★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Viessmann Boiler Code 18 — Outdoor temperature sensor open circuit | BC Wide

Boilers, Error Codes, Hvac

Viessmann Boiler Code 18 — Outdoor temperature sensor open circuit | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Viessmann Boiler Code 18 — Outdoor temperature sensor open circuit | BC Wide

Viessmann Boiler Code 18 — Outdoor temperature sensor open circuit | BC Wide

Quick answer

Viessmann boiler error code 18 means the boiler has lost the signal from its outdoor temperature sensor: the sensor lead is broken or the circuit is open (confirm against the manual for your unit). Heating usually continues at a default curve, so the house stays warm, but the boiler stops adjusting its water temperature to the weather. From outside, check that the sensor is still on the wall and its cable is not visibly cut, then book a licensed technician at (604) 473-9690.

If your Viessmann boiler is showing 18 (Outdoor temperature sensor open circuit), here’s exactly what it means and what to do. This guide is part of our full Viessmann boiler error code list.

Severity: Needs attention.

What 18 means on a Viessmann boiler

The outdoor temperature sensor lead is broken / open circuit.

Common causes

  • Broken sensor cable
  • Disconnected outdoor sensor
  • Faulty sensor

What you can safely check first

  1. Heating usually continues at a default curve
  2. Book an engineer to check the sensor wiring

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Viessmann boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Viessmann boiler repair across Greater Vancouver

If a Viessmann boiler showing 18 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Viessmann boiler codes

Frequently asked questions

Is 18 on a Viessmann boiler serious?

It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs Viessmann boilers 7 days a week across Greater Vancouver.

How do I reset a Viessmann boiler after 18?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Viessmann Boiler Error Code 18: what it means for your heat and hot water

In plain terms, code 18 tells you the boiler can no longer read the temperature outside. The outdoor sensor is a small weatherproof probe fixed to an exterior wall, usually on a shaded side of the house, and it is joined to the boiler by a thin low-voltage cable. The boiler uses that reading to run what installers call outdoor reset: on a mild, damp Vancouver day it sends cooler water to the radiators or in-floor loops, and as the weather turns colder it raises the water temperature to match. When the cable breaks, a wire pulls out of a terminal or the probe itself fails, the circuit opens, the control sees a reading that cannot be real, and it flags code 18 instead of guessing. Confirm the exact wording of the code against the manual for your unit.

What you notice depends on the season and how your system is set up. As noted above, heating usually continues at a default curve, which means the boiler falls back to a fixed water temperature rather than following the weather. That fallback is a compromise. On a cold, clear night the house can feel slow to recover after the thermostat setback ends, and in spring or fall some rooms can run warmer than you want while the boiler fires and stops more often than it should. Control generations behave differently, so check the fallback behaviour for your model in the manual rather than relying on a general description.

Domestic hot water is a separate question. Where the boiler heats an indirect storage tank, the tank is normally controlled by its own sensor, so hot water often carries on as usual with code 18 on the display. If you lose hot water at the same time as code 18 appears, treat that as a second problem, not a symptom of the outdoor sensor, and tell the technician when you book.

It also helps to know what code 18 is not. It is not a flame failure, an ignition fault or a gas-supply problem in itself, and on its own it is not a sign of carbon monoxide. It is a sensing fault. It still matters, because a condensing boiler only condenses well when the water coming back to it is cool, and outdoor reset is the main way it keeps that water cool on the many mild days of a coastal winter. Running on a fixed curve for months usually means more cycling, more wear and a higher gas bill than the boiler was designed to deliver.

  • The display shows 18 or a fault symbol with 18, while the radiators or floors still warm up.
  • Rooms feel hotter than usual on a mild day, or slower to warm up on a cold one.
  • The boiler fires and shuts off more often than it used to.
  • Gas use looks high for the weather compared with past winters.
  • The code appeared right after exterior work such as painting, new siding, a deck, gutter work, pressure washing or landscaping.
  • The code comes and goes in heavy rain or wind, which usually points to a loose or wet connection.

Viessmann boiler error code 18 causes, most common first, and the checks you can safely make

These are the causes we find on Metro Vancouver homes, roughly in the order we find them. The short list higher up the page names a broken cable, a disconnected sensor and a faulty sensor; here is what each looks like on site and where your part stops and a licensed technician’s part begins.

Owner-safe checks, in order: confirm the boiler has power and its service switch is on; confirm the gas supply valve to the boiler is open, with the handle in line with the pipe; confirm a thermostat is actually calling for heat; walk outside and look at the outdoor sensor and the visible part of its cable without opening anything; check that the boiler’s intake and exhaust terminals outside are clear of leaves, nests, snow or stored items; and look at the visible condensate drain line for a kink or blockage. If your owner manual allows a reset, press it once only. If code 18 returns, stop there and book the visit. Do not open the boiler casing, the control housing or the sensor cover, and never bridge, jumper or bypass any terminal to clear the code.

  • 1. Cable cut or crushed during outside work. Painters, siding crews, deck builders and landscapers often staple over, cut or bury the thin sensor cable without knowing what it is. This is the single most common cause we see.
  • 2. Sensor knocked off the wall or disconnected. A ladder, a gutter crew or a fence rebuild can pull the probe off its mount and leave it hanging by the wire, or pull the wire out of it.
  • 3. Corroded or wet connection at the sensor. Our long wet season works its way into a cover that was not sealed properly, and green corrosion on the terminals eventually opens the circuit. This is the cause that tends to come and go with the rain.
  • 4. The sensor itself has failed. Sensors are simple parts, but they do age, and one that has sat in direct sun and rain for many years can drift and then fail open.
  • 5. Loose terminal or damaged cable indoors. Renovations in a basement or mechanical room, rodents, or a cable run pinched behind drywall can break the circuit inside the house.
  • 6. Less often, a fault at the control’s sensor input. We only reach this conclusion after the sensor and the whole cable run have tested good, and it is confirmed with meter readings, not guessed.
Likely causeWhat you can safely checkWhen it becomes a licensed call
Cable cut or crushed during exterior workLook along the visible cable outside for staples, cuts or fresh paint over itAny splice or new cable run, because the cable connects into the boiler control
Sensor knocked off or disconnectedSee whether the probe is still mounted and the wire still enters itRe-mounting and reconnecting, which means opening the sensor cover and the control terminals
Corroded or wet sensor connectionNotice whether the code appears mainly in heavy rainCleaning, sealing or replacing the connection and confirming the reading with a meter
Failed outdoor sensorNothing beyond the visual check; a sensor can look perfect and still be openTesting the sensor against the manufacturer’s published values and replacing it
Loose terminal or damaged cable indoorsNote any recent renovation, drywall or pest activity near the boilerOpening the control housing, tracing the cable and re-terminating it
Control sensor input faultNone; this is never an owner checkConfirmed only after the sensor and cable test good, then quoted in writing

Is it safe to run a Viessmann boiler with error code 18, and when is it a licensed call?

In most cases the boiler can keep heating safely on its default curve while you wait for a technician, because code 18 is a sensing fault rather than a combustion fault. The honest qualifier is that code 18 tells you about one input only. It says nothing about the burner, the venting or the heat exchanger, and a boiler can have two problems at once. If anything else seems wrong at the same time, do not assume it is part of the same fault.

Gas and carbon monoxide safety comes first with any gas boiler. If you smell gas, or a carbon monoxide alarm sounds, do not touch light switches or the boiler controls. Get everyone out of the house, then call FortisBC or 911 from outside. Every home with a gas boiler should have working carbon monoxide alarms near sleeping areas and in the area of the boiler, and the outside intake and exhaust terminals must stay clear so the boiler can breathe and vent properly. A blocked vent can cause lockouts and, in the worst case, combustion problems, which is why clearing leaves or snow away from the terminal is on the owner-safe list and nothing more invasive is.

In BC, gas work is restricted to licensed gas fitters working under Technical Safety BC, and the boiler’s control and sensor wiring should be handled by a qualified technician. A homeowner may look, confirm power and gas valve position, check the thermostat, clear the outside terminals and press reset once if the manual allows. Everything inside the casing, every terminal, every splice and every part replacement is a technician’s job.

  • Call a licensed technician if code 18 returns after one reset, or never cleared at all.
  • Call if the house is not keeping up with the thermostat on a cold night.
  • Call if the boiler is short cycling, making new noises, or showing other codes alongside 18.
  • Call if you see water around the boiler, a dropping pressure reading, or a wet or blocked condensate line.
  • Leave and call FortisBC or 911 from outside if you smell gas or a carbon monoxide alarm sounds.

How our Viessmann boiler error code 18 repair visit works

Diagnostic service calls are $189.00. That covers a licensed technician coming to the house, finding the actual fault with the right test equipment and explaining it to you before anything else happens. We book same-day where we can, which depends on the day’s calls and how far across Metro Vancouver the job is, and we never promise a guaranteed arrival window. When you call, tell us the code, whether you still have heat and hot water, and whether any outside work was done recently; that last detail often shortens the visit.

The parts most often involved with code 18 are, in general terms, the outdoor sensor itself, a length of sensor cable, and the connector or terminal at either end. Far less often the fault is at the control’s input. We tell you which one it is and show you the reading that proves it, and nothing beyond the diagnosis is done until you have a written quote and have said yes.

What a correct job looks like when we leave: the outdoor sensor is mounted firmly on a shaded wall away from dryer vents, windows and the boiler exhaust, so it reads the real outside air; the cable is supported, protected where it passes through the wall and sealed against rain; the connections are clean and tight; the boiler reports a believable outdoor temperature; and the heating curve is set so the water temperature actually follows the weather. What you should see in writing: the fault found, the readings taken, the parts replaced, the safety tests done and their results.

  • Step 1: We read the fault history on the boiler display, note when code 18 first appeared and check for any other stored codes.
  • Step 2: We inspect the outdoor sensor and the whole visible cable run outside, including where it enters the building.
  • Step 3: With a meter, we test the sensor against the manufacturer’s published values and test the cable for continuity, so we know whether the sensor, the cable or a connection is open.
  • Step 4: We confirm the control’s sensor input only after the sensor and cable are proven, so you never pay for a control part you did not need.
  • Step 5: You get a written quote for the repair before any work beyond diagnosis begins.
  • Step 6: Once approved, we repair or replace the sensor, cable or connection, seal it against the weather and re-check the reading.
  • Step 7: We test the boiler’s safeties and operation: a full heat call, combustion checked with an analyzer, venting and terminals inspected, the condensate trap and drain checked, system pressure confirmed and carbon monoxide checked at the appliance.
  • Step 8: We set or confirm the outdoor reset curve with you, so the house is comfortable on both mild and cold days, and leave the written record of what was found and done.

Repair or replace an older Viessmann boiler showing code 18?

Code 18 on its own is almost never a reason to replace a boiler. An outdoor sensor and its cable are among the simpler, less expensive repairs on a modern condensing boiler, well below the cost of a burner part or a control module. For the large majority of homes the right answer is to fix the sensor circuit properly and get the boiler back on its outdoor reset curve.

The visit is, however, a good moment to look at the whole system, especially on a boiler that has been in service a long time. Metro Vancouver water is soft, so the hydronic problems we see here are sludge and corrosion rather than limescale. Black magnetite sludge in the loops, a strainer that keeps clogging, or corrosion around fittings can shorten a heat exchanger’s life and make a boiler short cycle no matter how well its sensors work. Parts availability for older control generations is the other factor: when a control part is hard to source, the conversation changes.

If replacement is worth considering, we will say so and explain why in writing. The in-home estimate for replacing or installing a boiler is free, and if you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation. If the boiler is still under a manufacturer warranty, check the terms with the original installer or the manufacturer before any part is replaced; we are an independent contractor, not a warranty centre.

  • Repair makes sense when code 18 is the only fault and the boiler otherwise runs, vents and burns cleanly.
  • Look harder at replacement when the boiler also has repeated lockouts, a leaking or badly corroded heat exchanger, or heavy sludge that keeps coming back.
  • Look harder at replacement when a needed control part is no longer readily available for that generation of boiler.
  • Either way, ask for the reasons in writing, with the readings and photos that support them.

Viessmann boiler error code 18 service near you in Greater Vancouver

We repair code 18 and other outdoor sensor faults across Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the rest of the Tri-Cities, the North Shore, New Westminster, Delta and Langley. Housing stock varies a lot across that area, and it shapes the job. Older Vancouver, Burnaby and New Westminster houses often have boilers that replaced original hydronic or gravity systems, with sensor cables run along old siding or through tight basements. North Shore homes on slopes tend to have long, exposed exterior walls where a cable takes the weather hard. Townhouse and strata buildings in Richmond, Coquitlam, Surrey and the Tri-Cities can limit where a sensor may be mounted, and strata rules sometimes require approval before anything is fixed to an exterior wall. Newer homes in Surrey, Langley and Delta frequently have in-floor radiant heat, where a working outdoor reset curve makes a noticeable difference to comfort.

Our climate is the reason outdoor reset matters so much here. Metro Vancouver spends most of the heating season in mild, wet weather with occasional cold snaps, so a boiler stuck on a fixed curve is wrong most of the time: too hot on the many mild days, and sometimes not hot enough when an outflow wind arrives. The same rain is why corroded sensor connections are a common cause locally, and why we seal every outdoor connection we touch.

BC Wide Home Services Ltd has served Metro Vancouver since 1999 as an independent, TSBC-licensed gas contractor, licence LGA0090068, with Class B gas licence CGA0028029. We are not a Viessmann dealer or authorised warranty centre; Viessmann is one of the boiler brands we service, alongside IBC, Navien, Lochinvar, Buderus, Weil-McLain and Triangle Tube. Call (604) 473-9690 to book.

  • Independent TSBC-licensed contractor, with the work done by our own licensed gas fitters.
  • Permits and inspections arranged where the work requires them, such as gas piping, venting or a boiler replacement.
  • A written quote before any work beyond diagnosis, and a written record of the readings and tests when we finish.
  • Same-day service where we can, with an honest arrival estimate rather than a guaranteed window.
  • Boiler brands we service include Viessmann, IBC, Navien, Lochinvar, Buderus, Weil-McLain and Triangle Tube.

More questions homeowners ask

What does error code 18 mean on a Viessmann boiler?

It means the outdoor temperature sensor circuit is open: the sensor lead is broken, disconnected or the sensor has failed, so the boiler cannot read the outside temperature. Confirm the exact meaning against the manual for your unit. Heating usually continues at a default curve, but the boiler stops adjusting its water temperature to the weather until the circuit is repaired.

Can I reset Viessmann boiler error code 18 myself?

You can press reset once if your owner manual allows it, but a reset rarely clears code 18 for long because the cause is a physical break in the sensor circuit. If it comes back, stop resetting and book a licensed technician. Never open the control housing or bridge the sensor terminals to make the code go away.

Is it safe to run my Viessmann boiler with code 18 showing?

Usually yes, for a short time, because code 18 is a sensing fault and the boiler normally keeps heating on a default curve. It is not safe to ignore any other warning at the same time, such as a gas smell, a carbon monoxide alarm, water on the floor or repeated lockouts. If you smell gas or a CO alarm sounds, leave the house and call FortisBC or 911 from outside.

Why did Viessmann code 18 show up right after painting or siding work?

Because the outdoor sensor cable is thin and runs along the outside wall, it is easy for painters, siding crews or landscapers to cut, staple through or disconnect it without noticing. Look at the sensor and the visible cable from outside, then have a technician test and repair the circuit. Mention the recent work when you book, as it often shortens the diagnosis.

How much does it cost to fix Viessmann boiler error code 18?

The visit starts with the diagnostic service call fee shown in the repair-visit section above, and the repair itself is quoted in writing before any work beyond diagnosis begins. An outdoor sensor or cable repair is one of the simpler, less expensive boiler repairs. A control-input fault costs more, which is why we prove the sensor and cable first.

Can BC Wide fix Viessmann boiler error code 18 the same day near me in Greater Vancouver?

Same-day where we can, depending on the day’s calls and your location in Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta or Langley. We give an honest arrival estimate rather than a guaranteed window. Call (604) 473-9690 and tell us the code and whether you still have heat.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote