★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

How to Fix Noritz Tankless Water Heater Error Codes?

Water Heaters

BC Wide Heating & Air Conditioning — water heater services in Greater Vancouver
Home › How to Fix Noritz Tankless Water Heater Error Codes?

How to Fix Noritz Tankless Water Heater Error Codes?

Quick answer

A Noritz tankless water heater error code is the unit’s own diagnosis: it has stopped the burner because it sensed a problem with ignition, flame, combustion air, venting, water temperature or condensate drainage. Write the code down, confirm its meaning against the manual for your unit, and do only owner-safe checks: power, gas valve open, outdoor vent terminals clear, condensate drain visible. Reset once, only if the manual allows it. If the code comes back, call a licensed gas fitter at BC Wide on (604) 473-9690.

If your Noritz tankless water heater is flashing an error code on its remote controller, it is telling you exactly where the problem is before hot water fails completely. This guide explains the most common Noritz codes Greater Vancouver homeowners see, what each one means, and which issues you can safely check yourself versus when to call a licensed technician at BC Wide.

Common Noritz error code symptoms

Noritz tankless units display a two-digit code on the connected remote controller (kitchen or bathroom panel) when the unit stops or detects a fault. The hot water tap often runs cold or lukewarm while the code is showing. Recognizing the code is the fastest way to understand what is happening inside the unit.

  • Code 10 – Combustion air or exhaust restriction. The unit senses it cannot draw enough air or vent properly, so it shuts down for safety.
  • Code 11 – No ignition. The burner is not lighting, which is the single most common code in Greater Vancouver homes.
  • Code 12 – Flame failure. The burner lit but the flame went out or was not sensed during operation.
  • Code 16 – Over-temperature. The unit detected water hotter than its safe limit, often linked to scale buildup.
  • Code 29 – Condensate or heat-exchanger drainage issue.
  • Code 90 / 99 – Combustion abnormality or venting fault, frequently flagged after a blocked or improperly sloped vent.

A code that clears after one restart and never returns may have been a one-time glitch. A code that returns immediately, or every time you draw hot water, points to a real fault that needs proper diagnosis.

What causes Noritz error codes in Greater Vancouver homes

Most Noritz faults trace back to a handful of causes common in our region. Hard water and mineral scale are a leading factor: scale coats the heat exchanger, restricts flow, and triggers over-temperature (16) and flame-related codes. Noritz units are designed to be descaled (flushed) periodically, and skipping this maintenance is the most frequent reason older units start throwing codes.

Gas supply problems cause many ignition (11) and flame-failure (12) codes. A partially closed gas valve, low gas pressure, or air in the line after service can all prevent a clean light-off. Venting and air-intake blockages drive codes 10, 90, and 99 — debris, ice at the termination in cold snaps, a disconnected vent section, or improper slope can all restrict combustion air and exhaust. Condensate drainage faults (code 29) occur when the drain line is clogged or kinked.

Electrical and sensor issues, such as a failing flame sensor or a tripped condition after a power event, can also raise codes. Because Noritz units burn natural gas and route exhaust through sealed venting, the gas, combustion, venting, and sealed internal components must only be inspected and serviced by a licensed technician — never attempt to open the gas valve assembly, vent, or burner chamber yourself.

When to call BC Wide

You can safely do a few first checks. Confirm the gas is on at the meter and the unit’s service valve, make sure other gas appliances are working, and verify the unit has power. You can also check that the outdoor or sidewall vent termination is clear of snow, leaves, or nests. After clearing an obvious obstruction, cycle the unit off and on at the controller to see if the code clears.

If the code returns, call a licensed technician. You should always call BC Wide for any code tied to gas, combustion, venting, refrigerant, or sealed internal parts — including ignition (11), flame failure (12), air/exhaust faults (10, 90, 99), over-temperature (16), and condensate faults (29) that do not clear. These require gas-pressure testing, combustion analysis, descaling, or component replacement that must be performed safely and to TSBC code.

BC Wide has served Greater Vancouver since 1999 with in-house technicians and TSBC licensing (LGA90068). We diagnose the actual cause behind the code, descale and service Noritz tankless units, and confirm the unit is venting and burning safely before we leave. Call us at 604-473-9690 to book a Noritz diagnostic or maintenance flush.

See our water heater service hub and tankless guide.

BC Wide Heating & Air Conditioning has served Greater Vancouver since 1999 with in-house, Technical Safety BC–licensed (gas contractor LGA90068) technicians — never subcontractors. Honest, up-front pricing before any work begins. Rated 4.7★ across 180+ verified Google reviews.

Frequently asked questions

What does error code 11 mean on my Noritz tankless water heater?

Code 11 means the unit is failing to ignite — the burner is not lighting. The most common causes are a closed or low-pressure gas supply, air in the gas line after service, or a venting/air-intake restriction. Check that the gas is fully on and other gas appliances work, then cycle the unit. If code 11 returns, call a licensed BC Wide technician at 604-473-9690, since gas and combustion work must be done professionally.

Can I reset my Noritz water heater myself when it shows a code?

Yes — turning the unit off and on at the remote controller is a safe reset, and a one-time code may clear and not return. You can also confirm the gas is on and clear any visible blockage at the vent termination. However, do not open the gas valve, burner chamber, or venting yourself. If the code comes back after a reset, the fault is real and needs a licensed technician to diagnose safely.

How often should a Noritz tankless water heater be descaled in Greater Vancouver?

Most Noritz units benefit from descaling (a flush) about once a year, and harder water or heavy use may call for more frequent service. Skipping descaling lets scale build up on the heat exchanger, which restricts flow and triggers over-temperature (code 16) and flame-related faults. BC Wide can perform a maintenance flush and full inspection — call 604-473-9690 to schedule.

Book water heater service in Greater Vancouver

Call BC Wide Heating & Air Conditioning at 604-473-9690 or email info@bcwide.ca. Technical Safety BC–licensed (LGA90068), serving Metro Vancouver since 1999.

Noritz Tankless Water Heater Error Code Guide: what we check first

When we arrive at a Noritz unit showing a code, we do not start by replacing parts. A code tells us which safety circuit stopped the burner, not which part failed. Several different faults can trigger the same code, so we work through the causes in the order we actually find them in Greater Vancouver homes, from the most common to the least common. The list below is that order, with the checks an owner can safely make and the point where it becomes work for a licensed gas fitter.

Every meaning on this page should be confirmed against the manual for your unit, because display wording and code lists can differ between generations of the same brand.

  • 1. Gas not reaching the burner properly. A supply valve left partly closed after other work, a gas line that is too small for the unit when the furnace or range is also running, or a supply problem at the meter. Owner check: the handle on the gas valve beside the heater should sit in line with the pipe, and your other gas appliances should be working. Anything beyond that valve is licensed gas work.
  • 2. A restricted intake or exhaust terminal. Leaves, wind-blown debris, a wasp or bird nest, or snow drifted against a low wall terminal. Owner check: look at the terminal from outside and clear loose debris by hand if you can reach it safely from the ground. Disconnected, sagging or damaged vent pipe is a licensed call.
  • 3. A blocked, kinked or frozen condensate drain. Condensing tankless units make acidic condensate that has to drain away freely, and a backed-up drain will shut the unit down. Owner check: confirm the drain line is connected, not kinked and not frozen where it runs outside or through a cold space. Opening the unit to clear the trap or service the neutralizer is technician work.
  • 4. Dirty or worn ignition and flame-sensing parts. Over years of cycling, the igniter and flame sensor collect deposits and the burner stops lighting or proving flame reliably. There is no owner check here; this needs the cover off and a meter on the circuit.
  • 5. Restricted water flow or deposits in the heat exchanger. A clogged inlet filter screen or heat-driven mineral deposits can let water overheat inside the exchanger. In our soft water this builds slowly, but it is real on units that have never been serviced. Flushing and cleaning the inlet screen belong in a scheduled service visit.
  • 6. Electrical supply or control faults. A tripped breaker, an unplugged cord, a surge after a storm, or a failing control board or sensor. Owner check: confirm the unit has power and the breaker has not tripped. If the breaker trips again, leave it off and call.
What you noticeLikely causeOwner-safe checkWhen it becomes a licensed call
Tap runs cold and the remote shows a code within secondsGas not reaching the burner, or ignition parts not lightingGas valve handle in line with the pipe; other gas appliances workingAny gas smell, a closed meter, or the code returning after one reset
Code appears after a storm or the first snowIntake or exhaust terminal blocked by debris or snowClear loose debris or snow at the terminal from the groundVent pipe damaged, disconnected, sagging or iced inside
Water under the unit or a gurgling soundCondensate drain blocked, kinked or frozenLook at the drain line for kinks, a loose end or iceWater coming from inside the cabinet or the code persisting
Hot water goes very hot, then the unit stopsRestricted flow or deposits in the heat exchangerNote when it happens and how many taps were openFlushing, inlet screen cleaning and sensor testing
Code only when two showers or the dishwasher run togetherGas line struggling under high demandNote which appliances were running at the timeGas pressure testing and line sizing review
Remote is blank or the unit is completely silentNo power, tripped breaker, or a control faultCheck the plug and breaker onceBreaker trips again, burning smell, or a blank display with power present

What does a Noritz error code mean for you: hot water, heat and safety?

In plain terms, a code means the unit has decided it is not safe or not able to keep firing, so it has stopped heating water. A tankless heater has no stored hot water to fall back on, so when the burner stops, the tap goes cold almost at once. That is the design working as intended: a shutdown with a code is far better than a burner that keeps running with poor combustion or a blocked vent.

If your Noritz also feeds a hydronic air handler or in-floor loop, a code can mean no space heat as well as no hot water. Tell us that when you call, because it changes how quickly the job needs to happen in cold weather.

Here is how homeowners usually describe what they are seeing when they call us about a Noritz code:

  • The shower started hot, then went cold halfway through, and there is a number on the remote.
  • The unit clicks several times, then goes quiet and the code comes up.
  • It works for one tap but shuts off when someone else turns on a shower.
  • The code showed up the morning after a windstorm or the first snowfall.
  • There is a puddle or a drip under the unit and the hot water has stopped.
  • It resets and works for a day, then the same code comes back.
  • There is a whistling, rumbling or rattling sound from the vent before it stops.

Can I reset a Noritz tankless water heater myself, and what should I leave alone?

You can make a small number of safe checks, and you may reset the unit once if the owner manual for your model describes a reset. If the code returns after that single reset, stop. Repeated resetting relights a burner that has already told you something is wrong, and on a combustion or venting fault that can mean running the appliance while exhaust is not leaving the house properly.

Owner-safe checks:

  • Confirm the unit has power: the plug is in, the breaker is on, and the remote display is lit.
  • Confirm the gas supply valve beside the heater is open, with the handle running in line with the pipe.
  • Confirm your other gas appliances, such as the furnace or range, are working normally.
  • Look at the outdoor intake and exhaust terminals and clear leaves, snow or a visible nest by hand if you can reach safely from the ground.
  • Look at the condensate drain line where you can see it: connected, not kinked, not frozen.
  • Write down the code, the time it appeared, and what was running in the house, then reset once only if your manual allows it.
Leave this to a licensed technicianWhy
Removing the front cover or opening any panelLive electrical parts and gas components sit behind it
Jumpering, bypassing or disconnecting any sensor or switchThose circuits are the safeties that prevent unsafe combustion
Loosening, adjusting or replacing gas fittings or the gas valveGas work in BC is restricted to licensed gas fitters
Cutting, rejoining or re-sloping vent pipeVent materials, slope and clearances must meet code and the manual
Repeatedly resetting the unit to get hot water backIt keeps relighting a burner that has already flagged a fault

How our Noritz tankless repair visit works, step by step

Diagnostic service calls are $189.00. That covers the technician’s visit and a proper diagnosis with test instruments, not a guess based on the code alone. We offer same-day visits where we can, depending on the day’s bookings and where you are, and we will tell you honestly on the phone if that is not possible. We do not promise an arrival window we cannot keep.

This is what happens once our licensed gas fitter is at the unit:

  • 1. We read the code and its history from the remote, ask what you noticed and what was running, and check whether it repeats on demand.
  • 2. We check the outside first: intake and exhaust terminals, vent pipe support and joints, clearances, and the condensate drain route.
  • 3. We measure gas pressure at the unit with a manometer, both with the heater alone and with your other gas appliances firing, to see whether supply holds under load.
  • 4. We test the electrical side with a meter: supply voltage, the igniter circuit, the flame-sensing signal and the temperature sensors, against the values the manual specifies.
  • 5. We inspect the burner, the condensate trap and neutralizer, the inlet filter screen and, where needed, flow through the heat exchanger.
  • 6. We explain the cause in plain words. The parts most often involved in general terms are igniters, flame sensors, temperature sensors, fans, condensate components and, less often, a control board, which is one of the more expensive parts on any tankless unit.
  • 7. You get a written quote before we do any work beyond diagnosis. Nothing is replaced until you approve it.
  • 8. After a repair, we fire the unit through its full range, confirm venting and combustion, test the safeties, check for gas leaks at every joint we touched, and run hot water at more than one fixture.

Should I repair or replace an older Noritz tankless water heater?

A single sensor or igniter fault on a unit that has been looked after is usually worth repairing. The decision changes when the unit is older, has had several different faults in a short period, has a leaking or heavily fouled heat exchanger, or needs a control board on top of other work. At that point we will show you the repair quote and the replacement option side by side in writing and let you decide.

What we weigh on site: the age shown on the rating plate, the service history, whether parts for that generation are still readily available, the condition of the heat exchanger, and whether the existing gas line and venting are adequate. In older Greater Vancouver housing, gas-line size and the venting route are often the real deciders, not the heater itself. A unit that has always struggled when two showers run may have been starved of gas from day one.

If replacement makes sense, the in-home estimate for replacing or installing equipment is free. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation.

We are an independent contractor, so we are not tied to one manufacturer. Tankless and combi brands we service include Noritz, Rinnai, Navien, Rheem, Bradford White, Takagi, Bosch and A. O. Smith. We describe each one neutrally and help you choose based on your gas supply, venting route, hot water demand and whether you want recirculation. Any capacity or efficiency figure is manufacturer-published, so verify it for the exact model before you decide.

Noritz tankless repair near me: Greater Vancouver coverage and why licensing matters

We service Noritz tankless water heaters across Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the rest of the Tri-Cities, the North Shore, New Westminster, Delta and Langley. Housing stock varies a lot across that area. Older detached homes in parts of Vancouver, Burnaby and New Westminster often had tankless units added long after the house was built, so gas lines and vent routes were sometimes fitted to what was already there. Townhouses and strata buildings, common in Burnaby, Coquitlam, Richmond and Surrey, can add strata rules, shared walls and limited spots for vent terminals. Newer homes in Langley, Surrey and Delta more often have units planned in from the start, but even those need routine service.

Our wet coastal climate shapes the faults we see. Wind-driven rain, fallen leaves and the occasional heavy snowfall all reach low wall terminals, and condensate lines that run outside can freeze during a cold snap. Our incoming water is soft, so heat exchanger deposits build slowly here, but units that have never been flushed or had the inlet screen cleaned still develop flow and over-temperature problems.

BC Wide Home Services Ltd is a TSBC-licensed independent contractor, licence LGA0090068, with Class B gas licence CGA0028029, serving Metro Vancouver since 1999. Our gas fitters are licensed, we pull permits and arrange inspections where the work requires them, and you receive a written quote before any work beyond diagnosis. We are not a Noritz authorized dealer or warranty centre; if your unit may still be under manufacturer warranty, check the warranty terms with the manufacturer before booking any repair.

Gas and carbon monoxide safety: if you smell gas or your carbon monoxide alarm sounds, do not reset the heater or operate switches. Leave the home, then call FortisBC or 911 from outside. Every home with a gas tankless heater should have working CO alarms near sleeping areas. Call BC Wide at (604) 473-9690 once it is safe.

More questions homeowners ask

What does a Noritz tankless water heater error code mean?

It means the unit has stopped the burner because a safety or operating check failed, such as ignition, flame, combustion air, venting, temperature or condensate drainage. The code points to the circuit that tripped, not always to the failed part. Confirm the meaning against the manual for your unit, and have a licensed technician diagnose a code that returns.

Can I reset my Noritz tankless water heater after an error code?

Yes, once, if your owner manual describes a reset, and only after checking power, the gas valve, the outdoor vent terminals and the condensate drain. If the code returns, stop resetting. Repeated resets relight a burner that has already flagged a fault, which can be unsafe on a venting or combustion problem.

Is it safe to run a Noritz tankless water heater that keeps showing an error code?

No. A code that keeps coming back means the cause is still there, and some of those causes involve combustion or venting. Leave the unit off and book a licensed gas fitter. If you smell gas or a CO alarm sounds, leave the home and call FortisBC or 911 from outside.

Why does my Noritz tankless show an error only when two showers are running?

The most common reason is that gas supply drops when demand peaks, especially if the gas line was sized before the tankless unit went in or the furnace is firing at the same time. Restricted flow or a dirty inlet screen can also play a part. A technician confirms it by measuring gas pressure at the unit while other appliances run.

Do you repair Noritz tankless water heaters near me in Greater Vancouver?

Yes. BC Wide services Noritz tankless water heaters in Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the Tri-Cities, the North Shore, New Westminster, Delta and Langley. Diagnosis is done by a licensed gas fitter, with same-day visits where we can. Call (604) 473-9690 to book.

Is BC Wide a Noritz authorized dealer or warranty centre?

No. BC Wide is an independent TSBC-licensed contractor, licence LGA0090068 and Class B gas CGA0028029, and Noritz is one of the brands we service. If your unit may still be under manufacturer warranty, check the warranty terms with the manufacturer first. For out-of-warranty repairs, we give you a written quote before any work beyond diagnosis.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How long does a hot water tank last?
A standard gas or electric storage tank lasts 8–12 years. A high-quality tank with annual anode rod inspection can reach 15 years. Tankless water heaters typically last 18–22 years when descaled annually in Metro Vancouver's moderately hard water.
Should I switch to a tankless water heater?
Tankless makes sense if you have high demand (large family, multiple bathrooms running at once), want to free up floor space, or value endless hot water. Upfront cost is higher ($3,500–$6,000 installed vs $1,800–$3,200 for a tank) but operating cost is 25–40% lower for gas tankless.
My hot water tank is leaking — is it an emergency?
If the leak is from the tank body itself (not a valve or fitting), the tank is at end of life and needs replacement, usually within 24–48 hours before it floods. Shut off the water supply and gas/electric to the tank and call us.
What brands of water heaters do you install?
We install and service Bradford White, Rheem, AO Smith, John Wood, Giant, GSW for storage tanks; and Navien, Rinnai, Noritz, Bosch and Rheem for tankless units.
Can I install a water heater myself?
In BC, gas water heater installations must be performed by a TSBC-licensed gas fitter and are subject to permit and inspection. Electric tanks require a licensed electrician for the connection. BC Wide handles permits as part of every installation.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote