★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Lennox Furnace Code DS1 slow flash, DS2 OFF — Flame sensed without gas valve energized | BC Wide

Error Codes, Furnace, Hvac

Lennox Furnace Code DS1 slow flash, DS2 OFF — Flame sensed without gas valve energized | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Lennox Furnace Code DS1 slow flash, DS2 OFF — Flame sensed without gas valve energized | BC Wide

Lennox Furnace Code DS1 slow flash, DS2 OFF — Flame sensed without gas valve energized | BC Wide

Quick answer

Lennox furnace error code DS1 slow flash, DS2 OFF means the control is sensing a flame signal while the gas valve is not energized: flame present out of sequence (confirm against the manual for your unit). Treat it as a safety fault. Set the thermostat to OFF and do not keep resetting. If you smell gas or a CO alarm sounds, leave and call FortisBC or 911 from outside. A licensed gas technician needs to test the gas valve, flame sensor circuit, wiring and control board. Call BC Wide at (604) 473-9690.

If your Lennox furnace is showing DS1 slow flash, DS2 OFF (Flame sensed without gas valve energized), here’s exactly what it means and what to do. This guide is part of our full Lennox furnace error code list.

Severity: Critical — likely no heat / lockout.

What DS1 slow flash, DS2 OFF means on a Lennox furnace

The control detects a flame signal when the gas valve is not energized (flame present out of sequence). The system treats this as a safety fault.

Common causes

  • Gas valve leaking through / not fully closing
  • Flame sensor or control board fault
  • Wiring issue

What you can safely check first

  1. Set the thermostat to OFF and do not attempt to operate the furnace
  2. If you smell gas, leave the home and call your gas utility / a professional
  3. Schedule a technician — this is an internal safety fault

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Lennox furnace usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver furnaces since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Lennox furnace repair across Greater Vancouver

If a Lennox furnace showing DS1 slow flash, DS2 OFF won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast furnace repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Lennox furnace codes

Frequently asked questions

Is DS1 slow flash, DS2 OFF on a Lennox furnace serious?

It’s a lockout/safety code — the furnace has shut down and needs prompt diagnosis. BC Wide repairs Lennox furnaces 7 days a week across Greater Vancouver.

How do I reset a Lennox furnace after DS1 slow flash, DS2 OFF?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Lennox furnace error code DS1 slow flash, DS2 OFF: what it means for you

In plain terms, your furnace’s control board is seeing evidence of a flame at a moment when it has not told the gas valve to open. A gas furnace is supposed to follow a strict order every cycle: the thermostat calls for heat, the inducer fan purges the heat exchanger, the igniter heats up, the control energizes the gas valve, and only then should a flame appear and be proven by the flame sensor. When the control picks up a flame signal outside that order, it can no longer trust that the gas is under its control, so it treats the situation as a safety fault rather than a comfort or performance problem. Confirm the exact wording against the manual or the wiring label inside your unit’s door, because Lennox control generations differ.

For your household this usually means three things. Heat: expect the furnace to lock out or behave abnormally until it has been diagnosed, so plan for a cooler house if the weather has turned. Hot water: a separate gas water heater runs on its own controls and is not affected by this furnace code, but any gas smell anywhere in the home changes the plan immediately. Safety: a flame signal out of sequence can be a real flame from gas that should not be flowing, which is exactly why this is not a code to clear and forget.

Homeowners rarely describe this fault by the light pattern. These are the things people actually tell us when they call about it:

  • The furnace blower keeps running and will not shut off, even with the thermostat turned down or switched to off.
  • The burners stay lit, or a small flame is visible through the viewing window, after the house has already warmed up.
  • The furnace short-cycles, runs at odd times, or will not start a normal heating cycle at all.
  • The status lights visible through the small window in the lower door show one light flashing slowly and the other light off.
  • The house is cold and the furnace appears to be locked out.
  • A faint gas smell near the furnace, or a carbon monoxide alarm sounding, alongside any of the above. This one is a leave-the-house symptom, not a troubleshooting symptom.

Lennox furnace error code DS1 slow flash, DS2 OFF: what we check first

These are the likely causes, roughly in the order we tend to find them on site, although every furnace and every installation is different. For each one there is a short note on what a homeowner can safely look at and where it becomes a licensed gas call. None of the owner checks involve removing panels, touching wiring, jumpering anything or working on the gas train.

Cause 1, gas valve leaking through or not fully closing. The gas valve is supposed to stop gas completely the instant the control de-energizes it. If it sticks partly open or its seat no longer seals, a small flame can keep burning after the heating call ends, and the control correctly reports flame without a valve signal. Owner check: with the thermostat set to OFF, look through the viewing window. If you see flame and you do not smell gas, close the manual gas shutoff on the pipe beside the furnace only if you can identify it with certainty (a lever handle turned crosswise to the pipe is closed), then call. If you smell gas, touch nothing and leave. A valve that leaks through is always a licensed repair, and it is replaced, never adjusted, tapped or cleaned.

Cause 2, control board fault. The board reads the flame signal and decides whether it is real. A failing board can report a flame that does not exist, or a relay on the board can stick and keep the valve circuit live when it should be off. Owner check: note what the lights do, whether flame is visible, and whether the blower runs on after the thermostat is satisfied. That information saves diagnostic time. Testing the board, its relays and its outputs is licensed work.

Cause 3, flame sensor circuit. The flame sensor is a metal rod that sits in the burner flame; the board proves flame by measuring a very small electrical current passing through it. A cracked insulator, a damaged sensor or a chafed sensor lead can upset that reading. Owner check: nothing beyond reporting the symptom. Do not pull and clean the sensor on a furnace showing this code, because the real question is whether gas is flowing when it should not be.

Cause 4, wiring issue. A chafed wire, a loose or corroded connector, moisture at a terminal, or rodent damage to the harness can feed the board a false signal or keep a circuit energized. Owner check: confirm the furnace power switch is on and the breaker has not tripped, and mention any recent renovation, new appliance or water leak near the furnace. Inspecting and repairing wiring inside the cabinet belongs to a licensed technician.

The table below lists every check a homeowner can safely make while waiting for a technician, and the point at which each one stops being yours to handle.

  • Safety line: if you smell gas (a rotten-egg odour) or a carbon monoxide alarm sounds, do not reset the furnace and do not operate light switches or appliances. Get everyone, including pets, out of the home and call FortisBC or 911 from outside. Call us once you are safe.
  • Every home with gas appliances should have working CO alarms near the sleeping areas and on each level. If yours are missing or past their replacement date, fix that before the furnace is back in service.
Owner-safe checkWhat you are looking forWhen it becomes a licensed call
Thermostat set to OFFWhether the burners and blower stop once the call for heat endsFlame still visible, or the blower runs on with no call for heat
Furnace power switch and breakerSwitch on, breaker not trippedThe breaker trips again, or the switch area is warm, scorched or smells of burning
Manual gas shutoff beside the furnaceA handle you can identify with certaintyYou are unsure which valve it is, or you smell gas at any point
One reset, only if your owner manual allows itWhether the code comes straight backAfter that single reset; never cycle power over and over
Outdoor intake and exhaust terminalsSnow, leaves, needles, nests or debris at the pipe openingsClearing them changes nothing, or a pipe is cracked, sagging or disconnected
Visible condensate drain and tubingLeaks, puddles, a kinked or disconnected hoseAny sign that water has reached the cabinet or the controls
Carbon monoxide alarmsAlarms working and silentAny alarm at all: leave the home and call from outside

How our Lennox furnace repair visit works, step by step

A correct repair for this code is not a part swap. The technician has to prove why the board saw a flame it did not ask for, because replacing the wrong part leaves a gas safety problem in place. This is how a visit from one of our licensed gas fitters runs from first call to sign-off.

  • Step 1, the phone call. We ask what the lights are doing, whether flame is visible with the thermostat off, whether anyone smells gas and whether the CO alarms are quiet. If there is any sign of gas or carbon monoxide, we tell you to leave and call FortisBC or 911 before anything else. We book the visit same-day where we can; during a cold snap the schedule fills quickly, and we will tell you honestly when we can arrive rather than promise a window we cannot keep.
  • Step 2, safety checks on arrival. The technician checks for gas at the appliance and along the nearby piping with a combustible gas detector, takes an ambient carbon monoxide reading, and confirms the furnace is safe to work on before opening anything.
  • Step 3, reading the fault history. Lennox controls commonly store recent faults. We read the current status and the stored history to learn whether this code is new, intermittent or long-running, and whether other recorded faults point in the same direction.
  • Step 4, proving the flame circuit. With a meter that reads the very small flame-sensing current, we measure the signal during a normal cycle and, more importantly, after the call ends. Comparing that reading with the voltage at the gas valve tells us whether we are chasing a real flame or a false signal.
  • Step 5, testing the gas valve. We confirm the valve has no voltage when it should be closed and watch the burners. If flame persists with the valve de-energized, the valve is leaking through and must be replaced. We also measure inlet and manifold gas pressure with a manometer, because pressure problems can mask or mimic other faults.
  • Step 6, board, sensor and wiring. We test the board’s relays and outputs, inspect the flame sensor and its insulator, and trace the harness and connectors for moisture, heat damage, corrosion or chewed insulation.
  • Step 7, a written quote before any work beyond diagnosis. You receive a written description of what we found, the readings that support it, what we recommend and the price. The parts most often involved with this code are the gas valve, the control board, the flame sensor and its lead, and wiring or connectors. A gas valve or a control board is one of the more expensive parts on a gas furnace, so you should see the evidence before you approve it. Nothing is replaced without your sign-off.
  • Step 8, repair and full safety test. After the repair we run several complete heating cycles and confirm the flame signal drops away the moment the valve closes. We test the limit, pressure and rollout safeties, check combustion and venting, and leave the furnace running normally. Where Technical Safety BC requires a permit for the work, we file it, and the paperwork you keep lists what was done.

Should you repair or replace an older Lennox furnace after this fault?

On a furnace that is reasonably young and otherwise healthy, this code is usually a repair decision, not a replacement decision. A new gas valve or control board, installed and tested properly, returns the furnace to safe operation. The question gets harder on an older furnace, and the honest answer depends on what the technician finds once the cabinet is open, not on the code alone.

These are the factors we put in writing when a homeowner asks us whether an older Lennox furnace is worth fixing:

  • Age and service history. A furnace well into its later years that has needed several significant repairs recently is a different proposition from one that has run quietly for most of its life.
  • Heat exchanger and venting condition. If the inspection turns up cracking, heavy corrosion or venting problems, that weighs far more than the cost of the valve or board.
  • Parts availability. Some older controls and valves are discontinued, and the available replacement may be a universal part. That can be perfectly safe when installed correctly, but it is worth knowing before you approve the work.
  • Comfort and efficiency. An older non-condensing furnace works harder for the same heat than a modern condensing furnace. We explain what an efficiency rating means rather than promise a number for your home.
  • Warranty paperwork. If the furnace is newer, look for the registration and installation records before approving parts. We are an independent contractor, not a Lennox warranty centre, but we will tell you which documents matter.
  • Your plans for the house. A planned renovation, suite addition or sale changes the right answer.

Lennox furnace service near me: Greater Vancouver coverage and the brands we service

We are based in Burnaby and have worked on furnaces across Metro Vancouver since 1999. Our mild, wet coastal climate means furnaces here run long, low-intensity seasons through the damp autumn and spring, then get pushed hard during the occasional cold snap or snowfall. Those cold snaps are when lockout calls like this one arrive all at once, which is why we say same-day where we can and nothing more.

In Vancouver and Burnaby we see a wide range of housing, from older detached homes where the furnace sits in a tight basement mechanical room to newer townhouses and strata homes with furnaces in closets or garages. Access and venting routes in older homes are often the things that shape the job. New Westminster has a share of older character homes where gas piping and wiring have been modified over the years, so we look closely at what feeds the furnace, not just the furnace itself.

Richmond and Delta sit low and close to the river and ocean, and many homes there have no full basement, so furnaces are commonly found in garages, utility rooms or closets, with their own clearance and venting considerations. In Surrey and Langley, newer subdivisions mostly run condensing furnaces with plastic venting through a side wall, where intake and exhaust terminals can sit close to fences, decks or garden beds that collect leaves and snow. Coquitlam and the Tri-Cities, including Port Coquitlam and Port Moody, mix hillside detached homes with dense townhouse and strata complexes, where strata rules can affect where vent terminals may go. On the North Shore, including North Vancouver and West Vancouver, the heavy rain and tall trees mean terminals collect needles, leaves and the occasional nest, and damp conditions reward a close look at connectors and condensate drains.

We service Lennox furnaces and other common gas furnace brands found in Metro Vancouver homes. We work on these brands as an independent TSBC-licensed contractor, not as a dealer or factory-authorized service centre for any of them:

  • Lennox
  • Carrier and Bryant
  • Trane and American Standard
  • Goodman and Amana
  • Rheem
  • York
  • Daikin
  • Napoleon
  • KeepRite

Why trust a TSBC-licensed independent gas contractor with this Lennox code?

This code sits squarely in licensed gas work. In British Columbia, diagnosing and repairing gas valves, burners, controls and the wiring that runs them is restricted to licensed gas fitters working for a licensed contractor, and that is the only way we work. BC Wide Home Services Ltd holds Technical Safety BC gas contractor licence LGA0090068, and our Class B gas licence is CGA0028029. The technician who opens your furnace is a licensed gas fitter on our own team.

Being independent matters for a fault like this. We are not tied to any equipment brand, so our recommendation follows what the meters show: a repair when a repair is right, and an honest replacement conversation when the furnace has reached that point. When a replacement makes sense, we lead with a high-efficiency gas furnace, and for homeowners who want to add cooling or reduce gas use, a dual-fuel system, in which a heat pump handles the mild months and the gas furnace stays as backup for cold snaps.

Whatever the outcome, this is what you should see in writing from us, and from any contractor you hire for this code:

  • What was found, including the flame signal and gas valve readings that support the diagnosis.
  • The parts recommended, described in plain language, with the written quote approved before any work beyond diagnosis.
  • The safety tests performed after the repair, including confirmation that flame stops when the valve closes.
  • A permit reference where Technical Safety BC requires one for the work.
  • The contractor’s licence number and the name of the technician who did the work.

More questions homeowners ask

What does DS1 slow flash, DS2 OFF mean on a Lennox furnace?

It means the control is detecting a flame signal while the gas valve is not energized, which is flame present out of sequence. The control treats this as a safety fault because it cannot confirm that the gas is under its control. Confirm the meaning against the manual for your unit, and have a licensed gas technician diagnose it.

Can I reset a Lennox furnace showing DS1 slow flash, DS2 OFF?

Only once, only if your owner manual allows it, and only if you cannot see flame with the thermostat off and you do not smell gas. If the code returns, stop and call a licensed technician. Repeated resets can hide a gas valve that is leaking through, which is the most important cause to rule out.

Is it safe to run my Lennox furnace with this code?

No. Set the thermostat to OFF and leave the furnace off until a licensed gas fitter has tested it, because the fault can mean gas is reaching the burners when it should not. If you smell gas or a carbon monoxide alarm sounds, leave the home and call FortisBC or 911 from outside.

Why does my Lennox furnace blower keep running when the thermostat is off?

On many furnace controls, when a flame is sensed out of sequence the board keeps the blower and inducer running to carry heat and combustion products out of the appliance. That is the control protecting you, not the fault itself. Leave it alone and book a licensed technician to find out why the flame signal is there.

Can a dirty flame sensor cause Lennox code DS1 slow flash, DS2 OFF?

It is unlikely to be the whole story. A dirty sensor normally weakens the flame signal, while this code is about a flame signal appearing when it should not. Cleaning the sensor will not fix a gas valve that leaks through or a faulty board, so this code needs a proper licensed diagnosis rather than a quick clean.

Who fixes Lennox furnace error code DS1 slow flash, DS2 OFF near me in Greater Vancouver?

BC Wide Home Services Ltd diagnoses and repairs this code across Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We are an independent TSBC-licensed gas contractor and book same-day where we can, with a written quote before any work beyond diagnosis. Call (604) 473-9690.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote