★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Laars Boiler Code E42 — Jumper wire disconnected | BC Wide

Boilers, Error Codes, Hvac

Laars Boiler Code E42 — Jumper wire disconnected | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Laars Boiler Code E42 — Jumper wire disconnected | BC Wide

Laars Boiler Code E42 — Jumper wire disconnected | BC Wide

Quick answer

Laars boiler error code E42 means a required jumper or link in the boiler’s wiring is missing or disconnected, and the control has gone into a soft lockout (confirm against the manual for your unit). Until that circuit is complete the boiler will not fire, so expect no heat and, if an indirect tank is connected, no hot water. Check power and the thermostat, allow one reset only if the manual permits it, then call a licensed technician at (604) 473-9690. Never add a jumper yourself.

If your Laars boiler is showing E42 (Jumper wire disconnected), here’s exactly what it means and what to do. This guide is part of our full Laars boiler error code list.

Severity: Needs attention.

What E42 means on a Laars boiler

A required jumper/link in the wiring is missing or disconnected. Soft lock.

Common causes

  • Missing or removed wiring jumper
  • Loose terminal or external control connection

What you can safely check first

  1. Confirm the boiler has power
  2. Have a technician confirm field wiring and jumpers — not a homeowner fix

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Laars boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Laars boiler repair across Greater Vancouver

If a Laars boiler showing E42 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Laars boiler codes

Frequently asked questions

Is E42 on a Laars boiler serious?

It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs Laars boilers 7 days a week across Greater Vancouver.

How do I reset a Laars boiler after E42?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Laars Boiler Error Code E42: What It Means for Your Heat and Hot Water

In owner terms, E42 is the boiler telling you that a circuit it expects to see closed is open. Most boiler controls have field-wiring terminals where an installer connects equipment that lives outside the boiler cabinet: a thermostat or zone controller, and on some installations extra safety or interlock devices. Where no device is fitted, the terminals are bridged with a short jumper so the control sees a complete loop. The meaning given at the top of this page is that a required jumper or link is missing or disconnected, which puts the boiler into a soft lockout. Confirm that meaning against the manual for your unit, because wiring layouts differ between Laars models and control generations.

What that means in your home is straightforward. The control will not light the burner while that loop is open, so radiators, baseboard convectors or in-floor loops slowly cool down. If your domestic hot water comes from an indirect tank heated by the boiler, the hot water runs out as well, usually within a few draws. A soft lockout is generally one the control can clear on its own once the condition is corrected, unlike a hard lockout that needs a deliberate manual reset. If the jumper or link is genuinely missing, though, nothing will clear it and the code simply returns.

E42 is not in itself a sign of a gas leak or a combustion problem. It is a wiring and control-logic problem. That does not make it something to ignore or work around. A jumper is sometimes sitting exactly where a safety device used to be wired, or where one should be wired now. The right question on any E42 call is why the circuit is open, never simply how to close it.

  • The display shows E42 and the burner never lights, even though the thermostat is calling for heat.
  • The house is cooling slowly and radiators, baseboards or floors feel lukewarm or cold.
  • Hot water from an indirect tank is running out or never fully recovers.
  • The circulator pump may run briefly or not at all, depending on how your system is wired.
  • The code appeared shortly after someone worked on or near the system: a new thermostat, a zone controller, a new tank, or another trade working in the mechanical room.
  • The code comes and goes on its own, which usually points to a loose connection rather than a jumper that is missing outright.

Laars Boiler Error Code E42: Likely Causes, Most Common First

1. Wiring disturbed during other work. This is the cause we run into most often. A thermostat swap, a zone controller upgrade, an indirect tank install, or even an unrelated trade working in a tight mechanical closet can pull a jumper loose, remove it on purpose and forget to replace it, or remove it for a new device that was then never wired in. If E42 appeared within days of any work near the boiler, that is the first place we look.

2. A loose or corroded terminal. Field-wiring terminals carry very little current and depend on a firm, clean connection. Years of heat cycling, vibration from the circulator and damp basement or crawl-space air can loosen a screw terminal or corrode the end of a wire until the loop opens intermittently. This is the classic cause of an E42 that clears for a few hours and then comes back.

3. An external device wired into the link has opened. On some installations the factory jumper was replaced by the contacts of another device, for example an external high limit, a low-water cutoff, a flow or pressure device, a condensate overflow switch, or the end switch on a zone panel. If that device opens, or fails, the control can read the link as broken. Which devices are wired where depends entirely on how your system was installed, so this has to be traced with a meter rather than guessed.

4. A damaged wire or connector. A cable pinched behind a panel during a previous repair, a connector left half-seated, or rodent damage in a crawl space or garage can all break the loop. These faults are often intermittent at first and then become permanent.

5. A control or harness fault. This is less common. A damaged connector on the control board, or a fault inside the control itself, can produce a reading that does not match the actual wiring. It is confirmed by measurement and never assumed, because a control board is one of the more expensive parts on a boiler and replacing it on a hunch rarely fixes a wiring problem.

The table below lines each cause up with what you might notice, the only checks that are safe for an owner, and the step that needs a licensed technician.

Likely causeWhat you might noticeOwner-safe checkLicensed technician step
Jumper removed or not replaced after other workCode appeared right after a thermostat, zone control or tank changeWrite down what work was done and when, and tell the technicianTrace the field wiring, identify what belongs on those terminals and restore it correctly
Loose or corroded terminalCode comes and goes, sometimes with vibration or temperature changesLook only from outside the cabinet; do not touch wiring or open coversRemake and clean the connection, check for corrosion, test under full operation
External safety or interlock device has openedCode stays on; may coincide with low system pressure, water near the boiler or a condensate problemNote the pressure gauge reading and look for water or a kinked visible condensate lineTest the device, find out why it opened and repair the underlying condition
Damaged wire or connectorCode after renovation, rodent activity or a previous repairReport any chewed or pinched cable you can see without opening anythingReplace the damaged section and verify continuity end to end
Control or harness faultWiring tests correct but the code remainsNothing beyond power, thermostat and one permitted resetMeasure inputs at the control, confirm the fault, then quote in writing before replacing parts

Can I Reset a Laars Boiler With E42, and What Is Safe to Check?

You can work through a short list of checks that need no tools and no access behind any cover. Anything beyond that is technician work, and in BC that is not a matter of preference: gas appliances and the controls on them are serviced by licensed gas fitters, and most electrical work is restricted to licensed trades. The checks below are the whole of the owner’s job.

  • Power: confirm the boiler’s service switch is on and the breaker feeding it has not tripped. If the breaker trips a second time, leave it off and call.
  • Gas supply: confirm the manual gas shut-off valve to the boiler is in the open position. Do not operate valves you are unsure about.
  • Thermostat: confirm it is set to heat and set above the current room temperature, and replace its batteries if it uses them.
  • One reset only: if the owner manual allows a reset for this condition, do it once. If E42 returns, stop. Repeated resets will not restore a missing link and can mask a real fault.
  • Venting: outside, check that the intake and exhaust terminals are clear of leaves, nests, snow or anything stacked against them.
  • Condensate: if the condensate line is visible, look for a kink, a hose that has come off, or water pooling under the boiler. Look, but do not dismantle anything.
  • Make notes: when the code first appeared, any recent work near the boiler, and whether it comes and goes. Those three facts shorten the diagnosis more than anything else.

When Laars Boiler Error Code E42 Becomes a Licensed Call

Do not remove covers, touch the terminal strip, or try to add a jumper wire, even if you find instructions online that make it look simple. A jumper closes a circuit without asking why it was open. If a low-water cutoff or a limit was wired into that loop, jumpering it removes a safety that exists to stop the boiler firing without water or running too hot. Do not keep power-cycling the boiler either, and do not ask whoever disturbed the wiring to just put a wire back unless they are licensed to work on gas appliance controls.

It becomes a licensed call as soon as any of these apply: E42 returns after one permitted reset; it appeared after any work on or near the system; it comes and goes; you see water, scorch marks or a burning smell near the boiler; the system pressure looks wrong compared with what it normally reads; or any other fault appears on the display alongside it. At that point the next step is a technician with a meter, not another reset.

Gas and carbon monoxide safety comes first. If you smell gas, or a carbon monoxide alarm sounds, do not reset the boiler and do not operate light switches or appliances. Get everyone out of the home, then call FortisBC or 911 from outside. Every home with a gas boiler should have working CO alarms near the sleeping areas and on each level. E42 is a wiring fault, but a boiler that has been tampered with to clear a code is exactly where combustion and safety problems go unnoticed.

How Our Laars Boiler E42 Repair Visit Works

When you call (604) 473-9690 we book a diagnostic visit with one of our own licensed gas fitters. We offer same-day service where we can, depending on the day’s schedule and where you are in Metro Vancouver. We tell you honestly what the earliest real slot is and we never promise an arrival window we cannot keep. Cold snaps are our busiest weeks, so calling early in the day helps.

  • Step 1, the conversation: we ask what the display shows, when it started, and what work has been done near the boiler. With E42, recent work is the single most useful clue.
  • Step 2, a safe start: we check for gas odour, ask about CO alarm activity, and look over the venting, condensate line and system pressure before we touch the control.
  • Step 3, trace the field wiring: with the right meter we check continuity and voltage across the terminals involved, identify what is supposed to be wired there, and compare the installation with the manual for your unit.
  • Step 4, find out why the link is open: a missing jumper, a loose or corroded terminal, a damaged wire, or an external device that has opened for its own reason. If a safety device opened, we find the cause rather than just restoring the circuit.
  • Step 5, a written quote: if the fix goes beyond the diagnosis, such as replacing a switch, a wiring section or a control part, you get a written quote before any further work starts. The parts most often involved are terminals and wiring, external switches and interlocks, and less often the control board or its harness.
  • Step 6, repair and test the safeties: after the repair we run the boiler through complete heating cycles and confirm that the limits, low-water protection where fitted, flame proving and venting all behave as they should.
  • Step 7, explain and record: we show you what was wrong and leave a written record of what we found and did, which is useful for future service and if you ever need to deal with the manufacturer directly.

Repair or Replace an Older Laars Boiler, and Who Services It Near Me

E42 on its own is rarely a reason to replace a boiler. A missing jumper or a loose terminal is usually a modest repair, and an external switch is a component, not the boiler. The replacement conversation starts only when E42 is one of several problems on an older unit. The factors we weigh with you are the condition of the heat exchanger (corrosion, leaks or signs of overheating are the most serious age-related findings), the state of the system water, whether parts for an older control generation are still readily available, how many significant repairs the boiler has needed in recent seasons, and how long you plan to stay in the home. Metro Vancouver water is soft, so older hydronic systems here suffer from sludge and corrosion rather than limescale, and dirty system water shortens the life of any boiler, old or new. If replacement makes sense, we quote the boiler, venting, piping changes, system cleaning and the gas permit in writing; if repair makes sense, we say so plainly. Cost is always described in a written quote, never guessed over the phone.

BC Wide Home Services is an independent contractor licensed by Technical Safety BC, gas contractor licence LGA0090068 and Class B gas licence CGA0028029, serving Metro Vancouver from Burnaby since 1999. We are not a factory dealer or warranty centre for any brand. Work that needs a gas permit is permitted and inspected as BC requires, and our technicians are our own licensed staff. Boiler and hydronic brands we service include Laars, Navien, Bosch, Rinnai, Noritz and A. O. Smith, and we give the same honest diagnosis whatever the badge says.

We cover Laars boiler E42 calls across Greater Vancouver. Housing stock varies, and so do the causes we tend to find, so here is what we commonly see by area, in general terms.

  • Vancouver: many older houses have had their boiler rooms added to by several trades over the decades, and layered wiring from past upgrades is fertile ground for a disturbed jumper.
  • Burnaby and New Westminster: a mix of older detached homes, character houses and townhouse strata, where boilers often sit in tight closets that other trades also need to reach.
  • Surrey, Delta and Langley: many newer subdivisions and townhome complexes with radiant floor heating, where the boiler often shares wiring with zone panels and indirect tanks.
  • Richmond: low-lying ground means some garage and crawl-space installations live in damp air, which can speed up terminal corrosion.
  • Coquitlam and the Tri-Cities (Coquitlam, Port Coquitlam and Port Moody): a broad mix of detached homes and strata townhouses, many with hydronic controls upgraded over time.
  • The North Shore (North Vancouver and West Vancouver): hillside homes where outdoor vent terminals can collect leaves and needles, worth checking before any visit.
  • Strata homes anywhere: tell us about access rules and whether the boiler is yours or common property, since some stratas need notice before a technician enters a mechanical room.

More questions homeowners ask

What does Laars boiler error code E42 mean?

It means a required jumper or link in the boiler’s wiring is missing or disconnected, and the control has gone into a soft lockout. The boiler will not fire until that circuit is properly restored. Confirm the meaning against the manual for your unit, since wiring layouts vary between Laars models.

Can I reset Laars boiler error code E42 myself?

Only once, and only if the owner manual allows a reset for this condition. If E42 comes back, the link is still open and resetting again will not fix it. Call a licensed technician rather than cycling the power over and over.

Is it safe to run my Laars boiler with E42 showing?

The control will not normally fire the burner while E42 is active, so the boiler cannot heat properly anyway. Never bypass the code with a homemade jumper, because that circuit may carry a safety device such as a low-water cutoff. If you smell gas or a CO alarm sounds, leave the home and call FortisBC or 911 from outside.

Can I put the jumper wire back in on my Laars boiler?

No. Opening the control area and working on the wiring terminals of a gas appliance is technician work in BC, and adding a jumper without knowing why it was removed can defeat a safety device. A licensed gas fitter will confirm what belongs on those terminals and restore it correctly.

Why did E42 show up after my thermostat was replaced?

Thermostat, zone controller and tank installs are the most common reason a jumper ends up removed or a terminal is left loose. The new device may need different terminals, or a link the boiler expects may not have been put back. A technician can trace the wiring and correct it, often in a single visit.

Who repairs Laars boiler error code E42 near me in Greater Vancouver?

BC Wide Home Services, an independent TSBC-licensed gas contractor based in Burnaby, services Laars boilers across Vancouver, Burnaby, Surrey, Richmond, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We offer same-day visits where we can and give a written quote before any work beyond the diagnosis. Call (604) 473-9690.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote