★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Noritz EZ Series Tankless Water Heater Installation and Replacement

Water Heaters

Noritz EZ Series Tankless Water Heater Installation and Replacement
Home › Noritz EZ Series Tankless Water Heater Installation and Replacement

Noritz EZ Series Tankless Water Heater Installation and Replacement

Key takeaways

  • A Noritz EZ Series install is decided by three things in your house: whether the gas line can carry the unit’s input, where the venting can terminate, and where the condensate can drain.
  • Noritz positions the EZ Series around replacing a gas tank water heater with less re-piping, but an older Metro Vancouver home still needs a site survey before anyone promises a simple swap.
  • Every rating, input, vent length and pipe size for your unit is manufacturer-published; check the rating plate and the installation manual rather than trusting a generic figure.
  • Gas work, venting and the electrical connection must be done by licensed trades, under a gas permit, with the installation open to a Technical Safety BC inspection.
  • Commissioning should include a gas-pressure check under full fire, a combustion analysis, a leak test and a hot-water temperature check at the fixtures.
  • At handover you should receive the permit number, combustion readings, the model and serial number, the manual and clear descaling and maintenance instructions.

A correct Noritz EZ Series tankless installation in a Metro Vancouver home starts with a site survey, not a box on the floor. The installer confirms your household’s hot-water demand, checks that the gas supply can feed the unit at full fire alongside your furnace or boiler, plans a vent route that meets code and the manufacturer’s clearances, finds a place to drain condensate, and decides how recirculation will work. Then the old gas tank water heater is removed, the EZ Series unit is mounted, gas, water, vent, condensate and power are connected, and the job is commissioned with a gas-pressure check and a combustion analysis before it is signed off under a gas permit and open to a Technical Safety BC inspection. Noritz markets the EZ Series around making the move from a tank easier, and in many Lower Mainland homes it is, but the survey is what tells you whether your swap is straightforward or needs gas-line and venting work first. BC Wide Home Services is an independent TSBC-licensed contractor (LGA0090068, CGA0028029) that services and installs this family; we are not a factory-authorised dealer or warranty centre, and we give a written quote before any work begins.

What is different about installing a Noritz EZ Series unit compared with other tankless heaters?

The EZ Series is the Noritz family aimed squarely at people replacing a gas tank water heater. The pitch is that the unit is laid out so the hot and cold connections sit where a tank’s usually do, which can cut down on the re-piping that a conventional wall-hung tankless demands. In practice that means the water side of the job is often simpler than with other tankless designs, while the gas and venting sides are exactly as demanding as any other condensing tankless install.

Because the EZ Series is a condensing design in the configurations we typically see, it produces acidic condensate that has to be drained or neutralised, and its flue gases are cool enough that it uses plastic vent materials approved in the manual rather than the metal B-vent or chimney a tank used. That single fact is why a so-called easy swap is rarely a pure like-for-like: the old vent usually cannot be reused, and a new vent route has to be planned. Confirm the approved vent materials and configurations for your exact unit in the installation manual.

The honest summary: the EZ Series can reduce plumbing changes, but it does not remove the gas-supply question, the venting question or the condensate question. Those three decide the scope of the job in most Lower Mainland homes.

How do you size a Noritz EZ Series for my household?

Tankless sizing is about flow at a temperature rise, not tank volume. We start with a demand assessment: how many showers can run at once, whether there is a soaker tub, whether the dishwasher and laundry run while people shower, and how many bathrooms are on the system. We then compare that peak simultaneous demand against the unit’s manufacturer-published flow capability at the temperature rise your incoming water needs.

In Metro Vancouver the incoming water is cold for much of the year, especially in winter when the reservoirs and mains are at their coldest. A unit that keeps up comfortably in August can feel undersized in January if nobody accounted for that larger temperature rise. We size for the cold months, not the warm ones.

If the demand assessment shows your household regularly runs more hot water at once than one unit can deliver at a winter temperature rise, we will say so plainly and discuss options such as staggering high-demand fixtures or a different configuration. We do not quote capacity or flow figures from memory; the numbers for your model are on the rating plate and in the manual, and we work from those.

What happens during the site survey before a Noritz EZ Series install?

The survey is where the job is really decided. Everything in the table below is checked before we write a quote, because each item can change the scope, the timeline or whether a replacement can happen on the day you want.

What we checkWhy it mattersWhat it can lead to
Gas meter and existing gas line sizingA tankless unit draws far more gas at full fire than a tank, and it shares the line with your furnace, boiler, range or fireplaceReusing the existing line, upsizing a section of pipe, or a meter change request to the gas utility
Vent route and termination locationCondensing flue gas must exit through approved vent material with clearances from windows, doors, soffits, property lines and air intakesSidewall venting, roof venting, or relocating the unit to a wall that allows a compliant termination
Condensate drainageCondensate is acidic and must go to an approved drain, often through a neutraliserGravity drain to a floor drain or standpipe, or a condensate pump where no drain is nearby
Electrical supplyThe unit needs power for its controls, fan and freeze protectionUsing a nearby receptacle or adding a dedicated circuit by a licensed electrician
Water piping and shut-offsIsolation valves are needed for future descaling and serviceInstalling an isolation valve kit with service ports on the hot and cold lines
Existing recirculation or long pipe runsTankless units behave differently from tanks when a recirculation loop is presentChoosing a built-in pump, external pump on a return line, or a crossover valve retrofit
Mounting location and clearancesThe unit needs service clearances and must be reachable for maintenanceWall reinforcement, relocating from a tight closet, or confirming the old tank location works

What is the sequence of a Noritz EZ Series replacement on installation day?

Once the survey and permit are in place, a typical replacement follows a consistent order. Some steps are fast and some depend on what the survey found, but skipping any of them is how installations end up with nuisance lockouts, poor hot water or failed inspections.

  • Shut off gas to the old tank water heater, isolate the water, and drain the old tank safely before disconnecting it.
  • Disconnect and cap the old gas connection, remove the old vent connector, and properly deal with the old vent or chimney opening so it is not left as an open path.
  • Mount the EZ Series unit to the manufacturer’s clearances, with wall support where needed.
  • Run or modify the gas supply to the unit with a manual shut-off and sediment trap as code requires, sized to the input shown on the rating plate.
  • Install the vent and combustion-air piping in the approved material, with correct slope back toward the unit and supports at the spacing the manual requires, terminating at a compliant location.
  • Connect cold and hot water through isolation valves with service ports, plus the pressure-relief arrangement the manual specifies.
  • Pipe the condensate drain, including a neutraliser if the drain location or local practice calls for one.
  • Connect power, then set up recirculation and controls according to the chosen approach.
  • Purge air from the water lines, leak-test the gas piping, and commission the unit.

How should recirculation be set up with a Noritz EZ Series?

Recirculation is where tankless installs most often go wrong, because the three common approaches behave very differently. Which one suits you depends on how your house is plumbed and which EZ Series configuration you buy, so check the manual for what your unit supports.

A built-in pump means the circulator sits inside the water heater cabinet and the unit manages it from its own controls. It is the tidiest option when the model you choose has one and your home already has a dedicated return line or you are willing to run one.

An external pump on a dedicated return line means a separate circulator is installed outside the unit, pushing water around a loop that runs from the heater to the far fixtures and back through its own return pipe. This is the most predictable arrangement for longer homes and larger houses, and it is common in newer Lower Mainland builds that were plumbed with a return line.

A crossover or bypass-valve retrofit is used when there is no return line. A valve under the farthest sink connects the hot and cold lines, and the cold line is used as the return path. It avoids opening walls, but it can send lukewarm water into the cold tap for a moment and needs careful control settings so the tankless unit does not short-cycle. In older Burnaby, Vancouver and New Westminster homes without a return line, this is often the realistic option, and we explain its trade-offs before recommending it.

How does commissioning and combustion testing work on a new tankless unit?

Commissioning is the difference between a unit that runs and a unit that runs correctly. With the water heater firing at its highest rate, we measure gas pressure at the unit, and ideally with other gas appliances in the house also running, to confirm the supply holds up under real load. A gas line that looks fine at idle can sag at full fire, which shows up later as fluctuating hot water or ignition faults.

We then run a combustion analysis on the flue gas with a calibrated analyser, checking that carbon monoxide and the other readings sit within the range the manufacturer documents for your model. We confirm the vent and condensate are clearing properly, leak-test every gas joint, and check the delivered water temperature at a couple of fixtures, including the farthest one.

Finally, we set the temperature to a safe, practical level for the household, confirm the recirculation behaves as planned, and walk you through how the unit shows its status. We do not interpret fault displays from memory; the manual lists what each indication means for your model.

What makes a tankless install different in a Metro Vancouver home?

Older housing stock is the biggest factor. Many homes built before the last few decades were plumbed with a gas line sized for a furnace and a tank, and sometimes a fireplace or range was added later on the same small pipe. A tankless unit’s full-fire demand can push that line past what it can carry, so gas-line work is a common part of the scope here.

Venting is the next. Tanks in older homes often vent up a masonry chimney or B-vent shared with a furnace. A condensing EZ Series unit cannot use that path, and the vent has to go out through a sidewall or roof. Tight lot lines on Vancouver Specials and East Van infill, and termination rules around windows, doors and neighbouring property, can decide where the unit ends up.

Strata buildings and townhouses add another layer. Exterior penetrations and termination locations can be governed by strata bylaws, so the owner needs to check with council before we plan a sidewall vent. We never tell you what your strata allows; that is council’s call. Likewise, if your home has a heritage designation, questions about exterior changes go to the municipality.

Water quality works in your favour. Metro Vancouver water is soft, so the heavy limescale common in other regions is not the main concern. Heat-driven mineral deposits and debris still build up in the heat exchanger over time, which is why isolation valves and periodic descaling matter, but the maintenance interval is usually driven by use and the manual’s guidance rather than hard water.

When should I call a licensed technician, and what paperwork should I get?

In British Columbia, gas piping, gas appliance installation, venting and the combustion check are licensed gas-fitter work under a permit. The electrical connection, if a new circuit is needed, is licensed electrical work. A homeowner can choose the location with their installer, clear the work area, keep the condensate drain and vent terminal free of obstructions, and flush filters or read the display as the manual allows. Anything involving gas, venting or wiring is for a licensed technician.

Call us for a site survey if you are replacing a gas tank water heater with an EZ Series unit, if your existing tankless is struggling with winter demand, or if you smell gas, see water around the unit or get repeated ignition faults. We offer same-day service where we can, and we will tell you honestly if a replacement needs a permit, a gas-line upgrade or a meter change that cannot all happen on day one.

Repair versus replacement comes down to the age and condition of the heat exchanger, whether the fault is in an inexpensive sensor or one of the more costly components such as the heat exchanger or control board, and whether the original install had problems with gas supply or venting. We explain what we found and give you a written quote either way.

  • Gas permit number and confirmation the work is open to Technical Safety BC inspection
  • Model and serial number, and the installation and owner’s manuals
  • Recorded gas pressures and combustion analysis readings
  • Vent material, route and termination location noted
  • Recirculation approach and control settings used
  • Descaling and maintenance instructions, with isolation valve locations shown to you
  • Warranty registration guidance from the manufacturer’s documents, which you complete directly with the manufacturer
Gas & carbon-monoxide safety: A Noritz EZ Series tankless water heater burns natural gas and produces carbon monoxide as a combustion by-product. Install working CO alarms on every level of your home and near sleeping areas, and test them regularly. If you smell gas, do not operate switches, phones or appliances inside; leave the house, then call FortisBC and a licensed gas fitter from outside. Never block the vent terminal, combustion-air intake or condensate drain, and never let an unlicensed person alter gas piping or venting. If you lose hot water in cold weather, do not try to warm the house or heat water with a gas oven, stove, barbecue or patio heater indoors. For service, call BC Wide at (604) 473-9690.

Frequently asked questions

Can a Noritz EZ Series really replace my gas tank water heater without major changes?

Often the water piping changes are modest, because the EZ Series is designed with tank replacement in mind. The gas line, the vent route and the condensate drain are the parts that usually need work, especially in older Metro Vancouver homes. A site survey tells you which of those apply before you commit.

Can the EZ Series use my old water heater chimney or vent?

Usually not. A condensing tankless unit needs the vent materials and configuration approved in its installation manual, which are different from the metal vent or chimney a tank used. The old vent opening also has to be dealt with properly so it is not left open or undersized for any appliance still using it.

Do I need a permit and inspection for a tankless installation in BC?

Yes. Installing a gas water heater is regulated gas work that requires a permit taken out by a licensed contractor, and the installation is open to a Technical Safety BC inspection. Ask your installer for the permit number and keep it with your home records.

Will my existing gas line be big enough?

It depends on the unit’s input, the length of the run and what else shares the line. Many older homes need a section of pipe upsized, and sometimes the meter needs to be reviewed with the gas utility. We measure pressure at full fire during commissioning to prove the supply holds up.

How often does a Noritz EZ Series need descaling in Metro Vancouver?

Less often than in hard-water regions, because our water is soft. Heat-driven mineral deposits and debris still build up, so follow the interval in the manual and adjust for how hard the unit works. Isolation valves with service ports make flushing a routine visit rather than a repiping job.

Is BC Wide a Noritz dealer or warranty centre?

No. BC Wide is an independent TSBC-licensed contractor that services and installs the Noritz EZ Series along with other tankless brands. Warranty coverage and registration are set by the manufacturer, so check the documents that come with your unit.

Can you install a new tankless unit the same day my old tank fails?

Same-day where we can, but we never promise a guaranteed window. A straight replacement with an adequate gas line and a workable vent route can move quickly, while gas-line upsizing, a new vent path or a meter change takes longer. We will tell you honestly after the survey.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How long does a hot water tank last?
A standard gas or electric storage tank lasts 8–12 years. A high-quality tank with annual anode rod inspection can reach 15 years. Tankless water heaters typically last 18–22 years when descaled annually in Metro Vancouver's moderately hard water.
Should I switch to a tankless water heater?
Tankless makes sense if you have high demand (large family, multiple bathrooms running at once), want to free up floor space, or value endless hot water. Upfront cost is higher ($3,500–$6,000 installed vs $1,800–$3,200 for a tank) but operating cost is 25–40% lower for gas tankless.
My hot water tank is leaking — is it an emergency?
If the leak is from the tank body itself (not a valve or fitting), the tank is at end of life and needs replacement, usually within 24–48 hours before it floods. Shut off the water supply and gas/electric to the tank and call us.
What brands of water heaters do you install?
We install and service Bradford White, Rheem, AO Smith, John Wood, Giant, GSW for storage tanks; and Navien, Rinnai, Noritz, Bosch and Rheem for tankless units.
Can I install a water heater myself?
In BC, gas water heater installations must be performed by a TSBC-licensed gas fitter and are subject to permit and inspection. Electric tanks require a licensed electrician for the connection. BC Wide handles permits as part of every installation.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote