★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Triangle Tube Prestige Excellence Combi Boiler Installation and Replacement

Boilers

Triangle Tube Prestige Excellence Combi Boiler Installation and Replacement
Home › Triangle Tube Prestige Excellence Combi Boiler Installation and Replacement

Triangle Tube Prestige Excellence Combi Boiler Installation and Replacement

Key takeaways

  • The Prestige Excellence family pairs a condensing heating boiler with built-in domestic hot water storage, so the install covers two systems at once: the heating loop and the household hot water.
  • Sizing comes from a room-by-room heat-loss calculation plus a hot-water demand assessment, never from copying the rating of the boiler being removed.
  • Venting, condensate disposal and gas-line capacity are the three things most likely to change the scope of the job in an older Metro Vancouver house.
  • All gas, venting and electrical connections must be done by licensed trades, under a gas permit, and the job is not finished until the combustion analysis is done and recorded.
  • In Metro Vancouver’s soft water, the old heating loop’s sludge and corrosion debris is the biggest threat to a new condensing heat exchanger, so flushing and filtration belong in the quote.
  • At handover you should receive the permit number, the combustion readings, the control settings and the manufacturer’s registration details in writing.

Installing a Triangle Tube Prestige Excellence combi boiler properly means sizing it to your home’s actual heat loss and hot-water demand, running a sealed condensing vent and a neutralized condensate drain, confirming the gas line can carry the new load, cleaning and protecting the existing heating loop, connecting both the hydronic circuit and the domestic hot-water piping, and then commissioning the unit with a combustion analyzer under a gas permit. In a Metro Vancouver home that usually means replacing an older atmospheric or early high-efficiency boiler, and the replacement is where most of the real work sits: new venting, a new condensate route, often a gas-line upgrade, and a thorough flush of a loop that has been collecting sludge for decades. BC Wide Home Services is an independent, TSBC-licensed gas contractor (LGA0090068, CGA0028029) that installs and services this family. We are not a factory-authorized dealer or warranty centre, and the manufacturer’s installation manual for your exact unit governs every clearance, vent length and piping detail described below.

What makes the Prestige Excellence different from other combi boilers?

Most combi boilers heat domestic water on demand through a plate heat exchanger, the same way a tankless water heater does. The Prestige Excellence family is commonly documented as taking a different approach: a condensing heating boiler combined with built-in domestic hot water storage, so a reserve of hot water is already heated when someone opens a tap. Confirm the exact configuration of your unit on the rating plate and in the installation manual, because it drives how the job is piped.

For the installer, that design changes three things. First, the unit is heavier and larger than a wall-hung on-demand combi, so floor space, access and the path into the mechanical room all need checking at the survey. Second, the domestic side has storage, which brings a temperature and pressure relief valve discharge, thermal expansion control on the cold supply and a mixing valve to limit scald risk at the taps. Third, the controls have to prioritize hot water over space heating in a way that suits your household, and those settings get chosen at commissioning rather than left at factory defaults.

How do you size a Prestige Excellence for my house?

Sizing is two separate calculations. The heating side comes from a room-by-room heat-loss calculation that accounts for wall and ceiling insulation, window area and type, air leakage and the design outdoor temperature for your municipality. The hot-water side comes from how many bathrooms you have, whether there is a soaker tub, how many people shower back to back in the morning, and whether anyone is moving in or out of the house soon.

The rating on the old boiler is not a sizing method. Many older Lower Mainland homes were fitted with boilers far larger than the house ever needed, and the envelope has often been improved since with new windows or attic insulation. An oversized condensing boiler short-cycles, spends less time in the low-return-temperature range where condensing actually happens, and wears its igniter and controls faster. Undersizing is also a real risk on the hot-water side, because a family that drains the storage every morning will notice. Each model in the family has manufacturer-published input and hot-water ratings; we match those to the load numbers and show you the calculation in writing.

What happens at the site survey before the quote?

A proper written quote for this family cannot be produced from a phone call or a photo of the old boiler. The survey is where the real scope is found, and it is where most of the difference between two quotes comes from.

  • Heat-loss measurements: room dimensions, window counts, insulation where it can be seen, and the type of emitters (baseboard convectors, cast-iron radiators, in-floor radiant or a mix).
  • Existing loop condition: the colour and clarity of water drawn from a drain valve, signs of rust or black sludge, and whether the loop has ever been treated or flushed.
  • Venting route: where a sealed concentric or two-pipe vent can terminate, measured against clearances to windows, doors, air intakes, gas meters, soffits and property lines under the gas code and the manual.
  • Old chimney: whether the existing masonry or metal chimney will be orphaning another appliance, such as a gas water heater, that needs its own venting plan once the boiler leaves.
  • Gas supply: meter size, pipe sizes and lengths back to the meter, and every other gas appliance on the same line, so the capacity check can be done properly.
  • Condensate: a floor drain, standpipe or condensate pump location, and where a neutralizer can sit.
  • Electrical: a dedicated circuit and a service switch within reach of the unit, plus the location and wiring of every thermostat and zone control.
  • Access: the path to the mechanical room, stair turns, and whether the unit and its storage can be moved in without removing doors or finishes.

What is the installation sequence, step by step?

A typical replacement runs over one to several working days depending on how much venting, gas and loop work the survey uncovered. The sequence below is how we run it, and the right-hand column is the honest answer to who is allowed to do each step in BC.

StageWhat happensWho may do it
PermitGas permit pulled before work starts; electrical permit where new circuits are runLicensed gas contractor; licensed electrical contractor
Shut-down and removalGas isolated and capped, old boiler drained, disconnected and removed, old vent assessedLicensed gas fitter
Loop cleaningExisting heating loop flushed with a cleaner suited to the metals in the system, then rinsedInstaller; homeowner cannot open the sealed system
Setting the unitUnit placed level on a suitable base with service clearances from the manualInstaller
Hydronic pipingPrimary-secondary or manufacturer-approved piping, circulators, air separator, expansion tank, dirt separator or magnetic filter, isolation valvesInstaller
Domestic hot-water pipingCold supply with backflow and expansion control, hot outlet through a mixing valve, relief valve discharge piped to a safe locationInstaller
VentingSealed intake and exhaust in the materials the manual lists, sloped back to the unit, terminated at code clearancesLicensed gas fitter
Gas connectionNew or upsized gas line as needed, sediment trap, shut-off valve, leak testLicensed gas fitter only
CondensateTrap, neutralizer and drain or condensate pumpInstaller
Electrical and controlsService switch, thermostats, zone controls, outdoor sensorLicensed trades for line-voltage work
CommissioningFill and purge, combustion analysis at high and low fire, safety checks, control setupLicensed gas fitter
Inspection and handoverGas inspection as required by the permit, paperwork and owner walkthroughInspector and installer

How are venting, condensate and the gas line handled on this family?

Venting is where a condensing replacement most often changes the job. The old atmospheric boiler vented hot, buoyant exhaust up a chimney. The Prestige Excellence vents cool, wet exhaust under pressure through sealed pipe, usually out a side wall or up through the old chimney as a chase if the manual permits that approach. Maximum and minimum vent lengths, approved materials and termination kits are manufacturer-published, so check the installation manual for your exact unit. Exhaust plume location matters too: on a narrow Vancouver or Burnaby lot, a sidewall termination facing a neighbour’s window a few metres away can be legal and still be a problem, so we plan it with you.

Condensate is acidic. It runs through a trap and a neutralizer before it reaches a floor drain or a condensate pump, and the neutralizer media needs periodic replacement. In a basement without a nearby floor drain, the pump and its discharge route get added to the scope.

Gas supply is the quiet blocker in older housing. A combi carries both the heating load and the domestic hot-water load, and when it fires at full input alongside a gas range, fireplace or dryer, an undersized line can starve the burner and cause poor combustion or lockouts. We calculate pipe capacity from the meter to every appliance. If the line is short, the fix may be a larger branch, a new run, or a conversation with the gas utility about the meter, and all of that is written into the quote before work starts.

Should I repair my current boiler or replace it with a Prestige Excellence?

The decision usually comes down to four things: the age and condition of the heat exchanger, whether parts are still available, how much the venting has deteriorated, and whether you also need to replace a separate water heater. A leaking or cracked heat exchanger on an older boiler is usually the end of that appliance, because the part is one of the most expensive in the system and often is no longer made. A failed igniter, circulator or pressure switch on a boiler that is otherwise sound is normally worth repairing.

Replacement with a combi makes the most sense when the boiler and a separate gas water heater are both near the end of their service life, because one appliance and one vent replace two. It makes less sense when the existing loop is badly sludged and the owner is not prepared to have it cleaned, since a new condensing heat exchanger will not tolerate the debris an old cast-iron boiler shrugged off. We give you a written quote for the repair and a separate written quote for the replacement so you can compare them side by side, and we tell you plainly which we would choose in your house.

What about Metro Vancouver homes specifically?

Our water is soft, which is good news for the domestic side of this family: heavy limescale is not the usual problem here. On the heating side, soft water tends to be more aggressive toward steel and iron, and older loops in Burnaby, East Vancouver, New Westminster and North Vancouver commonly carry black iron-oxide sludge and rust. That debris is what blocks condensing heat exchangers and wears out circulators, so a chemical flush, a magnetic dirt separator and an inhibitor at the right concentration belong in any quote for this family.

Our mild, wet coastal winters mean the boiler spends most of the season at low firing rates. That favours condensing operation, but only if outdoor reset is set up so the supply water temperature drops on mild days. Many older radiator systems were designed around very hot water, and the commissioning visit is where we find the lowest temperature that still keeps every room comfortable.

Housing stock also shapes the job. Character homes often have tight basements, old chimneys shared with a water heater and gas lines sized decades ago. Townhouses and strata units may restrict where a vent can terminate on an exterior wall; we do not interpret strata bylaws, so the owner confirms what is allowed with council before a vent route is finalized. For heritage-designated houses, exterior termination questions go to the municipality. Permits are issued by Technical Safety BC in most Lower Mainland municipalities, while the City of Vancouver issues gas permits within its own boundaries.

What should I receive in writing at the end of the job?

A correct install is documented, and the paperwork is what protects you at the next service visit, at resale and with the manufacturer’s warranty process. You should not have to ask for any of this.

  • The gas permit number and confirmation that the required inspection was completed or booked.
  • The combustion analysis readings at high and low fire, taken with a calibrated analyzer, including carbon monoxide in the flue gas.
  • The heat-loss and hot-water sizing summary used to select the unit.
  • Control settings as left: heating and domestic hot-water temperatures, outdoor reset curve, priority settings and zone setup.
  • Loop treatment record: what cleaner and inhibitor were used and the measured concentration.
  • Model and serial numbers from the rating plate, with the manufacturer’s product registration completed or instructions to complete it.
  • The installation manual and user manual left with the unit, and a recommended annual maintenance schedule.

When should I call a licensed technician, and what can I do myself?

Homeowners can safely read the display, check the system pressure gauge against the level the installer marked, reset a thermostat, and watch that the condensate is draining and the vent terminal is clear of snow, leaves or ice. Anything that involves opening the sealed combustion chamber, adjusting gas pressure or combustion, working on the vent, touching line-voltage wiring, or opening the relief valve discharge is licensed work in BC.

Call us at (604) 473-9690 if the unit locks out repeatedly, if system pressure keeps dropping and needs topping up, if the relief valve discharges, if you see water or rust at the base, if hot water runs out much sooner than it used to, or if you hear kettling or banging in the heat exchanger. We offer same-day service where our schedule allows, but we will not promise an arrival window we cannot keep, and a no-heat call on a cold night is triaged ahead of routine work.

Gas & carbon-monoxide safety: The Prestige Excellence is a gas-fired appliance, and every gas, venting and combustion step on it is licensed work in BC. Keep working carbon monoxide alarms on every level of the home and outside sleeping areas, and replace them on the maker’s schedule. If you smell gas, do not operate switches, phones or appliances inside; leave the house, then call FortisBC and a licensed gas contractor from outside. If a CO alarm sounds or anyone has headaches, dizziness or nausea that ease when they leave the house, get everyone outside and call 911. Never use a gas oven, range, barbecue or patio heater indoors for warmth while waiting for a repair.

Frequently asked questions

Can a Prestige Excellence use my existing chimney?

Not as a standard chimney, because a condensing boiler produces cool, wet, pressurized exhaust that an old masonry flue cannot handle. Some installations run the sealed vent pipe up through the old chimney as a chase where the manual permits it. We confirm the approved vent materials and routes in the installation manual for your exact unit at the survey.

Do I need a permit to replace my boiler with a combi?

Yes. Boiler replacement is gas work that requires a gas permit, pulled by a licensed gas contractor, and the installation is subject to inspection. In most Lower Mainland municipalities the permit comes from Technical Safety BC, and in the City of Vancouver it comes from the city.

Will the Prestige Excellence work with my old cast-iron radiators?

Usually, yes, provided the loop is cleaned first and the controls are set up properly. Cast-iron radiators hold a lot of water and often run well at lower supply temperatures than they were originally designed for, which suits condensing operation. The commissioning visit is where we set the outdoor reset curve to find that balance.

How long does a Prestige Excellence installation take?

A straightforward replacement with a clean loop and an easy vent route is typically a short multi-day job. New gas lines, a long vent run, a condensate pump or a heavily sludged loop add time. The written quote lists the expected duration and what could extend it.

Is BC Wide a Triangle Tube dealer?

No. BC Wide Home Services is an independent TSBC-licensed gas contractor that installs and services the Triangle Tube Prestige Excellence family, along with other boiler brands. We are not a factory-authorized dealer or warranty centre, and we point you to the manufacturer’s own registration process for warranty coverage.

Does soft Metro Vancouver water mean I can skip water treatment?

No. Soft water means less limescale, but it tends to be more corrosive to the steel and iron in older heating loops, which is where sludge comes from. A flush, a dirt separator and a correctly dosed inhibitor protect the new heat exchanger regardless of how soft the water is.

How do I get a quote for a Prestige Excellence installation?

Call (604) 473-9690 to book a site survey. We measure the house, inspect the loop, venting, gas supply and condensate options, and give you a written quote with the scope spelled out. No work starts until you have approved that quote.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote