- The boiler side of a radiant floor job runs a ballpark $7,000 to $15,000 installed for a condensing gas boiler, or $8,000 to $14,000 and up for a combi boiler that also makes hot water. These are not quotes.
- Tubing loops, manifolds and floor work are priced from floor area, new build versus retrofit, and floor finish, so they need a site visit and a room-by-room heat-loss calculation.
- Radiant floors suit new builds, basements and full renovations best; a single-room retrofit under a finished floor costs more per heated room and delivers less.
- Radiant runs on low water temperatures, which is exactly the range where a condensing boiler condenses and does its best work.
- Gas piping, the boiler, venting and combustion setup are licensed work in BC, and permit fees are set by each municipality or Technical Safety BC.
- For exact pricing on your home, call (604) 473-9690 or email info@bcwide.ca for a free written quote.
Radiant floor heating in a West Vancouver home is really two projects priced together: the gas boiler that makes the heat, and the tubing, manifolds and floor work that deliver it. On the boiler side, a condensing gas boiler installed to run a radiant system usually lands in a ballpark range of $7,000 to $15,000 in Greater Vancouver, installed and before GST. These are ballpark figures for orientation only and they are not a quote; an accurate price needs a site visit. If you want one gas combi boiler to run the floors and also make your domestic hot water, the ballpark is $8,000 to $14,000 and up. The loop side has no honest single range, because it swings on how much floor you heat, whether the house is a new build or a retrofit, and what finish goes on top. This page explains exactly what moves that number, who radiant suits, and what a proper written quote from a TSBC-licensed contractor such as BC Wide (LGA0090068, CGA0028029) should spell out.
How much does radiant floor heating cost in West Vancouver?
Split the job in two and the pricing becomes much easier to reason about. The heat source is a gas boiler, and it has a well-understood ballpark. The distribution side, meaning the tubing loops, the manifolds that feed them, the circulator pumps and mixing controls, and whatever floor work is needed to get tubing into the floor, is where two West Vancouver homes of the same size can land a long way apart.
For the boiler: a condensing gas boiler replacement or new installation sits in a ballpark of $7,000 to $15,000 installed, and a gas combi boiler serving both the floors and the taps sits at $8,000 to $14,000 and up. If the mechanical room has no gas supply, or the existing line is too small for the new load, a new gas line adds a ballpark $500 to $1,500 where the run is short and accessible, and $1,500 to $3,000 or more where it is long or has to pass through finished space. All of these are wide installed ranges before GST, and none of them is a quote.
Any utility or government program that applies would come off afterwards. Programs change, so we check what currently applies when we prepare a written quote rather than promising anything in advance.
The table below shows how each line item is priced. We deliberately do not put a figure on loops, manifolds or floor work, because any number given without seeing the floor and the structure under it would be a guess.
| Line item | What it covers | How the ballpark is set |
|---|---|---|
| Condensing gas boiler | Boiler, venting, condensate drain, near-boiler piping and start-up | Anchored ballpark range given above; moves with venting route and access |
| Gas combi boiler | One appliance for floor heat and domestic hot water | Anchored ballpark range given above; moves with hot water demand and venting |
| New or upsized gas line | Piping from the meter or existing line to the boiler | Anchored ballpark range given above; moves with length and finished-wall access |
| Tubing loops | Tubing laid in or under the floor, one loop per area | Priced from floor area and loop count after a heat-loss calculation |
| Manifolds and zoning | Supply and return manifolds, zone valves or pumps, thermostats | Priced from the number of zones and manifold locations |
| Mixing and controls | Mixing valve or injection control, outdoor reset, floor sensors | Priced from the system design after the site visit |
| Floor work | Slab pour, thin topping, joist plates or panels, and the new finish | Priced after seeing the structure; often by the flooring or general contractor |
| Permits | Gas permit and any building permit | Fees set by the District of West Vancouver or Technical Safety BC |
What moves the price of radiant floor heating?
Most of the swing between two quotes comes from a short list of site conditions. When you compare estimates, check whether each of these has actually been priced or simply left out.
- Floor area and loop count: more heated floor means more tubing, more loops and larger or additional manifolds. Bathrooms, kitchens and entries full of cabinetry and fixtures need tighter, more fiddly layouts.
- New build versus retrofit: tubing tied to the reinforcing before a slab pour is the most straightforward installation there is. Retrofitting under an existing wood subfloor from below, with heat-transfer plates in the joist bays, or from above with low-profile panels or a thin topping, is far more labour for the same area.
- Floor finish: tile and stone move heat well and are natural partners for radiant. Engineered wood can work when the flooring maker approves it for radiant use. Thick carpet and heavy underlay slow the heat down and may call for warmer water or tighter tubing spacing.
- Boiler venting: a condensing boiler produces cool, acidic exhaust that runs through manufacturer-approved plastic venting, usually out a sidewall or through the roof. An old masonry chimney cannot simply be reused for it, and a long or awkward vent route adds labour.
- Gas line sizing: the boiler needs enough gas volume at the right pressure. Older piping sized for a smaller appliance is one of the most common hidden costs we find in established neighbourhoods.
- Condensate routing: condensing boilers make acidic water that has to reach a drain, normally through a neutralizer. A mechanical room with no nearby drain may need a condensate pump.
- Electrical: the boiler, circulator pumps, zone controls and thermostats need power and control wiring, and new circuits are a job for a licensed electrician.
- Permits and inspections: a gas permit covers the boiler and gas piping, and structural or floor work can bring a building permit. Permit fees are set by each municipality or by Technical Safety BC.
- Access and disposal: steep driveways, long stairs down to a lower-level mechanical room, and removal of an old boiler or tank all take time and hands.
- Code upgrades: an older installation may need venting, bonding, carbon monoxide alarm or clearance corrections before a new appliance can pass inspection.
Who is radiant floor heating a good fit for?
Radiant floors are at their best when the floor is already open. In a new build or a full-house renovation, tubing goes in while the structure is exposed, loops can be laid out room by room, and the boiler can be sized from a proper heat-loss calculation instead of being matched to whatever was there before. This is where radiant gives the most comfort for the money.
Basements are the second strong case. A concrete floor that feels cold and damp through the winter changes character completely with radiant under it, and in a walk-out lower level on a sloped lot the slab is often the coldest surface in the house. When the basement is being finished anyway, adding tubing at that stage is far easier than adding it later.
Single-room retrofits under a finished floor are where radiant is hardest to justify. You pay for access, patching and a new finish for a comparatively small heated area, and you still need a heat source that can supply it. If the home already has a gas boiler running hydronic radiators or baseboards, a bathroom or kitchen zone can sometimes be added off the existing system with a mixing arrangement, which changes the arithmetic considerably. That is a site-visit question, not a phone question.
Radiant floors are also slow by nature. They warm the mass of the floor first and the room second, so they reward steady temperatures rather than deep setbacks. Homeowners who want to heat a room quickly for an hour in the evening may be happier with a forced-air zone, and we will say so if that is the better fit.
What is different about radiant heating in West Vancouver homes?
Many homes here, from Ambleside and Dundarave up into the British Properties, sit on sloped lots with lower levels partly set into the hillside and main floors opening onto large windows facing the water. That combination creates two different heating problems in one house: a cool, earth-contact lower slab and a glass-heavy main floor that loses heat quickly on a cold, clear night. A good radiant design treats them as separate zones with their own thermostats rather than one loop plan for the whole house.
West Vancouver also has a large stock of mid-century West Coast modern and post-and-beam homes, and some of them were built with radiant tubing already cast into the concrete. Where that original tubing is still in service, the real question is whether it can be tested, cleaned and connected to a new condensing boiler, or whether it has reached the end of its life. That takes a pressure test and an honest look at the manifold area, not an assumption in either direction.
Our coastal climate matters too. Winters are mild and wet, with long shoulder seasons and occasional cold snaps. Radiant floors suit that pattern well because they run for long periods at low output, which keeps a condensing boiler in its efficient operating range for most of the heating season.
Metro Vancouver water is soft, so hydronic trouble here is rarely limescale. It is sludge and corrosion: older tubing without an oxygen barrier lets oxygen into the loop, which attacks iron and steel components and leaves sludge that clogs manifolds and boiler heat exchangers. Connecting a new boiler to older loops usually calls for flushing, a system cleaner and a dirt separator or filter first, and that work belongs in the quote.
If your home is in a strata building, check your bylaws and talk to your council before planning floor work or a new vent through an exterior wall. If the house has a heritage designation, or you are not sure, ask the District of West Vancouver what applies before work starts. We do not tell owners what their strata or a heritage listing allows; those answers come from the bodies that set the rules.
What should a radiant floor heating quote include?
A radiant quote that is one line and one number is not a quote you can compare. Ask for these items in writing:
- A room-by-room heat-loss calculation, so boiler size and tubing spacing come from your house rather than a rule of thumb.
- The tubing layout: which rooms are heated, how many loops, and where the manifolds will sit.
- The boiler, its venting route and termination point, the condensate drain plan, and whether a neutralizer or condensate pump is included.
- How water temperature is controlled, whether by mixing valve or injection, and whether outdoor reset control is part of the design.
- Zoning: how many zones, which thermostats, and whether floor sensors are included for tile and wood rooms.
- Gas piping: whether the existing line was checked, and whether upsizing or a new run is included.
- The electrical scope and who is doing it.
- Permits, inspections, pressure testing, filling, purging and commissioning.
- Floor work: exactly what is included and what the flooring or general contractor is responsible for.
- Removal and disposal of old equipment, cleaning of any existing loops, and a plain list of exclusions.
- Warranty terms as the manufacturer writes them, plus the installer’s own workmanship terms.
Why can’t anyone give an exact radiant floor price over the phone?
Because the most expensive variables are hidden until someone looks. The size of the gas line behind a finished wall, whether the mechanical room has a drain, where a vent can properly terminate on a tight hillside lot, whether the joist bays are clear or full of ducts and wiring, and whether old in-slab tubing still holds pressure: none of that is visible from a phone call or a photo.
The heat-loss side is the same. Two homes with identical floor area can need very different tubing spacing and boiler capacity depending on window area, insulation, exposure to wind off the water and how much of the lower floor sits below grade. Guessing that from a square-footage figure is how systems end up short of heat in the rooms along the glass, or oversized and short-cycling everywhere else.
A site visit lets us measure, test and design, and it turns the ballpark on this page into a written number you can hold us to.
What can a homeowner do, and what needs a licensed technician?
Gas work and most electrical work in BC are legally restricted to licensed trades. Here is how a typical radiant project divides up, so you know where your own effort helps and where it has to stop.
| Task | Who does it |
|---|---|
| Decide which rooms to heat and choose floor finishes | Homeowner, with the installer’s advice |
| Check strata bylaws or heritage questions | Homeowner, with strata council or the municipality |
| Clear the mechanical room and work areas | Homeowner |
| Room-by-room heat-loss calculation and loop design | Heating contractor |
| Laying tubing and setting manifolds | Heating contractor |
| Gas piping, boiler installation, venting and combustion setup | Licensed gas fitter only |
| New circuits and wiring for boiler, pumps and controls | Licensed electrician |
| Pressure testing, filling, purging and commissioning | Installer |
| Watching the boiler pressure gauge and reporting changes | Homeowner |
| Testing carbon monoxide alarms monthly | Homeowner |
When should you call a licensed technician about radiant heat?
If you already have radiant floors, call a licensed technician when you notice any of the signs below. We offer same-day service where we can, depending on the day’s schedule and the parts involved, and we will not promise an arrival window we cannot keep. A single cool zone is rarely urgent, but steady pressure loss or any combustion concern should not wait.
- One zone stays cold while the others heat normally.
- The boiler pressure gauge keeps dropping between visits, which can point to a leak in a loop or at a fitting.
- The boiler short-cycles, runs noisily, or the pipes gurgle in a way that suggests air in the loops.
- Dark or sludgy water appears when a technician bleeds or drains the system.
- Water stains, damp patches or unexpected warm spots appear in walls, ceilings or floors.
- Any gas smell, a carbon monoxide alarm sounding, or scorching near the boiler: leave the house first and call from outside.
How do I get an exact radiant floor heating price for my West Vancouver home?
Book a free in-home estimate. We will look at the mechanical room, the gas supply, the venting options, the floors you want heated and the structure under them, run a heat-loss calculation, and give you a written quote that separates the boiler side from the loop and floor side so you can see exactly where the money goes.
To restate it plainly: every figure on this page is a ballpark price for orientation, not a quote. For exact pricing on your home, call BC Wide at (604) 473-9690 or email info@bcwide.ca for a free written quote. BC Wide Home Services Ltd is an independent TSBC-licensed contractor (LGA0090068, CGA0028029) that has served Metro Vancouver from Burnaby since 1999. We are not a factory-authorized dealer for any manufacturer; we service and install the brands that suit your home.
Frequently asked questions
Is radiant floor heating expensive to install in West Vancouver?
It costs more upfront than simply replacing a heat source, because you pay for both the boiler and the distribution in the floor. The boiler side alone sits in a ballpark of $7,000 to $15,000 installed for a condensing gas boiler, and loops and floor work are added on top based on floor area and construction. It is most cost-effective in new builds, basements and full renovations where the floor is already open.
Can radiant floor heating go under hardwood?
Often, yes, as long as the flooring maker approves the product for radiant use. Engineered wood is usually an easier choice than solid hardwood because it moves less with temperature changes. Floor sensors and controlled water temperatures protect the finish, and the installer should confirm the flooring’s limits before designing the loops.
Do I need a new boiler to add radiant floors?
Not always. If you already have a gas boiler with spare capacity, a radiant zone can sometimes be added with a mixing arrangement that lowers the water temperature for the floor. If the boiler is older, undersized or non-condensing, replacing it at the same time is usually the better plan, and a site visit tells us which applies.
Are there rebates for radiant floor heating in BC?
Rebate and incentive programs in BC change from year to year, and eligibility usually depends on the equipment and the home rather than on radiant floors themselves. We check which programs currently apply when we prepare your quote and explain the paperwork involved. We do not state amounts in advance because they depend on the program in force at the time.
Do I need a permit for radiant floor heating in West Vancouver?
The gas boiler and gas piping need a gas permit, which your licensed gas fitter takes out, and structural or floor work may need a building permit from the District of West Vancouver. Permit fees are set by the municipality or by Technical Safety BC. A licensed contractor should handle the gas permit and inspection as part of the job.
How long does a radiant floor installation take?
It depends mostly on the floor work. The boiler side of a typical job is a matter of days, while a slab pour or a thin topping adds curing time before finishes can go down. Your written quote should include a realistic schedule for your specific home.
Does radiant floor heating work in rooms with big windows?
Yes, but large windows raise heat loss and may need tighter tubing spacing or a separate zone along the glass. That is why a room-by-room heat-loss calculation matters so much in West Vancouver view homes. Without one, the rooms along the windows are the first to feel short of heat.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
Are BC Wide technicians licensed and insured?
How can I book a service call?
Do you offer free estimates?
What brands do you service?
Do you offer government rebates for heat pumps?
How quickly can you replace a broken hot water tank?
Why should I choose BC Wide over other HVAC companies?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


