Lennox boiler error code 125 means the boiler has detected no circulation, or too little, in its primary circuit and has usually stopped firing as a no-flow safety trip (confirm the exact meaning against the manual for your unit). The usual causes are trapped air, low system pressure, a stuck or failed circulator pump, a closed valve or sludge restricting flow. Check power, the pressure gauge and the thermostat, reset once only if the manual allows it, then call (604) 473-9690 for a licensed diagnosis.
If your Lennox boiler is showing 125 (Circulation fault (primary circuit)), here’s exactly what it means and what to do. This guide is part of our full Lennox boiler error code list.
Severity: Needs attention.
What 125 means on a Lennox boiler
No or insufficient circulation detected in the primary circuit, often a no-flow safety trip.
Common causes
- Failed or stuck pump
- Air lock in the primary circuit
- Low pressure
- Blocked/closed valves
What you can safely check first
- Check the pressure gauge and top up if you know how
- Bleed trapped air
- Persistent circulation faults require a technician to check the pump
Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.
When to call a technician
This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Lennox boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.
BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.
Lennox boiler repair across Greater Vancouver
If a Lennox boiler showing 125 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.
Related Lennox boiler codes
- Lennox boiler 10 — External probe / sensor cable fault
- Lennox boiler 12 — Water flow switch open
- Lennox boiler 13 — Water flow switch closed
- Lennox boiler 18 — Gas valve fault
- Lennox boiler 19 — Automatic water refill enabled
- Lennox boiler 20 — Max water refill reached / Central Heating Flow or Flue NTC fault
Frequently asked questions
Is 125 on a Lennox boiler serious?
It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs Lennox boilers 7 days a week across Greater Vancouver.
How do I reset a Lennox boiler after 125?
You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.
What does Lennox boiler error code 125 mean for your heat and hot water?
In plain terms, code 125 is the boiler protecting itself. A boiler can only fire safely when water is moving through its heat exchanger. If the control decides that water is not circulating through the primary circuit, or is moving too slowly, it shuts the burner down rather than let the heat exchanger overheat. Depending on the model, the control may judge circulation from a flow or pressure device, or from how quickly the water temperature inside the boiler climbs compared with the water coming back from the house. The exact method is described in the installation manual, so confirm against the manual for your unit before relying on any single explanation.
For you, that usually means the boiler has stopped making heat. Radiators, baseboard convectors or in-floor radiant loops go lukewarm and then cold. If the boiler also heats your domestic hot water, through an indirect tank or a built-in hot water section, hot water can be affected too, although on some systems hot water keeps working while the space heating side is at fault. It depends on how your system is piped, which is one of the first things we look at on site.
Is it dangerous? The trip itself is a safety device doing its job. What makes it a concern is the reason behind it. A seized pump, a heat exchanger choked with sludge or a system that keeps losing pressure will not fix itself, and pushing a boiler repeatedly through no-flow conditions stresses the heat exchanger and the pump seals. Treat 125 as a stop sign, not a nuisance light.
These are the symptoms owners usually describe to us when they call about this code:
- Rooms cooling down even though the thermostat is calling for heat
- Radiators hot at the top and cold at the bottom, or hot near the boiler and cold at the far end of the house
- Gurgling, rushing or trickling sounds in the pipes, which usually points to air in the system
- A pressure gauge reading lower than where it normally sits, or a needle that creeps down over several days
- A hum or buzz from the pump area with no sound of water moving
- Water spots under the boiler, at the relief valve discharge pipe or at a radiator valve
- The boiler firing briefly, shutting off, and showing the code again
- Lukewarm or no hot water at the taps on systems where the boiler also makes domestic hot water
Lennox boiler error code 125: what we check first, cause by cause
These are the causes we find most often behind a primary-circuit circulation fault, listed from most common to least common in the homes we work in. Your boiler can have more than one at the same time; low pressure and trapped air, for example, very often travel together because air gets in wherever water gets out.
The order matters because it is the order a good technician tests in. Going straight to a new pump without checking pressure, air and valve positions can mean fitting a perfectly good part into a system that still cannot circulate, and the code comes straight back. On a correct visit you should see pressure and flow confirmed before any part is condemned.
| Likely cause (most common first) | What is going on | Owner-safe check | When it becomes a licensed call |
|---|---|---|---|
| 1. Air trapped in the primary circuit | Air pockets collect at high points, at the pump or inside the heat exchanger and break the flow of water. Common after any work on the system or when an automatic air vent stops venting. | Listen for gurgling. Bleed radiators only if your manual describes it for your system and you have done it before, and watch the pressure gauge as you go. | Air that keeps coming back, or an air lock at the boiler or pump that bleeding the radiators does not clear. |
| 2. Low system pressure | A hydronic system is sealed and pressurized. With too little pressure the pump cannot move water properly, and some controls read the result as no flow. | Read the gauge and compare it with the range in the manual or the range your installer marked. Top up only if you know the procedure for your system. | Pressure that drops again after a top-up, which means a leak, a weeping relief valve or an expansion tank problem. |
| 3. Circulator pump stuck or failed | Pumps can seize after sitting idle all summer, foul with sludge or fail electrically. The motor may hum without moving any water. | Note whether you hear the pump running and whether the pipes on either side of the boiler are warming. Do not open, tap or loosen the pump. | Always. Freeing, testing or replacing a pump means isolating power and water and is technician work. |
| 4. A closed or partly closed valve | Isolation valves left closed after service, a zone valve stuck shut or a mixing valve that has seized will stop flow through the circuit. | Note any valve handle that was moved recently, but do not force or reposition valves you do not understand. | A zone valve or mixing valve that will not open, or any valve on the boiler itself. |
| 5. Sludge or magnetite restricting flow | In Metro Vancouver’s soft water, iron and steel in the system corrode slowly and form black sludge that settles in strainers, the pump and narrow heat exchanger passages. | If a radiator has been bled recently, note whether the water looked dark or black. That is useful information for the technician. | Sludge needs a professional clean and flush, fresh inhibitor and usually a magnetic dirt separator, done with the boiler isolated. |
| 6. Sensor, flow device, wiring or control fault | Less often, water is moving properly but the part that reports it, its wiring or the control board misreads the situation. | None beyond confirming the power is on. Never jumper, bypass or unplug anything. | Always. This is electrical diagnosis with meters inside the boiler cabinet. |
| 7. A frozen section of pipe | Rare in our mild climate, but piping in an unheated garage, crawlspace or exterior wall can freeze in a hard cold snap and block the loop. | Think about whether a cold area of the house lost heat first. Never use an open flame or heat gun on pipes. | Any suspected frozen or split pipe. |
Can I reset Lennox boiler error code 125 myself? Owner-safe checks and where to stop
You can work through a short list of checks that need no tools and no panels removed. Everything inside the boiler cabinet, the gas train, the burner and the control wiring is licensed work in BC, and gas work in particular is restricted to licensed gas fitters. Here is what is safe for an owner, in this order:
Why only one reset? Every reset asks the boiler to try firing into the same no-flow condition. If the pump is seized or the heat exchanger is clogged, repeated attempts can overheat parts of the heat exchanger and dry-run the pump seals, turning a pump repair into a much larger job. A single reset tells us whether the fault was a one-off. Repeated resets only hide the evidence a technician needs.
Topping up pressure and bleeding radiators are tasks many owners do, and they are mentioned earlier on this page, but only do them if your manual describes the procedure for your system and you have done it before. Hydronic water can be scalding hot, a fill valve left open can overfill the system until the relief valve discharges, and an overfilled system can create a second problem on top of the first.
Gas and carbon monoxide safety: if you smell gas (a rotten egg or sulphur smell) or your carbon monoxide alarm sounds, do not reset anything and do not operate light switches. Get everyone out of the house and call FortisBC’s emergency line or 911 from outside. A circulation fault is not a gas leak in itself, but every home with a gas boiler should have working CO alarms near sleeping areas and on each level, and a boiler problem is a good moment to test them.
- Power: confirm the boiler’s service switch is on and the breaker has not tripped. If the breaker has tripped, reset it once; if it trips again, leave it off and call.
- Gas supply: confirm the manual gas shutoff valve to the boiler is open, with the handle in line with the pipe. Do not touch any other gas fittings.
- Thermostat: make sure it is set to heat and set a few degrees above the current room temperature, and replace its batteries if it uses them.
- Pressure gauge: read it, write the reading down and compare it with the range in your manual or the range your installer marked.
- Venting: if the boiler vents through an outside wall or the roof, check from outside that the intake and exhaust terminals are clear of snow, leaves, nests or anything stored against them.
- Condensate drain: on a condensing boiler, look at the visible condensate line and trap for a kink, a disconnected hose or a pool of water. Do not take the trap apart.
- Reset: if the owner manual says this code can be reset by the user, reset it once. If 125 returns, stop and call a licensed technician. Do not keep cycling the power.
How our Lennox boiler error code 125 repair visit works, step by step
This is what a correct diagnostic visit looks like, and what you should see in writing before any repair goes ahead. The point is to prove where the flow is being lost before anything is replaced.
Parts most often involved, in general terms: the circulator pump or its cartridge, automatic air vents, the expansion tank, the pressure relief valve, the fill valve, zone valves or their actuators, strainers and filters, and less often a flow or pressure sensing device or the control board. A control board is one of the more expensive parts on a boiler, which is exactly why it should be the last thing condemned, not the first. Exact replacement parts depend on your model, so confirm against the manual for your unit or with the technician.
When sludge is the root cause, a new pump on its own is not a fix. A proper job cleans the system with a suitable hydronic cleaner, flushes it, refills it with inhibitor and usually adds a magnetic dirt separator so the new pump is not sitting in the same black water a year later. If sludge is found, ask for that cleaning to be itemized in the written quote.
- Step 1, the call: we ask for the code, what you have already checked, the pressure reading, whether hot water is affected and roughly how old the boiler is. We book same-day where we can; when the schedule is full we tell you so honestly and give you the earliest real appointment rather than a promised arrival window.
- Step 2, safety on arrival: the technician checks for gas odour and carbon monoxide, confirms the venting is intact and connected, and reviews the boiler’s fault history where the control stores it.
- Step 3, pressure and air: system pressure is confirmed on the boiler gauge and, where needed, a separate test gauge, because boiler gauges can stick. Air is checked at the boiler, the pump, the air vents and the high points of the system.
- Step 4, the flow path: every valve in the primary circuit is checked for position, zone valves and any mixing valve are tested through their full travel, and strainers or filters are opened and inspected for sludge.
- Step 5, the pump: the circulator is tested electrically with a meter for supply voltage and current draw, and mechanically for whether it is actually turning and moving water. A pump that hums but does not move water is identified at this step.
- Step 6, sensing and controls: if the water side checks out, the flow or pressure device, the temperature sensors, the wiring and the connectors are tested against manufacturer-published values, and only then is the control board considered.
- Step 7, written findings and quote: you get the cause, the recommended fix and a written quote before any work beyond the diagnosis. Nothing is replaced without your approval.
- Step 8, repair and proof: after the repair the system is refilled and purged of air, pressure is set to the manufacturer’s range for your system, and the boiler is run through full heating cycles. The safeties are tested, including the no-flow protection itself, and combustion is checked wherever the work touched the burner side.
Should I repair or replace an older Lennox boiler after code 125?
Most code 125 calls end in a repair, not a replacement. A pump, air vent, expansion tank or valve is a normal maintenance-level repair on a boiler that is otherwise sound. Replacement enters the conversation when the circulation fault turns out to be a symptom of something larger, and the table below shows how we weigh it on site.
If replacement is the right call, the circulation fault is still useful information. It tells us the new boiler needs clean system water, a pump sized correctly for your piping and proper air elimination from the first day. We size a replacement from a room-by-room heat loss calculation, not from the old boiler’s nameplate, and options can include a new condensing boiler with an indirect hot water tank or a combi boiler from one of the brands we service. Either way you get a written quote listing the equipment, the permit, the venting, any piping changes and the system cleaning, and we do not quote figures over the phone without seeing the job.
We will tell you plainly when a repair is the sensible choice. Replacing a sound boiler because of a failed pump is not good advice, and we would rather keep a working boiler running safely than sell you equipment you do not need.
| What we find on site | Points toward repair | Points toward replacement |
|---|---|---|
| Boiler age and history | A mid-life boiler with a good service record and a first circulation fault | A boiler near the end of its expected service life with several major repairs already behind it |
| Heat exchanger condition | Clean passages, no leaks and no signs of overheating damage | A leaking, cracked or badly fouled heat exchanger, or damage from repeated no-flow overheating |
| System water | Clear or lightly discoloured water that cleans up with a flush | Heavy sludge returning soon after cleaning, pointing to ongoing corrosion in old piping or radiators |
| Parts availability | Pump, sensors and controls readily available for your model | Key controls discontinued or on long back-order, leaving the house without heat for an extended period |
| Your plans for the home | Staying put and happy with how the home heats | Planning a renovation, adding zones or wanting more hot water capacity at the same time |
Lennox boiler error code 125 repair near you in Greater Vancouver
BC Wide Home Services Ltd is an independent TSBC-licensed gas contractor based in Burnaby, serving Metro Vancouver homeowners since 1999. We are not a Lennox dealer or an authorized warranty centre; we are the licensed independent contractor you call when the boiler stops. Our Technical Safety BC gas contractor licence is LGA0090068 and our Class B gas licence is CGA0028029, and boiler diagnosis and repair are done by our own licensed gas fitters.
Primary-circuit circulation faults look a little different across the region because the housing stock is different. These are general patterns we see, not rules for any particular house:
We also work in townhouses and strata homes that have their own boilers. In a strata building, check with your strata council or property manager before any work that affects shared venting or common property, and keep a copy of the paperwork for their records.
Brands we service for boilers and hydronic systems include Lennox, IBC, Viessmann, Navien, Bosch, Rinnai, Weil-McLain and Buderus. We name them as brands we service, not brands we are certified by, and we treat every brand the same way: diagnose first, quote in writing, then repair.
What you should see from us in writing: our licence numbers on the paperwork, a written quote before any work beyond the diagnosis, a gas permit and inspection wherever the work requires one (through Technical Safety BC, or through the City of Vancouver for homes inside the city), and a record of what was tested and what was replaced. Call (604) 473-9690 for a Lennox boiler error code 125 diagnosis; we come same-day where we can, and we tell you honestly when we cannot.
- Vancouver: many older homes run hydronic heat through cast-iron radiators or long-standing steel piping, often converted to a modern boiler. Old iron and steel in soft water is a common source of the sludge that blocks circulation.
- Burnaby and New Westminster: a mix of older detached homes, townhouses and heritage houses, where long pipe runs and earlier renovations can leave air traps at high points.
- Surrey, Langley and Delta: many newer homes and additions use in-floor radiant loops, where a stuck mixing valve or zone valve, or air in a long loop, can show up as a circulation fault.
- Richmond: slab-on-grade homes with radiant floors are common, so access to the manifolds and the condition of the loops matter to the diagnosis.
- Coquitlam, Port Coquitlam and Port Moody (the Tri-Cities): hillside and multi-level homes where several zones and longer runs make air elimination and pump sizing important.
- The North Shore (North Vancouver and West Vancouver): larger multi-zone hillside homes, often with boilers in tight mechanical rooms, where thorough purging after any work is essential.
More questions homeowners ask
What does Lennox boiler error code 125 mean?
It means the boiler has detected no circulation, or too little, in its primary circuit, which is usually treated as a no-flow safety trip that stops the burner. Confirm the exact meaning against the manual for your unit. The common causes are trapped air, low system pressure, a stuck or failed pump, a closed valve or sludge restricting flow.
Can I reset Lennox boiler code 125?
Once, and only if your owner manual says the code can be reset by the user. If 125 comes back, stop resetting and call a licensed technician, because repeated attempts can overheat the heat exchanger and damage the pump. Check the power, the gas valve, the thermostat and the pressure gauge before that single reset.
Is it safe to run my Lennox boiler with error code 125?
No. The boiler has shut down because it cannot confirm that water is moving, and forcing it through repeated resets risks damaging the heat exchanger and the pump. Leave it off and book a diagnosis. If you smell gas or a carbon monoxide alarm sounds, leave the house and call FortisBC or 911 from outside.
Why does my Lennox boiler keep showing code 125 after I top up the pressure?
Because the pressure is leaking away again or was never the root cause. A system that needs regular topping up has a leak, a weeping relief valve or a failing expansion tank, and the fresh water brings in air that can stop the pump from circulating. A licensed technician needs to find where the pressure is going and check the pump and valves.
How long does a Lennox boiler error code 125 repair take?
Many circulation faults are diagnosed and repaired in a single visit when the part is on the truck, such as an air vent, a valve or a common pump. Sludge cleaning, expansion tank work or parts that have to be ordered take longer. You get a written quote and a realistic timeline before any work starts.
Is there Lennox boiler repair near me in Greater Vancouver?
Yes. BC Wide is an independent TSBC-licensed contractor serving Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We are not a Lennox dealer or warranty centre, and we service the brand as an independent contractor. Call (604) 473-9690; we come same-day where we can.
- Lennox furnace g61mpv error codes
- Lennox furnace error code 225
- Goodman furnace error codes 6 blinks
- Boiler error message f28
- Miller furnace error codes
- Kelvinator furnace error codes
- Lennox furnace error code 270
- Airquest furnace error codes
- Heil furnace error code 4
- John Wood Water Heater Error Codes & Troubleshooting in Greater Vancouver
Frequently asked questions
How often should a boiler be serviced?
How much does a new boiler cost in Vancouver?
How long does a boiler last?
My boiler is making a banging or kettling noise. Is that dangerous?
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Should I repair or replace my old boiler?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


