★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

How Much of the Price Is Labour?

Furnace

How Much of the Price Is Labour?
Home › How Much of the Price Is Labour?

How Much of the Price Is Labour?

Key takeaways

  • On a straightforward gas furnace changeout in Metro Vancouver, labour and installation materials commonly make up roughly one third to one half of the installed price; the appliance itself is the rest.
  • The furnace is a catalogue item with a fairly narrow price band. Labour is the variable, because it is priced against your house, not against the box.
  • Labour hours are driven by venting route, gas line sizing, condensate routing, electrical, access and removal, duct transitions, and permitting and inspection time.
  • Two quotes for the same furnace can differ by thousands of dollars entirely on the labour and materials side, and the cheaper one is sometimes the one that left work out.
  • Ask for the scope in writing rather than a labour dollar figure. What the crew will actually do tells you more than a percentage split.
  • Gas connections, venting and most electrical work in BC must be done by licensed trades and permitted, which is part of why installed labour costs what it does.

On a typical gas furnace replacement in Metro Vancouver, labour plus the installation materials the crew brings with them usually accounts for roughly a third to a half of the installed price, with the furnace itself making up the remainder. That share climbs toward, and sometimes past, half on older houses that need a new vent route, a resized gas line, a condensate path where none existed, or duct transitions to make a modern cabinet fit an old plenum. The reason the split moves so much is simple: the appliance is a catalogue item with a fairly narrow price band, while the work of putting it in is priced against your specific house. Two homeowners can buy the identical furnace and pay very different installed totals, and almost all of that difference sits on the labour and materials side of the ledger. This page explains how to separate the two on a quote you are holding, what pushes the labour portion up, and what to ask before you sign.

What counts as labour on a furnace quote?

Most homeowners picture labour as the hours the technicians are standing in the basement. That is part of it, but the installed price carries more than wrench time. A full changeout normally includes the site visit and heat loss assessment, the load and sizing decision, ordering and picking up equipment, protecting floors and stairwells, disconnecting and removing the old appliance, setting and levelling the new one, making the gas connection and pressure testing it, building or modifying the vent, running condensate, making the electrical and thermostat connections, adapting the supply and return plenums, commissioning and combustion checks, and then the permit, the inspection and the paperwork that closes the job out.

Alongside the hours sit the installation materials, and these are often bundled into what people loosely call the labour side: vent pipe and fittings, black iron or CSST for the gas run, a new gas cock and sediment trap, sheet metal for transitions, a condensate trap, tubing, a neutraliser where used, a condensate pump when gravity will not do it, flexible connectors, wire, a disconnect, thermostat cable, fasteners, sealant and duct tape rated for the application. None of these are expensive on their own. Together, on a job with a difficult vent or a long gas run, they are a meaningful line.

So when you ask how much of the price is labour, the honest answer is that you are really asking how much of the price is not the box. That is the number that varies, and it is the number worth understanding.

What does a furnace replacement actually cost in Metro Vancouver?

A high-efficiency gas furnace replacement in the Greater Vancouver area typically lands in the ballpark of $5,000 to $9,000 installed, before GST, with genuinely complex jobs going higher. These are ballpark figures for orientation only. They are not a quote, and an accurate price needs a site visit, because nobody can see your vent route, your gas line or your access from a phone call.

Applying the share above to that band, the labour and installation materials portion on a straightforward changeout often works out to somewhere in the low to middle thousands, with the equipment taking the rest. On a house where the furnace sits in a tight crawlspace, the vent has to be rerouted to a new termination, and the gas line needs upsizing, the same furnace can push the total to the upper end of that range or past it, and the extra is almost entirely work, not equipment.

If you are considering dual fuel, where a heat pump is added and the gas furnace stays as the backup heat source for cold snaps, the ballpark is $10,000 to $18,000, with an electrical panel upgrade extra when one is needed. Again, a range, not a quote. The labour share on a dual fuel job is usually higher than on a plain furnace changeout, because you are adding an outdoor unit, a pad or bracket, a lineset, an indoor coil, a condensate path for the coil, control wiring and a changeover strategy on top of everything the furnace alone would have required.

One line item that frequently gets folded in and then surprises people is gas piping. Running a new or upsized gas line for an appliance is a ballpark of $500 to $1,500 when the run is short and accessible, and $1,500 to $3,000 or more when it is long, buried in finished walls, or has to be upsized back toward the meter. That is a labour and materials item almost end to end.

Why is labour such a large share of the total?

Three things drive it. First, the work is legally restricted. In British Columbia, gas fitting is licensed work under Technical Safety BC, and most of the electrical connection is licensed work too. You are not paying for a person who can lift a furnace. You are paying for certified trades, their licensing, their tooling, their combustion analysers and manometers, their insurance, their vehicle, and the apprentice hours that produce the next generation of them.

Second, the work is custom every time. A furnace catalogue page is the same in Burnaby as it is anywhere else. Your mechanical room is not. Sizing, venting and duct transitions have to be solved for your house, and solving them takes time on site and sometimes a second trip for a fitting nobody could have predicted.

Third, the work is inspected. A permitted installation means the job has to be built so that a third party can look at it and pass it. That standard costs hours: proper support and slope on the vent, correct clearances, a real sediment trap, bonded and secured electrical, a condensate line that will not freeze or back up. Shortcuts save labour, which is exactly why a suspiciously low quote is usually a labour story rather than an equipment story.

What moves the labour number up or down on my house?

Use this as a checklist against your own property. Each item that applies pushes your quote toward the upper end of the range, and a quote that ignores an item that clearly applies is a quote worth questioning.

FactorWhy it changes the hoursWhat to look for at your house
Sizing and heat lossA proper load calculation and the resulting equipment and duct decisions take time and sometimes change the scopeHas anyone measured, or did they just match the old nameplate?
Venting routeMoving from an older chimney-vented setup to a sidewall-vented condensing furnace means new pipe, a new termination and clearance checksWhere does the current flue go, and where could a new termination legally sit?
Shared chimneyIf another gas appliance was sharing the chimney, orphaning it may force a liner or a change to that appliance tooIs a gas water heater venting into the same chimney?
Gas line capacityA new appliance can require a larger line or a longer run back toward the meterHow far is the meter, and is the run exposed or buried in finished space?
Condensate handlingCondensing equipment makes water that must drain safely, sometimes needing a pump and a route to a suitable terminationIs there a drain nearby, or is the furnace below every drain in the house?
ElectricalA dedicated circuit, a disconnect or panel capacity work adds licensed hoursIs there a labelled furnace circuit and an accessible disconnect?
Access and removalTight crawlspaces, narrow stairs, attic locations and long carries slow everything downCould two people carry a cabinet in and out without dismantling anything?
Duct transitionsNew cabinets rarely match old plenums, so sheet metal has to be fabricatedIs the existing plenum obviously wider or narrower than the furnace?
Distribution problemsExisting undersized returns or leaky trunk lines may need correction for the new system to performAre some rooms already far colder than others?
Permits and inspectionPermit application, scheduling and being on site for inspection are real hoursConfirm in writing that the quote includes permitting
Staging and modulationTwo-stage and modulating equipment involves more commissioning and control setupAsk what commissioning steps are included
DisposalThe old appliance and packaging have to leave and be disposed of properlyConfirm removal is included rather than left in your carport

How do I work out the labour split on my own quote?

Most contractors, including us, quote an installed price rather than an itemised equipment-plus-hours breakdown, and there is a good reason for that. An hourly quote on a job with unknowns behind a wall protects the contractor and exposes you. An installed price puts the risk of a surprise on the company that assessed the job. So do not treat a refusal to print a labour dollar figure as evasion.

You can still get at the split in a useful way. Identify the exact equipment on the quote by model, look it up in the manufacturer’s own published documentation to confirm it is the model and capacity you agreed to, and then recognise that whatever the total is, the difference between the two is the work. More usefully, ask for the scope in plain language and see whether the items on the checklist above are named.

  • Ask for the scope of work in writing: what gets removed, what gets built, what gets connected, what gets tested.
  • Ask specifically whether the permit and the inspection attendance are included, and whether the price changes if the inspector calls for something.
  • Ask whether venting, gas piping, condensate and electrical are inside the price or listed as possible extras.
  • Ask whether the old appliance removal and disposal are included.
  • Ask what happens if a hidden condition is found once the old unit is out, and how a change is priced and approved.
  • Ask what commissioning is performed and whether you receive the readings.
  • Compare two quotes on scope first and price second. If one is materially cheaper, find the line the other one has and it does not.

Why do two quotes for the same furnace differ by thousands?

Because they are not quoting the same job. One may assume the existing vent is reusable and the other may have looked at it and decided it is not. One may include the permit and the inspection visit and the other may leave permitting to you. One may have sized by measuring the house and specified a different capacity, which changes ducting. One may carry the gas line upsize inside the price and the other may plan to raise it as an extra once the crew is on site and you are committed.

None of that is visible if you compare only the model number and the bottom line. It becomes visible the moment you lay the two scopes side by side. In our experience in Metro Vancouver, the single most common gap between a low quote and a complete one is venting, followed by gas line capacity, followed by who is pulling the permit.

There is a related trap in the other direction. A high number is not automatically a thorough one. The test is the same either way: does the scope name the work your house actually needs, and does the company explain why each item is there?

What is different about furnace labour in Metro Vancouver?

Our housing stock is the biggest factor. A large share of Burnaby, New Westminster, East Vancouver, North Surrey and the North Shore is postwar and mid-century housing with mechanical rooms that were laid out for a mid-efficiency appliance and a masonry chimney. Converting that to a modern condensing furnace is genuinely a construction job, not a swap. Sidewall vent terminations have to respect clearances to windows, doors, meters, walkways and property lines, and on a narrow lot with a neighbouring house close by, finding a legal termination point can be the hardest part of the whole install.

Our mild, wet coastal climate cuts both ways. Peak heating loads here are modest compared with the rest of Canada, so oversizing is a common legacy problem, and right-sizing often means a smaller cabinet that needs new transitions. At the same time, long damp shoulder seasons mean furnaces here run for many hours at low load, which makes the quality of the commissioning and the duct work matter more than a spec sheet does.

Strata and townhouse density adds another layer. Shared walls, common-property corridors, restricted work hours, elevator bookings and strata approval for any exterior penetration all consume time that would not exist in a detached house. If you are in a strata, tell your contractor early, because it affects both the schedule and the hours.

Finally, permitting and inspection are municipal here. Requirements and timelines differ between municipalities, and gas permits fall under Technical Safety BC. Permit fees are set by each municipality or by Technical Safety BC and are a separate line item on your job, not something a contractor sets.

Which parts of this can I do myself, and which need a licensed technician?

You can genuinely reduce hours at the margins, and you should not try to reduce them anywhere else. Clearing the path is the honest homeowner contribution: move stored items away from the furnace and along the carry route, make sure the crawlspace hatch opens, confirm parking, contain pets, and have your strata approvals in hand before the truck arrives. You can also change your own filter, keep supply and return grilles unblocked, and find and photograph the rating plate on the existing appliance before anyone visits.

Everything on the connection side is licensed work in British Columbia. Gas piping, the gas connection, pressure testing, the vent system, combustion setup and most of the electrical work must be performed by appropriately licensed trades and, where required, permitted and inspected. Refrigerant work on a dual fuel system is restricted to certified technicians; a homeowner must never handle, top up or recover refrigerant. Attempting any of this yourself does not save labour. It creates a safety hazard, it can void equipment warranty coverage, and it can create problems at the time of sale when an inspection turns up unpermitted work.

When should I call a licensed technician?

Call before you commit, not after. A site visit is the only way anyone can tell you what the labour side of your job really looks like, and it is the visit that turns a range into a number. Call promptly if your furnace is showing any combustion symptom: a yellow or lazy burner flame where it should be blue and steady, soot marks, a persistent odour around the appliance, moisture or corrosion at the vent, repeated lockouts, or a carbon monoxide alarm sounding. If a carbon monoxide alarm is sounding, leave the building first and call from outside.

Call ahead of a planned replacement rather than waiting for a failure in January. Same-day work is sometimes possible and we will tell you honestly when it is, but a full changeout involves equipment availability, permitting and a crew, and those are not always same-day items. Planning in the shoulder season gives you a better shot at the right equipment and an unhurried install.

BC Wide Home Services Ltd has been installing and servicing gas heating in Metro Vancouver since 1999. We are an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029. We install and service the major furnace brands but we are not a factory-authorised dealer, distributor or warranty centre for any of them. To have your own house assessed and a scope put in writing, call (604) 473-9690.

Gas & carbon-monoxide safety: Gas appliances produce carbon monoxide, which is colourless and odourless. Install working carbon monoxide alarms on every level of your home and near sleeping areas, and test them regularly. If an alarm sounds, if you smell gas, or if anyone in the home has unexplained headaches, nausea, dizziness or drowsiness that improves when they leave the house, get everyone outside immediately, do not operate switches or your phone indoors, and call your gas utility’s emergency line from outside. Gas fitting, venting and most electrical work in British Columbia must be performed by licensed trades and permitted where required. Never modify a vent, a gas connection or a burner yourself, and never handle refrigerant on a dual fuel system.

Frequently asked questions

What percentage of a furnace installation is labour?

On a straightforward Metro Vancouver changeout, labour plus installation materials is commonly around one third to one half of the installed price, with the appliance making up the balance. On older homes needing a new vent route, an upsized gas line or duct transitions, the work side can reach or exceed half. The percentage is a rule of thumb, not a rule, because it is entirely driven by what your house requires.

Why will contractors not give me an hourly labour rate for a furnace install?

Because a furnace changeout has unknowns behind walls and under floors, and an hourly price would push the risk of those unknowns onto you. An installed price means the company that assessed the job carries that risk. Ask for a written scope of work instead; it tells you far more about the quote than an hourly figure would.

Does a more expensive furnace mean the labour costs more too?

Often yes, modestly. Two-stage and modulating equipment involves more control wiring and more commissioning time to set up and verify properly, and higher-efficiency condensing equipment requires condensate handling and a specific vent system. The bigger labour driver is still the house itself rather than the model you choose.

Is the permit fee part of the labour cost?

No. Permit fees are set by each municipality or by Technical Safety BC and are passed through as their own line item. What does sit on the labour side is the time spent applying for the permit, scheduling the inspection and being on site for it. Confirm in writing whether your quote includes permitting and inspection attendance.

Can I buy the furnace myself and just pay for labour?

We do not recommend it and most reputable contractors will not do it. Manufacturer warranty coverage generally depends on the unit being supplied and installed through proper channels, and when a homeowner supplies the equipment, nobody owns the outcome if the unit is the wrong capacity or arrives damaged. You also lose the contractor’s ability to stand behind the complete system.

Why is adding a heat pump to my gas furnace so much more labour?

Because you are adding a second system rather than replacing one. A dual fuel install adds an outdoor unit and its mounting, a refrigerant lineset, an indoor coil, a condensate path for that coil, control wiring and a changeover setup, plus electrical capacity work when the panel cannot support it. All of that is work and materials, which is why the installed range sits well above a furnace-only changeout.

How do I tell whether a cheap quote has cut labour corners?

Compare scopes, not totals. Look for whether venting, gas line sizing, condensate routing, electrical, duct transitions, permitting, inspection attendance, commissioning and old-unit disposal are each named. A quote that is silent on an item your house obviously needs has either missed it or plans to raise it as an extra once work has started.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.
Are BC Wide technicians licensed and insured?
Yes. BC Wide holds a TSBC gas-fitting licence, our technicians are Red Seal certified for HVAC and gas, and we carry full liability insurance and WorkSafeBC coverage.
How can I book a service call?
Call (604) 473-9690, email info@bcwide.ca, or use the booking form on bcwide.ca. Most calls are answered the same business day and we offer next-day appointments for non-emergency work.
Do you offer free estimates?
Yes. Free in-home estimates are provided for boiler, furnace, heat pump and water-heater replacements. Diagnostic visits for repairs carry a flat service fee that is credited toward the repair if you proceed.
What brands do you service?
We service all major brands including Viessmann, Navien, IBC, Rinnai, Rheem, Bradford White, Weil-McLain, Laars, Baxi, NTI, Lennox, Carrier, Bryant, Goodman, Trane, York, Daikin, Mitsubishi Electric, AO Smith, Bosch, Noritz, Giant, GSW, John Wood, and Valor.
Do you offer government rebates for heat pumps?
Yes. We are a registered contractor for BC Hydro, FortisBC and federal Greener Homes rebates. A high-efficiency heat pump installation can qualify for up to $11,000 in combined rebates depending on your home and income.
How quickly can you replace a broken hot water tank?
Standard 40 or 50-gallon gas or electric tanks are typically replaced same-day or next-day from stock. Tankless water heaters and larger commercial units usually take 1–3 business days depending on parts availability.
Why should I choose BC Wide over other HVAC companies?
BC Wide Heating & Air Conditioning has been operating in Greater Vancouver since 1999 as a TSBC-licensed (LGA90068) HVAC and gas contractor. We specialise in furnaces, boilers, heat pumps and water heaters across every major brand, we give honest options instead of upselling, and our work is performed by experienced, certified staff — not subcontractors.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote