Lennox boiler error code 134 means the gas valve was open for the allowed time without gas being detected or combustion established, so the boiler closed the valve and locked out. Confirm that meaning against the manual for your unit. Expect no heat, and possibly no hot water. Check that the power switch is on, the gas supply valve is open and the thermostat is calling, and reset once only if the manual allows it. If 134 returns, call a licensed gas technician at (604) 473-9690.
If your Lennox boiler is showing 134 (Gas valve open but no gas (elapsed time)), here’s exactly what it means and what to do. This guide is part of our full Lennox boiler error code list.
Severity: Critical — likely no heat / lockout.
What 134 means on a Lennox boiler
The gas valve was open for the allowed time without gas being detected/combustion established.
Common causes
- No or low gas supply
- Closed gas valve
- Gas valve or ignition fault
What you can safely check first
- Check that the gas supply and isolation valve are on
- If gas is confirmed on and it persists, call a licensed gas technician
Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.
When to call a technician
This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Lennox boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.
BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.
Lennox boiler repair across Greater Vancouver
If a Lennox boiler showing 134 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.
Related Lennox boiler codes
- Lennox boiler 10 — External probe / sensor cable fault
- Lennox boiler 12 — Water flow switch open
- Lennox boiler 13 — Water flow switch closed
- Lennox boiler 18 — Gas valve fault
- Lennox boiler 19 — Automatic water refill enabled
- Lennox boiler 20 — Max water refill reached / Central Heating Flow or Flue NTC fault
Frequently asked questions
Is 134 on a Lennox boiler serious?
It’s a lockout/safety code — the boiler has shut down and needs prompt diagnosis. BC Wide repairs Lennox boilers 7 days a week across Greater Vancouver.
How do I reset a Lennox boiler after 134?
You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.
Lennox Boiler Error Code 134: what it means for your heat, hot water and safety
In plain words, code 134 is the boiler telling you it tried to light and could not prove a flame. The meaning this page uses is the one stated above: the gas valve was open for the allowed time without gas being detected or combustion established. Confirm the exact wording against the manual for your unit, because display text can vary between control versions. What happens inside is simple. The control opens the gas valve, tries to ignite, and waits a short safety window for a flame signal. When that signal never arrives, it shuts the valve so unburned gas does not keep flowing, and once it runs out of permitted attempts it locks out and waits for someone to deal with it.
For your heat, that means radiators, baseboard convectors or in-floor loops slowly go cool because the burner never runs. You may still hear the circulator pump moving water around the system. That is normal and does not mean the boiler is half working; it is just moving water that is getting colder. For your hot water, if the boiler also feeds an indirect tank or is a combi-style design, hot water lasts only as long as the stored supply and then stops recovering.
For safety, the lockout itself is the boiler doing its job. It is designed to stop gas collecting in a combustion chamber that did not light. The risk comes from what caused it and from what people do next. Every reset sends another attempt, and another short release of gas, into a chamber that failed to light last time. That is why one reset is the limit, and only if your manual allows it.
Owners usually describe code 134 in one of these ways:
- The house is cold, the thermostat is calling for heat, and the boiler is silent apart from a click or the fan.
- The fan starts, there is a ticking or clicking sound for a few seconds, then nothing happens and 134 appears.
- The radiators or heated floors stay cool even though the pump seems to be running.
- Hot water runs out and does not come back, on homes where the boiler heats the water too.
- The code clears after a reset, the boiler runs for a day or two, then 134 comes back.
- It started right after gas work, a meter change, a power outage or the first real cold snap of the season.
- Other gas appliances in the home will not light either, which is a strong clue about the cause.
Lennox boiler error code 134 causes, most common first, with the checks you can safely do
Because the code describes a valve that opened without a flame being proven, the causes fall into three groups: gas is not reaching the burner, gas is reaching it but not lighting, or it is lighting but the control cannot see the flame. Here is how those break down on the jobs we attend across Greater Vancouver, roughly in order of how often we find them. This is a general guide, not a diagnosis of your particular unit.
- 1. The gas valve at the boiler is closed or only partly open. This is common after renovations, after other trades worked nearby, or after a previous service where the boiler was isolated and never fully reopened.
- 2. No gas is reaching the house. A utility shut-off, meter work, an account issue or work in the street can all stop the supply. If the range, fireplace or water heater will not light either, this is the likely group.
- 3. Gas pressure drops when other appliances run. Gas reaches the boiler, but not enough of it when the dryer, range, fireplace and water heater are all on. We see this most in older homes where the gas line was extended over the years for appliances it was never sized for.
- 4. Air in the gas line. After a meter swap, a new appliance hook-up or any gas line work, air can sit in the pipe until it is purged correctly by a licensed gas fitter.
- 5. An ignition fault. The igniter may be worn, cracked or out of position, or the ignition circuit may not be firing it.
- 6. A flame sensing fault. The burner lights, but the control does not register the flame, often because the flame sensor is dirty or oxidised or the ground path is poor. Our damp coastal air does not help with oxidation.
- 7. A gas valve or control output fault. The control may not be sending the signal to open, or the valve may not be opening when it receives it.
- 8. A combustion air, venting or condensate problem. On some installations a blocked intake or exhaust terminal, or a condensate trap that has backed up, can disturb ignition enough to cause a failed lighting attempt.
| Likely cause | What the owner can safely look at | When it becomes a licensed call |
|---|---|---|
| Gas valve at the boiler closed | The handle on the gas valve on the line into the boiler. On most quarter-turn valves, in line with the pipe is open and across the pipe is closed. If you did not close it, find out why before opening it. | If you are unsure which valve it is, if the valve is stiff or damaged, or if the code returns with the valve open |
| No gas to the house | Whether the range, fireplace or water heater will light. If nothing gas works, contact FortisBC. Never operate the meter valve yourself. | Once the utility confirms supply is restored and the boiler still shows 134 |
| Low gas pressure under load | Note whether 134 shows up when other gas appliances are running at the same time. | Always. Pressure testing with a manometer and any change to gas piping is licensed work. |
| Air in the gas line after gas work | Note the date and type of any recent gas work or meter change. | Always. Purging a gas line is licensed work only. |
| Ignition fault | Listen only. Ticking with no light, or no ticking at all, is useful information to pass on. | Always. Nothing behind the boiler cover is owner work. |
| Flame sensing fault | Nothing. Do not open the burner compartment to clean anything. | Always |
| Gas valve or control fault | Nothing beyond writing down what the display shows. | Always. These are tested with meters by a licensed technician. |
| Blocked intake, exhaust or condensate | From outside and from the ground, look at the vent terminals for leaves, nests or snow. Look at the visible condensate drain line for kinks or standing water. | If anything is blocked inside the vent, if the trap needs attention, or if the code persists after clearing an outside terminal |
Can I reset Lennox boiler error code 134, and when does it become a licensed gas call?
You can reset once, and only if the owner manual for your unit says a reset is permitted for this lockout. Before you do, run through the owner-safe list: power switch and breaker on, gas valve at the boiler open, thermostat set above room temperature and calling for heat, outside vent terminals clear, and the visible condensate drain free of kinks. If everything looks right, reset once and stay nearby to watch. If the boiler lights and runs a full cycle, write down the date and time and keep an eye on it. If 134 comes back, stop there.
Do not keep resetting, do not open any panel, and do not bypass, jumper or disconnect anything. Repeated resets can hide a real fault and can let gas build up in a chamber that is not lighting properly. In British Columbia, gas work is restricted to licensed gas fitters working for a licensed gas contractor, and that covers everything past the owner checks: testing gas pressure, purging lines, opening the gas train or burner compartment, and replacing igniters, flame sensors, gas valves or control boards. Most electrical work inside the boiler is also licensed work.
Code 134 becomes a licensed call when it returns after one reset, when gas is confirmed on and other appliances work fine, when it appears after any gas work, when it comes and goes over several days, or when you notice anything unusual around the boiler such as soot, scorch marks, water on the floor or a smell.
The safety line does not change for any boiler code:
- If you smell gas, a rotten egg or sulphur smell, do not reset the boiler and do not operate light switches or anything electrical. Leave the home and call FortisBC or 911 from outside.
- If a carbon monoxide alarm sounds, get everyone out, call 911 from outside, and do not go back in until you are told it is safe. Carbon monoxide has no smell, so the alarm is your only warning.
- Keep working CO alarms on every level of the home and near sleeping areas, and test them regularly.
- While you wait for service, do not use the gas range or oven to heat the house. Close off unused rooms and layer up instead.
How our Lennox boiler error code 134 repair visit works, step by step
BC Wide Home Services is an independent contractor licensed by Technical Safety BC, gas contractor licence LGA0090068 and Class B gas licence CGA0028029. Lennox is a brand we service; we are not a Lennox dealer or warranty centre. If your boiler is still under the manufacturer warranty, check the warranty paperwork before any repair so you know what it requires. Here is what a code 134 visit looks like from the first call to the final test.
- 1. The phone call. When you call (604) 473-9690 we ask what the display shows, when it started, whether other gas appliances work, whether anyone has done gas work lately, and whether there is any gas smell. If there is a smell, we tell you to leave and call FortisBC first. We book same-day where we can, depending on the schedule and where you are, and we never promise a guaranteed arrival window.
- 2. Safety first on arrival. Before touching the boiler, the technician checks the area for combustible gas and carbon monoxide.
- 3. Reading the history. We note the code, check any stored lockout history the control offers, and confirm the meaning against the manual for your unit.
- 4. Verifying the gas supply. With a manometer we measure inlet pressure with the boiler idle and again with other gas appliances running, then check burner pressure following the manufacturer procedure. This is where undersized lines and supply problems show up.
- 5. Watching the ignition sequence. We watch the boiler try to light, test the igniter, measure the flame signal with a meter, and inspect the flame sensor and the ground path.
- 6. Testing the valve and control. We confirm the control is sending the open signal and the gas valve is responding to it.
- 7. Checking venting, combustion air and condensate. Terminals, vent joints, the condensate trap and the drain line are inspected, because any of them can disturb ignition.
- 8. Written findings and quote. Before any work beyond the diagnosis, you get a written quote that names the cause we found, the part or work needed, and your options. Nothing proceeds until you approve it.
- 9. Repair and safety testing. After the repair we run the boiler through repeated ignition cycles, check combustion, leak-test any gas connection we disturbed, test the safety controls fitted to your boiler, and confirm heat is reaching the system.
| What you should see in writing | Why it matters |
|---|---|
| The cause we found, in plain words | So you know whether the fix addresses the real fault or only the symptom |
| Gas pressures recorded during the visit | Shows whether supply was checked properly, not assumed |
| Parts replaced, described in general terms | Gives you a service record for the next technician |
| Safeties tested and combustion checked | Confirms the boiler was proven safe, not just made to light |
| Permit details where the work requires one | Some gas work needs a permit and inspection in BC |
| Written quote before any work beyond diagnosis | You approve the scope and stay in control of the decision |
Repair or replace: what to do with an older Lennox boiler that keeps showing code 134
On its own, code 134 rarely means a boiler is finished. Most of the causes are supply problems or ignition and flame-sensing parts, and those are normal repairs. The parts most often involved, in general terms, are the igniter, the flame sensor, the gas valve, the control board and the condensate trap or drain. A control board and a gas valve are among the more expensive parts on a boiler, so ask for a written quote and a clear explanation of how the fault was confirmed before either one is replaced.
The replacement conversation starts when the 134 visit uncovers bigger problems. A corroded or leaking heat exchanger, parts that are discontinued or hard to source, repeated lockouts across several different components, or a boiler well into the later part of its service life can all change the answer. Here in Metro Vancouver, our soft water means hydronic systems tend to suffer from sludge and corrosion rather than limescale, so we also look at the condition of the water in the loop. Sludge does not cause code 134, but a heavily fouled system changes whether a big repair is worth it.
If you do replace, the job involves more than swapping the box. The gas line has to be checked to make sure it can supply the new boiler alongside your other appliances, the venting has to meet code and the manufacturer instructions, the system should be flushed and protected, and a gas permit and inspection apply. We service Lennox, Navien, Rinnai, Bosch, Noritz and Rheem among others, and we give neutral options because we are not tied to any manufacturer. The decision stays with you, backed by a written quote.
| Factor | Leans toward repair | Leans toward replacement |
|---|---|---|
| What caused the 134 | Gas supply, igniter, flame sensor or one clear failed part | Several components failing over a short period |
| Heat exchanger condition | Sound, with no leaks or heavy corrosion | Leaking, cracked or heavily corroded |
| Parts availability | Parts readily available | Parts discontinued or very slow to source |
| Repair history | First significant repair in years | Repeated lockouts and repeated service calls |
| System water | Reasonably clean loop | Heavy sludge needing major system work anyway |
| Your plans for the home | Selling soon or the boiler is otherwise healthy | Staying long term and the boiler is near the end of its life |
Lennox boiler error code 134 service near you across Greater Vancouver
We attend Lennox boiler lockouts across Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the rest of the Tri-Cities, the North Shore, New Westminster, Delta and Langley. Our base is in Burnaby and we have worked on Metro Vancouver heating systems since 1999. We do not serve every community in the Fraser Valley, so ask when you call if you are outside these areas.
Housing stock shapes how a code 134 job goes. In older parts of Vancouver and New Westminster, many homes have hydronic systems that have been updated more than once, with gas lines extended over the decades for new appliances. Those are the homes where we most often find pressure that drops when everything runs at once. In Burnaby, Coquitlam, Richmond and the newer parts of Surrey, many boilers sit in townhouses and strata buildings, with side-wall vents near balconies, shared mechanical rooms and gas meters that need the property manager to arrange access. On the North Shore, homes at higher elevations see more snow than the rest of the region, so blocked terminals turn up more often after a storm. In Delta and Langley we see a mix of newer subdivisions and older properties with longer gas runs.
Our climate matters too. The mild, wet coast means leaves, moss and nests build up around vent terminals in the fall, and damp air encourages oxidation on flame sensors and ignition parts. The first real cold snap of the season is when many 134 calls come in, because every gas appliance in the home is running at once and any weakness in supply or ignition shows up.
On permits, gas work across most of the region is permitted through Technical Safety BC, while the City of Vancouver issues its own gas permits. We handle whichever applies to your address, book the inspection where one is required, and note it on your paperwork.
More questions homeowners ask
What does Lennox boiler error code 134 mean?
It means the gas valve was open for the allowed time without gas being detected or combustion established, so the boiler shut the valve and locked out. Confirm the exact meaning against the manual for your unit. In practice it is a failed lighting attempt, and the cause can be gas supply, ignition or flame sensing.
Can I reset Lennox boiler error code 134 myself?
Yes, once, and only if the owner manual for your unit allows a reset for this lockout. First check that the power is on, the gas valve at the boiler is open, the thermostat is calling and the outside vent terminals are clear. If 134 returns after that single reset, stop and call a licensed gas technician rather than resetting again.
Is it safe to run my Lennox boiler after code 134 clears?
If it lights and runs normally after one permitted reset and there is no gas smell, it is reasonable to watch it, but the fault that caused the lockout may still be there. If the code comes back, intermittent or not, have it diagnosed. If you ever smell gas or a CO alarm sounds, leave and call FortisBC or 911 from outside.
Why did my Lennox boiler show code 134 after gas work or a meter change?
The most common reasons are a valve that was not fully reopened or air left in the gas line. Both stop gas from reaching the burner in time for the boiler to prove a flame. Purging the line and confirming pressure is licensed gas work, so call a licensed gas fitter rather than resetting repeatedly.
Can you fix Lennox boiler error code 134 same day in Greater Vancouver?
Same-day where we can. It depends on the day’s schedule, where you are in Metro Vancouver, and whether the part needed is on hand. We will tell you honestly when we can attend, and we never promise a guaranteed arrival window. Call (604) 473-9690 to check availability.
Does Lennox boiler error code 134 mean I need a new boiler?
Usually not. Most 134 faults trace back to the gas supply or to ignition and flame-sensing parts, which are normal repairs. Replacement only comes up if the visit finds bigger problems such as a failing heat exchanger, discontinued parts or repeated multi-part failures, and you get a written quote either way.
- Lennox furnace g61mpv error codes
- Lennox furnace error code 225
- Goodman furnace error codes 6 blinks
- Boiler error message f28
- Miller furnace error codes
- Kelvinator furnace error codes
- Lennox furnace error code 270
- Airquest furnace error codes
- Heil furnace error code 4
- John Wood Water Heater Error Codes & Troubleshooting in Greater Vancouver
Frequently asked questions
How often should a boiler be serviced?
How much does a new boiler cost in Vancouver?
How long does a boiler last?
My boiler is making a banging or kettling noise. Is that dangerous?
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Should I repair or replace my old boiler?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


