★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

What a Navien Combi Boiler Replacement Costs in Metro Vancouver

Boilers

What a Navien Combi Boiler Replacement Costs in Metro Vancouver
Home › What a Navien Combi Boiler Replacement Costs in Metro Vancouver

What a Navien Combi Boiler Replacement Costs in Metro Vancouver

Key takeaways

  • A ballpark installed range for a gas combi boiler replacement in Greater Vancouver is $8,000 to $14,000 and up, before GST and before any rebate. That is orientation only, not a quote.
  • The unit itself is usually the smaller half of the number. Venting, gas line capacity, condensate routing, electrical, permits and removal of the old appliance carry most of the variation.
  • A bare swap and a complete job can look like the same line on paper. The difference shows up in what the quote does not mention: vent material and route, gas sizing calculation, system flush, isolation valves, commissioning and inspection.
  • Sizing should follow a heat loss calculation and a realistic hot water demand, not simply matching whatever was on the wall before.
  • Metro Vancouver water is soft, so the hydronic side here suffers from sludge and corrosion rather than limescale, which makes a proper flush and a good filter worth paying for.
  • BC Wide is an independent TSBC-licensed contractor (LGA0090068, CGA0028029). We install and service this equipment. We are not a factory-authorised dealer or warranty centre for any brand.

For a Metro Vancouver home, a ballpark installed range for replacing a gas combi boiler with a Navien unit is $8,000 to $14,000 and up, before GST and before any rebate. Those are ballpark figures for orientation only. They are not a quote, and an accurate price needs a site visit, because the appliance is only part of what you are buying. The rest is the work around it: where the exhaust and intake can legally run, whether the existing gas line can carry the firing rate of a combi unit that has to make heat and domestic hot water, where the acidic condensate goes, what the electrical supply looks like, how the old boiler comes out of a tight mechanical room, and what the municipality wants to see before the permit closes. Two contractors can quote the same Navien appliance and land thousands apart because one of them has priced all of that and the other has priced a swap. This page explains what sits inside the range, what pushes a job to the top of it, and how to read two quotes so the cheaper one is not simply the one leaving work out.

What does a Navien combi boiler replacement cost in Metro Vancouver?

The ballpark installed range for a gas combi boiler replacement in the Lower Mainland is $8,000 to $14,000 and up, before GST and before any rebate. Again, that is a ballpark for orientation and not a quote. A straightforward job at the low end usually means the new unit lands in the same spot as the old one, the existing vent route can be reused or easily re-run in the correct material, the gas line already has capacity, there is a drain nearby for condensate, and the mechanical room has room to work. Jobs at the top of the range and above involve one or more of those conditions failing.

If you are replacing a conventional condensing boiler rather than a combi, the comparable ballpark range is $7,000 to $15,000 installed, because a heating-only boiler is often paired with an existing tank or an indirect cylinder, and the cost shifts depending on what happens to that tank. Combi units fold space heating and domestic hot water into one appliance, which is why they are popular in townhomes, strata units and older homes where mechanical space is scarce. It is also why the domestic hot water side of the job, the piping, the isolation valves and the flow rate expectation, has to be part of the conversation rather than an afterthought.

One thing worth saying plainly: the price of the appliance is rarely what separates two quotes. Labour hours, materials for the vent and gas work, and the scope a contractor is willing to write down are what move the number. When a quote comes in far under everything else you have seen, the useful question is not why it is cheap but what it covers.

What is actually included in a complete combi boiler installation?

A complete job is a list of tasks, not a single line item. When you read a quote, you are really checking whether each of the following has been thought about and priced. If a task is missing from the page, it will either be skipped or it will arrive later as an extra.

The table below sets out the components of a typical combi boiler replacement and what each one is for. It is a reasonable checklist to hold a quote against, regardless of which brand you have chosen.

Part of the jobWhat it coversWhy it affects the price
Heat loss and sizingCalculating the home’s actual heating load and the hot water demand before choosing an outputAn oversized unit short cycles and wears; a properly sized one may cost more or less than the old appliance
Removal and disposalDraining, disconnecting and carrying out the old boiler, plus recycling or disposal feesTight stairs, crawl spaces and strata access rules turn a one-hour task into a half day
VentingNew sealed intake and exhaust in the manufacturer-specified material, terminated at a code-compliant locationRoute length, wall or roof penetrations, clearances from windows and property lines, and fire separations all add labour
Gas supplyConfirming or upsizing the gas line so the unit gets full firing rate under loadA long or undersized run, or several appliances on one line, means new pipe and more labour
Condensate handlingRouting acidic condensate to an approved drain, with neutralisation where requiredNo nearby drain means a condensate pump and a longer run
Electrical supplyA dedicated, correctly protected circuit and bonding for the appliance and controlsAn older panel with no spare capacity adds licensed electrical work
Hydronic connectionsNear-boiler piping, isolation and service valves, expansion tank, air and dirt separation, relief pipingReusing tired valves saves an hour now and costs a service call later
System flushCleaning sludge and debris out of the existing loop before the new heat exchanger sees itOld cast iron or steel systems need more work; skipping it risks the new appliance
Controls and thermostatWiring the thermostat, outdoor reset sensor where used, and setting up the control strategyModulation and outdoor reset need commissioning time to be worth anything
Permit and inspectionGas permit and inspection through the authority having jurisdictionFees are set by each municipality or Technical Safety BC, and inspection time is real labour
CommissioningCombustion check, gas pressure verification, purging air, setting temperatures and documenting resultsThis is the step that most often distinguishes two otherwise identical quotes

What site conditions push the price to the top of the range?

Most of the spread in the ballpark range comes from the building, not the boiler. The following conditions reliably add hours, materials, or both.

None of these are upsells invented at the kitchen table. They are things a technician can see during a site visit, which is precisely why a firm number over the phone is not possible for this kind of work.

  • Venting that cannot reuse the old path. A condensing combi needs sealed intake and exhaust in the material the manufacturer specifies, terminated where it will not re-enter the building or a neighbour’s opening. Moving a termination to satisfy clearances can mean new penetrations, patching and sometimes scaffolding.
  • A gas line that is undersized for the new firing rate. A combi has to satisfy space heating and a full hot water draw, so the demand at the appliance can be higher than what the old unit needed. Running new pipe is a ballpark $500 to $1,500 where the route is short and accessible, and $1,500 to $3,000 or more where it is long or difficult.
  • No drain within reach of the appliance. Condensate is acidic and has to be handled properly, which may mean a pump, a longer route, and neutralisation media.
  • An electrical panel with no room. Adding a circuit is straightforward when there is a spare slot and much less so when there is not. Panel work is licensed electrical work.
  • Difficult access. Crawl spaces, narrow basement stairs, a mechanical closet built around the old boiler, or a strata building with elevator booking and restricted work hours all add time.
  • Distribution that needs attention. Failing zone valves, a seized circulator, an undersized expansion tank or radiators that were never balanced will not be fixed by a new appliance, and a good contractor will price them rather than ignore them.
  • Code upgrades triggered by the work. Once the appliance is replaced, clearances, combustion air, seismic strapping of nearby equipment and CO alarm placement all have to meet current requirements.

Which choices inside the Navien lineup change the number?

Navien is a brand we service as an independent contractor, and like most manufacturers it offers combi boilers in more than one output and more than one configuration. Rather than quote model names or figures we cannot verify for your specific unit, here is what genuinely moves cost between one Navien combi and another.

Output is the first lever. A larger unit costs more to buy and sometimes more to vent and supply with gas. The right output comes from a heat loss calculation and an honest look at your hot water pattern, such as how many bathrooms are likely to run at once. Bigger is not better; an oversized combi short cycles on space heating and is harder on itself.

The domestic hot water arrangement is the second. Some combi setups are paired with a small buffer or storage arrangement to smooth out draws, and some include or accommodate recirculation so hot water reaches a distant fixture faster. Recirculation is worth understanding before you commit, because there are three different things people mean by it: a pump built into the appliance, an external pump on a dedicated return line back to the appliance, and a crossover or bypass-valve retrofit that uses the cold line as the return when no dedicated return exists. The first is simplest, the second performs best and costs the most to pipe in an existing house, and the third is the common retrofit compromise. Which one you choose changes both the material list and the labour.

Controls are the third. Outdoor reset, modulation behaviour, zoning and how the thermostat talks to the appliance all affect how well a modulating combi actually modulates. Setting these up properly takes commissioning time, and that time is part of the price.

Whatever the configuration, verify capacity, efficiency rating and clearance requirements against the rating plate on the unit and the manufacturer’s own documentation. Those numbers are manufacturer-published, and you or your installer should confirm them for your exact model rather than taking a figure from a sales page.

Which line items are quoted separately, and why?

Some items are genuinely outside the installed price and should appear as their own lines rather than being buried. Seeing them listed separately is a sign of a careful quote, not a padded one.

You will notice there are no dollar figures attached to several of these. That is deliberate. Rebate and incentive programs change, fees are set by others, and financing terms depend on the lender, so any number we printed here would be wrong by the time you read it. Ask for those in writing, from the program or the municipality, at the time you commit.

  • Permit and inspection fees, which are set by each municipality or by Technical Safety BC and are not ours to set or discount.
  • Rebates, incentives and grants, which are applied for separately, have their own eligibility rules and documentation requirements, and should never be treated as a discount on the invoice.
  • Financing, which is arranged with a lender on its own terms rather than being part of the installed price.
  • Electrical work by a licensed electrician where a new circuit or panel capacity is required.
  • Drywall, painting and finish repairs around new penetrations, which many mechanical contractors do not carry in scope.
  • Asbestos or vermiculite assessment and abatement in older homes where the work area is disturbed.
  • Distribution repairs discovered once the system is open, such as failing zone valves or a seized circulator.
  • Annual maintenance after the first year, and the service-call or diagnostic fee structure, which are separate from the installation and should be described in writing without being bundled into the install price.
  • GST, which is added to the installed price, and which is why every range on this page is quoted before tax.

What does Metro Vancouver specifically add to a combi boiler job?

Our climate and our housing stock change this job in ways that are easy to overlook if you are reading advice written for somewhere else.

The water here is soft. That matters because the mineral scaling that dominates boiler advice from harder-water regions is much less of a story locally. What we see instead on the hydronic side is sludge and corrosion: magnetite and debris that build up in older loops and then get pulled through a brand new heat exchanger the first time the circulator runs. This is why a proper flush, good air and dirt separation and in many cases a magnetic filter are worth paying for here, and why a quote that skips the flush is taking a risk with your new appliance rather than saving you money.

The climate is mild and wet, and a large share of the heating season is spent at outdoor temperatures well above design conditions. A modulating combi that is correctly sized and set up with outdoor reset spends most of the year running long, low, quiet cycles, which is where condensing efficiency actually lives. An oversized unit with a crude control strategy spends the same season starting and stopping. The equipment cost difference between those two outcomes is often nothing; the difference is the sizing calculation and the commissioning.

The housing stock is a mix of postwar homes, 1970s and 1980s builds, and dense strata. Older homes frequently have gas lines sized for a different era of appliance and mechanical rooms that were finished around the existing boiler. Strata buildings add rules: common-area venting, scheduled work hours, elevator bookings, and in many cases strata approval before anything is touched. Townhomes often have the boiler in a closet with a door width that decides how the old unit leaves and the new one arrives. None of this is unusual, but all of it costs hours, and it is the main reason a Vancouver number is not a national number.

Wet coastal weather also matters for terminations. Vent terminations, condensate routes and any exterior penetrations have to be detailed so that driving rain does not find its way in, and so snow or debris cannot block an intake during a cold snap.

How do you compare two Navien combi quotes side by side?

If two quotes name the same appliance and differ by several thousand dollars, the difference is scope, not the box. Put them next to each other and look for the following.

A helpful test: ask each contractor what happens if the gas line turns out to be undersized, or if there is no drain for condensate. A quote built on a real site visit will already have an answer, because the technician looked. A quote built on a phone call will discover it on install day, and you will be the one holding the change order.

  • Does it state the venting material and the route, or just say venting? Vent work is one of the largest labour variables in the job.
  • Does it confirm the gas line is adequate, or note that sizing will be verified? If neither quote mentions gas capacity, neither has priced it.
  • Does it say where the condensate goes and whether a pump or neutraliser is included?
  • Does it include a system flush, new isolation and service valves, and an expansion tank assessment, or does it reuse whatever is there?
  • Does it include the permit and the inspection, or is the permit listed as something you arrange?
  • Does it include commissioning with a combustion check and documented gas pressures? This is the step that most often disappears from a low quote.
  • Does it state the output being installed, and is that output backed by a heat loss calculation rather than a match to the old unit?
  • Does it name the licences the work is performed under? Gas work in BC must be performed by a licensed gas fitter working under a licensed contractor.
  • Is warranty coverage described as the manufacturer’s published terms plus the contractor’s own labour warranty, and are the two clearly separated? Verify manufacturer terms in the documentation that comes with your unit and register the appliance as instructed.

When should you call a licensed technician rather than handling it yourself?

Gas work and most electrical work in British Columbia are legally restricted to licensed trades. A homeowner may reasonably check a thermostat’s batteries and settings, read the pressure gauge on the boiler, look at whether the vent terminations outside are clear of snow, leaves or nesting material, confirm that isolation valves are not accidentally closed, and note any error indication on the display so it can be reported accurately. A homeowner may also keep the area around the appliance clear and make sure carbon monoxide alarms are present and tested.

Everything else on a combi boiler belongs to a licensed technician: gas connections and pressure testing, combustion analysis, venting, condensate and relief piping, control wiring, heat exchanger service, and any diagnosis that involves opening the appliance. Do not attempt to reset a locked-out appliance repeatedly, and do not bypass a safety device. If you smell gas, do not operate switches; leave the building and call from outside.

Call a licensed contractor promptly if the boiler locks out repeatedly, if you see soot, scorching or water staining near the appliance or vent, if the relief valve is discharging, if a carbon monoxide alarm sounds, or if the unit is making heat but domestic hot water has become unreliable. Same-day attendance is sometimes possible depending on the day and the crew’s load, and sometimes it is not; we will tell you honestly which it is rather than promise an arrival window we cannot keep. BC Wide is a TSBC-licensed contractor in Burnaby serving Metro Vancouver since 1999, licences LGA0090068 and CGA0028029. To talk through a replacement or book a site visit, call (604) 473-9690.

Gas & carbon-monoxide safety: A combi boiler is combustion equipment. Natural gas appliances produce carbon monoxide, an odourless gas that can be fatal, and a blocked, damaged or incorrectly terminated vent is the most common cause of a problem. Install working carbon monoxide alarms on every level of the home and near sleeping areas, test them regularly, and replace them at the manufacturer’s stated end of life. If a carbon monoxide alarm sounds, leave the building and call for help from outside. If you smell gas, do not operate light switches, appliances or phones inside: leave immediately, then call your gas utility’s emergency line from a safe location and call (604) 473-9690 once the building is safe. Gas connections, pressure testing, venting and combustion adjustment must be performed by a licensed gas fitter, and electrical work by a licensed electrician. Never bypass a safety control or repeatedly reset an appliance that keeps locking out, because the lockout is protecting you.

Frequently asked questions

Why can nobody give me a firm price over the phone?

Because the appliance is the predictable part and the building is not. Vent route, gas line capacity, condensate drainage, electrical supply and access can each add hours or materials, and none of them can be assessed by phone. A ballpark range like $8,000 to $14,000 and up for a combi replacement is useful for planning, but it is not a quote, and an accurate number requires a site visit.

Is a combi boiler the right choice, or should I keep a separate water heater?

A combi makes sense when mechanical space is tight and the hot water demand is moderate and predictable, which describes a lot of Metro Vancouver townhomes and strata units. A separate boiler and storage arrangement can suit larger homes with several bathrooms running at once, or homes where the heating load and the hot water load are very different in size. The right answer comes from a heat loss calculation and an honest look at how your household actually uses hot water.

Does the price change much between Navien and another brand of combi boiler?

Less than most homeowners expect. Across reputable condensing combi brands, the appliance is a minority of the installed cost, and the venting, gas, condensate, electrical and commissioning work is broadly similar. Parts availability, local service familiarity and the manufacturer’s published warranty terms are usually more useful comparison points than list price. BC Wide services this equipment as an independent contractor and is not a factory-authorised dealer for any brand.

Do I need a permit to replace a combi boiler in Metro Vancouver?

Yes. Gas appliance replacement requires a permit and inspection through the authority having jurisdiction, which is either your municipality or Technical Safety BC depending on where you live. Fees are set by that authority, not by the contractor. A quote that does not mention the permit is a quote you should ask about directly, because an unpermitted install can create problems at resale and with insurance.

Will my existing radiators or in-floor loops work with a new combi?

Usually yes, but they need to be assessed rather than assumed. The important questions are whether the distribution can deliver enough heat at the lower water temperatures a condensing boiler prefers, whether zone valves and circulators are still sound, and whether the loop is full of sludge from years of running. Because our water is soft, corrosion products rather than limescale are the usual problem, which is why a flush and proper dirt separation are worth including.

How long does the installation take?

A same-for-same replacement with a reusable vent route and adequate gas supply is commonly a one-day job, with the inspection following separately. Jobs that involve new venting, a gas line upgrade, condensate routing or electrical work run to two days or more. Strata buildings often add a day simply because of access scheduling and approvals, so build that into your planning rather than your budget.

What should I ask a contractor before signing?

Ask what output is being installed and what calculation it came from, what vent material and route are planned, whether the gas line has been verified for capacity, where condensate will go, whether the permit and commissioning are included, and who performs any electrical work. Ask for the licences the work is performed under. If two quotes differ substantially, these questions almost always explain the gap.

Can I add hot water recirculation at the same time?

Often yes, and doing it during the replacement is cheaper than coming back later. There are three approaches with different costs: a pump built into the appliance, an external pump on a dedicated return line back to the unit, and a crossover or bypass-valve retrofit that uses the cold line as a return where no dedicated return exists. A dedicated return performs best but requires pipe to be run, so in an existing house the retrofit approach is frequently the practical choice.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote