★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Viessmann Boiler Code A4 — Air lock in pump / low flow rate | BC Wide

Boilers, Error Codes, Hvac

Viessmann Boiler Code A4 — Air lock in pump / low flow rate | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Viessmann Boiler Code A4 — Air lock in pump / low flow rate | BC Wide

Viessmann Boiler Code A4 — Air lock in pump / low flow rate | BC Wide

Quick answer

Viessmann boiler error code A4 means the boiler has detected an air lock in the pump or a low flow rate through the heating circuit, so heat cannot move out of the boiler properly (confirm against the manual for your unit). Check the pressure gauge, make sure radiator valves are open, bleed radiators if you know how, and reset once only if the manual allows it. If A4 comes back, stop resetting and call a licensed technician at (604) 473-9690.

If your Viessmann boiler is showing A4 (Air lock in pump / low flow rate), here’s exactly what it means and what to do. This guide is part of our full Viessmann boiler error code list.

Severity: Needs attention.

What A4 means on a Viessmann boiler

An air lock in the circulation pump or a low flow rate has been detected, limiting heat transfer.

Common causes

  • Air locked in the pump or heating circuit
  • Low system pressure
  • Blocked or closed valves

What you can safely check first

  1. Check system pressure and top up via the filling loop if you know how
  2. Bleed radiators of air
  3. Reset once

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Viessmann boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Viessmann boiler repair across Greater Vancouver

If a Viessmann boiler showing A4 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Viessmann boiler codes

Frequently asked questions

Is A4 on a Viessmann boiler serious?

It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs Viessmann boilers 7 days a week across Greater Vancouver.

How do I reset a Viessmann boiler after A4?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

Viessmann boiler error code A4: what it means for your heat and hot water

In plain terms, A4 is the boiler telling you that water is not moving through it the way it should. As described at the top of this page, the control has detected an air lock in the circulation pump or a low flow rate, and that limits heat transfer. Confirm the exact wording against the manual for your unit, because display text and behaviour vary between control generations. The burner can still make heat, but if the pump is spinning in a pocket of air, or the water is barely moving, that heat stays trapped in the heat exchanger instead of reaching your radiators, in-floor loops or hydronic convectors.

What that means for you depends on how your system is set up. On a heating-only boiler, you will usually notice cold or lukewarm radiators while the boiler itself seems to be trying to work. If your boiler also heats an indirect hot water tank, or it is a combi unit that makes domestic hot water directly, the same flow problem can cut into your hot water as well. The boiler protects itself by limiting or stopping the burner, which is the right behaviour: firing a burner with little or no water moving can overheat the heat exchanger, and steam pockets inside a sealed system are noisy and damaging.

A4 is not a gas-leak code, but it is a sign the boiler is working outside its design conditions. Treat it as needs attention: a short window for a few owner-safe checks, then a licensed diagnosis if the code does not clear and stay clear. Here is how it usually shows up in a home, in the words owners use when they call us:

  • Radiators or floor loops are cold, or only warm at the top, even though the boiler display is lit
  • Gurgling, trickling or rushing-water sounds in the pipes or behind the boiler cover
  • A pump that hums, whines or rattles more than it used to
  • The pressure gauge reads lower than it normally does, or the needle drops again after a top-up
  • The heat comes on, shuts off within minutes, and A4 appears again
  • Hot water from a combi boiler or indirect tank runs lukewarm or swings between hot and cool
  • A damp patch, a drip, or crusty white or green residue near a fitting, a valve or the relief valve outlet

Viessmann boiler error code A4: what we check first

These are the causes we find most often when a Viessmann boiler shows A4 in a Metro Vancouver home, listed roughly from most common to least common. Every system is different, so treat this as a map, not a diagnosis.

1. Air trapped in the pump or the heating circuit. This is the classic cause after any work on the system: a new radiator, a drained loop, a replaced valve, or even a long summer shutdown where small weeps let air in. Air collects at high points and in the pump housing, and a pump cannot move water it cannot grip. Automatic air vents that have stuck shut, or are weeping water instead of venting air, are part of this picture.

2. Low system pressure. A sealed hydronic system needs enough pressure to push water up to the highest radiator and to keep dissolved air from coming out of the water. When pressure drops, air pockets form at the top of the system and flow falls off. Pressure loss always has a cause: a slow leak at a fitting or radiator valve, a relief valve that weeps, or an expansion tank that has lost its air charge and no longer absorbs expansion properly.

3. Closed or partly closed valves. Isolation valves under the boiler, zone valves, radiator valves and thermostatic radiator heads can all restrict flow. We regularly find a valve that was closed during a renovation or a painting job and never reopened, or a zone valve actuator that has failed in the closed position.

4. Sludge, magnetite and debris. Metro Vancouver water is soft, so hard-water limescale is rarely the story in hydronic systems here. What we do see is corrosion sludge: black magnetite from steel radiators and pipe, plus debris in older systems. It settles in strainers, dirt separators, heat exchanger passages and low spots, and it chokes flow over time.

5. A weak or failing circulation pump. Pumps are wear parts. Bearings get noisy, impellers wear or pick up debris, and speed-controlled pumps can lose their control signal. A pump that runs but moves too little water produces exactly the condition A4 describes.

6. Sensor, wiring or control faults. Less often, the flow or pressure reading itself is wrong because of a faulty sensor, a loose connector or a control fault. We suspect this last, because replacing parts on a guess is how homeowners end up paying for a repair that did not fix anything. The table below sets out each cause, what you may notice, what you can safely check, and where it becomes licensed work.

Likely causeWhat you may noticeOwner-safe checkWhen it becomes a licensed call
Air in the pump or systemGurgling, cold radiator tops, a noisy pumpBleed radiators with a radiator key if you know how, then recheck the gaugeA4 returns within a day or two, or bleeding keeps producing air
Low system pressureGauge sits below its normal readingTop up through the filling loop only if the manual shows how and you are comfortable doing itPressure drops again after a top-up, which points to a leak, relief valve or expansion tank problem
Closed or partly closed valvesOne zone or one radiator cold while others are warmConfirm radiator valves are open; never force a stiff or seized valveZone valves, isolation valves under the boiler, or any valve that will not turn
Sludge and debrisSlow warm-up, cold bottoms on radiators, dark water at the bleed pointNote the colour of the water from the bleed point and tell the technicianAlways: cleaning, filtering and treating the system is technician work
Weak or failing pumpHumming or rattling, little heat leaving the boilerListen and describe it; do not open the pump or the boiler casingAlways: pump testing and replacement is technician work
Sensor or control faultA4 even though pressure looks normal and radiators were heatingWrite down when the code appears and what the gauge readsAlways: electrical testing inside the boiler is licensed work

Can I reset a Viessmann boiler with error code A4? Owner-safe checks and where to stop

Yes, once, if your owner manual describes a reset for this condition. Before you press anything, work through the checks below in order. They are the only steps we recommend a homeowner take. Everything inside the boiler casing, on the gas train or in the control wiring is licensed work in BC, and the gas side may only be touched by a licensed gas fitter.

Do not open panels, bypass or jumper anything, cap or plug the relief valve, or keep resetting the boiler to squeeze out a bit more heat. Repeated resets on a flow fault push the heat exchanger toward overheating and can hide a second fault the control is trying to show you.

Gas and carbon monoxide safety: if you smell gas, a rotten-egg or sulphur smell, or your carbon monoxide alarm sounds, do not touch switches, do not reset the boiler and do not look for the source. Get everyone out, then call FortisBC or 911 from outside the home. Every home with a gas boiler should have working CO alarms near sleeping areas and on each level.

  • Power and switch: make sure the boiler service switch is on and the breaker has not tripped. If a breaker trips again after you reset it, leave it off and call.
  • Gas supply: confirm the manual gas valve on the line to the boiler is open, with the handle in line with the pipe. Do not adjust anything else on the gas piping.
  • Thermostat: confirm the thermostat or room control is set to heat and asking for a temperature above the current room temperature, with fresh batteries if it uses them.
  • Pressure gauge: read it and compare it with the normal range marked on the gauge or given in the manual. Write the reading down for the technician.
  • Radiators: bleed air with a radiator key, starting on the lowest floor and working up, with a cloth ready for drips. Recheck pressure afterwards, because bleeding lowers it.
  • Filling loop: top up only if the manual shows the procedure, only to the normal range, and close the filling valves fully when you finish.
  • Outside terminal: check that the intake and exhaust terminal outside is clear of leaves, nests, debris or, after one of our rare cold snaps, snow and ice.
  • Condensate drain: look at the visible condensate line and trap for kinks, a loose connection or water backing up. Do not dismantle it.
  • One reset: if the manual allows it, reset once and watch a full heating cycle. If A4 returns, stop resetting.

How our Viessmann boiler A4 repair visit works, step by step

Diagnostic service calls are $189.00. That covers a licensed technician coming to your home and finding the actual cause of A4 rather than guessing at it. The visit follows the same sequence every time, set out step by step below.

Parts most often involved in this kind of fault are the circulation pump, automatic air vents, the expansion tank, the pressure relief valve, zone valves and their actuators, strainers or dirt separators, and occasionally a pressure or flow sensor. Many A4 calls end with a proper purge, a pressure correction and a small leak repair, with no major parts at all.

What you should see in writing at the end: the cause we found, what we did, the readings before and after, and anything worth watching, such as a slow pressure loss that suggests an expansion tank nearing the end of its life.

  • Booking and triage: when you call (604) 473-9690 we ask what the display shows, what the gauge reads, whether you have heat and hot water, and what you have already tried. We book same-day where we can; in a cold spell the schedule fills, and we tell you honestly when the earliest slot is.
  • Safety on arrival: the technician checks for gas leaks and carbon monoxide around the boiler and venting before working on the fault itself.
  • Reading the boiler: we review the fault history and operating information available on the control, read the system pressure, and compare supply and return temperatures across the boiler.
  • Flow and air: we test the pump with the right meters, listen for cavitation, purge air from the pump and the system at the proper purge points, and check the automatic air vents.
  • Pressure and expansion: we check the expansion tank charge, inspect the relief valve and trace any leak that explains pressure loss.
  • Valves and debris: we confirm isolation and zone valves open fully, check strainers or dirt separators, and look at the water for sludge.
  • Controls: if flow is good and A4 persists, we test the relevant sensor and wiring instead of swapping parts on a hunch.
  • Written quote: before any work beyond the diagnosis, you get a written quote describing the repair and what it fixes. Nothing goes ahead without your approval.
  • Repair and proving: after the repair we run the boiler through a full heating cycle, confirm flow, pressure and temperature rise are normal, test the safeties, and check combustion and venting before we leave.

Repair or replace an older Viessmann boiler that keeps showing A4?

A4 on its own is rarely a reason to replace a boiler. Air, pressure and valve problems are repairable, and a pump is a normal wear part. The conversation changes when A4 is a symptom of something bigger, and the situations listed below are the ones where we raise replacement.

If replacement is on the table, the in-home estimate for a new boiler is free, and if you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation. We will also tell you plainly when a repair makes more sense. We would rather keep a sound boiler running than sell one you do not need.

BC Wide is an independent TSBC-licensed contractor, not a factory-authorised dealer or warranty centre for any manufacturer. On the boiler side, the brands we service include Viessmann, Navien, Rinnai, Bosch and A. O. Smith, and we discuss every brand neutrally. When we quote a replacement we look at what your home actually needs: heat loss, the number of zones, whether you want domestic hot water from the boiler, venting options and the condition of the existing piping. Any capacity or efficiency figure comes from the manufacturer’s published documents for that model, and you can verify it.

A boiler replacement in BC needs a gas permit and an inspection. A correct job includes flushing or cleaning the old system, adding a dirt separator or filter where it is needed, setting up proper air elimination and expansion, and commissioning the new boiler to the manufacturer’s instructions. Skipping the system cleaning is one of the most common reasons a new boiler starts showing flow faults within a season or two.

  • The heat exchanger is badly fouled with sludge and flow cannot be restored with cleaning and water treatment
  • Leaks are appearing at the boiler itself, not just at radiators or fittings
  • Parts for your control generation are hard to source and the unit is well into its expected service life
  • You are facing a major repair on a boiler that already has a history of other faults
  • Your home has changed, with a renovation, new zones or added floor area, and the boiler no longer suits the system

Viessmann boiler error code A4 service across Greater Vancouver

BC Wide Home Services Ltd is a TSBC-licensed independent contractor based in Burnaby and serving Metro Vancouver since 1999, under gas contractor licence LGA0090068 and Class B gas licence CGA0028029. Our licensed gas fitters take out permits where the work requires them, arrange the inspections, and give you a written quote before any work beyond diagnosis.

Vancouver: many hydronic systems here sit in older character homes and house conversions, where original radiators and decades of pipe changes make air and sludge common contributors to A4. Burnaby and New Westminster: a mix of older houses, townhouses and low-rise strata, often with hydronic systems that have been partly upgraded over the years. Surrey, Delta and Langley: many larger detached homes with in-floor radiant loops and several zones, where one stuck zone valve can starve the boiler of flow. Richmond: plenty of homes with radiant floors, so we pay close attention to loop flow and air elimination. Coquitlam and the Tri-Cities: hillside homes where the highest radiator can sit well above the boiler, which makes correct system pressure more important. The North Shore: larger homes with long pipe runs, and colder nights at elevation that expose a marginal system.

Our mild, wet coastal climate means boilers run for long stretches at low to moderate output from fall through spring. That is easy on a healthy system, but it also lets small air and pressure problems go unnoticed for weeks until the first properly cold spell exposes them. A4 calls tend to rise at the start of the heating season, after systems have sat idle all summer and small weeps have let air in.

In strata buildings with individual suite boilers, check with your strata before any work that touches shared venting or common piping. We can coordinate access and permits with the strata manager so the repair is done once and done properly.

More questions homeowners ask

What does Viessmann boiler error code A4 mean?

It means the boiler has detected an air lock in the pump or a low flow rate, which limits heat transfer out of the boiler; confirm against the manual for your unit. In practice, water is not moving through the heating circuit properly, so you may lose heat or hot water. The usual causes are trapped air, low pressure, closed valves, sludge or a weak pump.

Can I reset a Viessmann boiler showing A4?

Yes, once, and only if your owner manual describes a reset for it. Check the pressure gauge, confirm radiator valves are open and bleed air first if you know how. If A4 returns after one reset, stop and call a licensed technician, because repeated resets can push the boiler toward overheating.

Is it safe to run a Viessmann boiler with error code A4?

The boiler limits or stops the burner to protect itself, so it is not meant to run normally while A4 is active. Do not try to keep it going with repeated resets. If you smell gas or a carbon monoxide alarm sounds, leave the home and call FortisBC or 911 from outside.

Why does my Viessmann boiler keep losing pressure and showing A4?

Pressure that drops after a top-up always has a cause, usually a leak at a fitting or radiator, a weeping relief valve or an expansion tank that has lost its charge. Topping up again and again brings in fresh oxygen-rich water, which feeds corrosion and sludge. A licensed technician needs to find the leak or failed part.

How much does it cost to fix Viessmann boiler error code A4?

Diagnostic service calls are $189.00, and that visit finds the actual cause. The repair itself depends on what we find, from a purge and pressure correction to a pump or expansion tank, and you get a written quote before any work beyond diagnosis. If you go ahead with a replacement through BC Wide instead, the $189.00 diagnostic charge is waived and taken off the installation.

Who repairs Viessmann boilers near me in Greater Vancouver?

BC Wide is an independent TSBC-licensed contractor based in Burnaby, serving Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We service Viessmann boilers but are not a factory-authorised dealer or warranty centre. Call (604) 473-9690 and we will book same-day where we can.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote