★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Lennox Furnace Code DS1 fast flash, DS2 slow flash — Main power polarity reversed | BC Wide

Error Codes, Furnace, Hvac

Lennox Furnace Code DS1 fast flash, DS2 slow flash — Main power polarity reversed | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Lennox Furnace Code DS1 fast flash, DS2 slow flash — Main power polarity reversed | BC Wide

Lennox Furnace Code DS1 fast flash, DS2 slow flash — Main power polarity reversed | BC Wide

Quick answer

On a Lennox furnace, DS1 fast flash with DS2 slow flash indicates main power polarity reversed: line and neutral are swapped at the furnace’s main power connection, and the control will not run the furnace until polarity is correct (confirm against the manual for your unit). In most cases you will have no heat. It is a wiring fault, not a worn-out part, and the fix belongs to a licensed technician or electrician. Confirm the switch is on, leave every panel closed, and call (604) 473-9690.

If your Lennox furnace is showing DS1 fast flash, DS2 slow flash (Main power polarity reversed), here’s exactly what it means and what to do. This guide is part of our full Lennox furnace error code list.

Severity: Needs attention.

What DS1 fast flash, DS2 slow flash means on a Lennox furnace

Line and neutral are reversed at the furnace’s main power connection. The control requires correct polarity to operate.

Common causes

  • Line and neutral wires swapped at the furnace, disconnect, or an outlet/junction box

What you can safely check first

  1. Confirm the furnace and its disconnect switch are on
  2. Do not open the wiring compartment — a technician or electrician must correct the line/neutral polarity

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Lennox furnace usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver furnaces since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Lennox furnace repair across Greater Vancouver

If a Lennox furnace showing DS1 fast flash, DS2 slow flash won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast furnace repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Lennox furnace codes

Frequently asked questions

Is DS1 fast flash, DS2 slow flash on a Lennox furnace serious?

It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs Lennox furnaces 7 days a week across Greater Vancouver.

How do I reset a Lennox furnace after DS1 fast flash, DS2 slow flash?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Lennox Furnace Error Code DS1 Fast Flash DS2 Slow Flash: what it means for your home

In plain terms, this code says the electricity reaching your furnace is connected backwards. Household power arrives on two current-carrying conductors: the line, or hot, wire that carries voltage, and the neutral, which should sit close to ground potential. When a Lennox furnace flashes DS1 fast and DS2 slow, the control has detected that those two conductors are reversed at the main power connection, and the control requires correct polarity to operate. Confirm that meaning against the manual for your unit, because diagnostic tables can differ between control generations.

Why does a furnace care which wire is which? Most modern gas furnace controls prove the burner flame with a tiny electrical signal passed through the flame itself, a method commonly called flame rectification. That signal is referenced to neutral and ground. With line and neutral swapped, the control may not be able to read the flame signal reliably, and the switches and fuses in the circuit can end up interrupting the neutral instead of the hot wire. A control designed to check polarity simply stops the sequence rather than gamble on either problem.

What it means day to day: in most cases there will be no heat until the wiring is corrected. If your hot water comes from a separate gas tank or tankless water heater, that appliance has its own supply and is not affected by this furnace fault. If a heat pump is paired with this furnace as a dual-fuel system, the heat pump may still run in mild weather depending on how the controls are configured, but the gas backup you rely on during a cold snap will not be available until the furnace is fixed.

There is also a safety angle that has nothing to do with comfort. When polarity is reversed, switching off the furnace service switch may break the neutral and leave parts of the appliance energized. That is one more reason the wiring compartment stays closed for anyone who is not licensed to work in it.

How owners usually describe this problem when they call us:

  • The furnace will not start a heating cycle at all, even though the thermostat says it is calling for heat.
  • The vents are silent or the house is slowly getting colder while the thermostat display looks normal.
  • Two lights on the furnace control are flashing at different speeds, visible through the small window in the blower door.
  • The problem showed up right after electrical work: a panel upgrade, a new service switch, a basement suite renovation, or a new thermostat or accessory install.
  • The furnace was recently replaced, moved or reconnected and the code appeared on the very first start.
  • Someone already switched the power off and on, and the same light pattern came straight back.

Lennox furnace DS1 fast flash DS2 slow flash causes, most common first, and what you can safely check

On site, a reversed-polarity reading almost always traces back to a wiring decision somewhere between the electrical panel and the furnace control. The table below lists the causes we look at, ranked roughly by how often they turn up on Metro Vancouver jobs, along with what you can safely look at yourself and where it becomes a licensed call.

Owner-safe checks, in order. These rule out a second problem and give the technician useful information; none of them will correct reversed wiring:

  • Confirm the furnace service switch, usually a light-style switch on or near the furnace, and its breaker in the panel are both on. Do not reset a breaker that trips again.
  • Confirm the gas supply valve to the furnace is open, with the handle running parallel to the pipe. A closed valve does not cause this code, but it saves a second visit once the wiring is fixed.
  • Confirm the thermostat is set to heat and set above room temperature, with fresh batteries if it uses them.
  • If your owner manual allows a power reset, do it once only: switch off, wait a minute, switch back on. If the same pattern returns, stop there.
  • From the ground and only if it is safe, check that the outside intake and exhaust terminals are clear of snow, leaves or nests. Not the cause of this code, but good to know they are clear.
  • Look at the visible condensate drain line for kinks or a disconnected hose, without opening any panel.
  • Do not open the blower door, burner compartment, junction box or control area, and never bypass, jumper or swap wires yourself.
Likely cause, most common firstWhat happenedOwner-safe checkWhen it becomes a licensed call
Line and neutral swapped at the furnace connectionThe supply conductors were landed on the wrong terminals when the furnace was installed, replaced or reconnected.Note whether the code appeared right after installation or service. Do not open the junction box.Always. Correcting terminations at the furnace is licensed technician work.
Swapped at the service switch or disconnectA replaced or added switch near the furnace was wired with the conductors reversed.Confirm the switch is on and note whether it was recently changed.Always. The switch box is live wiring.
Miswired receptacle or junction box upstreamSome furnaces are fed through a receptacle or a splice box; a reversed receptacle or splice carries the error to the furnace.Tell us about any recent electrical work in the basement, garage or utility room.Always. This may be building wiring that needs a licensed electrical contractor and, in many cases, a permit.
Renovation or panel work changed the circuitA panel upgrade, circuit relocation or suite build re-routed the furnace circuit.Find out who did the work and whether it was permitted and inspected.Always. The original installer or a licensed electrician should verify the circuit.
Ground or neutral problem affecting the readingA loose, corroded or missing ground or neutral can make voltages read abnormally, which a technician rules out while confirming the fault.Report flickering lights or other odd electrical behaviour in the house. Touch nothing.Always. A loose neutral can be a shock and fire hazard.
Control sensing fault, less commonOccasionally the wiring proves correct and the control’s sensing circuit is the issue.None. This is only identified after the wiring has been proven correct with a meter.Always. Control diagnosis and replacement is technician work.

How our Lennox furnace repair visit works for a reversed-polarity code

If you ever smell gas or a carbon monoxide alarm sounds, stop everything. Do not operate switches, get everyone out of the home, and call FortisBC or 911 from outside. Only go back in when you have been told it is safe. For the polarity code itself, here is what a correct repair visit looks like, in the order we do it. It is a fair standard to hold any contractor to.

  • Step one, the phone call: we ask what the lights are doing, when it started, and whether any electrical or renovation work happened recently. That history often points straight at the cause. We book same-day where we can; during a cold snap the schedule fills quickly, and we will tell you honestly what the earliest realistic visit is rather than promise an arrival window.
  • Step two, safety on arrival: we check the mechanical room for gas odour, confirm the venting is intact, and record the light pattern before touching power.
  • Step three, measure rather than guess: with a properly rated meter we test line to neutral, line to ground and neutral to ground at the furnace connection, then work upstream through the service switch, any receptacle or junction box, and toward the panel. The readings show exactly where the swap happened.
  • Step four, decide who fixes it: if the reversal is at the furnace terminals or within the appliance wiring our technicians are licensed to service, we correct it on the spot. If it is in building wiring upstream of the appliance, that is regulated electrical work in BC, and we say so plainly so a licensed electrical contractor can correct it, with a permit where one is required.
  • Step five, check the parts most often involved: once polarity is right, we watch a full start sequence and confirm the control, flame sensing, igniter, inducer and pressure switch, and door switch all behave normally. A wiring fault can hide a second problem, and we would rather find it while we are there.
  • Step six, test the safeties: we run complete heating cycles, verify the high-limit, rollout and pressure safeties respond as designed, check the burner flame and venting, and measure carbon monoxide in the flue gases and the room.
  • Step seven, a written quote before any work beyond diagnosis: if anything needs a part or more labour, you see a written quote first, and nothing proceeds until you approve it.
  • Step eight, paperwork you keep: a written summary of what was measured, where the reversal was found, what was corrected, and any recommendations.

Repair or replace an older Lennox furnace after a polarity code?

On its own, reversed polarity is almost never a reason to replace a furnace. It is a wiring error, and once corrected the furnace usually runs exactly as it did before. Cost is often the good news with this code: a wiring correction at the appliance tends to be one of the smaller repairs we perform, because no major component has failed. The bill grows only if upstream electrical work is needed or the control was damaged, and in either case you get a written quote before anything is done. We do not treat a wiring fault as a sales opening, and you should be wary of anyone who does.

The repair-or-replace question only becomes real when the visit uncovers something else on an older unit. These are the findings that legitimately shift the decision:

  • A cracked or badly corroded heat exchanger confirmed by inspection, which is a safety issue rather than a comfort one.
  • A failed control on a furnace old enough that compatible replacement parts are hard to source.
  • A run of repairs over the last few seasons with more clearly on the way.
  • Venting that no longer suits the appliance under current code, which can turn a simple part swap into a larger job.
  • A home that has changed: an addition, a new suite, or a plan for a heat pump that calls for different capacity or ductwork.
  • When replacement does make sense, our default recommendation for most Metro Vancouver homes is dual fuel: a heat pump for the long mild shoulder seasons, paired with a modern gas furnace that carries the house through cold snaps. You keep a gas backup you can trust on the coldest nights, and you get a written comparison of repair and replacement options with no pressure at the door.
  • If your furnace is still under the manufacturer’s warranty, remember that we are an independent contractor, not a warranty centre. We document what we measured in writing so you can take it to the warranty provider if a covered part turns out to be involved.

Lennox furnace service near you in Vancouver, Burnaby, Surrey and across Greater Vancouver

We diagnose and repair this code across Greater Vancouver: Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. Housing stock shapes how a polarity fault happens, so here is what we commonly see, in general terms rather than promises about any particular street or home:

Brands we service: alongside Lennox, our technicians work on gas furnaces from Carrier, Bryant, Trane, American Standard, Goodman, Amana, Rheem, Ruud, York, Daikin and Napoleon. We are independent, so we have no stake in which brand is in your basement; we just want it wired and running correctly.

Climate matters as well. Metro Vancouver winters are mild and damp rather than bitterly cold, so furnaces run long, gentle cycles for months. A no-heat fault during a wet cold spell is usually a comfort and moisture problem rather than an immediate danger for most households, but if you have seniors, infants or anyone medically vulnerable in the home, call early and tell us so we can prioritise where possible.

  • Vancouver and Burnaby: many older detached houses have been renovated more than once, and furnace circuits are sometimes re-routed during basement suite work. Older wiring mixed with newer wiring is exactly where swapped conductors tend to hide.
  • New Westminster: plenty of older and character homes where electrical changes may have been made over several decades, so we trace the circuit rather than assume anything.
  • Surrey, Langley and Delta: a mix of established homes and newer subdivisions. On newer houses the fault often traces back to a replaced furnace or a switch changed after the original installation.
  • Richmond: furnaces are often tucked into tight utility closets, which makes careful access and clear, well-labelled wiring paths matter.
  • Coquitlam and the Tri-Cities: hillside homes and finished basements where the furnace feed has frequently been modified during renovations.
  • The North Shore: older homes on sloped lots, sometimes with long circuit runs from the panel, and wet weather that makes us double-check outdoor terminals and nearby connections are dry and sound.

Who should fix a Lennox furnace polarity fault: licensing, permits and what to get in writing

Reversed polarity sits right where gas work and electrical work meet, so who touches it matters. BC Wide Home Services Ltd is an independent contractor licensed by Technical Safety BC, gas contractor licence LGA0090068, with Class B gas licence CGA0028029, serving Metro Vancouver since 1999. Our own licensed gas fitters do the diagnosis and the appliance work; we are not an authorised dealer or a warranty centre, and we do not hand your job to subcontractors.

In BC, gas appliance work must be done by a licensed gas fitter working under a licensed contractor, and permits apply to installations and many alterations. Building wiring is regulated electrical work. A correct job respects both: we fix what our licences cover and tell you plainly when a licensed electrical contractor is needed. Before you hire anyone for this code, make sure you will see the following in writing:

  • The contractor’s legal name and Technical Safety BC licence numbers.
  • A written diagnosis naming where the reversal was found, measured with a meter rather than guessed.
  • A written quote before any work beyond diagnosis.
  • A note on whether a permit is required, who is pulling it, and whether an inspection follows.
  • Confirmation that the safeties were tested and carbon monoxide was checked after the repair.
  • Honest timing: same-day where we can, with no guaranteed arrival window. Call (604) 473-9690 and mention DS1 fast flash with DS2 slow flash so we arrive prepared.

More questions homeowners ask

What does DS1 fast flash DS2 slow flash mean on a Lennox furnace?

It indicates main power polarity reversed: line and neutral are swapped at the furnace’s main power connection, and the control will not operate until polarity is correct. Confirm that meaning against the manual for your unit, since control generations differ. The fix is a wiring correction by a licensed technician, and sometimes a licensed electrician if the swap is in the building wiring.

Can I reset a Lennox furnace showing DS1 fast flash DS2 slow flash?

Only if your owner manual allows it, and only once: turn the service switch off, wait a minute, and turn it back on. Because the cause is wiring rather than a passing glitch, the same pattern usually returns, and repeated resetting will not fix it. Leave the panels closed and call a licensed technician.

Is it safe to run a Lennox furnace with reversed polarity?

No. The control is designed to refuse to run, and nobody should try to work around it. Reversed polarity can mean the service switch breaks the neutral instead of the hot wire, leaving parts energized, and it can interfere with flame sensing. Leave it off until the wiring is corrected.

Can I fix reversed polarity on my Lennox furnace myself?

No. Swapping conductors in the furnace junction box, the service switch or an upstream box is live electrical work, and in BC it belongs to licensed trades. Your part is the owner-safe checks: switch and breaker on, gas valve open, thermostat calling, and one reset if the manual allows it.

Why did my Lennox furnace show this code right after electrical work?

Because recent wiring changes are the most common way it happens. A new switch, receptacle, panel change or suite renovation can land line and neutral on the wrong terminals. Tell the technician about the timing, since it usually makes the diagnosis quick.

Is there Lennox furnace repair near me in Greater Vancouver for this code?

Yes. BC Wide covers Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We book same-day where we can but never promise a guaranteed arrival time. Call (604) 473-9690.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote