★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Radiant Floor Heating Installation Cost in Langley

Boilers

Radiant Floor Heating Installation Cost in Langley
Home › Radiant Floor Heating Installation Cost in Langley

Radiant Floor Heating Installation Cost in Langley

Key takeaways

  • Ballpark for the boiler side in Langley: $7,000 to $15,000 installed for a condensing gas boiler, before GST. This is a range for orientation, not a quote.
  • Tubing loops, manifolds, zone controls and floor work are priced per project and depend on heated floor area, new build versus retrofit, installation method and floor finish.
  • Radiant floors run on low water temperatures, which is exactly the condition in which a condensing gas boiler works at its best.
  • New builds, basement slabs and full renovations are the strongest fit; retrofitting under an existing finished floor costs more and delivers less.
  • Gas piping, venting and boiler installation require a licensed gas fitter under permit, and carbon monoxide alarms belong on every level.
  • For exact pricing on your home, call BC Wide at (604) 473-9690 or email info@bcwide.ca for a free written quote.

For a Langley home, gas-fired radiant floor heating is priced in two parts. The boiler side, meaning a condensing gas boiler installed, vented and commissioned, sits in a ballpark range of $7,000 to $15,000 before GST. These are ballpark figures for orientation only and are NOT a quote; an accurate price needs a site visit. If you choose a combi boiler that also makes your domestic hot water, the boiler side moves to a ballpark of roughly $8,000 to $14,000 and up. The second part is the distribution side: the tubing loops, manifolds, controls and floor work. There is no honest single range for that half, because it depends almost entirely on how much floor you are heating, whether the home is a new build or a retrofit, how the tubing goes in, and what finish sits on top. This page explains both halves, what pushes each one up or down, and what a proper Langley quote should contain.

How much does radiant floor heating cost in a Langley home?

Think of the job as a heat source plus a heat delivery network. The heat source is the boiler and everything connected to it: the vent, the condensate drain, the gas connection, the expansion tank, air and dirt separation, the circulator pumps and the control that sets water temperature. That is the part we can anchor with ballpark figures. The delivery network is the tubing in or under the floor, the manifolds that feed each loop, the zone actuators, the thermostats and floor sensors, and whatever floor build-up the chosen method needs.

The delivery side varies so much between a slab poured in a new Willoughby build and a retrofit under hardwood in an older rancher that any single number would mislead you. So here is what we can responsibly put ranges on, followed by a breakdown of what each line of a quote actually covers.

  • Condensing gas boiler, boiler side only: ballpark $7,000 to $15,000 installed, before GST.
  • Gas combi boiler serving both the radiant floor and your domestic hot water: ballpark $8,000 to $14,000 and up.
  • New gas line to the boiler location, short and accessible run: ballpark $500 to $1,500.
  • New gas line on a long or difficult run through finished space: ballpark $1,500 to $3,000 or more.
  • Tubing loops, manifolds, zone controls and floor work: quoted per project after a heat-loss calculation and loop layout, as explained in the next section.
Line itemWhat it coversHow it is priced
Boiler and near-boiler pipingCondensing boiler, circulators, expansion tank, air and dirt separation, mixing and outdoor reset controlWithin the anchored boiler range; varies with boiler type and venting
Venting and condensateVent route and termination, condensate neutralizer and drain path or pumpUsually inside the boiler range; long or awkward routes push it higher
Gas supplyAssessment of the existing line and a new or upsized branch if neededSeparate range only when a new line is required
Tubing loopsOxygen-barrier PEX in a slab, thin pour, panels or under-floor platesDriven by heated floor area and installation method
Manifolds and zoningSupply and return manifolds, actuators, room thermostats, floor sensorsDriven by the number of rooms and zones
Floor workInsulation, pour or panels, levelling and finish flooringOften a separate trade; must be clearly split out in the quote
Permits and commissioningGas permit, any hydronic permit, pressure testing, balancing and startupPermit fees are set by the permitting authority; labour is in the quote

What moves the price of a radiant floor system?

Two Langley homes of the same size can land far apart on price. The difference is almost never the boiler badge; it is the conditions around the installation. These are the factors that move the number most, roughly in order of how often they matter on real jobs.

  • Heated floor area and number of zones. More floor means more tubing, more loops, larger or additional manifolds and more labour. Every room that gets its own thermostat adds an actuator, a thermostat and wiring.
  • New build versus retrofit. In new construction the tubing goes down before the slab is poured or the subfloor is closed, so labour is efficient. In a retrofit, floors come up or ceilings below come down, and that disruption is where cost climbs fastest.
  • Installation method. Tubing embedded in a slab is the least labour per square metre. A thin overpour adds a pour and curing time. Low-profile panels add material. Plates stapled up from below save the finished floor but need open joist bays.
  • Floor finish. Tile and stone move heat well. Engineered wood works with a careful design. Thick carpet and pad behave like insulation and can force tighter loop spacing or warmer water, which changes the design.
  • Under-slab and edge insulation. A slab without insulation underneath sends much of its heat into the ground. Adding insulation during a new pour is straightforward; adding it afterwards is effectively impossible.
  • Boiler venting. A short sidewall vent close to the boiler is simplest. A long route, a roof termination, or a boiler location far from an exterior wall adds materials and labour.
  • Gas line capacity. A home already running a furnace, range, fireplace and water heater may not have a gas line that can carry one more appliance, so a new or upsized line becomes part of the job.
  • Condensate routing. Condensing boilers produce slightly acidic condensate that needs a neutralizer and a path to a drain. With no floor drain nearby, a condensate pump is added.
  • Electrical. The boiler, circulators and zone controls need a dedicated circuit and low-voltage wiring. A panel with no spare capacity or space brings in extra electrical work.
  • Domestic hot water. Adding an indirect hot water tank, or choosing a combi boiler instead of a heat-only boiler, changes the boiler side of the quote.
  • Access, disposal and code upgrades. Tight crawlspaces, finished basements, removal of an old appliance, and bringing existing venting or gas piping up to current code all show up as line items.

Which radiant floor installation method suits your floor?

The method is the single biggest lever on the floor side of the price, and it is usually dictated by the house rather than chosen freely. A slab responds slowly because it stores a lot of heat, which suits steady weather and an outdoor reset control. Plates and panels respond faster but deliver less heat per square metre, so they need a more careful design in rooms with large windows or exterior walls.

MethodBest suited toFloor height impactDisruption
Tubing in a concrete slabNew builds, basement slabs being poured, garages converted to living spaceNone beyond the slab itselfLow in new construction; not practical under an existing slab
Thin overpour on a wood subfloorMain floors during a full renovationRaises the floor noticeably; doors, stairs and transitions may need adjustingModerate; the structure must be checked for the added weight
Low-profile grooved panels on the subfloorRenovations where a pour is not wantedSmall rise, less than a pourModerate; finish flooring goes directly on top
Heat transfer plates under the subfloorMain floors above an unfinished basement or crawlspaceNone on the finished floorLow upstairs, but joist bays must be open from below

Who is radiant floor heating a good fit for in Langley?

Radiant floors make the most financial sense when the floor is already open. That points to three kinds of project. The first is new construction, including custom homes on larger rural lots in the Township, where the tubing can go into the slab or subfloor before anything is finished. The second is the basement: many homes here have full basements with bare concrete floors that stay cold even when the rest of the house is comfortable, and a basement being finished, lowered or re-poured is an ideal moment to add loops. The third is a full renovation where the flooring on a whole level is coming up anyway.

It is a weaker fit for a single room retrofit under an existing finished floor in a home where the gas furnace is working well. The cost per heated room is high, and the comfort gain may not justify it. It is also worth remembering that radiant floors heat but do not cool. If you want central air conditioning, the home still needs ductwork or a ductless system, so many Langley households keep a gas furnace and ducts for the upper floors and cooling, and use a boiler with in-floor heat for the basement or main-floor tile areas.

Why does a condensing gas boiler pair so well with in-floor heat?

A condensing boiler squeezes extra heat out of its exhaust by cooling the flue gases until the water vapour in them condenses. That only happens when the water returning to the boiler is cool enough. Radiant floors are designed to run on low water temperatures, because a large warm surface does not need hot water to heat a room. The result is that a boiler serving a well-designed floor can stay in its condensing range for most of the heating season, which is where its efficiency rating actually shows up on your gas bill.

An outdoor reset control makes this work in practice. It raises the water temperature on cold nights and lowers it on mild days, so the floor tracks the weather instead of cycling hard. If the boiler also serves a hotter load, such as panel radiators or an indirect hot water tank, a mixing valve protects the floor loops from water that is too hot for the finish.

Water quality matters too. Metro Vancouver’s municipal water is soft, so limescale inside the boiler is rarely the problem here. Sludge and corrosion are. Older radiant systems installed with tubing that lacked an oxygen barrier let oxygen into the water, which corrodes iron and steel parts and fills the system with sludge. A modern installation uses oxygen-barrier tubing, a dirt or magnetic separator, a properly filled and treated system, and an inhibitor recommended for the boiler.

What should a radiant floor heating quote include?

A single number on a page is not a radiant quote. Because the floor side varies so much, the only way to compare two quotes is to check that they cover the same scope. A complete quote for a Langley home should spell out the following.

  • A room-by-room heat-loss calculation, so the boiler is sized to the home’s real heat loss rather than its square footage.
  • A loop layout showing where each loop runs, its spacing, and which manifold feeds it.
  • The tubing type, confirmed as oxygen-barrier, and the installation method for each area.
  • Manifold locations and the number of zones and thermostats, including any floor sensors.
  • The boiler type (heat-only or combi) and whether an indirect hot water tank is included.
  • The vent route and termination location, and the condensate plan.
  • A gas line assessment and whether a new or upsized line is included.
  • The control strategy: outdoor reset, mixing, and how the system talks to any existing furnace thermostat.
  • A pressure test of the loops before they are covered, and how that test is recorded.
  • Who is responsible for insulation, the pour or panels, and the finish flooring.
  • Which permits are required and who pulls them.
  • Commissioning, balancing and startup, plus removal and disposal of any old equipment.
  • A clear list of exclusions, so nothing surprises you halfway through.

What is different about radiant heating in Langley homes?

Langley is two municipalities, the City of Langley and the Township of Langley, and the address decides which one handles building and any hydronic permits. Gas permits are issued through Technical Safety BC or the local authority depending on the area, and a licensed installer confirms which applies before work starts. Permit fees are set by each municipality or by Technical Safety BC, not by the contractor.

The climate matters to the design. Langley sits further inland than Vancouver or Burnaby, and many homes here see colder nights, more frost and the occasional outflow wind event during a winter cold snap. A radiant floor needs to be designed for those nights, not for an average January day, which is exactly what the heat-loss calculation is for.

The housing stock is varied. Many homes in Willoughby and Walnut Grove are newer two-storey houses with basements and an existing forced-air furnace, which makes a basement radiant zone off a new boiler a common project. Older ranchers in areas like Brookswood and Murrayville often have crawlspaces or unfinished basements where under-floor plates can go in without disturbing the finished floor above. Rural properties in the Township may include acreage homes, detached shops and larger floor areas. If you own a character home in Fort Langley, any heritage questions go to the municipality before work is planned. In a townhouse or other strata property, check your bylaws with the strata council before committing to any work.

One more local detail: homes on municipal water generally have soft water, but some rural properties on private wells can have different water chemistry. We check the fill water before commissioning so the closed loop starts clean and properly treated.

Which parts can a homeowner do, and when do you need a licensed technician?

Homeowners can make the design decisions, choose the floor finish, clear and prepare the space, coordinate with a flooring trade, set and program the thermostats, read and note the pressure shown on the boiler gauge, keep the outdoor vent and air intake clear of leaves and snow, and test carbon monoxide alarms.

In BC, all gas piping, boiler installation, venting and combustion setup must be done by a licensed gas fitter under permit. Most electrical work requires a licensed electrician. Connecting hydronic piping to the boiler, filling and purging the loops, pressure testing and commissioning belong with a qualified hydronic technician. BC Wide is an independent contractor licensed by Technical Safety BC (LGA0090068, CGA0028029), serving Metro Vancouver since 1999.

Call a licensed technician if the boiler pressure keeps dropping, some loops stay cold while others are warm, you hear gurgling or rushing water, there is water around the boiler, the display shows a fault you cannot clear, or the burner cycles on and off rapidly. If an existing boiler system has lost heat entirely, we offer same-day service where we can, but we will be honest about timing and never promise a guaranteed arrival window.

Why does only a site visit give you a real price?

Everything that moves a radiant floor price is physical: the heat loss of your walls and windows, the capacity of your gas line, the route a vent can take, the space in your electrical panel, the structure under your floors and the finish you want on top. None of that can be measured from a phone call or a photo. A free in-home estimate lets us calculate the heat loss, sketch the loop layout, check the gas and venting, and give you a written quote that separates the boiler side from the floor side so you can see exactly where the money goes.

To repeat plainly: the figures on this page are ballpark prices for orientation, not a quote. For exact pricing on your Langley home, call BC Wide at (604) 473-9690 or email info@bcwide.ca for a free written quote. We will book a time to see the home, walk through the options with you, and put the full scope in writing.

Gas & carbon-monoxide safety: A radiant floor system heated by a gas boiler is combustion equipment, so gas and carbon monoxide safety apply. Install carbon monoxide alarms on every level of the home and near sleeping areas, and test them regularly. If you smell gas, leave the house right away, do not operate light switches or appliances, and call your gas utility’s emergency line from outside. Keep the boiler’s vent and air intake terminals clear of snow, leaves and stored items. Never attempt gas piping, venting or boiler installation yourself; in BC that work must be done by a licensed gas fitter under permit.

Frequently asked questions

Is radiant floor heating worth it in a Langley home?

It is usually worth it when the floor is already open, such as in a new build, a basement being finished or a full renovation. In those cases the added cost of the loops is modest compared with the comfort of warm floors and the efficiency of a condensing boiler running on low water temperatures. It is harder to justify for one room under an existing finished floor.

Can I add radiant floor heating to just my basement?

Yes, and it is one of the most common radiant projects in Langley. A basement slab being poured or re-poured can take tubing directly, and a boiler can heat that zone while your gas furnace continues to heat the upper floors. Insulation under the new slab is important so the heat goes into the room rather than the ground.

Can I keep my gas furnace and add radiant floors?

Yes. Many homes keep the furnace and ductwork for the upper floors and for central air conditioning, and add a boiler for in-floor heat in the basement or tiled areas. The two systems need controls that coordinate so they are not fighting each other, which your installer should include in the design.

Does radiant floor heating work under hardwood?

Engineered wood generally works well over radiant heat when the system is designed with controlled water temperatures and the flooring maker’s guidance is followed. Solid hardwood needs more care because it moves with changes in moisture and temperature. Confirm the flooring product’s radiant suitability with its manufacturer before you buy.

Are there incentives for a high-efficiency gas boiler in Langley?

Incentive programs for high-efficiency heating equipment come and go, and eligibility rules change. Check the current programs before you sign, since some require pre-approval or specific paperwork. We can point you to where to confirm what applies to your home, but we do not quote incentive amounts.

Do I need a permit for radiant floor heating in Langley?

Yes. The gas boiler installation needs a gas permit, and the hydronic and building work may need permits from the City of Langley or the Township of Langley depending on your address. Permit fees are set by the municipality or Technical Safety BC, and your licensed installer should pull the gas permit.

How long does a radiant floor installation take?

It depends mainly on the method. In a new build, the tubing is sequenced with the construction schedule and the pour. A boiler installation in an existing home is usually a matter of days, while retrofit floor work takes longer because floors or ceilings have to be opened and restored. Your written quote should include a realistic schedule.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.
Are BC Wide technicians licensed and insured?
Yes. BC Wide holds a TSBC gas-fitting licence, our technicians are Red Seal certified for HVAC and gas, and we carry full liability insurance and WorkSafeBC coverage.
How can I book a service call?
Call (604) 473-9690, email info@bcwide.ca, or use the booking form on bcwide.ca. Most calls are answered the same business day and we offer next-day appointments for non-emergency work.
Do you offer free estimates?
Yes. Free in-home estimates are provided for boiler, furnace, heat pump and water-heater replacements. Diagnostic visits for repairs carry a flat service fee that is credited toward the repair if you proceed.
What brands do you service?
We service all major brands including Viessmann, Navien, IBC, Rinnai, Rheem, Bradford White, Weil-McLain, Laars, Baxi, NTI, Lennox, Carrier, Bryant, Goodman, Trane, York, Daikin, Mitsubishi Electric, AO Smith, Bosch, Noritz, Giant, GSW, John Wood, and Valor.
Do you offer government rebates for heat pumps?
Yes. We are a registered contractor for BC Hydro, FortisBC and federal Greener Homes rebates. A high-efficiency heat pump installation can qualify for up to $11,000 in combined rebates depending on your home and income.
How quickly can you replace a broken hot water tank?
Standard 40 or 50-gallon gas or electric tanks are typically replaced same-day or next-day from stock. Tankless water heaters and larger commercial units usually take 1–3 business days depending on parts availability.
Why should I choose BC Wide over other HVAC companies?
BC Wide Heating & Air Conditioning has been operating in Greater Vancouver since 1999 as a TSBC-licensed (LGA90068) HVAC and gas contractor. We specialise in furnaces, boilers, heat pumps and water heaters across every major brand, we give honest options instead of upselling, and our work is performed by experienced, certified staff — not subcontractors.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote