★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Relocating a Tankless Water Heater to an Exterior Wall

Water Heaters

Relocating a Tankless Water Heater to an Exterior Wall
Home › Relocating a Tankless Water Heater to an Exterior Wall

Relocating a Tankless Water Heater to an Exterior Wall

Key takeaways

  • Relocating a gas tankless unit to an exterior wall is usually realistic in our climate, but it is a mechanical rebuild, not a swap: the gas piping, venting, combustion air, electrical, bonding and condensate all move with it.
  • The appliance is often the smallest part of the job. Most of the labour and most of the cost sit in gas line sizing, vent termination and getting power and drainage to the new wall.
  • Outdoor-rated tankless units have built-in freeze protection that depends on electrical power, so the exposed water piping and the power supply become safety items, not preferences.
  • The honest answer is frequently do it while you are replacing the appliance anyway, because the relocation labour is nearly identical and you avoid paying to move a unit that is near the end of its life.
  • Gas work and most electrical work in BC is restricted to licensed trades, and the relocation needs a permit and inspection through the authority having jurisdiction.
  • Clearances, vent sizes, vent run lengths and gas pipe sizing come from the code and from the manufacturer’s installation instructions for your actual model, and are confirmed on site.

In most Metro Vancouver homes, yes, relocating a gas tankless water heater to an exterior wall is realistic, and it is one of the more common reasons homeowners call us when they are finishing a basement, adding a suite or reclaiming a mechanical closet. The honest qualifier is that it is a bigger job than a straight replacement, because the appliance is the easiest thing to move and everything attached to it is not. A relocation means new gas piping sized for the run, a new vent and a new termination point in a compliant location, combustion air sorted out, a dedicated electrical supply and bonding at the new wall, a condensate path that actually drains somewhere legal, new hot and cold water piping back to the existing distribution, a permit, and an inspection. Whether your existing indoor unit can even live outside depends on the model: some product families are built in both indoor and outdoor versions, some indoor units can be converted with a manufacturer’s own kit, and some cannot go outside at all. That is the first thing a technician confirms on site, before anything else is discussed.

Can my existing tankless water heater actually go on an exterior wall?

It depends entirely on how the unit was built and listed. Gas tankless water heaters are certified either for indoor installation or for outdoor installation, and that listing is not a suggestion. An indoor unit mounted outside without the manufacturer’s approved conversion is an uncertified installation, which an inspector will fail and which puts you outside the appliance warranty.

There are three realistic paths. The first is that your unit already has an outdoor-listed sibling and yours is the indoor version, in which case it stays indoors and moves to a different indoor wall instead. The second is that the manufacturer publishes a conversion kit that makes the indoor unit suitable for outdoor use. Rheem, for example, publishes such a kit for certain indoor models, and Bradford White builds the Infiniti K Series in both indoor and outdoor versions. The third is that the unit simply is not a candidate, and the conversation becomes a replacement with an outdoor-listed appliance.

Among the brands we service, the families we commonly see in Metro Vancouver homes are Bradford White’s Infiniti K, L, GR and GS Series and Rheem’s IKONIC S and SR Series, the Prestige RTGH condensing line including the Canadian variants, the RTG and RTG-R non-condensing units, and the retail Performance Platinum line. Which of those can be installed or converted for outdoor use, and what is required to do it, is manufacturer-published information that we verify against the installation instructions for your exact model rather than from memory. BC Wide is an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029. We service these brands; we are not a factory-authorised dealer for any of them.

What gets assessed on site before anyone can price the move?

A relocation cannot be quoted honestly over the phone, and any number given without a site visit is a guess. The assessment is mostly about the new wall and the path between the old location and the new one.

A technician walks the gas line from the meter forward, because the existing pipe was sized for the old run and the new run is longer, or takes a different route, or picks up an elbow count that changes the pressure drop. They look at what else is on that gas system, since a furnace, a range and a fireplace on the same branch all draw at once. They look at the proposed termination area for the vent or, on an outdoor unit, for the exhaust outlet itself, and check what is nearby: windows that open, doors, soffits, mechanical intakes, gas meters, property lines, decks and walkways, and the neighbour’s building if you are on a narrow lot. They check where power can come from and whether the panel has a spare position. They check where condensate can be routed on a condensing unit and whether it needs neutralising and a pump. Then they look at the water piping and where the new hot and cold connections rejoin the house.

  • Gas: existing pipe size, total developed length of the new run, the load of every other appliance on the system, and whether the meter and regulator can support it.
  • Venting and termination: on an indoor relocation, the new vent route and where it terminates. On an outdoor unit, the clearance zone around the appliance’s own exhaust.
  • Combustion air: how the appliance gets air in its new home, which is different for a direct-vent indoor unit, an indoor unit drawing from the room, and an outdoor unit.
  • Electrical: a supply to the new location, a means of disconnect, bonding of the gas and water piping, and whether the ignition and freeze-protection load can be supported.
  • Condensate: on a condensing unit, a drain path with the right slope, the right material, neutralisation where required, and a pump if gravity will not do it.
  • Water piping: the route back to the existing hot and cold distribution, insulation of any exposed run, and whether a recirculation line exists or is being added.
  • Access and finishes: how the old location gets closed up, what walls or ceilings get opened, and how the appliance gets to the new wall.
  • Permits: the application to the authority having jurisdiction and the inspection that closes it out.

What has to move with the appliance?

This is the part homeowners underestimate, and it is the part that separates a complete quote from an incomplete one. Every item below is real work with real materials. If a written scope does not mention one of them, it is worth asking why before you sign.

SystemWhat actually happens in a relocationWho may do it
Gas pipingNew pipe run to the new wall, resized for the longer length and the total appliance load, with a new shutoff and a sediment trap at the appliance.Licensed gas fitter only
Venting and terminationIndoor units get a new vent route and a new termination in a compliant spot. Outdoor units vent through their own outlet, which creates its own clearance zone.Licensed gas fitter only
Combustion airConfirmed for the new arrangement. Sealed combustion units take air through a dedicated intake; room-air units depend on the volume and openings of the new space.Licensed gas fitter only
Electrical and bondingA supply to the new location, a disconnect, and bonding of gas and water piping. Freeze protection on an outdoor unit depends on this circuit staying live.Licensed electrician
CondensateNew drain line on a condensing unit, run at the required slope in approved material, neutralised where required, with a pump where gravity will not work.Licensed technician
Water pipingNew hot and cold runs tying back to existing distribution, with insulation on exposed sections and isolation valves for future service.Licensed technician
RecirculationIf a return line, an external pump or a crossover valve exists, it moves or is redesigned around the new location.Licensed technician
Old locationGas capped, vent opening sealed and made weathertight, penetrations patched, and the space made ready for finishing.Licensed technician plus finishing trades
Permit and inspectionApplication filed, work left accessible for inspection, and the file closed out with the authority having jurisdiction.Licensed contractor

Will an outdoor tankless water heater survive a Metro Vancouver winter?

Generally yes, and that is exactly why outdoor installations are common on the coast. Our winters are mild and wet rather than deeply cold, and outdoor-listed units are designed for this kind of climate. The important detail is how they survive it: outdoor tankless units have built-in freeze protection, usually a small electric heating element inside the cabinet, and that protection only works while the unit has power. Kill the circuit at the panel over a holiday, or lose power during a windstorm while the temperature sits below freezing, and the appliance is on its own.

That turns two things into safety items. The first is the electrical supply, which should not share a circuit with anything a homeowner might switch off casually. The second is the piping outside the cabinet, because the unit’s internal freeze protection does not protect the water lines running up the wall to it. Those get insulated and, depending on exposure, may need additional measures. A hard freeze during a Fraser Valley outflow event is the scenario to design for, not a typical January.

The other winter consideration is the exhaust. A gas tankless unit outdoors still produces combustion products, and its outlet has a required clearance zone around it that must stay clear of openable windows, doors, intakes and walking paths. In dense Metro Vancouver lots, especially where a house sits close to a neighbouring wall or a side-yard walkway, finding a compliant termination is sometimes the hardest single constraint in the whole job.

What does relocating a tankless water heater cost in Metro Vancouver?

A straightforward tankless installation in Greater Vancouver, supply and labour, sits in a ballpark range of roughly $3,900 to $7,800 installed before GST. These are ballpark figures for orientation only. They are not a quote, and an accurate price for your home requires a site visit, because the relocation variables below move the number more than the appliance does.

The relocation-specific work sits on top of that. Running a new gas line to an appliance is a ballpark range of about $500 to $1,500 where the run is short and the route is accessible, and about $1,500 to $3,000 or more where the run is long, crosses finished space, or needs the whole branch resized. If you are converting from a tank at the same time as moving the location, the tank-to-tankless conversion ballpark range is roughly $4,500 to $8,000 and up, again before GST, because that job carries the gas, vent, electrical and condensate work as well.

None of those ranges include permit fees, which are set by each municipality or by Technical Safety BC and vary by jurisdiction. We do not attach dollar figures to rebates or incentive programs, to financing, or to a diagnostic visit; those are discussed separately and qualitatively, because the numbers depend on program rules and on your specific situation rather than on the mechanical work.

  • Gas line length and sizing. The single biggest variable. A short run in an open basement is a different job from resizing a branch that also feeds a furnace and a fireplace.
  • Venting and termination. An outdoor unit avoids a vent run but creates a clearance problem. An indoor relocation trades that for metres of vent material and penetrations.
  • Electrical. A spare panel position and a short run is minor. A full panel, a long run, or a panel upgrade is not.
  • Condensate. A floor drain nearby is easy. A condensate pump, neutraliser and a long drain line across a finished ceiling is not.
  • Access and finishes. Opening and repairing drywall, working in a crawlspace, or getting the unit through a tight suite entrance all add labour.
  • Code upgrades triggered by the work. Bonding, shutoffs, seismic or support details and combustion air corrections are commonly brought up to current requirements during the permit.
  • Disposal of the old appliance and the materials that came out with it.

How long is the household without hot water?

For a typical single-family relocation with reasonable access, plan on the hot water being off for most of one working day and, on more involved jobs, into a second. A relocation is not a same-day job the way a like-for-like tank swap sometimes is, and we will say that plainly rather than promise an arrival and finish window we cannot control.

The sequence is usually: shut down and drain the existing unit, remove it, rough in the new gas, vent, electrical and condensate at the new wall, mount and connect the appliance, then tie the water piping back in. Water is off for the tie-in portions rather than the entire day. Heating is only affected if the appliance also serves a combination heating function, which is a separate conversation with its own scope.

The inspection is the part that stretches the calendar rather than the disruption. Work has to stay accessible until the inspector has seen it, which means drywall, ceiling patching and any finishing carpentry in the old closet waits. If you are finishing a basement around this work, sequence the mechanical relocation and its inspection before the finishing trades, not after.

What makes Metro Vancouver housing stock harder or easier for this job?

Our housing stock is the real story here. Older Burnaby, East Vancouver, New Westminster and North Shore homes were often piped decades ago for a much smaller gas load, and that undersized branch is the number one reason a relocation costs more than the homeowner expected. Add a suite with its own appliances and the branch sizing question becomes unavoidable.

Lot density is the second constraint. On narrow lots, laneway-house properties and side-by-side duplexes, the exterior wall that makes sense from inside the house is often the wall facing a neighbour, a walkway or an openable window, and the clearance requirements around a combustion appliance’s exhaust do not bend for convenience. We have walked plenty of jobs where the mechanically obvious wall was the one wall we could not use.

Strata and townhouse properties add an approval layer. Anything that penetrates an exterior wall or changes the look of the building envelope usually needs written strata approval before work starts, and the strata may have its own requirements about who does the work and what insurance they carry. Start that conversation early, because it takes longer than the mechanical work does.

One piece of good news: our incoming water is cold but soft. That means the descaling conversation for tankless units here is about heat-driven mineral deposits and debris rather than the aggressive limescale you would fight in a hard-water region. It is still real maintenance and the unit still needs isolation valves so it can be flushed, but it should not be the thing that drives your decision. Cold incoming water does affect how the appliance performs in winter, which is a sizing conversation for your specific model and household, using manufacturer-published figures that we verify rather than quote from memory.

Is moving it worth it, or should I wait and do it during the replacement?

Here is the honest framing. The labour to relocate an existing tankless unit and the labour to install a new one in a new location are nearly the same, because both jobs require all of the gas, vent, electrical and condensate work. The only difference is the appliance itself. So if your unit is well into its service life, paying relocation labour to move it is often poor value: you spend the money, and then a few years later you pay a technician to disconnect and reconnect at the new wall all over again.

Cases where relocating now clearly makes sense: the appliance is relatively new, you are finishing a basement or adding a suite and the wall has to be clear, the current location is genuinely unsuitable, or a noise or access problem is making the household miserable. Cases where we will tell you to wait: the unit is aging, the relocation is cosmetic, or the new wall creates a termination problem that would be solved by choosing a different appliance configuration.

And occasionally the answer is that this one is not worth moving at all. If the unit is an indoor model with no manufacturer-published outdoor conversion, if the gas branch needs a full resize plus a meter conversation, and if the only compliant exterior termination is on the far side of the house, you are buying a very expensive way to keep an old appliance. In that situation we will lay out the replacement option beside the relocation option and let you compare complete scopes rather than steer you.

When should I call a licensed technician?

For a relocation, from the beginning. Gas work in British Columbia is restricted to licensed gas fitters and most electrical work to licensed electricians, and a permitted relocation has to be performed and closed out by licensed trades. There is no homeowner-legal version of moving a gas appliance.

What a homeowner can reasonably do: decide where the appliance should live, clear the route and the work area, remove storage and finishes from the old closet, handle the strata application, arrange access, and keep the new area clear afterwards so the unit can be serviced. Homeowners can also do the ongoing surface-level maintenance a manufacturer permits, such as cleaning an accessible inlet filter screen, if the manual says so and the unit is shut down first.

Call a licensed technician immediately, rather than scheduling, if you smell gas, if a CO alarm sounds, if the appliance is producing soot or unusual smells, if there is water where there should not be, or if an outdoor unit has lost power during freezing weather. Emergency situations are handled differently from planned work, and we will tell you honestly whether same-day attendance is possible on a given day rather than promise a window we cannot hold.

Gas & carbon-monoxide safety: Gas and carbon monoxide safety come before anything else on this job. If you smell gas, do not operate switches or appliances: leave the building, take everyone with you, and call from outside. Working carbon monoxide alarms belong on every level of the home, including outside sleeping areas, and they matter just as much when the appliance moves outdoors, because the failure modes that matter are vent terminations too close to windows and intakes. Combustion air and vent termination location are safety requirements, not preferences, and they come from the code and from the manufacturer’s installation instructions for your exact model. Never modify gas piping, venting, combustion-air openings or electrical connections yourself; in British Columbia this work is restricted to licensed trades and must be permitted and inspected. If an outdoor unit loses power during freezing weather, treat it as urgent rather than routine, because its freeze protection stops working when the circuit is dead.

Frequently asked questions

Can my indoor tankless water heater be installed outside?

Only if the manufacturer publishes an outdoor conversion for that exact model, or if the unit is already an outdoor-listed version. Some families, such as Bradford White’s Infiniti K Series, are built in both indoor and outdoor versions, and Rheem publishes a conversion kit for certain indoor models. A technician confirms this against the installation instructions for your unit before anything else is planned.

Does moving a tankless water heater need a permit in BC?

Yes. Relocating a gas appliance means new gas piping and new venting, which requires a permit and an inspection through the authority having jurisdiction, and the work must be done by licensed trades. Permit fees are set by each municipality or by Technical Safety BC. Leave the work accessible until the inspector has signed off, before any drywall or finishing goes back.

Will an outdoor tankless unit freeze in winter here?

Outdoor-listed units have built-in freeze protection designed for climates like ours, but it is electric and only works while the unit has power. The water piping running up the wall to the unit is outside that protection and needs insulation and, depending on exposure, additional measures. Do not switch off the appliance’s circuit when you leave the house in winter.

How much does it cost to relocate a tankless water heater?

A tankless installation in Greater Vancouver sits in a ballpark range of about $3,900 to $7,800 installed before GST, with the relocation-specific gas line work adding roughly $500 to $1,500 for a short accessible run or $1,500 to $3,000 and up for a long or difficult one. Those are ballpark ranges for orientation, not a quote. Gas line sizing, vent termination, electrical and condensate routing move the number far more than the appliance choice does.

How long will we be without hot water?

Plan on most of one working day for a typical single-family relocation with reasonable access, and into a second day on more involved jobs. Water is fully off only during the tie-in stages, not the whole day. The inspection, not the disruption, is what usually stretches the calendar, so schedule the mechanical work before any finishing trades.

What should be written on the quote for a relocation?

A complete scope names the gas line work and its sizing, the vent route and termination, combustion air, the electrical supply and bonding, condensate routing and any pump or neutraliser, the water piping tie-in and insulation, what happens to the old location, disposal, and the permit and inspection. If one of those is missing from the written scope, ask who is doing it. An incomplete quote is usually not a cheaper job, just a job priced before its hardest parts were counted.

Should I just replace the unit instead of moving it?

Often, yes. The gas, vent, electrical and condensate labour is nearly identical whether you move the existing appliance or install a new one at the new wall, so the only saving from relocating is the appliance itself. If your unit is well into its service life, moving it means paying that labour twice within a few years. If it is relatively new and in good shape, relocating is reasonable.

Does moving it affect recirculation and hot water wait times?

It can, and it is worth planning for. A built-in recirculation pump, an external pump on a dedicated return line and a crossover or bypass-valve retrofit are three different systems with different piping needs, and moving the appliance changes the distances involved. Some Bradford White Infiniti models and Rheem IKONIC SR units include a pump while their companion models do not, so confirm what your unit has before assuming the existing arrangement transfers. Discuss wait times at the fixtures during the site visit rather than after the appliance is mounted.

Related services & guides

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How long does a hot water tank last?
A standard gas or electric storage tank lasts 8–12 years. A high-quality tank with annual anode rod inspection can reach 15 years. Tankless water heaters typically last 18–22 years when descaled annually in Metro Vancouver's moderately hard water.
Should I switch to a tankless water heater?
Tankless makes sense if you have high demand (large family, multiple bathrooms running at once), want to free up floor space, or value endless hot water. Upfront cost is higher ($3,500–$6,000 installed vs $1,800–$3,200 for a tank) but operating cost is 25–40% lower for gas tankless.
My hot water tank is leaking — is it an emergency?
If the leak is from the tank body itself (not a valve or fitting), the tank is at end of life and needs replacement, usually within 24–48 hours before it floods. Shut off the water supply and gas/electric to the tank and call us.
What brands of water heaters do you install?
We install and service Bradford White, Rheem, AO Smith, John Wood, Giant, GSW for storage tanks; and Navien, Rinnai, Noritz, Bosch and Rheem for tankless units.
Can I install a water heater myself?
In BC, gas water heater installations must be performed by a TSBC-licensed gas fitter and are subject to permit and inspection. Electric tanks require a licensed electrician for the connection. BC Wide handles permits as part of every installation.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote