; it simply pushes against more resistance, moves less air than it should, runs hotter across the heat exchanger and can trip its own high limit.
This is why sizing and distribution belong in the same conversation. A room-by-room heat loss tells the installer how much air each room needs; measuring or assessing the duct system tells them whether each branch can carry it. If one bedroom has always been cold, the fix is usually a distribution problem, not a capacity problem, and buying a larger furnace will not solve it.
If you are adding a heat pump to the furnace as a dual fuel system, airflow matters more again, because the indoor coil sits in the airstream and adds resistance, and because heat pump heating runs at lower supply air temperatures for longer periods. A duct system that was marginal for the furnace alone will show itself once a coil is added.
- Ask whether return air capacity was assessed, not just supply.
- Ask what external static pressure the installer expects and whether it will be measured at commissioning.
- Ask whether any duct modifications, new returns, or a new filter cabinet are included or excluded.
- Ask how a room that has always underperformed is being addressed in this scope.
What does a right-sized furnace replacement cost in Greater Vancouver?
A high-efficiency gas furnace replacement in Greater Vancouver typically lands in a ballpark range of about $5,000 to $9,000 installed, before GST, with complex jobs above that. These are ballpark figures for orientation only. They are not a quote, and an accurate price for your house needs a site visit, because the variables below move the number far more than the choice of model does.
Adding a heat pump alongside the furnace as a dual fuel system, with the gas furnace kept as backup for cold snaps, sits in a wider ballpark range of roughly $10,000 to $18,000 installed, with an electrical panel upgrade extra where the existing service cannot carry the new load. If the job needs a new or resized gas line for the appliance, that is commonly a ballpark range of about $500 to $1,500 for a short accessible run and $1,500 to $3,000 or more where the route is long or difficult.
Correct sizing does not automatically mean a cheaper furnace. A smaller output unit sometimes costs the same as a larger one in the same series, and a modulating furnace costs more than a single-stage one of the same output. What correct sizing buys you is a system that runs the way it was designed to, and a scope of work where the extras were identified before the truck arrived rather than discovered mid-installation.
Rebates, permit fees, financing arrangements and diagnostic or service-call charges are all separate line items and none of them are priced here. Permit fees are set by each municipality or by Technical Safety BC, rebate programs change their own terms, and those items should appear on your quote named clearly and separately from the installed price.
What moves the number inside the range?
The spread in any installed price range is the work around the appliance, not the appliance. Ask the contractor to point at which of these apply to your house, and ask which are included and which are allowances.
- Size and heat loss: a larger or leakier house needs more capacity and often more distribution work.
- Venting and its route: a condensing furnace needs new plastic venting to an approved termination, and a long, offset or awkward route adds material and labour.
- Chimney and orphaned appliances: removing a furnace from a shared chimney can leave a gas water heater improperly vented and requires a solution in the same scope.
- Gas line sizing: the existing line may be adequate for the old appliance but not for the new combination of appliances.
- Electrical capacity: dedicated circuits, a disconnect, or a panel assessment, which matters most on dual fuel jobs.
- Condensate handling: a condensing furnace produces acidic condensate that must be routed to an approved drain, sometimes with a neutraliser or a condensate pump.
- Access and removal: tight crawlspaces, narrow stairs, attic installations and strata corridors all add labour, and disposal of the old appliance is a real cost.
- Distribution changes: new returns, a resized trunk, a new filter cabinet, or registers relocated after a renovation.
- Permits and inspection: required for gas work, with fees set by the authority having jurisdiction.
- Stage and modulation choice: single-stage, two-stage and modulating equipment differ in price and in how they behave at part load.
What is different about sizing a furnace in Metro Vancouver?
Our winter design temperature is mild compared with most of Canada, which means calculated heat loss here is usually lower than homeowners expect and lower than the capacity of the furnace being replaced. That is the single biggest reason oversizing is so common locally: a like-for-like replacement carries forward a number that was generous when the house was built and is now clearly too large after decades of window and insulation upgrades.
The heating season is also long, wet and moderate rather than short and severe. Most of our heating hours happen well above the design temperature, so part-load behaviour matters more here than peak capacity does. That is a genuine argument for two-stage or modulating equipment, and it is also an argument against buying capacity you will never call on.
Housing stock varies enormously across Burnaby, Vancouver, Surrey, Coquitlam, Richmond, New Westminster, North Vancouver and the rest of the region, from uninsulated pre-war houses with converted gravity ducts to airtight new builds and strata townhouses with mechanical rooms the size of a closet. Strata properties add their own constraints: vent terminations have to land somewhere permitted, gas line routes cross common property, and the strata’s own approval process runs on its own schedule. Gas work requires permits and inspection, and the fees for those are set by each municipality or by Technical Safety BC, so they should appear on your quote as their own line.
When should I call a licensed technician?
You can do the paper part of this yourself. Reading the rating plate on your existing furnace, comparing output figures between quotes, asking for the heat loss calculation, checking that vent and gas line work is named in the scope, and confirming that permits are included are all homeowner tasks and you should do them.
Everything physical is not. In British Columbia, gas fitting is restricted to licensed gas fitters, and most electrical work is restricted to licensed electricians. Measuring static pressure, verifying combustion, sizing and inspecting gas piping, altering venting, commissioning the appliance and filing the permit are all licensed work. Refrigerant work on the heat pump side of a dual fuel system is legally restricted to certified technicians and must never be attempted by a homeowner.
Call a licensed technician when the furnace is short cycling, when rooms will not balance, when the existing appliance’s age or condition makes the replacement conversation real, or simply when you have two quotes with two different sizes and want the calculation done properly before you choose. BC Wide Home Services Ltd is an independent TSBC-licensed contractor in Burnaby, licences LGA0090068 and CGA0028029, serving Metro Vancouver since 1999. We install and service the major gas furnace brands; we are not a factory-authorised dealer, distributor or warranty centre for any brand. Same-day work is sometimes possible depending on the day’s schedule and parts availability, and we will tell you honestly when it is not rather than promise an arrival window we cannot keep. To have your heat loss calculated and your quote checked, call (604) 473-9690.
Frequently asked questions
Is it better to size a furnace a little larger to be safe?
No. A modest margin above the calculated heat loss is normal and expected, but a large cushion causes short cycling, uneven room temperatures and more wear on ignition and heat exchanger components. The design day calculation already represents a near worst case, so the safety margin is built in. Oversizing also stresses ductwork that was never designed for the extra airflow.
Can I just replace my old furnace with the same size?
Usually not, because the old furnace was often oversized to begin with and your house has probably changed since. New windows, attic insulation, air sealing or an addition all shift the heat loss. Ask for a fresh calculation and then compare the result with the old appliance’s output so you can see how far the number moved and why.
What is the difference between input and output capacity?
Input is how much gas energy the burner consumes; output is how much heat actually reaches the air after combustion and venting losses, and the efficiency rating on the rating plate connects the two. Sizing is always done on output. Quotes that only list input are not giving you the number you need to compare them fairly.
Do I need a heat loss calculation if I am also adding a heat pump?
Yes, and it matters more. In a dual fuel system the heat pump handles most of the mild coastal heating season while the gas furnace stays as backup for cold snaps, so the changeover design depends on knowing the house’s actual heat loss across a range of temperatures. Airflow also has to account for the indoor coil added to the airstream.
How do I check the airflow claim in a quote?
Ask what external static pressure the installer expects the duct system to produce and whether it will be measured at commissioning rather than assumed. Then ask for the blower table from the manufacturer’s documentation for that exact model, which shows the airflow the unit delivers at that pressure. If the ducts cannot carry it, the quote should include the duct work that fixes it.
Should the quote include the permit?
Gas work in British Columbia requires a permit and inspection, so the quote should state clearly that a permit will be pulled and who pulls it. Permit fees are set by each municipality or by Technical Safety BC rather than by the contractor, so they usually appear as a separate line item. A quote that never mentions permits is a quote worth questioning.
Why do two quotes recommend different sizes for the same house?
Almost always because one is based on a calculation and the other is based on the existing appliance or on floor area alone, or because the two used different assumptions about insulation, windows and air leakage. Ask both for the calculation and compare the inputs, not just the final capacity. The one that can show its assumptions is the one you can actually check.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
Are BC Wide technicians licensed and insured?
How can I book a service call?
Do you offer free estimates?
What brands do you service?
Do you offer government rebates for heat pumps?
How quickly can you replace a broken hot water tank?
Why should I choose BC Wide over other HVAC companies?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


