★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Laars Boiler Code E40 — Gas leakage detected | BC Wide

Boilers, Error Codes, Hvac

Laars Boiler Code E40 — Gas leakage detected | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Laars Boiler Code E40 — Gas leakage detected | BC Wide

Laars Boiler Code E40 — Gas leakage detected | BC Wide

Quick answer

Laars boiler error code E40 means the control has detected a gas-leakage condition and put the boiler into a hard safety lockout, so expect no heat and, on a combi or indirect-tank setup, no hot water until it is cleared. Confirm the meaning against the manual for your unit. If you smell gas, leave now and call FortisBC or 911 from outside. Do not keep resetting. A licensed gas fitter must find the cause before the boiler goes back into service. BC Wide: (604) 473-9690.

If your Laars boiler is showing E40 (Gas leakage detected), here’s exactly what it means and what to do. This guide is part of our full Laars boiler error code list.

Severity: Critical — likely no heat / lockout.

What E40 means on a Laars boiler

The control detected a gas-leakage condition for more than 5 seconds, or three times within 10 minutes, and locked out (hard lock) for safety.

Common causes

  • Gas leak in or near the boiler cabinet
  • Off-gassing of new adhesives/sealants on a fresh installation
  • Cracked exhaust/flue piping
  • Gas valve fault

What you can safely check first

  1. If you smell gas, leave the area and follow your gas utility’s leak instructions
  2. Do not reset repeatedly — this is a safety lockout
  3. Call a licensed gas technician to inspect before returning the boiler to service

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Laars boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Laars boiler repair across Greater Vancouver

If a Laars boiler showing E40 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Laars boiler codes

Frequently asked questions

Is E40 on a Laars boiler serious?

It’s a lockout/safety code — the boiler has shut down and needs prompt diagnosis. BC Wide repairs Laars boilers 7 days a week across Greater Vancouver.

How do I reset a Laars boiler after E40?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Laars boiler error code E40: what it means for your heat, hot water and safety

In plain terms, E40 is the boiler telling you it stopped itself because it believes there is gas where there should not be. The control does not shut down gently and try again later the way it might after a minor ignition hiccup. It holds a hard lockout, which is why the display stays on E40 and the burner stays off. That is deliberate. The control is designed to assume the worst until a person proves otherwise, and the person who should do that proving is a licensed gas fitter with a calibrated combustible-gas detector, not a homeowner with a reset button. Confirm the exact wording of the code against the manual for your unit, because control generations differ.

What it means for your household depends on how the boiler is set up. If it heats the house through radiators, baseboard convectors or in-floor radiant loops, the heat stops and the house cools over several hours, faster in an older home with little insulation. If the boiler also makes domestic hot water, either as a combi or through an indirect storage tank, hot water stops too once the stored supply is used up. The circulator may run briefly after the lockout, which is normal and not a sign that the boiler is working.

These are the things owners usually notice first. Any one of them is worth mentioning when you call, because it helps us decide what to bring and how urgent the visit is.

  • The boiler display shows E40 and the burner will not fire, even with the thermostat turned up.
  • Radiators or heated floors are going cold, or there is no hot water at the taps.
  • A faint smell like rotten eggs near the boiler, the gas meter or the venting.
  • A new boiler, new venting or new gas piping went in recently and the code appeared within the first days or weeks.
  • Fresh paint, glue, sealant or strong cleaning products were used in the mechanical room shortly before the code.
  • The code clears after a reset and then comes back.

Laars E40 likely causes, most common first, and the checks you can safely do

The causes below follow the order we tend to find them on residential boilers, and they line up with the causes listed near the top of this page. The order is a guide, not a diagnosis: a real gas leak is always treated as the first possibility until a meter says otherwise, however unlikely it seems.

The owner-safe checks for any lockout are a short list, and none of them involves opening the boiler. Confirm the boiler’s power or service switch is on and the breaker has not tripped. Confirm the manual gas valve on the supply pipe to the boiler is open, with the handle in line with the pipe. Confirm the thermostat is calling for heat. Check that the outdoor intake and exhaust terminals are clear of snow, leaves and nests, and that the visible condensate drain line is not kinked or overflowing. If your manual allows a reset for this code, you may try one reset, once, and only when there is no gas smell and no CO alarm. If E40 returns, stop there.

What you must not do: open panels, remove the burner cover, unplug or jumper the sensing circuit, bypass the control, or reset the boiler over and over hoping it will stay on. Each of those either removes a safety layer or destroys the evidence the technician needs to find a leak.

Likely causeWhat you may safely checkWhen it becomes a licensed call
1. Vapours near the boiler from fresh adhesives, sealants, paint or solvents, especially on a recent installationThink back: was anything glued, sealed, painted or sprayed in the room recently? Do not bring more chemicals into the room. If there is no gas smell, open the door to the rest of the house to air the room.Always. Only a fitter with a gas detector can rule out a real leak before deciding the trip was caused by vapours.
2. A small gas leak at a fitting, union, valve or appliance connector in or near the cabinetIf you smell gas, check nothing: leave and call FortisBC or 911 from outside. Without a smell, you may look at the boiler’s manual gas valve position, but never loosen, tighten or soap-test fittings.Immediately. Gas piping and connections are licensed work in BC.
3. Cracked, separated or poorly sealed exhaust or flue pipingFrom outside, look at the intake and exhaust terminals for blockage or damage. Indoors, look without touching for a joint that has pulled apart or a visible crack.Immediately if you see damage, smell exhaust or a CO alarm sounds. Venting repairs are licensed gas work.
4. A gas valve faultNothing beyond confirming power is on and the gas supply valve is open. Never open the gas train or burner compartment.Always. The gas valve is a safety component that only a licensed technician tests or replaces.
5. The sensing circuit reading a condition that is not really thereNote whether the code returns at a particular time, for example when another gas appliance nearby runs, and tell the technician.Always. A reading can only be called false after a real leak has been ruled out with a meter.

When Laars error code E40 becomes a licensed gas call, and what to do if you smell gas

Practically speaking, E40 is a licensed call from the moment it appears. Many boiler codes leave room for an owner check to fix the problem, such as clearing a blocked condensate line. E40 does not, because the only safe way to clear it is to prove no gas is leaking, and that proof takes a calibrated combustible-gas detector, a pressure test of the piping where the findings warrant one, and an inspection of the venting. In BC, work on gas piping, gas valves and appliance venting is restricted to licensed gas fitters working under a licensed gas contractor.

Gas and carbon-monoxide safety comes before any troubleshooting. If you smell gas, or the code shows up together with a smell like rotten eggs, get everyone out of the house, pets included. Do not flip light switches, unplug appliances, ring the doorbell or start a car in an attached garage, because any spark can ignite gas. Once you are outside and well away from the building, call FortisBC or 911. If a carbon-monoxide alarm sounds, or anyone feels headachy, dizzy, nauseous or unusually sleepy, treat it the same way: get out first, then call 911 from outside. Do not go back in until the utility or fire department says it is safe.

Every home with a gas boiler should have working CO alarms on each sleeping level and near the mechanical room, tested regularly and replaced on the schedule printed on the alarm. Remember that a CO alarm is not a natural-gas detector. It does not respond to a gas leak, which is why the rotten-egg odorant added to natural gas matters so much.

Call us right away, even if you smell nothing, when any of the following applies.

  • E40 has appeared more than once, or came back after a single reset.
  • The boiler, its venting or its gas line was installed or modified recently.
  • You can see a separated vent joint, water staining on the vent pipe, or soot near the boiler.
  • Anyone in the home has had unexplained headaches or nausea that ease when they leave the house.
  • The house is losing heat and someone vulnerable, such as an infant or an older relative, lives there.

How our Laars E40 repair visit works, step by step

A good E40 visit is methodical, because the job is to prove where gas is coming from, or prove that it is not. This is how our licensed gas fitters run it.

  • Step 1, the phone call: we ask what the display shows, whether anyone smells gas, how old the boiler is and whether any work was done near it recently. If you smell gas, we tell you to leave and call FortisBC or 911 before anything else.
  • Step 2, safe entry: the technician checks the air at the door and in the mechanical room with a combustible-gas detector and a CO meter before touching anything.
  • Step 3, leak search: every accessible fitting, union, valve and connector on the boiler’s gas supply is checked with the detector and an approved leak-detection solution, and the piping is pressure-tested where the findings call for it.
  • Step 4, venting inspection: the exhaust and intake runs are inspected end to end for cracks, separated joints, missing supports and proper termination clearances outdoors.
  • Step 5, gas valve and control checks: with the right meters, the technician checks gas pressures, the gas valve’s operation and the control’s sensing circuit, and reads the fault history if the control keeps one.
  • Step 6, written findings and quote: before any work beyond diagnosis, you get the cause in plain language and a written quote for the repair. Nothing is replaced without your approval.
  • Step 7, repair and safety testing: once you approve, the repair is made, the system is retested for leaks, combustion is checked, and the boiler’s safeties are confirmed to shut it down when they should.
  • Step 8, paperwork: where the repair needs a gas permit, we take it out and arrange the inspection, and you keep a written record of what was found and done.

Repair or replace an older Laars boiler after an E40 lockout?

The parts most often involved in an E40 repair, in general terms, are a gas fitting or connector that needs to be remade, a section of vent pipe or a vent joint, the gas valve, and occasionally the sensing component or its wiring. Some of these are quick to correct on the first visit. A gas valve or control is one of the more expensive repairs on a boiler and may have to be ordered in. We tell you which applies before we start, and the boiler stays off until the part arrives, because running it with an unresolved gas fault is not an option. On timing, we offer same-day service where we can, depending on the day’s calls and your location, but we never promise a guaranteed arrival window.

An E40 lockout does not by itself mean the boiler is finished. A leaking fitting or a cracked vent section is a repair, not a replacement, on a boiler of any age. The question becomes real when the fault sits in a costly component on a boiler that is already near the end of its expected life, or when E40 is one of several problems turning up at once. The table shows how we weigh it with owners.

In Metro Vancouver, the heat exchanger question usually comes down to sludge and corrosion inside the hydronic loop rather than mineral scale, because our water is soft. An older system that was never treated or flushed can carry dark iron sludge that wears circulators and clogs heat exchangers, and that often weighs on a repair-or-replace decision more than the E40 fault itself. We look at it on every visit and tell you what we see.

If replacement makes sense, we lay out the options in writing: a like-for-like boiler, a combi that also handles domestic hot water, or a boiler paired with an indirect tank. Boiler and combi brands we service include Laars, Navien, Rinnai, Noritz, Bosch and A. O. Smith. We are an independent contractor, not a dealer for any of them, so the recommendation follows your house rather than a sales target. A new installation needs a gas permit and inspection, and you get a written quote before any work begins.

FactorLeans toward repairLeans toward replacement
Cause foundA fitting, connector, vent joint or vapour sourceGas valve or control on an aging boiler with other worn parts
Heat exchanger conditionClean, no corrosion, no signs of leakingCorrosion, sludge damage or signs of leaking
Parts availabilityParts readily availableParts discontinued or slow to source
VentingSound and meets current requirementsNeeds major rework regardless of the repair
Fault historyFirst lockout in yearsRepeated lockouts and repeat repairs
Your plans for the homeShort stay, boiler otherwise reliableLong stay, wanting better efficiency or a combi setup

Laars boiler error code E40 service near you in Greater Vancouver: who comes and where we go

BC Wide Home Services Ltd is an independent, Technical Safety BC-licensed gas contractor (licence LGA0090068, Class B gas CGA0028029) based in Burnaby and serving Metro Vancouver since 1999. Your E40 call is handled by licensed gas fitters, not general handypeople. We are not a Laars authorised dealer or warranty centre; if your boiler is still under manufacturer warranty, read the warranty terms first, and we will document our findings in writing so you can pass them along. Gas work is done under permit where one is required, inspections are arranged, and you see a written quote before any work beyond diagnosis.

Housing stock shapes how an E40 job goes. Here is what we commonly run into across the region, in general terms; every house is different and we confirm on site.

  • Vancouver: many older houses later converted to hydronic boilers, where gas piping has often been extended more than once and venting runs through tight basement mechanical rooms. Laneway homes and suites can add more connections to check.
  • Burnaby and New Westminster: a mix of older bungalows, mid-century homes and townhouse strata, where boilers often sit in closets or shared-wall mechanical spaces with longer vent runs.
  • Surrey, Delta and Langley: many newer subdivisions with sidewall-vented condensing boilers, where intake and exhaust terminals near decks, fences and landscaping can collect leaves and debris.
  • Richmond: homes on flat, low-lying lots where mechanical rooms are often in garages or main-floor utility rooms, and damp conditions make corroded fittings worth a close look.
  • Coquitlam and the Tri-Cities: hillside homes where vent terminals can sit close to grade, so snow or wet leaves during a cold snap can build up against them.
  • The North Shore: wetter and colder weather at elevation, older custom homes with radiant floors, and steep driveways, so please tell us about access when you call.
  • Strata owners: check with your strata manager before work on any gas piping or venting that runs through common property. We provide the written findings a strata council usually wants to see.
  • To book, call (604) 473-9690 and tell us the code on the display, whether you smell gas, and how the boiler is set up for heat and hot water.

More questions homeowners ask

What does Laars boiler error code E40 mean?

It means the boiler’s control has detected a gas-leakage condition and locked the boiler out in a hard safety lockout. The boiler will not fire until the cause is found and the lockout is cleared. Confirm the exact meaning against the manual for your unit, and treat it as a possible gas leak until a licensed fitter proves otherwise.

Can I reset a Laars boiler with error code E40?

Only if your owner manual allows a reset for this code, only once, and only if there is no gas smell and no CO alarm. If E40 comes back, stop and call a licensed gas technician. Resetting again and again does not fix the cause and can hide a real leak.

Is it safe to run my Laars boiler after an E40 error?

No, not until a licensed gas fitter has checked for leaks, inspected the venting and confirmed the safeties work. E40 is a gas-safety lockout, so the boiler should stay off until the cause is found and corrected. If you smell gas, leave and call FortisBC or 911 from outside.

Why does my new Laars boiler keep showing E40?

On a fresh installation, vapours from new adhesives, sealants or primers on venting and fittings can sometimes set off the gas-leakage detection. That is a possible explanation, never an assumption. A licensed fitter still has to rule out a real leak at the new connections with a detector before concluding it was vapours.

Can you fix Laars boiler error code E40 the same day in Greater Vancouver?

Same-day where we can, depending on the day’s schedule and where you are. Many E40 causes, such as a leaking fitting or a separated vent joint, can be corrected on the first visit, while a gas valve or control may need to be ordered. We never promise a guaranteed arrival time; call (604) 473-9690 for an honest answer.

Do I need a permit to repair a gas leak on a boiler in BC?

Gas work in BC must be done by licensed gas fitters, and many gas repairs and every boiler replacement need a gas permit and inspection. The licensed contractor takes out the permit; in the City of Vancouver gas permits are issued by the city, and in most other municipalities by Technical Safety BC. Ask for the permit number on your paperwork.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote