★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Lennox Boiler Code 20 — Max water refill reached / Central Heating Flow or Flue NTC fault | BC Wide

Boilers, Error Codes, Hvac

Lennox Boiler Code 20 — Max water refill reached / Central Heating Flow or Flue NTC fault | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Lennox Boiler Code 20 — Max water refill reached / Central Heating Flow or Flue NTC fault | BC Wide

Lennox Boiler Code 20 — Max water refill reached / Central Heating Flow or Flue NTC fault | BC Wide

Quick answer

Lennox boiler error code 20 means one of two things, depending on context: the boiler has reached its maximum number of automatic water refills, or a central-heating flow or flue NTC temperature sensor circuit is faulty (confirm against the manual for your unit). Either way the boiler has locked out to protect itself. Check for visible leaks, note the pressure gauge, reset once only if your manual allows it, then call a licensed gas technician. BC Wide services Lennox boilers across Greater Vancouver: (604) 473-9690.

If your Lennox boiler is showing 20 (Max water refill reached / Central Heating Flow or Flue NTC fault), here’s exactly what it means and what to do. This guide is part of our full Lennox boiler error code list.

Severity: Needs attention.

What 20 means on a Lennox boiler

Depending on context, the maximum number of automatic water refills has been reached, or an NTC temperature sensor (central-heating flow or flue) circuit is faulty.

Common causes

  • Repeated auto-refills due to a persistent leak
  • Faulty or disconnected flow/flue NTC sensor
  • Sensor wiring fault

What you can safely check first

  1. Check for visible leaks and watch the pressure gauge
  2. Sensor faults require a technician – do not attempt to replace sensors yourself

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Lennox boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Lennox boiler repair across Greater Vancouver

If a Lennox boiler showing 20 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Lennox boiler codes

Frequently asked questions

Is 20 on a Lennox boiler serious?

It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs Lennox boilers 7 days a week across Greater Vancouver.

How do I reset a Lennox boiler after 20?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Lennox Boiler Error Code 20: what it means for your heat, hot water and safety

In plain owner words, code 20 is the boiler telling you it has stopped trusting either its water supply or its temperature readings. On the refill side, a boiler with an automatic fill tops up the heating loop when the pressure drops. That should happen rarely. When it keeps happening, the control counts the refills and, once it reaches its limit, locks out rather than keep pouring fresh water into a system that is losing it somewhere. On the sensor side, the boiler relies on NTC thermistors to know how hot the water leaving the heat exchanger is and how hot the flue gases are. If one of those circuits reads something impossible, the control cannot safely fire the burner, so it shuts down.

What you notice depends on how your system is set up. Most owners describe some combination of the following.

The important point: code 20 is a protective lockout, not a gas leak warning. The boiler is doing its job by refusing to run. It is, however, a fault that keeps coming back until the cause is found, and on a gas appliance, a boiler that is reset over and over is a boiler being run outside the conditions its safeties expect. If you ever smell gas or your carbon monoxide alarm sounds, stop reading: leave the house, do not operate switches or the boiler on your way out, and call FortisBC or 911 from outside.

  • Radiators, baseboard convectors or in-floor heat going lukewarm, then cold
  • The display showing 20 with the burner off and the pump quiet or only running briefly
  • If your Lennox is a combi model, no hot water at the taps either, because the same burner makes your domestic hot water
  • The pressure gauge sitting lower than it normally does, or creeping back up after the boiler refills itself
  • Water marks, a damp tray, or a white or rusty crust under a valve, a fitting or the relief-valve discharge pipe
  • The code clearing after a reset, then returning hours or days later

Lennox boiler error code 20: likely causes, most common first

These are the causes we find most often behind this code, listed in the order we tend to find them on Greater Vancouver boilers. The owner-safe check in each row is the full extent of what a homeowner should do. Everything past that point involves gas controls, live wiring or pressurised hot water, and it belongs to a licensed technician.

Two of these deserve a closer word. On Metro Vancouver hydronic systems, the slow leak and the weeping relief valve are tied to how our water behaves. Our municipal water is soft, so we rarely see limescale inside heating loops. What we see instead is sludge and corrosion: magnetite and rust particles that circulate, settle in low spots and foul valves, air vents and sensor pockets. Every litre of fresh water an auto-fill adds brings in new dissolved oxygen, which feeds more corrosion, which makes more sludge. A boiler that has been quietly refilling itself for months has usually been speeding up its own wear, which is exactly why the control is designed to stop counting and lock out.

The sensor causes are less dramatic but just as real. An NTC thermistor changes its electrical resistance as its temperature changes. When a sensor fails or its connector corrodes, the control sees a reading that cannot belong to a working boiler and refuses to fire. A technician confirms this by measuring resistance at a known temperature and comparing it with the manufacturer-published chart for your model, not by swapping parts until the code clears.

What not to do: do not open the cabinet, unplug or replace sensors, jumper or bypass anything, cap a dripping relief valve, bleed radiators on a boiler that is already losing pressure, or keep resetting. If your owner manual describes a pressure top-up procedure, doing it once and writing down the reading is reasonable; doing it every day only feeds the leak. One reset, only if your manual permits it, is the limit.

Likely causeWhat is going onOwner-safe checkWhen it becomes a licensed call
1. Slow leak in the heating loopWater escapes from a radiator valve, a manifold, a fitting or a pipe; pressure drops and the auto-fill keeps topping up until it reaches its refill limitLook along visible piping, radiator valves and under the boiler for drips, stains or crust; write down the gauge reading morning and eveningWhen the gauge keeps falling or you find a wet fitting; hidden leaks in walls or slabs need isolation and pressure testing
2. Weeping pressure relief valveIf the expansion tank has lost its air charge, pressure spikes as the water heats and the relief valve dumps water, which the boiler then replacesSee whether the relief-valve discharge pipe is wet or dripping into its drain or bucketRight away; relief valves and expansion tanks are safety devices and are never adjusted, capped or recharged by an owner
3. Air vent or bleed point losing waterAutomatic air vents meant to release air can stick open and spit water, especially on systems carrying sludgeLook for damp marks or drips at vents on top of the boiler, on the pipework or at high pointsWhen a vent is wet; it is serviced or replaced with the system isolated and depressurised
4. Faulty central-heating flow NTC sensorThe thermistor on the heating flow reads out of range, so the control cannot judge water temperatureNote whether the code appeared with no sign of water loss, or after a power outage or surgeAlways; testing needs a meter, the manufacturer resistance chart and access inside the cabinet
5. Faulty flue NTC sensorThe sensor that monitors flue gas temperature reads open or shorted, so the boiler cannot confirm safe combustion conditionsConfirm the outside intake and exhaust terminal is clear of snow, leaves, debris or nestsAlways; the flue sensor is part of the combustion safety chain
6. Sensor wiring or connector faultA loose, corroded or chafed connection, often below an old drip, makes a good sensor look badLook, without opening any panel, for signs that water has run down the boiler casingAlways; the repair is inside the control compartment

How our Lennox boiler error code 20 repair visit works, step by step

Here is what a correct visit looks like when one of our licensed gas technicians arrives for a code 20. You are welcome to watch any part of it, and you will not be asked to approve a repair before you know exactly what it is and why.

Besides Lennox, the boiler and combi brands we service include Navien, Rinnai, Bosch, Noritz, Takagi, Rheem, Bradford White and A. O. Smith. We are an independent contractor, not a factory-authorized dealer or warranty centre for any of them, so if your boiler may still be under manufacturer warranty, check the warranty terms before booking a repair, and tell us so we can document the fault properly.

  • Step 1, the phone call. We ask what the display shows, whether the code clears after one reset, what the pressure gauge reads, whether you have heat and hot water, and whether you have seen water anywhere. We book same-day where we can; in a cold snap the schedule fills, and we tell you honestly if the earliest slot is the next day.
  • Step 2, safety first on arrival. Before anything else the technician checks for gas odour and combustion spillage around the boiler and its venting, and confirms there is a working carbon monoxide alarm nearby.
  • Step 3, read the history. Many boilers keep recent fault information. The technician reviews it alongside your account of when the code started to decide whether this is the refill branch or the sensor branch of code 20.
  • Step 4, the water side. With the system cool and safe, the technician checks the cold fill pressure, the expansion tank air charge, the relief valve, the auto-fill and every accessible fitting, valve and vent. If the loss is not visible, the loop is isolated and pressure-tested zone by zone until the leak is located.
  • Step 5, the sensor side. With the right meter, each NTC sensor and its wiring is tested against the manufacturer-published resistance values for your model, and connectors are inspected for corrosion, heat damage or water tracking.
  • Step 6, a written quote before any work beyond diagnosis. You get the cause in plain language, the repair options and a written quote. Nothing is replaced until you approve it.
  • Step 7, the repair and the safeties. In general terms, the parts most often involved are a sensor, a connector or harness section, a relief valve, an expansion tank, an air vent, or a leaking valve or fitting. Afterwards the technician refills and purges the loop, checks pressure cold and hot, confirms combustion, tests the safety controls and runs the boiler through a full heating call, plus a hot water draw on a combi.
  • Step 8, the paperwork. Your invoice names the cause, what was replaced, the readings that confirmed the fix, and anything worth watching, such as sludge in the loop or a valve near the end of its life.

Should I repair or replace an older Lennox boiler with code 20?

For most code 20 calls the honest answer is repair. A failed sensor, a corroded connector, a worn relief valve or an expansion tank that has lost its charge are normal service items, and replacing a whole boiler over one of them makes no sense. The decision only changes when code 20 turns out to be a symptom of something larger.

Replacement belongs in the conversation when the water loss traces back to the boiler itself, such as a leak inside the heat exchanger; when the system has run on fresh make-up water for so long that the heat exchanger is fouled and corroded; when parts for your particular model are hard to source; or when this repair would be one of several in a short span. A heat exchanger is one of the most expensive parts on any boiler, and on an older unit it often tips the decision.

On a sludged loop, a correct repair is often more than one part. Flushing the system, fitting or cleaning a dirt separator or magnetic filter where one makes sense, and dosing the water with a suitable inhibitor protect the new parts and the boiler from the same cycle starting again. We explain why each item is on the quote, and you can decline anything that is not essential to the fault.

If replacement does come up, we quote it in writing with the permit and inspection included, and we size the new gas boiler or combi from a heat-loss assessment rather than simply matching the old nameplate. We will not push replacement to clear a code that a proper repair fixes.

  • Repair usually makes sense: a single failed sensor or connector, a relief valve or expansion tank fault, an external leak at a valve or fitting, or a boiler that otherwise runs cleanly
  • Ask for a replacement quote alongside the repair quote: a leak inside the boiler, heavy corrosion inside the cabinet, parts that are difficult to source, or repeated lockouts across different faults
  • Plan the loop as well as the boiler: if the leak is in buried or in-slab piping, the repair plan for the piping matters as much as the boiler decision

Lennox boiler error code 20 service near me: Greater Vancouver coverage

We service Lennox boilers across Greater Vancouver from our Burnaby base, including Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the rest of the Tri-Cities, the North Shore, New Westminster, Delta and Langley. The housing stock varies a great deal across that area, and it shapes how a code 20 call usually unfolds.

In Vancouver and Burnaby we work on many older houses where a newer boiler has been connected to hydronic piping that was installed long before it. Mixed pipe materials and long-serving radiator valves are common places for slow leaks, and older loops tend to carry more sludge, so the refill branch of code 20 is the one we often chase there.

Older homes in New Westminster and on the North Shore can have heating runs hidden inside walls and floors, which makes pressure testing by zone the only sensible way to find a leak. Hillside lots can also put the venting terminal in awkward or sheltered spots, which matters when the flue sensor branch is involved.

In the Tri-Cities, Surrey, Richmond, Delta and Langley we see a wide range of homes, including newer houses and townhomes with in-floor radiant heat on manifolds, where a leaking manifold fitting or a tired expansion tank is a frequent trigger.

Strata townhomes and some low-rise buildings add a step. The boiler may be yours, but access, venting through shared walls and any work touching common property can need the strata’s approval. We help you sort that out before work begins so the repair is not held up halfway.

Our mild, wet coastal climate means boilers run long, gentle seasons rather than short, hard ones, so a slow leak can go unnoticed for months before the refill limit is reached. Heavy autumn rain and leaf fall make a fouled outside terminal more likely than snow here, though a snowfall can still bury a low-mounted terminal.

Who should fix Lennox boiler error code 20: licences, permits and what you should see in writing

In BC, work on gas appliances is restricted to licensed gas fitters working under a licensed gas contractor, and most electrical work inside the boiler is restricted too. That is not a formality: a code 20 repair can involve flue temperature sensing and combustion safety, the very systems that decide whether the boiler vents its exhaust safely.

BC Wide Home Services Ltd has served Metro Vancouver since 1999 as an independent Technical Safety BC licensed contractor, gas contractor licence LGA0090068 and Class B gas licence CGA0028029. The technician at your door is our own licensed gas fitter. Where the work needs a permit, such as a boiler replacement or a change to gas piping or venting, we pull it and arrange the inspection.

Before you approve any code 20 repair, from us or anyone else, you should see the following.

Call (604) 473-9690 to book a diagnosis. If you smell gas or a carbon monoxide alarm sounds at any point, leave first and call FortisBC or 911 from outside, then call us.

  • The cause named in plain language, with the branch identified: a refill fault or a sensor fault
  • A written quote listing parts and labour before any work beyond diagnosis begins
  • Confirmation of who holds the gas licence on the job and whether a permit applies
  • After the repair, the readings that show the fix worked: pressure cold and hot, sensor values and a combustion check
  • Notes on anything to keep an eye on, such as sludge, an ageing expansion tank or a valve close to the end of its life

More questions homeowners ask

What does error code 20 mean on a Lennox boiler?

Depending on context, it means either the boiler has reached its maximum number of automatic water refills, or a central-heating flow or flue NTC temperature sensor circuit is faulty. Confirm the meaning against the manual for your unit. In both cases the boiler has locked out to protect itself, and the cause needs to be found rather than reset away.

Can I reset Lennox boiler error code 20 myself?

Once, and only if your owner manual says a reset is allowed for this code. If the code comes back, stop resetting: on the refill branch each reset lets the boiler add more fresh water to a system that is losing it, and on the sensor branch the fault simply returns. At that point it is a call for a licensed technician.

Is it safe to run my Lennox boiler with code 20 showing?

The boiler will not fire while the code is active, which is the safe outcome. The risk comes from resetting it again and again to force it back on, which runs it outside the conditions its safeties expect and can mask a flue sensor problem. If you smell gas or a CO alarm sounds, leave and call FortisBC or 911 from outside.

Why does my Lennox boiler keep losing pressure and showing code 20?

Ongoing pressure loss almost always means water is leaving the system, through a leaking valve or fitting, a relief valve weeping because the expansion tank has lost its charge, an air vent spitting water, or occasionally a leak inside the boiler. The automatic fill keeps replacing that water until the control reaches its refill limit. A technician locates the loss by isolating and pressure-testing the loop rather than guessing.

How much does it cost to fix Lennox boiler code 20?

It depends entirely on which cause is behind it. A sensor, connector, relief valve or expansion tank is a routine repair, while a leak inside the boiler or in buried piping is a much larger job. We diagnose first and give you a written quote before any work beyond diagnosis.

Who fixes Lennox boilers near me in Greater Vancouver?

BC Wide services Lennox boilers across Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the Tri-Cities, the North Shore, New Westminster, Delta and Langley, with same-day visits where we can. We are an independent TSBC-licensed contractor, not a Lennox dealer or warranty centre. Call (604) 473-9690 to book.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote