- Ask for a room-by-room heat loss calculation, not a rule-of-thumb size based on floor area or the size of your old furnace.
- Ask what electrical work is included: panel capacity check, dedicated circuit, disconnect, and whether a permit and possible service upgrade are in the quote or extra.
- Ask what the backup heat strategy is below the balance point, and whether the system is fully ducted, ductless, or a dual-fuel hybrid with your existing furnace.
- Ask where the outdoor unit will sit, how it will be raised for drainage and defrost meltwater, and how it will be isolated from walls to control vibration in a townhouse or duplex.
- Ask for the permit, licence and inspection plan in writing, plus the exact model numbers, warranty registration requirement and commissioning report.
- Get every answer in a written, itemised quote. Verbal promises about electrical scope and cold-weather output are where most heat pump disputes start.
Before you accept a heat pump quote, ask five things: how the contractor sized the system (a room-by-room heat loss calculation, not a guess from square footage), exactly what electrical work is included and whether a panel or service upgrade might be needed, what happens on the coldest nights and what provides backup heat, where and how the outdoor unit will be mounted and drained, and who pulls the permits and books the inspection. A quote that answers all five in writing, with model numbers and a clear scope line for electrical, is a quote you can compare fairly. A quote that is one line and a total is not a quote at all — it is a number, and the missing details are where the surprises live.
How did you size this heat pump, and can I see the calculation?
This is the single most important question, and the answer separates a designed system from a guessed one. Proper sizing comes from a heat loss and heat gain calculation that works room by room: wall and ceiling insulation values, window area and glazing type, air leakage, orientation, ceiling heights, and the outdoor design temperature used for your part of Metro Vancouver. The output tells the contractor how much heat the house actually loses on a cold day, which then drives equipment selection.
Beware two shortcuts. The first is sizing by floor area alone. The second, and more common, is matching the capacity of the furnace being replaced — furnaces in older Lower Mainland homes were routinely oversized, and copying that number forward bakes the error into the new system. A heat pump that is too large short-cycles: it satisfies the thermostat quickly, shuts down, restarts, and never settles into the steady low-speed operation where it is most efficient and most comfortable. Short-cycling also means less dehumidification in summer and more wear on the compressor.
Undersizing is the opposite failure and is less common but harder to live with: the system runs continuously in cold weather, leans hard on backup heat, and the house drifts below setpoint on the worst nights. Ask to see the calculation as a document. A contractor who has done one will hand it over.
- Ask: what outdoor design temperature did you use, and what indoor temperature did you design to?
- Ask: is this a room-by-room calculation or a whole-house estimate?
- Ask: what assumptions did you make about insulation and windows, and did you verify them on site or assume them?
- Ask: how does the selected capacity compare to my calculated heat loss at design conditions?
- Ask: how will this size affect summer humidity and cycling behaviour?
What electrical work is included, and could I need a service upgrade?
A heat pump is a substantial electrical load, and in older housing the electrical side is where quotes diverge most. The outdoor unit needs its own properly sized circuit, an approved disconnect within sight of the unit, and correct wire sizing for the run length. If the system uses electric backup heat in an air handler, that is a second and often larger load. Add an existing electric range, an electric water heater and a vehicle charger and a panel that has served the house fine for decades can run out of capacity.
Ask the contractor to state, in the quote, whether an electrical load calculation was performed on your existing service, what the result was in general terms, and whether the quoted price assumes the existing panel is adequate. This is the number one source of unwelcome change orders. A quote that says electrical by others, or is silent on the topic, is not comparable to one that includes a dedicated circuit, disconnect, permit and inspection.
Electrical work of this kind is restricted in British Columbia. You may choose your equipment, clear access to the panel, and decide where you would prefer the disconnect. You may not run the circuit, land conductors in the panel, or change a breaker. That work must be done by a licensed electrical contractor under permit, and the installation must pass inspection. Turning off a breaker is homeowner territory; anything behind the panel cover is not.
- Ask: was a load calculation done on my existing service, and does the quote assume it passes?
- Ask: is the dedicated circuit, disconnect, wiring, electrical permit and inspection included in this price, or billed separately?
- Ask: if a panel change or service upgrade turns out to be required, how is that priced and who coordinates it with the utility?
- Ask: does the air handler or backup heat need its own circuit as well?
- Ask: who is the licensed electrical contractor doing the work, and will I receive the permit number?
What happens on the coldest nights, and what is the backup heat plan?
Every air source heat pump produces less heat as the outdoor temperature falls, because there is less heat energy in the outdoor air to move indoors. The temperature at which the heat pump’s output exactly matches the home’s heat loss is called the balance point. Above it, the heat pump alone keeps the house comfortable. Below it, something has to make up the difference. Ask the contractor to tell you, plainly, where the balance point of the proposed system lands for your house and what covers the shortfall below it.
There are three common answers in Metro Vancouver. A fully electric system pairs the heat pump with an air handler containing electric resistance elements that stage on as needed. A dual-fuel or hybrid system keeps your existing gas furnace as the backup, with a control strategy that hands off to the furnace below a switchover temperature. A ductless system in a home with existing baseboards may simply let the baseboards cover the extremes in the rooms that need it.
Also ask about defrost. In our wet coastal winters the outdoor coil accumulates frost, and the unit periodically reverses to melt it off. Defrost is normal: steam off the outdoor unit, a brief pause in heating, and a puddle of meltwater under the unit are expected behaviour, not a fault. What matters is that the contractor has planned drainage so that meltwater does not pool and refreeze on a walkway.
Push for specifics on controls. In a hybrid system, who sets the switchover temperature, can it be adjusted later, and is the thermostat capable of managing both stages properly? A mismatched thermostat is a frequent cause of a hybrid system that either never uses the heat pump or never lets the furnace help.
What should an itemised heat pump quote actually contain?
Use this as a checklist when you compare two or three quotes side by side. Each row is a line item you should be able to point to on the page. If a line is missing, ask for it in writing before you decide.
| Quote item | What to look for | Why it matters |
|---|---|---|
| Heat loss calculation | A room-by-room document with stated design conditions | Proves the size was engineered rather than guessed |
| Exact equipment models | Full outdoor unit, indoor unit and coil model numbers | Lets you verify matched components and registered warranty |
| System type | Ducted, ductless, or hybrid with existing furnace | Determines ductwork scope and backup heat behaviour |
| Electrical scope | Circuit, disconnect, permit, inspection, panel assessment | The most common source of change orders |
| Outdoor unit location | Named spot, pad or bracket, height off grade, clearances | Affects drainage, noise, service access and neighbour relations |
| Condensate handling | Indoor drain routing and outdoor meltwater drainage | Prevents water damage indoors and ice on walkways |
| Ductwork changes | Any resizing, sealing, return air additions or new registers | Heat pumps move more air at lower temperature than a furnace |
| Thermostat and controls | Model, compatibility with staging and backup heat | Wrong control undermines an otherwise good installation |
| Permits and inspection | Who applies, which permits, expected inspection timing | Unpermitted work can surface at resale |
| Commissioning | Refrigerant charge verification, airflow measurement, written report | A correct installation is what actually delivers performance |
| Old equipment removal | Disposal of the old system and any decommissioning | Otherwise it becomes your problem on install day |
| Warranty terms | Parts, labour, registration deadline, what voids coverage | Registration windows are easy to miss |
Where will the outdoor unit go, and how will noise and drainage be handled?
Walk the property with the contractor and agree on the exact location before signing. The outdoor unit needs clear air on the intake and discharge sides, room for a technician to open panels, and separation from the wall so vibration is not transmitted into the framing. It should sit raised on a pad or a wall bracket so that defrost meltwater drains away and so the coil is not sitting in standing water or leaf debris during a wet week.
Ask specifically how the unit will be isolated: rubber isolation pads under the feet, a bracket with vibration dampening if wall mounted, and refrigerant line sets that are supported rather than left to buzz against siding. In a townhouse, duplex or a lot with a narrow side yard, the location decision is also a neighbour decision. Ask where the unit faces and whether the contractor has considered a bedroom window across the property line.
Placement under a roof edge with no gutter is a classic mistake in this climate: runoff drips directly onto the top of the unit through the entire winter. Ask what protects the unit from roof runoff, and whether any leaf screening near a cedar hedge is warranted. Also confirm clearances from gas meters, electrical services and any dryer or combustion vents, since minimum separations apply.
What does a Metro Vancouver installation need that a quote elsewhere might not?
Our climate is mild and wet rather than deeply cold, which is genuinely favourable for heat pumps: the hours spent below a typical balance point are relatively few compared with the interior of the province, so a well-sized system carries most of the heating season on its own. But the wet part matters. Persistent damp means more defrost cycles, more meltwater, and more attention needed on drainage, pad height and corrosion protection near the coast where salt air is a factor.
The housing stock is the second local factor. Much of Burnaby, New Westminster, East Vancouver and North Surrey is postwar housing with ductwork that was designed around a hot furnace. A heat pump delivers a larger volume of cooler air, so undersized returns and constricted trunk lines that were tolerable before become audible and uneven afterward. Ask whether the contractor evaluated the existing duct system and whether any duct modification is included. A quote that assumes the ducts are fine, without measuring, is taking a risk on your behalf.
Strata and density are the third. In a townhouse or a low rise, the outdoor unit location, any wall penetration and often the visual appearance require strata approval, and the process takes time. Ask whether the contractor will supply the technical details your strata council needs, and build the approval timeline into your expectations rather than discovering it the week of installation.
Finally, permits. Municipalities across Metro Vancouver require permits for this class of work, and the electrical portion carries its own permit and inspection. Confirm in writing who applies, and get the permit numbers. Unpermitted mechanical or electrical work has a way of surfacing during a future sale or an insurance claim.
What questions should I ask about installation quality, commissioning and warranty?
Two identical pieces of equipment can perform very differently depending on how they were installed. The refrigerant charge must be verified against the manufacturer’s method for the actual line set length, the system must be evacuated properly before charging, and airflow across the indoor coil must be measured rather than assumed. Ask for a written commissioning report showing the measured values. A contractor who commissions systems properly is happy to hand you the numbers.
On warranty, ask three things: what the manufacturer covers on parts, what the contractor covers on labour, and whether registration within a deadline is required to keep full coverage. Registration windows are commonly short after the installation date and are easy to miss. Ask who submits the registration. Also ask what maintenance the manufacturer expects in order to keep coverage valid, and get that in writing rather than as a verbal reassurance.
Ask about licensing directly. In British Columbia, refrigerant work requires appropriate certification, gas work on any furnace being retained or removed is restricted to a licensed gas fitter, and electrical work is restricted to a licensed electrical contractor. BC Wide Home Services Ltd is a TSBC-licensed contractor holding licences LGA0090068 and CGA0028029, and we service a wide range of heat pump brands as an independent contractor rather than as a factory-authorised dealer of any single manufacturer. Ask any contractor you are considering to state their licence numbers on the quote.
One more practical question: who answers the phone after the install if something is not right? Ask what the response process looks like in the first heating season, when small commissioning adjustments are most often needed.
When should I call a licensed technician instead of sorting it out myself?
As a homeowner you may change or clean filters, keep the outdoor unit clear of leaves, snow and vegetation, gently rinse the outdoor coil with low-pressure water when the system is off, keep condensate drain areas clear, and operate your thermostat. Everything past that point involves refrigerant, gas or electricity and is restricted work in British Columbia.
Call a licensed technician if the outdoor unit ices over heavily and does not clear after a defrost cycle, if the system runs constantly without reaching setpoint, if you hear grinding, screeching or hard clunking, if a breaker trips repeatedly, if you see oily residue near refrigerant connections, if there is water pooling around the indoor unit, or if you smell burning. Repeated breaker trips in particular should never be reset again and again — that is a fault indication, not an inconvenience.
If your system is a hybrid that retains a gas furnace, or if you also have a gas water heater or fireplace, treat gas and carbon monoxide symptoms as an emergency. If you smell gas, leave the building, and call the gas utility emergency line and 911 from outside. Working carbon monoxide alarms on every sleeping level are essential in any home with combustion appliances, and any combustion equipment retained as backup heat should be inspected by a licensed gas fitter on a regular schedule.
For questions about a quote you have received, or to have a heat pump properly sized and installed in Metro Vancouver, call BC Wide Home Services Ltd at (604) 473-9690. We have been serving the Lower Mainland since 1999 from Burnaby, and we will put the sizing calculation, electrical scope and permit plan in writing before you commit to anything.
Frequently asked questions
Do I need an electrical panel upgrade for a heat pump?
Not always, but you need it checked before you sign. A licensed electrical contractor performs a load calculation on your existing service, accounting for the heat pump, any electric backup heat, and existing loads such as a range, water heater or vehicle charger. Many Metro Vancouver homes accommodate a heat pump on the existing service, and many older ones do not. Insist that the quote state whether the price assumes the existing panel is adequate, and how an upgrade would be handled if one is required.
Can a heat pump heat my house through a Metro Vancouver winter on its own?
In much of the Lower Mainland a correctly sized cold-climate system carries the large majority of the heating season by itself, because our winters are mild and wet rather than deeply cold. Backup heat still matters for the coldest nights and for defrost recovery. Ask the contractor where the balance point of the proposed system falls for your specific house, and what provides heat below it — electric elements, a retained gas furnace in a hybrid setup, or existing baseboards.
How do I know whether the heat pump is sized correctly?
Ask for the heat loss calculation as a document, and check that it is room by room and lists the design conditions used. If the contractor sized the system from square footage or by matching your old furnace, that is not a calculation. Oversizing causes short-cycling, uneven comfort and poor summer dehumidification; undersizing means constant running and heavy reliance on backup heat. The calculation is the only evidence that the size was engineered.
Is my existing ductwork suitable for a heat pump?
Sometimes, and it needs to be measured rather than assumed. A heat pump moves a larger volume of cooler air than a furnace, so ducts and returns that were adequate before can become noisy or unable to distribute heat evenly. Ask whether the contractor evaluated static pressure and return air capacity, and whether any duct sealing, resizing or additional returns are included in the quoted scope.
Do I need a permit to install a heat pump in Metro Vancouver?
Yes, permits apply in the municipalities across the region, and the electrical portion of the work carries its own permit and inspection. Confirm in writing who applies for each permit and ask to receive the permit numbers. Unpermitted mechanical or electrical work can create problems during a future sale, a home insurance claim, or a strata alteration review.
Is it normal for the outdoor unit to steam and drip in winter?
Yes. The outdoor coil accumulates frost in our damp winters, and the system periodically reverses briefly to melt it off. Visible steam, a short pause in heating and meltwater under the unit are all normal defrost behaviour. What is not normal is a thick ice buildup that does not clear after a defrost cycle, or meltwater that pools and refreezes on a walkway — the first needs a technician, the second needs better drainage at the pad.
What should I ask about the outdoor unit location in a townhouse or strata?
Ask exactly where the unit will sit, how far it stands off the wall, how it is isolated for vibration, and how meltwater drains away. Then ask whether your strata requires approval for the location, any wall penetration or the visual change, and whether the contractor will provide the technical documentation the strata council needs. Approval timelines are the most common cause of a delayed strata installation.
What is commissioning, and why should it be in my quote?
Commissioning is the set of measurements and adjustments made after installation: verifying refrigerant charge for the actual line set, confirming proper evacuation, measuring airflow across the indoor coil, and checking control and staging behaviour. It is what turns correctly chosen equipment into a system that actually performs. Ask for a written commissioning report with the measured values, and treat its absence from a quote as a meaningful difference between bids.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
Is a heat pump worth it in Vancouver?
What rebates are available for heat pumps in BC?
Should I get a ducted heat pump or ductless mini-split?
How long does a heat pump last?
Do heat pumps work in cold weather?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


