★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

NTI Boiler Code Alert 248 — Outdoor sensor invalid (Tft/FTV) | BC Wide

Boilers, Error Codes, Hvac

NTI Boiler Code Alert 248 — Outdoor sensor invalid (Tft/FTV) | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › NTI Boiler Code Alert 248 — Outdoor sensor invalid (Tft/FTV) | BC Wide

NTI Boiler Code Alert 248 — Outdoor sensor invalid (Tft/FTV) | BC Wide

Quick answer

NTI boiler error code Alert 248 means the boiler control could not get a valid outdoor temperature reading for central heating. With outdoor reset enabled, that points to an outdoor sensor that is missing, miswired or faulty, or one covered in ice or snow. Confirm the meaning against the manual for your unit. It is listed as a status alert, not a lockout, but heating may stop tracking the weather properly. Clear snow from the sensor if you can reach it safely, then call (604) 473-9690 for a licensed diagnosis.

If your NTI boiler is showing Alert 248 (Outdoor sensor invalid (Tft/FTV)), here’s exactly what it means and what to do. This guide is part of our full NTI boiler error code list.

Severity: Status / informational.

What Alert 248 means on a NTI boiler

Alert 248: the CH outdoor temperature was invalid – the Trinity Tft ships with outdoor reset enabled, so the outdoor sensor is missing, miswired, or faulty.

Common causes

  • Outdoor sensor not connected (with outdoor reset enabled)
  • Outdoor sensor wiring fault
  • Faulty sensor, or sensor covered in ice/snow

What you can safely check first

  1. Check the outdoor sensor is clear of ice and snow if you can see it safely
  2. Wiring and reset-setting changes should be done by a technician

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a NTI boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

NTI boiler repair across Greater Vancouver

If a NTI boiler showing Alert 248 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related NTI boiler codes

Frequently asked questions

Is Alert 248 on a NTI boiler serious?

It’s typically a status/informational code rather than a breakdown, but confirm against the symptoms. BC Wide repairs NTI boilers 7 days a week across Greater Vancouver.

How do I reset a NTI boiler after Alert 248?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

NTI boiler error code Alert 248: what it means for your heat and hot water

In plain terms, Alert 248 tells you the boiler has lost its view of the weather. An NTI boiler set up for outdoor reset uses a small sensor on an exterior wall to decide how hot to make the water it sends to your radiators, in-floor tubing or fan coils. On a mild, wet day it should run cooler, longer and quieter. On a cold snap it should push hotter water. When the control reads that sensor as invalid, it can no longer make that adjustment, so it raises Alert 248. Confirm the exact meaning, and how your model responds, against the manual for your unit.

Because this alert is listed as status or informational rather than a hard lockout, many homeowners find the boiler still fires. What changes is how well it heats. Depending on how the control is programmed, the boiler may fall back to a default supply temperature, may not heat the house enough on colder days, or may burn more gas than it needs to by running hotter on mild days. We do not guess which of those your boiler is doing. The manual and a technician reading the control settings will tell you.

Domestic hot water is a separate question. If your NTI boiler also heats an indirect tank, domestic hot water usually runs on its own setpoint rather than on outdoor reset, so hot water is often unaffected. If you have lost hot water as well as seeing Alert 248, something else may also be wrong. Tell us when you call so the technician comes prepared.

Here is how owners usually describe the problem when they phone about this code:

  • The boiler display shows Alert 248, and the house is still roughly warm but less comfortable than usual.
  • Some rooms or in-floor zones are slow to warm up in the morning or after a cold night.
  • The house overheats on mild afternoons and the boiler seems to run hotter than it used to.
  • The alert appeared after a snowfall, a cold clear night or a hard frost.
  • The alert appeared after painting, new siding, a deck build, landscaping or a new fence on that side of the house.
  • The alert showed up after a power cut, a control replacement or someone changing the boiler settings.
  • Nobody in the house knew there was a small sensor cap on an outside wall until now.

NTI boiler error code Alert 248: what we check first, most likely cause first

When we arrive for an Alert 248 call, we work through the causes in the order we usually find them in Greater Vancouver homes. Each cause below lists what a homeowner can safely look at and the point where it becomes a job for a licensed technician.

1. Damaged or disconnected sensor wiring. The cable from the outdoor sensor to the boiler is low-voltage wire. It is often stapled along a joist, passed through a rim board and run out through an exterior wall. Renovations, rodents, a new dryer vent, an electrician pulling new cable or a crew replacing siding are the usual culprits. Owner check: look along any cable you can see outside for cuts, chew marks or a pulled-out end. Licensed call: any splice or reconnection, and anything inside the boiler cabinet or at the wiring terminals.

2. Sensor buried in snow, ice or debris, or painted over. Owner check: from the ground or another stable spot, clear away snow, ice, leaves or a wasp nest by hand, wearing gloves. Do not chip at ice with a tool or pry the cover off. If the alert clears some time after the sensor is uncovered, make a note of it and tell us. It is still worth having looked at so the same thing does not happen in the next cold spell.

3. A failed outdoor sensor. These sensors sit outside through years of coastal rain and freeze-thaw cycles, and water getting in followed by corrosion is a common way for them to fail here. Owner check: look at it, nothing more. Licensed call: a technician measures the sensor with a meter and checks the reading against the manufacturer’s temperature-resistance data before replacing anything.

4. No sensor installed, or the sensor was removed or moved, while outdoor reset is still enabled. Some boilers ship with outdoor reset turned on. If the sensor was never fitted at installation, was removed during a renovation, or the control was replaced, the boiler can report the sensor as invalid. Licensed call: either fit and wire a sensor properly, which is the better result for comfort and gas use, or have a technician review the installer settings. Owners should not change installer-level settings.

5. A control or connection fault at the boiler. This is less common. A loose terminal, a corroded connector or a fault in the control itself can make a working sensor read as invalid. This is a licensed call only.

Before you call, run through the basic checks that apply to any boiler alert. Make sure the boiler’s power switch is on and the breaker has not tripped. Make sure the gas valve to the boiler is open, the thermostat is actually calling for heat, the outside intake and exhaust terminal is clear of snow, leaves and nests, and the condensate drain you can see is not kinked, frozen or overflowing. If the manual for your unit allows a reset, do it once only. If Alert 248 comes straight back, stop resetting and book a visit. Do not open panels, jumper or bypass anything, or unplug the sensor to see what happens.

Alert 248 is a sensor alert, not a gas fault, but your boiler still burns gas. If you smell gas or a carbon monoxide alarm goes off, skip every check on this page. Leave the house, leave the door open behind you, and call FortisBC or 911 from outside. Every home with a gas boiler should have working CO alarms near the bedrooms and on each level.

Likely causeWhat you may safely checkWhen it becomes a licensed call
Damaged or disconnected sensor wireLook along any visible outdoor cable for cuts, chew marks or a pulled-out endAny splice or reconnection, and anything at the boiler terminals
Sensor covered by snow, ice, leaves or paintClear snow, leaves or nests by hand from a safe, stable spotIf the alert does not clear, or the sensor housing is cracked or holding water
Failed outdoor sensorA visual look from outside onlyMeter testing against manufacturer data, and replacing the sensor
Sensor missing or moved while outdoor reset is still onCheck whether there is a sensor on an outside wall at allFitting a sensor or reviewing installer settings
Loose terminal or control faultNone; do not open the boiler cabinetAlways a technician diagnosis

How our NTI boiler Alert 248 repair visit works

Diagnostic service calls are $189.00. That pays for a licensed technician to come to your home, find the actual cause and explain it to you before any further work. The visit goes step by step like this:

Sensor placement matters as much as the sensor itself. We mount it on a shaded wall, usually north-facing, out of direct sun and away from dryer vents, exhaust terminals and windows that would throw off its reading. It also goes high enough to stay clear of snow and sprinkler spray. A badly placed sensor can make a boiler heat poorly even when no alert is showing, so if yours is in a poor spot we will tell you and give you the option to move it.

  • Booking: you call (604) 473-9690 and tell us the code, the boiler brand, roughly how old it is, and anything that has changed outside the house lately. We book the earliest slot we have and offer same-day service where we can, but we will not promise an arrival window we cannot keep.
  • Safety first: the technician checks for gas odour and combustion concerns, confirms the venting terminals are clear, and makes sure the boiler is safe to work on.
  • Read the control: we read the alert history and the current outdoor reset and installer settings. That tells us whether outdoor reset is meant to be on and what the boiler is doing in the meantime.
  • Trace and test: we find the sensor, follow its wire back to the boiler, and test both the sensor and the wiring with a meter. We compare the readings to the manufacturer’s published data instead of guessing.
  • Explain and quote: we show you what failed. If the fix goes beyond the diagnosis, you get a written quote first, and nothing beyond the diagnosis is done until you approve it.
  • Repair: the parts usually involved are the outdoor sensor itself, a run of low-voltage cable, a better-protected mounting spot, or a terminal connection. A control fault is rarer and is one of the more expensive boiler repairs, so we confirm it carefully before recommending it.
  • Test the safeties and confirm: after the repair we check that the control reads a sensible outdoor temperature, the alert has cleared, and the boiler fires and modulates normally. We also check the safeties and take a combustion reading at the flue.
  • Paperwork: you get an invoice stating what we found, what we replaced and where the sensor is now mounted.

Repair or replace: is an older NTI boiler with Alert 248 worth fixing?

Alert 248 on its own is almost never a reason to replace a boiler. In most cases the fault is outside the boiler, in a sensor or a run of wire, and fixing it brings outdoor reset back. We tell owners that plainly, even when the boiler is older.

Replacement only comes up when Alert 248 is one problem among several. Things that change the picture: corrosion or heavy sludge build-up in the heat exchanger, repeated lockouts that have nothing to do with this code, a failed control that is hard to get parts for on your model, leaks at the boiler, or venting that no longer meets current requirements. Metro Vancouver water is soft, so the problems we find inside older hydronic systems are sludge, magnetite and corrosion, not limescale. Those are what shorten a heat exchanger’s life.

If you are weighing it up, ask for both options in writing: the repair quote and a replacement estimate. In-home estimates for replacing or installing equipment are free. If you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation. A replacement also needs a gas permit and an inspection. We pull the permit and arrange the inspection as part of doing the job correctly; it is not an optional extra.

Whichever way you go, here is what you should see in writing:

  • The cause we found and how we confirmed it
  • The repair scope, with parts and labour quoted before work starts
  • Where the outdoor sensor is mounted, and how its wire is run and protected
  • For a replacement: the equipment, the venting plan, the gas permit and inspection, and what happens to the old boiler

NTI boiler Alert 248 service near me: Greater Vancouver coverage

From our base in Burnaby we service NTI boilers across Greater Vancouver: Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities including Port Coquitlam and Port Moody, the North Shore, New Westminster, Delta and Langley.

The type of house affects how an Alert 248 job goes. In older Vancouver, Burnaby and New Westminster houses that have been upgraded to a high-efficiency boiler, the sensor wire often runs through finished basements or along the outside siding, and later renovations tend to disturb it. On the North Shore, higher and shadier lots tend to get more snow and longer frosts, so a buried or iced-over sensor is more likely there in a cold spell. In Richmond and Delta, wind-driven rain on open, flat lots is hard on a sensor mounted where it takes the weather. In Surrey, Langley and Coquitlam, newer townhomes and houses with in-floor heating often have the boiler in a garage or mechanical room, and the sensor sits on a nearby wall where a later fence or deck can bury it. These are tendencies, not rules. Your house is assessed on its own.

In strata buildings and townhome complexes, the outside wall belongs to the strata. If the sensor or its wire has to move, or a new hole has to go through the building envelope, we tell you before we do it so you can check with your strata council.

Besides NTI, we service hydronic boilers from IBC, Navien, Viessmann, Lochinvar, Weil-McLain, Buderus and Bosch. We service these brands as an independent contractor; we are not a certified dealer or warranty centre for any of them. If your boiler is still under manufacturer warranty, read the warranty terms first, and we will tell you if we think a claim should go through the original installer or the manufacturer.

Our mild, wet climate is the reason outdoor reset is worth having. Most of the heating season falls in the shoulder range, where a condensing boiler works best at lower water temperatures. Without a working outdoor sensor, you lose much of that advantage. That is why we treat Alert 248 as worth fixing even when the house still feels warm.

Who should fix an NTI boiler error code: what a licensed contractor does differently

BC Wide Home Services Ltd is an independent gas contractor licensed by Technical Safety BC (gas contractor licence LGA0090068, Class B gas licence CGA0028029), serving Metro Vancouver since 1999. Our technicians are licensed gas fitters on our own staff.

In BC, gas work and most electrical work are restricted to licensed trades. As a homeowner you may look things over, clear snow and leaves, check switches and valves, and reset once if your manual allows it. Anything inside the boiler cabinet, any change to installer settings, and any wiring repair is work for a licensed technician.

  • Licensed gas fitters do every boiler diagnosis and repair
  • Gas permits pulled and inspections arranged wherever the work needs them
  • A written quote before any work beyond the diagnosis
  • A plain explanation of what failed and how we tested it, using meters rather than guesswork
  • Honest repair-or-replace advice, including telling you when a repair is the right call
  • Independent: we are not an authorised dealer or warranty centre for any brand

More questions homeowners ask

What does NTI boiler error code Alert 248 mean?

It means the boiler could not get a valid outdoor temperature reading for central heating while outdoor reset is enabled. That usually means the outdoor sensor is missing, miswired or faulty, or covered in ice or snow. It is listed as a status alert, not a lockout. Confirm the meaning against the manual for your unit.

Can I reset NTI boiler Alert 248 myself?

Only if your owner manual allows a reset, and only once. Clear any snow, ice or debris off the outdoor sensor first. If the alert comes back, stop resetting and call a licensed technician, because repeated resets hide the cause instead of fixing it.

Is it safe to run my NTI boiler with Alert 248 showing?

Usually the boiler can keep running, because this alert is about an outdoor temperature reading, not combustion. Heat may be less even or less efficient until the sensor is fixed. If you smell gas or a CO alarm sounds, leave the house and call FortisBC or 911 from outside.

Where is the outdoor sensor on an NTI boiler system?

It is a small sensor on an outside wall, usually a shaded north-facing one, wired back to the boiler with low-voltage cable. If you cannot find one at all, it may never have been installed, or it was removed while outdoor reset stayed on. We locate and trace it during the visit.

Do you offer same-day NTI boiler repair near me in Greater Vancouver?

We offer same-day service where we can, depending on the day’s bookings and where you are. We will not promise an arrival window we cannot keep. Call (604) 473-9690 with the code and your boiler details, and we will give you the earliest real slot.

Should I replace my NTI boiler because of Alert 248?

Rarely. This alert usually traces back to a sensor or its wiring, and fixing that brings proper outdoor reset back. Replacement only makes sense if the boiler has other serious problems, such as heat exchanger corrosion or a failed control that is hard to get parts for. The in-home estimate for a replacement is free if you want to compare both options.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote