Viessmann Combi Boiler Installation in Coquitlam
- A combi boiler is one wall-hung gas appliance that heats your home and makes hot water on demand, so it only makes sense in a house that already has hydronic heating.
- Space heating pauses briefly while a hot tap runs, and hot water flow is finite; households that run several showers at once are often better served by a heat-only boiler with a separate indirect tank.
- A condensing combi needs a new sealed vent and a condensate drain; the old masonry chimney is not reused for it, and any appliance left on that chimney may need a liner.
- Metro Vancouver water is soft, so old hydronic systems here suffer from corrosion sludge rather than limescale; cleaning, flushing and a dirt separator protect the new heat exchanger.
- Ballpark installed range for a gas combi boiler in Greater Vancouver: $8,000 to $14,000 and up, before GST. This is not a quote; an accurate price needs a site visit.
- Gas piping, venting and commissioning are licensed gas fitter work in BC, done under a permit and inspected.
Installing a Viessmann combi boiler in a Coquitlam home means replacing an old boiler and a separate hot water tank (or an old boiler on its own) with one wall-hung, condensing gas appliance that heats your radiators, hydronic baseboards or in-floor loops and also heats domestic water as you use it. It suits homes that already have hot-water heating and households whose hot water use mostly happens one draw at a time. It is a poor fit for forced-air homes with no hydronic loop, and for busy households that routinely run two or three showers at once. The job is more than a swap: it needs a new sealed vent, a condensate drain, a gas supply checked against the new appliance’s input, rebuilt near-boiler piping, a cleaned system, a gas permit and inspection, and careful commissioning. For a gas combi boiler installation of any brand in Greater Vancouver, a ballpark installed range is $8,000 to $14,000 and up, before GST. That is a ballpark figure for orientation only and is not a quote; an accurate price needs a site visit. BC Wide Home Services Ltd is an independent TSBC-licensed contractor (LGA0090068, CGA0028029) that installs and services this family in Coquitlam. Call (604) 473-9690.
How does a Viessmann combi boiler actually work?
A combi boiler pairs a modulating, condensing gas burner and main heat exchanger with a small plate heat exchanger for domestic water. When nobody is using hot water, the boiler sends heating water around your radiators, baseboards or floor loops, and a three-way diverter valve holds the flow on the heating side. When a hot tap opens, a flow sensor detects the draw, the diverter valve swings the boiler’s heat over to the plate heat exchanger, and cold water from the main is heated as it passes through. Space heating pauses for those minutes. This is called hot water priority, and in a reasonably insulated house the rooms barely notice a shower’s worth of interruption.
Condensing means the appliance pulls so much heat out of the flue gases that water vapour condenses inside the heat exchanger. That recovered heat is where the efficiency comes from, and it has two practical consequences: the exhaust leaves cool enough to run through approved plastic venting, and the appliance produces a steady trickle of mildly acidic condensate that has to be drained. Condensing only happens when the water returning from the house is cool enough, which is why outdoor reset control, lowering the supply temperature on mild days, matters so much on a coastal job.
Viessmann publishes the burner input, hot water output, efficiency rating and venting limits for each unit in its combi family. We do not quote those numbers here because they vary by unit: they are manufacturer-published, so check the rating plate and the installation manual for your exact unit. BC Wide installs and services Viessmann combi boilers as an independent TSBC-licensed contractor. We are not a factory-authorised dealer or a warranty centre, and warranty terms and registration requirements are set by the manufacturer.
Is a combi boiler right for my home, or would a boiler with a separate tank be better?
The deciding question is how your household uses hot water, not how big the house is. A combi heats water as it flows, so it does not run out the way a tank does, but it can only deliver so much hot water at one time. In winter the water coming in from the main is colder, so the same burner delivers less flow at shower temperature than it does in August. Size and suitability are settled by matching the manufacturer-published output against your real usage, which is why we ask about bathrooms, fixtures and routines at the site visit.
- Good fit: an existing hydronic system (radiators, hydronic baseboards or in-floor loops) with an ageing boiler and a separate gas tank you want to retire.
- Good fit: one or two bathrooms, with hot water draws that mostly happen one at a time.
- Good fit: a cramped mechanical room where the floor space a tank occupies is worth recovering.
- Poor fit: a forced-air house with ducts and no hydronic loop; a combi would have nothing to heat.
- Poor fit: a household that regularly runs two or more showers while laundry or the dishwasher is going; a heat-only boiler with an indirect tank handles stacked demand better.
- Poor fit: a large soaker tub you want filled quickly, because fill time depends on flow rate.
- Poor fit: a house with no code-compliant route for a sealed vent and a condensate drain.
What is involved in replacing a boiler and a hot water tank with one combi?
Retiring two appliances and installing one touches every system around them: gas, venting, heating water, domestic water connections at the appliance, drainage and controls. The table lists the main stages and who is allowed to carry out each one.
- Most straightforward replacements take one to three working days; a long vent route or a new gas line from the meter adds time.
- Heat and hot water are off for part of that window, so we plan the cutover with you, ideally outside the coldest stretch of the year.
| Stage | What happens | Who does it |
|---|---|---|
| Site assessment | Heat loss estimate, hot water demand review, vent route, gas supply, drain location and system condition checked | Licensed contractor; the homeowner supplies usage details |
| Permit | Gas permit taken out before work starts | Licensed gas contractor |
| Removal | Gas shut off and capped, old boiler and tank drained, disconnected, removed and disposed of | Licensed gas fitter |
| Chimney | Old flue opening sealed, or chimney relined if another gas appliance still uses it | Licensed gas fitter |
| Mounting and piping | Combi hung on the wall, hydraulic separation, circulator, expansion tank, air and dirt separation installed | Licensed gas fitter or hydronic installer |
| Venting and condensate | Sealed intake and exhaust run and terminated, condensate trap, neutraliser and drain connected | Licensed gas fitter |
| Gas connection | Supply sized for the new input, connected and leak tested | Licensed gas fitter |
| Power and controls | Boiler power, outdoor sensor, zone controls and thermostat wiring | Licensed trades; the homeowner does not open the appliance |
| Clean, flush and fill | System cleaned, refilled, air purged, water treated where the manufacturer calls for it | Licensed installer |
| Commissioning and inspection | Combustion analysis and settings to the manual, then inspection by the authority having jurisdiction | Licensed gas fitter, then the inspector |
How are venting, condensate and the gas supply handled?
Venting. A condensing combi is a sealed-combustion appliance: it draws combustion air through one pipe and pushes exhaust out through another, usually out a side wall or up through the roof, using only the vent materials the manufacturer approves. The old masonry chimney cannot be used for it. Where the terminal goes is set by code clearances from windows, doors, air intakes, soffits, inside corners, grade and property lines, and by the manufacturer’s maximum vent length and elbow count. On a narrow lot with a neighbour close on each side, finding a legal termination point is often the hardest part of the design.
The orphaned chimney. If the old boiler and tank shared a chimney with another gas appliance that is staying, taking them out can leave that appliance alone in a flue that is now far too large for it. An oversized flue lets exhaust cool, condense and draft poorly. The usual fix is a correctly sized liner, and it has to be assessed at the site visit, not discovered on install day.
Condensate. The condensate is mildly acidic, so it runs through the boiler’s trap, usually through a neutraliser, and on to a floor drain, laundry standpipe or condensate pump. If the mechanical room has no drain nearby, a pump and discharge line add labour. Any condensate line that passes through a garage, crawlspace or exterior wall must be protected from freezing, which is a real concern in the colder snaps on Coquitlam’s hillside neighbourhoods.
Gas supply. A combi’s burner input when it is making hot water is often higher than the input of the boiler it replaces, because heating water on demand takes a lot of heat quickly. The gas line, and sometimes the meter, has to be checked against the combined load of every gas appliance in the house at their actual pipe lengths. An undersized line shows up as weak or fluctuating hot water and unstable combustion. Sometimes the existing line is adequate; sometimes a new, larger run from the meter is needed. In older houses this is one of the most common hidden blockers.
Why does the old system water matter, and what changes in the piping?
Metro Vancouver water is soft, and some of it comes from the Coquitlam watershed just north of the city, so limescale is not what damages hydronic systems here. The problem is corrosion. Over decades, oxygen that gets into the system reacts with steel and cast iron and forms black magnetite sludge. A modern condensing heat exchanger has narrow waterways, and old sludge flushed into it can restrict flow, cause kettling noises and overheating, and shorten its life.
A proper installation therefore includes cleaning the existing system with a suitable cleaner, flushing it, fitting a dirt and magnetite separator on the return, and filling with treated water where the manufacturer specifies it. Some older radiant floors use tubing without an oxygen barrier, which keeps letting oxygen in; those loops are often isolated from the boiler with a plate heat exchanger so the new appliance only sees clean water.
Near the boiler, the piping is usually rebuilt with hydraulic separation, either a low-loss header or closely spaced tees, so the boiler’s pump and the heating zones do not fight each other. A correctly sized expansion tank, an air separator and isolation valves for future service go in at the same time. On the domestic side, a mixing valve is added where needed for scald protection. An outdoor temperature sensor lets the controls drop the supply temperature on mild days, which keeps the return water cool enough to condense.
What does Coquitlam’s housing stock mean for a combi installation?
Many homes here fall into a few broad groups, and each one changes the job. Older houses in and around Maillardville, Austin Heights and central Coquitlam, many of them mid-century, are where hot-water heating with cast-iron radiators, hydronic baseboards or early in-floor loops turns up most often. These systems tend to carry decades of sludge, sit in basement mechanical rooms beside an old chimney, and run on gas lines sized for appliances that used less gas. They are often good combi candidates once the water, venting and gas supply are dealt with properly.
Houses from the 1980s and 1990s, including many on Westwood Plateau, are more often forced air. Where they do have hydronic heat, it is usually baseboard or in-floor loops, and the mechanical room is frequently in a garage or finished basement, so routing a new vent and condensate line through finished walls needs planning. Newer homes on Burke Mountain and in the northeast were more commonly built with high-efficiency equipment, and a combi there is often a like-for-like replacement where the vent and drain already exist, though the old unit’s vent must still be confirmed as approved for the new one.
Townhouses add another layer. Vent terminations on exterior walls and roofs can be governed by strata bylaws, so the owner confirms with the strata council what is allowed before the design is final; we do not assume. Questions about heritage properties go to the City of Coquitlam.
Climate matters too. The lower neighbourhoods have a mild, wet coastal climate, while the hillside areas toward the mountains see more snow and colder nights. That spread suits a modulating boiler: for most of the season demand is low and the burner turns down instead of cycling on and off, while the heat loss calculation has to cover the cold snaps up the hill. Vent terminals are placed above expected snow lines and away from spots where heavy rain runoff or drifting snow could block them.
How much does a combi boiler installation cost in Coquitlam?
The figures below are ballpark installed ranges for Greater Vancouver, before GST, for orientation only. They are not a quote, and an accurate price needs a site visit. They apply to gas combi installations generally, not to any one brand or model.
What moves the number is usually the work around the boiler rather than the boiler itself.
Vent route: a short side-wall run close to the boiler is far simpler than a long run with several elbows through finished space or up through the roof, and relining a chimney for an appliance that stays adds to the job.
Gas supply: if the existing line can carry the new load, this is a minor item; if a new run from the meter is needed, it is one of the largest variables.
System condition: heavy sludge means more cleaning, a separator, sometimes a plate heat exchanger for older floor tubing, and occasionally replacement of seized valves or leaking radiator connections.
Condensate and power: a nearby floor drain is simple, while a pump and long discharge run is not; new power, an outdoor sensor and multi-zone controls vary with how the house is zoned.
Access, removal and disposal: a tight basement stair, a heavy cast-iron boiler, or a garage installation with finished walls all change labour, and taking out and disposing of two old appliances is part of the job.
Permits and code items: permit fees are set by each municipality or Technical Safety BC. Code corrections found during the work, such as clearances, bonding or an unsafe existing vent, add to the scope.
Programs for high-efficiency heating change over time and carry their own eligibility rules. We explain what may apply at the site visit, and you confirm the details with the program itself. Ask about payment options at the same visit.
- Gas combi boiler installation, typical replacement: $8,000 to $14,000 and up.
- Heat-only condensing gas boiler replacement, where a combi does not suit the household: $7,000 to $15,000.
- New or upsized gas line, short and accessible: $500 to $1,500.
- New or upsized gas line, long or difficult: $1,500 to $3,000 and more.
What happens on install day: permit, inspection and commissioning?
Before work starts, the licensed contractor takes out the gas permit. Depending on the address, the authority having jurisdiction for gas work is Technical Safety BC or the municipality, and the installer confirms which applies. After the installation, the work is inspected.
Commissioning is where a good installation separates from one that is merely connected. The technician confirms inlet gas pressure under load, checks the gas type setting, runs a combustion analysis at high and low fire and adjusts to the manufacturer’s procedure, tests for carbon monoxide in the flue gas and in the room, primes the condensate trap, purges air from the system, sets the heating curve and outdoor reset, sets the hot water temperature with scald protection in mind, and confirms every zone calls for heat and satisfies.
You should get a walkthrough before we leave: where the gas shutoff is, what pressure range the gauge should show, what the display is telling you in plain terms, and when the first service is due. Afterwards, a homeowner can keep the area around the boiler clear, glance at the pressure gauge, keep the outdoor vent terminals free of snow, leaves and plants, and test CO alarms. Opening the casing, touching the gas valve, burner or venting, and repeatedly repressurising a system that keeps losing pressure are jobs for a licensed technician.
When should I call a licensed technician?
For no-heat or no-hot-water calls in Coquitlam we offer same-day service where we can, depending on the day’s schedule and parts availability, and we will not promise an arrival window we cannot keep. Installations are planned jobs, scheduled after the site visit and the permit. Call BC Wide at (604) 473-9690.
- You smell gas: leave the house first, then call your gas utility’s emergency line or 911 from outside.
- A CO alarm sounds, or people in the house have headaches, nausea or drowsiness that ease when they go outside.
- The boiler locks out again after a single reset.
- System pressure keeps dropping, or the relief valve drips or discharges.
- Hot water turns lukewarm or swings in temperature, or the boiler bangs, kettles or short-cycles.
- Condensate is pooling around the boiler, or the outdoor vent terminal is damaged or blocked.
- You are planning to replace an old boiler and tank and want the vent route, gas supply and system water assessed before choosing equipment.
Frequently asked questions
Can a Viessmann combi boiler replace both my boiler and my hot water tank?
Yes, if your home already has hydronic heating and your household mostly uses hot water one draw at a time. The combi takes over both jobs, and the tank and its chimney connection are removed. If you regularly run several showers at once, a heat-only boiler with a separate indirect tank is usually the better choice.
Will a combi boiler give enough hot water for two showers at once?
It depends on the unit’s manufacturer-published hot water output and on how cold the incoming water is, which is coldest in winter. Some households find two showers workable and others find it marginal. We match the output on the rating plate and in the installation manual against your fixtures and routines before recommending a combi.
Can the new boiler use my old chimney?
No. A condensing combi uses a sealed vent system approved by the manufacturer, usually terminating on a side wall or roof. If another gas appliance stays on the old chimney, that chimney may need a correctly sized liner, which we check at the site visit.
Do I need a permit for a combi boiler installation in Coquitlam?
Yes. The installation needs a gas permit and an inspection, and the licensed contractor takes out the permit with the authority having jurisdiction for your address, either Technical Safety BC or the municipality. Permit fees are set by that authority. Townhouse owners should also confirm with their strata council what the bylaws say about exterior vent terminations.
Is BC Wide a Viessmann dealer or warranty centre?
No. BC Wide is an independent TSBC-licensed contractor that installs and services Viessmann combi boilers. Warranty coverage and registration requirements are set by the manufacturer, so check the documentation that comes with your unit.
Our water is soft, so do we still need to flush the old system?
Yes. Soft water means limescale is not the concern here, but older hydronic systems build up corrosion sludge over the years. That sludge can clog a new condensing heat exchanger, so cleaning, flushing and a dirt separator are part of a proper installation.
How long does a combi boiler installation take?
Most straightforward replacements take one to three working days. A long vent route, a new gas line from the meter, heavy system cleaning or a chimney liner can extend that. We plan the cutover so you know when heat and hot water will be off.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
How often should a boiler be serviced?
How much does a new boiler cost in Vancouver?
How long does a boiler last?
My boiler is making a banging or kettling noise. Is that dangerous?
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Should I repair or replace my old boiler?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


