★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Lennox Furnace Code DS1 & DS2 simultaneous fast flash — Normal heat call | BC Wide

Error Codes, Furnace, Hvac

Lennox Furnace Code DS1 & DS2 simultaneous fast flash — Normal heat call | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Lennox Furnace Code DS1 & DS2 simultaneous fast flash — Normal heat call | BC Wide

Lennox Furnace Code DS1 & DS2 simultaneous fast flash — Normal heat call | BC Wide

Quick answer

On a Lennox furnace, DS1 and DS2 fast-flashing together means a normal heat call: the thermostat has asked for heat and the control board is starting its heating sequence. It is a status signal, not a fault, so nothing needs repairing if warm air follows within a few minutes. Confirm against the manual for your unit. If the lights keep flashing but no heat arrives, check the thermostat, filter, gas valve handle and outdoor vent terminals, then call (604) 473-9690.

If your Lennox furnace is showing DS1 & DS2 simultaneous fast flash (Normal heat call), here’s exactly what it means and what to do. This guide is part of our full Lennox furnace error code list.

Severity: Status / informational.

What DS1 & DS2 simultaneous fast flash means on a Lennox furnace

Both LEDs fast-flashing together (3 Hz) is normal operation, signaled when a heating demand is initiated at the thermostat.

Common causes

  • Thermostat is calling for heat — normal operation

What you can safely check first

  1. No action needed; the furnace is responding to a heat call normally

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

If the simple checks above don’t clear the code, have it diagnosed by a licensed technician. Repeated lockouts on a Lennox furnace usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver furnaces since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Lennox furnace repair across Greater Vancouver

If a Lennox furnace showing DS1 & DS2 simultaneous fast flash won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast furnace repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Lennox furnace codes

Frequently asked questions

Is DS1 & DS2 simultaneous fast flash on a Lennox furnace serious?

It’s typically a status/informational code rather than a breakdown, but confirm against the symptoms. BC Wide repairs Lennox furnaces 7 days a week across Greater Vancouver.

How do I reset a Lennox furnace after DS1 & DS2 simultaneous fast flash?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Lennox furnace error code DS1 DS2 simultaneous fast flash: what it means for your heat, hot water and safety

In plain terms, the two small lights on the furnace control board are telling you the thermostat has asked for heat and the furnace has heard it. Lennox documents this pattern as normal operation at the start of a heating demand, so it is a status signal rather than an error. Confirm against the manual for your unit, because control boards vary across model generations and the wiring label inside the furnace door is the authority for your exact board.

Most owners only see this pattern because something else made them look at the furnace: the house felt cool, the furnace sounded different, or a smart thermostat showed an unusually long run time. The light pattern itself is good news. It tells you the board has power, the thermostat wiring is delivering a call, and the furnace is starting its normal sequence of venting, ignition and blower operation. What it does not tell you is whether that sequence finishes properly. That is the question that matters, and it is answered by what happens over the next few minutes, not by the lights alone.

What owners usually describe when they find this pattern:

  • Both lights flashing quickly together while the furnace starts up, and warm air follows: normal, nothing to do.
  • Both lights flashing together, the small venting fan is running, but no flame and no warm air after several minutes: the heat call is being received but the sequence is not completing.
  • Both lights flashing together, the furnace heats for a short time, shuts off, then starts again in a short loop: possible short cycling that is worth having checked.
  • Both lights flashing together but the house never reaches the set temperature: the furnace is working but may be airflow-restricted, losing heat through ductwork or struggling in a cold snap.
  • Both lights flashing together and you also smell gas or your carbon monoxide alarm is sounding: leave the house now and call from outside.

DS1 DS2 fast flash but no heat: likely causes, most common first

When the lights show a normal heat call but the house stays cold, the furnace is getting the request and something later in the sequence is not finishing, or the heat is not reaching the rooms. These are the causes we find most often on Greater Vancouver service calls, in rough order of how often we see them. If the lights change to a different pattern while you watch, write it down, look it up in the full Lennox code list, and confirm against the manual for your unit.

  • 1. Thermostat setting or schedule. The thermostat is calling but is set only slightly above room temperature, is following a schedule, or a smart thermostat is running a staged or heat-pump-first program on a dual-fuel system. Owner check: set heat mode, raise the setpoint a few degrees above room temperature and wait. Licensed call if the thermostat wiring or the control board is suspect.
  • 2. Dirty or collapsed air filter. A clogged filter starves the furnace of airflow, so it can overheat, shut the burners down on its high-temperature safety and restart, giving short bursts of heat. Owner check: replace the filter with the correct size, arrow pointing in the direction of airflow. Licensed call if the problem continues with a clean filter.
  • 3. Blocked intake or exhaust terminal. High-efficiency Lennox furnaces draw combustion air and vent through plastic pipes, often out a side wall or the roof. Snow, leaves, a wasp nest or a shrub grown over the terminal can stop the sequence. Owner check: look at the outdoor terminals and clear loose debris by hand without moving or pulling on the pipes. Licensed call if the pipes are cracked, sagging, disconnected or the terminal sits too close to a window, deck or neighbour.
  • 4. Condensate drain or trap blocked. Condensing furnaces make water as they run. If the trap, hose or condensate pump backs up, the furnace protects itself and will not run properly. Owner check: look for water around the furnace base, a kinked clear hose, or a condensate pump that is full or silent. Licensed call to clean or replace the trap, since it sits inside the cabinet.
  • 5. Gas supply valve closed or gas service interrupted. The manual gas valve beside the furnace may have been turned off during a renovation, or other gas appliances have also stopped working. Owner check: confirm the handle on the furnace gas valve is in line with the pipe, and see whether your gas range or water heater lights. Anything beyond the handle position is licensed gas work. A house-wide gas interruption is a matter for FortisBC.
  • 6. Ignition or flame sensing problems. The igniter is cracked or worn, or the flame sensor is coated and the board cannot prove the flame. Owner check: none beyond watching and noting what happens. This is a licensed call, because the sensor and igniter sit inside the burner compartment.
  • 7. Venting safety switch, gas valve or control board faults. Less common, and usually accompanied by a change in the light pattern. This is a licensed diagnosis with proper meters, never a parts-swapping exercise.
  • 8. Heat not reaching the rooms. The furnace runs correctly, but closed registers, disconnected ducts in a crawlspace or attic, or a failing blower motor send the warm air somewhere else. Owner check: open supply registers and return grilles and feel for airflow. Licensed call for duct repair or blower diagnosis.
What you noticeMost likely areaOwner-safe checkWhen it becomes a licensed call
Lights flashing together, warm air within a few minutesNormal heat callNone neededNot needed
Lights flashing together, venting fan runs, no flameVenting, condensate, gas supply or ignitionClear outdoor terminals, check the drain hose, confirm the gas valve handleIf heat does not start after those checks
Short bursts of heat, then shut-off, then restartAirflow, filter or high-temperature safetyReplace the filter, open registers and return grillesIf it continues with a clean filter
Furnace runs for long periods, house stays coolDuctwork, blower or sizingOpen registers, look for crushed flexible duct you can seeFor duct, blower or sizing assessment
Gas smell or CO alarm with any light patternPossible gas leak or combustion problemLeave the house and call from outsideImmediately, after FortisBC or 911

Can I reset a Lennox furnace showing DS1 DS2 fast flash? Owner-safe checks only

Because this pattern is a normal heat call, there is nothing to reset when heat is coming. A reset only enters the picture when the lights show a normal call but the furnace will not heat, and even then, do it once and only if your owner manual allows it. A reset means turning the furnace service switch off, waiting about a minute, and turning it back on. If the furnace fails again, stop. Repeated resets can mask a real safety problem, and each restart sends gas toward a burner that may not be lighting cleanly.

What a homeowner may safely do:

  • Confirm the furnace service switch, which usually looks like an ordinary light switch on or near the furnace, is on, and that the breaker has not tripped.
  • Confirm the thermostat is in heat mode, has fresh batteries if it uses them, and is set above room temperature.
  • Confirm the manual gas valve handle on the furnace supply pipe is in line with the pipe. Do not turn any valve you do not recognise.
  • Replace a dirty filter and make sure the blower door is fully closed. Many furnaces will not run with that door off; it is a safety interlock, not a fault.
  • From outside, clear snow, leaves, nests or plant growth from the intake and exhaust terminals without moving the pipes.
  • Look at the visible condensate hose and pump for kinks, overflow or water on the floor.
  • Do one reset, and only if the owner manual allows it.

When a Lennox heat-call problem becomes a licensed call, and the gas safety line

What a homeowner should not do: remove burner or control panels, touch the gas valve or its wiring, bypass or jumper a safety switch, jumper thermostat terminals at the board, sand or pull a flame sensor, or keep cycling power. Gas work in BC is restricted to licensed gas fitters under Technical Safety BC, and most electrical work inside a furnace is restricted to licensed trades as well. Once the owner checks above are done and heat still does not arrive, it is a licensed call.

The safety line is simple. If you smell gas, or your carbon monoxide alarm sounds, leave the house with everyone, including pets, without switching lights or appliances on or off and without using the thermostat. Call FortisBC or 911 from outside. Do not go back in until you are told it is safe. Carbon monoxide has no smell, so the alarm is your only warning; every home with a gas furnace should have working CO alarms near sleeping areas, tested regularly and replaced at the age the alarm maker specifies.

Other signs that mean stop and call rather than troubleshoot: a burning or scorching smell when the burners light, soot or discolouration around the furnace or vent pipe, water dripping from the vent pipe into the cabinet, a loud bang at ignition, or the furnace shutting off and restarting repeatedly while the lights keep showing a normal heat call. Call (604) 473-9690 and describe what you are seeing.

How our Lennox furnace repair visit works, step by step

When you call (604) 473-9690 about a Lennox furnace, this is what the visit looks like from first call to finished job. We book same-day where we can, and in a cold snap we tell you honestly when the earliest slot is rather than promising an arrival window we cannot keep.

  • Step 1, the call: we ask what the lights are doing, what the furnace is doing, roughly how old it is, and whether anyone smells gas or has a CO alarm sounding. A gas smell goes to FortisBC or 911 first.
  • Step 2, arrival and safety check: the technician checks for gas at the appliance and confirms the CO situation before running the furnace.
  • Step 3, reading the board: we read the light pattern, check the stored fault history where the board keeps one, and run a heat call while watching each stage of the sequence.
  • Step 4, testing with the right meters: a multimeter for voltage and continuity, a microamp test for flame sensing, a manometer for gas pressure and venting pressure, and a combustion analyser where combustion is in question. We test rather than guess.
  • Step 5, proving the cause: the parts most often involved behind a normal heat call with no heat are the flame sensor, igniter, condensate trap and hoses, the venting safety switch and its tubing, the filter and blower, and less often the gas valve or control board. Which one it is gets proven on the meter, not assumed.
  • Step 6, written quote: before any work beyond the diagnosis, you get a written quote describing the repair, the part and the labour. Nothing is replaced without your approval.
  • Step 7, repair and safety testing: after the repair we test the safeties, confirm clean ignition and a stable flame, check temperature rise across the furnace, check venting and condensate drainage, and run a full heat cycle back to a normal heat call.
  • Step 8, paperwork: you get a written record of what we found, what we did, and anything worth watching. Where the work needs a permit, such as gas piping changes or a furnace replacement, we take out the permit and arrange the inspection.

Repair or replace an older Lennox furnace, and Lennox furnace service near me in Greater Vancouver

A normal heat call pattern says nothing about the age of the furnace, but a no-heat visit often raises the question. Our view as installers is that most single repairs on a sound furnace are worth doing; a furnace that only needed a flame sensor cleaned or a condensate trap cleared does not need replacing. Replacement starts to make sense when several things line up: a heat exchanger with cracks or signs of combustion leakage, which is a safety finding that usually ends the conversation; the same no-heat fault returning after proper repairs; a major part such as the control board, inducer or blower motor failing on a furnace well into the second half of its service life, since these are among the more expensive parts on a gas furnace; parts that are getting hard to source; or rooms that never heat evenly.

If you do replace, the most flexible path for most Metro Vancouver homes is dual fuel: a heat pump that handles heating and cooling for most of the year, paired with a gas furnace kept as backup for cold snaps. The two share the ductwork and one thermostat. We size replacements with a load calculation rather than copying the old nameplate, and we put the scope, equipment, venting, gas piping, permit and inspection in a written quote so you can compare like with like.

We work across Metro Vancouver from our Burnaby base. Our mild, wet coastal climate means furnaces here run long, gentle cycles for much of the year, which is easy on burners but hard on condensate drains and on outdoor terminals exposed to rain, moss and leaf fall. When a cold snap arrives, those small weaknesses show up all at once. Housing stock varies within every city, so we describe what we commonly run into in general terms:

  • Vancouver: older detached houses with upgraded forced-air heating alongside newer townhomes and laneway homes where furnaces sit in tight closets and vent routing is limited.
  • Burnaby: older detached houses, townhome complexes and strata buildings where vent terminals and condensate routes may need strata approval.
  • Surrey: many newer subdivisions with high-efficiency furnaces, plus older homes where original ductwork was not designed for current equipment.
  • Richmond: flat, low-lying neighbourhoods where crawlspace ductwork and condensate drainage get extra attention.
  • Coquitlam and the Tri-Cities, including Port Coquitlam and Port Moody: hillside homes where snow and leaves can drift against side-wall vent terminals.
  • The North Shore, North Vancouver and West Vancouver: wetter, colder pockets at elevation where terminal blockage and heavier heating loads come up more often.
  • New Westminster: older houses with retrofitted forced-air systems and tight mechanical spaces.
  • Delta and Langley: a mix of older detached homes and newer builds, with renovations where we check venting clearances carefully and longer gas piping and duct runs on larger lots.
  • Brands we service include Lennox, Carrier, Bryant, Trane, American Standard, Rheem, Goodman, Amana, York and Daikin. We service these brands as an independent contractor; we are not an authorised dealer or warranty centre for any of them.
  • Why owners call us: BC Wide Home Services Ltd is an independent Technical Safety BC licensed contractor, gas contractor licence LGA0090068 and Class B gas licence CGA0028029, serving Metro Vancouver since 1999. Work is done by licensed gas fitters, permits and inspections are handled where required, and you get a written quote before any work beyond diagnosis.

More questions homeowners ask

What does DS1 and DS2 simultaneous fast flash mean on a Lennox furnace?

It means a normal heat call: the thermostat has asked for heat and the control board is starting the heating sequence. It is a status signal, not a fault. Confirm against the manual for your unit, since boards differ across model generations. If warm air follows within a few minutes, nothing needs fixing.

Can I reset my Lennox furnace when DS1 and DS2 are fast flashing?

If heat is coming, there is nothing to reset. If the lights show a heat call but no heat arrives, you can turn the furnace switch off and back on once, but only if your owner manual allows it. If it fails again, stop and call a licensed technician, because repeated resets can hide a safety problem.

Is it safe to run my Lennox furnace while both lights flash fast?

Normally yes, because the pattern simply shows the furnace answering a heat call. It stops being safe the moment you smell gas, notice scorching or your CO alarm sounds. In that case leave the house with everyone and call FortisBC or 911 from outside.

Why is my Lennox furnace flashing DS1 and DS2 but not heating?

The heat call is being received, but something later in the sequence is not completing or the warm air is not reaching the rooms. The usual suspects are a dirty filter, blocked outdoor vent terminals, a backed-up condensate drain, a closed gas valve, or an ignition and flame sensing problem. Do the owner-safe checks, then call (604) 473-9690 for a licensed diagnosis.

Do you offer same-day Lennox furnace repair near me in Greater Vancouver?

We book same-day where we can, and we tell you honestly when we cannot. During cold snaps demand jumps across Metro Vancouver, so we give you the real earliest time rather than a promised arrival window. Call (604) 473-9690 and describe what the furnace lights are doing.

Is BC Wide a Lennox dealer or warranty centre?

No. BC Wide Home Services Ltd is an independent TSBC-licensed contractor that services Lennox and other major furnace brands. We are not an authorised dealer or warranty centre, and you receive a written quote before any repair beyond diagnosis.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote