★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Lennox Furnace Code E207 — Hot surface igniter open | BC Wide

Error Codes, Furnace, Hvac

Lennox Furnace Code E207 — Hot surface igniter open | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Lennox Furnace Code E207 — Hot surface igniter open | BC Wide

Lennox Furnace Code E207 — Hot surface igniter open | BC Wide

Quick answer

Lennox furnace error code E207 means the control has found the hot surface igniter circuit open, so the igniter cannot glow and the burners cannot light (confirm the exact wording against the manual for your unit). In practice you have no heat until it is repaired. Check power, the thermostat call and one reset only if your manual allows it, then call a licensed gas technician. Most often the igniter itself has cracked or burned out; a wiring or connector fault is the next most likely cause.

If your Lennox furnace is showing E207 (Hot surface igniter open), here’s exactly what it means and what to do. This guide is part of our full Lennox furnace error code list.

Severity: Needs attention.

What E207 means on a Lennox furnace

iComfort: the furnace hot surface igniter circuit is open (resistance out of the specified range). The igniter typically needs replacement.

Common causes

  • Cracked or burned-out hot surface igniter
  • Open igniter wiring/connection

What you can safely check first

  1. No safe homeowner action — the igniter is a fragile ceramic part inside the burner compartment
  2. Schedule a technician to measure and replace the igniter

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Lennox furnace usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver furnaces since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Lennox furnace repair across Greater Vancouver

If a Lennox furnace showing E207 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast furnace repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Lennox furnace codes

Frequently asked questions

Is E207 on a Lennox furnace serious?

It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs Lennox furnaces 7 days a week across Greater Vancouver.

How do I reset a Lennox furnace after E207?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Lennox furnace error code E207: what it means for you at home

In owner words, E207 tells you the furnace tried to start a heating cycle, checked the igniter circuit, and found it open: electrically broken, or reading outside the resistance range the control expects. The control will not open the gas valve to an igniter it cannot prove, so the furnace stops before any gas flows. That is the safety design doing its job. The meaning is exactly what the opening of this page states; confirm the wording against the manual for your unit, because display text can vary between control generations.

What it means for heat: the house will cool down and stay cool until the circuit is repaired. The blower may still run on its own if the thermostat fan is set to on, which can feel like the furnace is working while it moves room-temperature air. What it means for hot water: a gas furnace does not heat your domestic hot water, so your water heater carries on normally unless something shared has changed, such as a closed main gas valve. What it means for safety: an open igniter circuit is not in itself a gas leak or a carbon monoxide event, but it does mean the appliance needs a licensed person working inside the burner compartment.

Why it happens: a hot surface igniter is a ceramic element that heats to a bright glow every time the furnace starts. Thousands of heat-and-cool cycles slowly weaken it, and it eventually cracks or burns open. That is why E207 so often shows up on the first cold morning of the season, after the furnace has sat idle all summer and the first start-up puts stress on an element that was already tired.

Symptoms owners usually describe to us:

  • The thermostat is calling for heat but the house keeps getting colder.
  • You hear the small inducer fan start, run for a while, then stop, sometimes trying again before the furnace gives up.
  • There is no orange glow through the sight window where you would normally see one just before the burners light.
  • The furnace display or the thermostat shows E207 or reports a furnace fault.
  • The fan blows air that is not warm.
  • The problem started right after the first heating call of the season or after a power interruption.

Lennox furnace error code E207 causes, most common first, and the checks you can safely do

These are ranked from what we find most often on Greater Vancouver service calls to what we find least often. The owner-safe column is deliberately short: almost everything that causes E207 sits behind the burner compartment door, which is licensed-technician territory. Your checks are about ruling out the simple things and giving the technician good information, not about fixing the igniter.

What you should not do: do not remove the burner compartment door, do not touch or tap the igniter, do not jumper or bypass any switch, and do not keep cycling power. The igniter is a brittle ceramic part; a fingertip can crack a weak one, and skin oils can shorten the life of a new one. Repeated resets do not repair an open circuit and can hide a second fault the technician needs to see.

Safety line: if you smell gas (a rotten-egg odour) or your carbon monoxide alarm sounds, get everyone out of the house now, do not operate light switches or appliances on the way out, and call FortisBC or 911 from outside. E207 on its own is not a gas leak, but if either of those signs appears, the error code stops mattering and safety comes first.

  • Power: confirm the furnace service switch (often a light-style switch on or near the unit) is on and the breaker has not tripped. Reset a tripped breaker once only; if it trips again, leave it off and call us.
  • Gas supply: confirm the manual shut-off valve on the gas line to the furnace is open, with the handle in line with the pipe. Do not operate any other valve and never touch the gas valve on the furnace itself.
  • Thermostat: make sure it is set to heat and a few degrees above room temperature, and replace its batteries if it uses them.
  • One reset, only if your owner manual allows it: switch the furnace off, wait a minute, switch it back on and watch one attempt. If E207 returns, stop there.
  • Outside terminals: on a high-efficiency furnace, check that the intake and exhaust pipes outside are clear of snow, leaves, cobwebs or nests. A blocked terminal does not cause E207, but it causes other lockouts we want to rule out.
  • Condensate drain: look at the visible drain tubing and the floor drain or condensate pump for a disconnected hose or pooled water, and tell us what you see.
Likely cause (most common first)What it usually looks likeWhat you may safely checkWhen it becomes a licensed call
1. Cracked or burned-out hot surface igniterNo glow at all; E207 returns on every start attemptNothing on the igniter itself. Confirm power and a thermostat call so the technician knows the fault is realAlways. Measuring and replacing the igniter is work inside a gas appliance
2. Loose, corroded or heat-damaged igniter connector or wiringCode comes and goes, sometimes clearing after the furnace sits for a whileWrite down when it happens, for example after a cold night or a power blipAlways. Wiring between the igniter and the control is inside the cabinet
3. Incorrect or poorly fitted replacement igniter from an earlier repairCode returns soon after a recent igniter replacementFind the paperwork from the last repair so we can see what was installedAlways. The part must match what the manufacturer specifies for your model
4. Moisture reaching the igniter wiring from a condensate leakWater staining or drips in or under the furnace around the time the code appearsLook at the visible condensate tubing and drain for a disconnected hose or water on the floor. Do not open panelsAs soon as water is near wiring or the code persists
5. Control board fault in the igniter circuit (less common)A sound igniter and good wiring, but the circuit still reads wrongNoneAlways. Board diagnosis needs meters and the manufacturer wiring diagram

How our Lennox E207 repair visit works, step by step

This is what a correct E207 visit looks like from the moment you call. If you are comparing contractors, it is also what you should expect anyone working on your furnace to do.

  • Step 1, booking: we ask for the exact code, the furnace age if you know it, and what happened just before the fault. We book same-day where we can; in a cold snap the schedule fills quickly, and we will tell you the honest earliest window rather than promise an arrival time.
  • Step 2, fault history: the technician reads the stored fault history on the control. A furnace that has logged repeated ignition faults over weeks tells a different story from a single event, and it points to wiring or a failing part rather than bad luck.
  • Step 3, isolate and measure: with power isolated, the technician measures the igniter resistance with a meter and compares it to the manufacturer-published range for your model, then inspects the harness and connector for heat damage, corrosion or a loose terminal.
  • Step 4, check the supply side: with power restored, the technician confirms the control is actually sending voltage to the igniter during the ignition sequence. That one measurement separates a bad igniter from a wiring or board problem, and it is what stops a contractor from replacing the wrong part.
  • Step 5, written quote: before any work beyond diagnosis, you get a written quote naming the part and the labour. Nothing is replaced on a guess.
  • Step 6, repair: the parts most often involved are the hot surface igniter itself, the igniter wiring or connector, and less often the integrated control board. The replacement is the igniter specified for your furnace, handled by its base only and mounted so it sits correctly against the burner.
  • Step 7, prove the safeties: after the repair the technician runs full ignition cycles, confirms the flame is proven, cleans or checks the flame sensor, checks high-limit and pressure switch operation, verifies gas pressure against the rating plate, and tests for carbon monoxide at the flue and in the living space.
  • Step 8, paperwork: you receive a written invoice listing what was measured, found and replaced, plus anything we noticed that is wearing but not yet failing, so you can plan instead of being surprised next winter.

Repair or replace an older Lennox furnace with an E207 code?

On most furnaces, E207 is a repair, not a reason to replace. An igniter is a wear part, and changing it on an otherwise sound furnace is normal service. On cost, without numbers: a hot surface igniter is usually one of the less expensive repairs on a gas furnace, while an integrated control board is one of the more expensive parts. That gap is exactly why measuring before replacing matters, and why the quote comes in writing first. The question only changes when the igniter is the latest in a run of failures on an older unit.

If replacement is on the table, we lead with dual fuel: a heat pump that carries the heating load through most of our mild coastal winter, paired with a new high-efficiency gas furnace that takes over during cold snaps. The furnace stays as genuine backup, so a single component failure or a deep freeze does not leave the house cold. We lay out a straight repair option and a replacement option side by side in writing, and there is no pressure to decide on the day. A furnace replacement or a new heat pump needs permits and an inspection, which we pull through the authority that covers your address.

  • Repair usually makes sense when the furnace is mid-life, the burners and heat exchanger inspect clean, and this is the first ignition fault in a long time.
  • Replacement is worth discussing when the furnace is near the end of its expected service life, has needed several significant repairs in recent seasons, or parts for its control are becoming hard to source.
  • A cracked or failing heat exchanger found during the visit changes the decision immediately; we show you what we found and put it in writing.
  • Comfort complaints that predate E207, such as uneven rooms, noisy ducts or rising gas bills, suggest the whole system deserves a look, not just the igniter.
  • If you already plan to add cooling, a dual-fuel heat pump can solve the heating question and the cooling question in one project.

Lennox furnace error code E207 repair near you in Greater Vancouver

We service Lennox furnaces showing E207 across Greater Vancouver from our Burnaby base. Housing stock affects how an igniter job goes, mostly through access to the furnace, the venting layout and the age of the wiring, so here is what we commonly run into. These are general patterns, not rules for any particular street or home.

In strata townhomes and apartments with their own gas furnace, we confirm access arrangements and what the strata allows before any change to venting or equipment. Timing anywhere in the region is same-day where we can, depending on the day’s calls and your location; we will never promise a guaranteed arrival window we cannot keep.

  • Vancouver: many older detached homes with furnaces in tight basement mechanical rooms or crawlspaces, plus newer infill and laneway homes with compact closet installs. Access can take longer than the repair itself.
  • Burnaby: a broad mix of post-war houses that have been through several furnace generations and newer townhomes with closet or garage furnaces. Older wiring runs deserve a careful look.
  • Surrey: many newer subdivisions with high-efficiency furnaces, which means plastic venting, condensate drains and outdoor terminals near decks and gardens that collect debris.
  • Richmond: many homes are built without full basements, so furnaces are often in garages, closets or attic spaces, and condensate routing matters.
  • Coquitlam and the Tri-Cities, including Port Coquitlam and Port Moody: hillside and split-level homes where the furnace may sit in a lower level or crawlspace, with side-wall terminals facing heavy leaf fall.
  • The North Shore, North Vancouver and West Vancouver: damp, sloped lots and dense foliage, so we always check the outdoor intake and exhaust terminals and moisture around the appliance.
  • New Westminster: older character homes alongside townhomes and strata buildings, with some tight mechanical spaces.
  • Delta, including North Delta, Ladner and Tsawwassen: a mix of older ranchers and newer builds, with garage and crawlspace installs common in some areas.
  • Langley: newer subdivisions and larger lots, with attic, garage and basement furnaces all in the mix.

Who should fix Lennox furnace error code E207: an independent TSBC-licensed contractor

BC Wide Home Services Ltd is an independent gas contractor licensed by Technical Safety BC (gas contractor licence LGA0090068, Class B gas licence CGA0028029), serving Metro Vancouver from Burnaby since 1999. We are not a Lennox dealer, an authorized dealer or a warranty centre for any manufacturer. Lennox is a brand we service, alongside the other furnace brands common in local homes.

Furnace brands we service include Lennox, Carrier, Bryant, Trane, American Standard, Goodman, Amana, Rheem, Ruud, York, Daikin and KeepRite.

What you should see from us, in writing where it matters:

  • Diagnosis and repair by our own licensed gas fitters, not subcontractors.
  • Measurements before any part is ordered, so the fix targets the real fault.
  • A written quote before any work beyond diagnosis.
  • Permits and inspections pulled by us when the job needs them, such as a furnace replacement or a new heat pump.
  • A written invoice showing what was measured, found and replaced, and what to watch for next.
  • Straight answers on warranty: if your furnace may still have parts coverage, keep your registration and installation records handy. The manufacturer sets the terms, and we can tell you what paperwork a claim usually needs. Call (604) 473-9690 to book an E207 diagnosis.

More questions homeowners ask

What does Lennox furnace error code E207 mean?

It means the furnace control has detected that the hot surface igniter circuit is open, with resistance outside the range it expects, so it will not try to light the burners. The most common reason is a cracked or burned-out igniter, followed by a loose or damaged connector or wire. Confirm the exact meaning against the manual for your unit.

Can I reset a Lennox furnace with error code E207?

You can try one reset by switching the furnace off and back on, but only if your owner manual allows it. If E207 comes back on the next attempt, stop resetting, because an open igniter circuit does not repair itself and repeated cycling can hide other faults. Book a licensed technician to measure the circuit.

Is it safe to run my Lennox furnace with an E207 code?

The furnace will not light while E207 is active, so it is protecting you by refusing to open the gas valve. Do not try to force it to light or bypass anything to get heat. If you smell gas or a carbon monoxide alarm sounds, leave the house and call FortisBC or 911 from outside.

Can I replace the hot surface igniter on my Lennox furnace myself?

No. In BC, work inside a gas appliance’s burner and ignition system belongs to a licensed gas fitter, and a homeowner should not open the burner compartment. The igniter is fragile, must match the manufacturer specification for your model, and the repair must be followed by proving the safeties and testing for carbon monoxide.

How long does a Lennox E207 repair take?

When the igniter is the cause and the correct part is available, the repair is normally finished in a single visit. Tight crawlspace or attic access, a wiring repair, or a control board that has to be ordered can extend that. We tell you which situation you are in at diagnosis, before any work beyond it.

Who repairs Lennox furnace error code E207 near me in Greater Vancouver?

BC Wide services Lennox furnaces in Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We are an independent TSBC-licensed contractor, not a dealer, and we book same-day where we can. Call (604) 473-9690 for an honest earliest window.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a furnace be serviced?
Annual servicing is recommended for gas furnaces, ideally before the start of the heating season in September or October. Service includes burner cleaning, heat exchanger inspection, ignition check, blower motor cleaning, gas pressure adjustment and a full safety test for carbon-monoxide leaks.
How long does a furnace last in Vancouver's climate?
High-efficiency gas furnaces typically last 15–20 years with annual maintenance. Vancouver's mild climate means lower run-times than colder Canadian cities, which extends life — but salt-air corrosion near the coast and high humidity can shorten it.
Why is my furnace blowing cold air?
Common causes are a thermostat set to "on" instead of "auto", a tripped flame sensor, a clogged condensate drain shutting down a high-efficiency unit, low gas pressure, or a failed ignitor. Most are repairable in a single service visit.
How much does a new furnace cost in Vancouver?
A typical residential high-efficiency gas furnace in Metro Vancouver costs $4,500–$8,500 installed depending on size, brand and venting requirements. Variable-speed and modulating models are at the upper end.
What is the most reliable furnace brand?
In our experience servicing Vancouver homes since 1999, Carrier, Lennox, Bryant and York have produced the most reliable mid-to-high-efficiency furnaces with the best parts availability. Goodman and Rheem offer strong value at lower price points.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote