★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Weil-McLain Boiler Code E00 — Flame detected at startup (false flame) | BC Wide

Boilers, Error Codes, Hvac

Weil-McLain Boiler Code E00 — Flame detected at startup (false flame) | BC Wide — BC Wide Heating & Air Conditioning, Greater Vancouver
Home › Weil-McLain Boiler Code E00 — Flame detected at startup (false flame) | BC Wide

Weil-McLain Boiler Code E00 — Flame detected at startup (false flame) | BC Wide

Quick answer

Weil-McLain error code E00 means the boiler control sensed a flame signal before the burner should have been lit, a so-called false flame, and went into a hard safety lockout (confirm against the manual for your unit). Expect no heat, and no hot water if the boiler heats your tank. Confirm the gas supply is on and reset once, only if your manual allows it. If E00 returns, stop and book a licensed gas technician at (604) 473-9690.

If your Weil-McLain boiler is showing E00 (Flame detected at startup (false flame)), here’s exactly what it means and what to do. This guide is part of our full Weil-McLain boiler error code list.

Severity: Critical — likely no heat / lockout.

What E00 means on a Weil-McLain boiler

Hard lockout. The control sensed a flame signal before the burner should be lit (a ‘false flame’ or flame present at standby), so it locked out for safety.

Common causes

  • Flame sensor / ignition electrode fault or contamination
  • Gas valve not fully closing
  • Moisture or short on the flame-rod circuit
  • Control board fault

What you can safely check first

  1. Confirm the gas supply is on, then reset the control once
  2. If it locks out again, stop and call a licensed gas technician — the flame-sensing/gas-valve circuit must be inspected by a pro

Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.

When to call a technician

This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a Weil-McLain boiler usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.

BC Wide Heating & Air Conditioning has serviced Greater Vancouver boilers since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.

Weil-McLain boiler repair across Greater Vancouver

If a Weil-McLain boiler showing E00 won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast boiler repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.

Related Weil-McLain boiler codes

Frequently asked questions

Is E00 on a Weil-McLain boiler serious?

It’s a lockout/safety code — the boiler has shut down and needs prompt diagnosis. BC Wide repairs Weil-McLain boilers 7 days a week across Greater Vancouver.

How do I reset a Weil-McLain boiler after E00?

You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.

What does Weil-McLain error code E00 mean for your heat, hot water and safety?

In plain terms, E00 is the boiler refusing to trust itself. Before every heating cycle the control checks that there is no flame in the combustion chamber, because at that moment there should not be one. If it sees what looks like a flame signal while the gas valve is meant to be closed, it cannot tell whether that signal is a real flame fed by gas getting through, or an electrical signal that only looks like a flame. Either way it shuts everything down and holds a hard lockout. Confirm against the manual for your unit, since display wording varies between control generations.

For you that usually means three things. First, the house stops getting heat from the boiler: radiators, baseboard convectors or in-floor loops go lukewarm and then cold over the next few hours. Second, if the boiler also heats your domestic water through an indirect tank, the hot water runs out once the stored supply is used. Third, and most important, the boiler is telling you something about the burner, the flame-sensing circuit or the gas valve that needs a licensed person to look at. A lockout is the safety system doing its job, not a nuisance to clear.

These are the symptoms owners usually describe to us when they call about this code:

  • The display shows E00 and the boiler will not fire, even though the thermostat is calling for heat.
  • Radiators or floors are cold, or only warm on the pipes closest to the boiler.
  • Hot water from an indirect tank runs out sooner than usual or goes cold.
  • The boiler ran after a reset, then went straight back to E00 on the next call for heat.
  • You hear the fan or the circulator start, then everything stops with the code showing.
  • The fault started after a wet spell, a leak near the boiler, or recent work in the mechanical room.
  • You notice a faint gas odour near the boiler. Treat that as a safety situation, not a troubleshooting step.

Weil Mclain Boiler Error Code E00: what we check first

These are the likely causes, ordered by how often a false-flame lockout traces back to each one in general practice on modern gas boilers. The order is a guide, not a rule, and the actual cause on your boiler is only confirmed with meter readings taken on site. Nothing in this list is a homeowner repair; the table below says exactly where your part ends and the licensed part begins.

  • 1. A contaminated or damaged flame sensor or ignition electrode. The flame rod reads flame by passing a tiny current through the flame itself. Deposits on the rod, a cracked ceramic insulator or a rod that has shifted position can leak that signal to ground or hold a stray reading, so the control sees flame when the burner is off. This is the cause we find most often and the most routine one to correct.
  • 2. Moisture or a short on the flame-rod circuit. Water from a dripping relief valve, a weeping fitting above the boiler, condensate that has backed up, or plain damp in a basement mechanical room can track along a wire or terminal and create a false signal. Corroded connectors and chafed insulation do the same thing. This cause often shows up after a wet spell or a leak.
  • 3. A gas valve that is not fully closing. If gas seeps through the valve when it should be shut, a small real flame can persist after a cycle or appear before ignition. This is the cause that makes E00 a genuine safety fault, and it is why we never write off a repeat E00 as an electrical nuisance until the valve has been tested.
  • 4. A control board fault. The board interprets the flame signal, and if its sensing circuit fails it can report flame that is not there. We look at the board only after the sensor, wiring, ground path and gas valve have been tested, because a board is one of the more expensive parts on a boiler and replacing it first often does not fix the problem.
Likely causeWhat you can safely checkWhen it becomes a licensed call
Flame sensor or ignition electrode contamination or faultNothing inside the boiler. Note when the code appears and whether it returns after one permitted reset.Any return of E00. Removing, cleaning or replacing the flame rod is inside the sealed burner area and is gas work.
Moisture or short on the flame-rod circuitLook, without touching any wiring, for water dripping onto or near the boiler, a wet floor or an overflowing condensate pan, and report what you see.As soon as water is found near controls or wiring. Drying, repairing or replacing wiring and terminals is a technician job.
Gas valve not fully closingConfirm the manual gas shutoff on the line to the boiler is in its normal open position. Do not touch or adjust the gas valve itself.Immediately. A valve that leaks through is a gas safety fault. If you smell gas, leave the home first and call from outside.
Control board faultNote any other messages or lights on the display and when they appeared.Always. The board is tested and replaced only by a technician, after the other causes have been ruled out.

Can I reset a Weil-McLain boiler with error code E00, and when do I stop?

You may reset once, and only if your owner manual describes a reset for this lockout. A hard lockout is designed to stay locked until someone deliberately clears it, because repeated restarts on a false-flame fault can mean repeated ignition attempts with gas possibly already present. One reset tells you whether the event was a one-off. A second E00 tells you the fault is real and needs a technician.

Before that one reset, these are the owner-safe checks worth doing:

  • Power: confirm the boiler’s service switch is on and the breaker has not tripped. Do not open the boiler cabinet.
  • Gas supply: confirm the manual gas shutoff valve on the line to the boiler is in its normal open position. If another gas appliance in the home is working, the supply to the house is likely fine.
  • Thermostat: confirm it is set to heat and calling above room temperature, with fresh batteries if it uses them.
  • Outside terminals: from ground level, check the boiler’s intake and exhaust terminals for snow, leaves, nests or anything stacked against them, and clear loose debris by hand only.
  • Condensate drain: look at the visible condensate line and any neutralizer or condensate pump for an obvious kink, disconnection or overflow. Do not take it apart.
  • Water near the boiler: look for drips onto the cabinet, a wet floor or a discharging relief valve, and tell the technician what you found.
  • One reset: if the manual allows it, reset the control once and watch one full call for heat.

How our Weil-McLain E00 repair visit works, step by step

What you should not do before we arrive: open the front panel, remove the burner door, clean or bend the flame rod, unplug or jumper any wire, adjust the gas valve, or keep resetting the boiler to get through a cold night. In BC, work on the gas train, burner and ignition system is restricted to licensed gas fitters, and most electrical work inside the appliance is restricted to licensed trades. Those rules exist precisely for faults like this one.

Gas and carbon monoxide safety: if you smell gas, or a carbon monoxide alarm sounds, do not reset anything, do not operate switches, and leave the home with everyone in it. Call FortisBC or 911 from outside. A false-flame lockout can involve a gas valve that is leaking through, so take any odour seriously. Every home with a gas boiler should have working CO alarms near sleeping areas and on the level where the boiler is installed.

It becomes a licensed call when E00 returns after the one reset, when you find water on or near the controls, when the boiler has gone a long stretch without service, or when you have any doubt at all. Call (604) 473-9690. Same-day where we can, depending on the day’s bookings and your location; we will tell you honestly when the earliest slot is rather than promise an arrival window.

Diagnostic service calls are $189.00. That covers a licensed technician coming to the home and finding the cause with test equipment, not a guess at a part. Here is how the visit runs.

  • 1. Booking: we ask for the code, the boiler model from the rating plate if you can read it safely, what happened before the lockout, and whether anything else in the home runs on gas.
  • 2. Safety first on arrival: the technician checks for gas odour, checks carbon monoxide in the space, and looks at the venting and combustion air before trying to run the boiler.
  • 3. Reading the history: we review the lockout history on the control where the model stores it, and note the conditions when E00 appeared.
  • 4. Flame signal testing: with the right meters, we measure the flame signal with the burner off and during operation, and compare the readings with the manufacturer’s published values for your model.
  • 5. Sensor, wiring and ground: we inspect the flame rod, the ignition electrode, the insulator, the ground path and every connection on that circuit for contamination, moisture or damage.
  • 6. Gas valve: we test the valve for leak-through and correct closing, and check gas pressures against the manufacturer’s figures for your unit.
  • 7. Control board: only after the steps above are ruled out do we assess the board.
  • 8. Written quote: before any work beyond diagnosis, you get a written quote describing the cause found, the parts involved and the labour. Nothing proceeds until you approve it.
  • 9. Repair and safety test: after the repair we run the boiler through several full cycles, re-check the flame signal, test the safeties, confirm combustion and venting, and note the result so a return of the code is meaningful.

Should you repair or replace a Weil-McLain boiler that keeps showing E00?

Most E00 faults are repairs, not replacements. A contaminated flame rod, a wet connector or a failing gas valve are fixable parts on an otherwise sound boiler. The parts most often involved, in general terms, are the flame sensor or ignition electrode and its gasket, the wiring and connectors on the flame-sensing circuit, the gas valve, and less often the control board. We will not name a part as the cause until the readings support it, and we will show you the readings if you ask.

The repair-or-replace question only really opens when the false-flame fault is one symptom of a boiler that is wearing out overall. These are the factors we weigh with you, in writing:

  • Age and history: an older boiler with repeated lockouts across different faults is a different conversation from a newer one with a single sensor problem.
  • Heat exchanger and water condition: Metro Vancouver water is soft, so hydronic systems here suffer from sludge and corrosion rather than limescale. A corroded or fouled heat exchanger, or a system full of black water, changes the value of putting new parts on the boiler.
  • Parts availability: for older control generations some parts take time to source, and we will tell you honestly if a part is hard to get.
  • Venting and code: a replacement must meet current code for venting and combustion air, which can add work in older homes. A repair usually leaves the existing approved venting in place.
  • Repair cost against remaining life: we describe this qualitatively in the written quote so you can compare options without pressure.
SituationWhat usually makes sense
Single E00 lockout, boiler otherwise reliable, clean system waterRepair the cause found, test the safeties, carry on with regular maintenance.
E00 caused by water dripping onto the controlsFix the source of water first, then repair and dry the flame-sensing circuit.
Gas valve leaking through on a boiler in good overall conditionReplace the valve and fully test combustion and safeties.
Older boiler, repeated lockouts of different kinds, corroded heat exchanger or sludge-heavy systemGet a written repair quote and a replacement estimate side by side before deciding.

Weil Mclain boiler error code E00 service near me in Greater Vancouver

If replacement makes sense, the in-home estimate for a new boiler or installation is free, and if you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived, taken off the installation. A replacement conversation also covers sizing from a heat-loss calculation rather than matching the old boiler, whether the new boiler should also heat your domestic water, the condition of the radiators or floor loops, and whether the system needs flushing and a dirt separator so the new boiler does not inherit old sludge. If a repair is the right call, we will say so plainly.

BC Wide Home Services Ltd is an independent contractor licensed by Technical Safety BC (gas contractor licence LGA0090068, Class B gas CGA0028029), based in Burnaby and servicing boilers across Metro Vancouver since 1999. Our technicians are licensed gas fitters. Where a repair or replacement needs a permit, we pull it and the work is open to inspection, and you always get a written quote before work beyond diagnosis. We service Weil-McLain boilers as an independent contractor; we are not an authorised dealer or warranty centre for the brand, so if your boiler may still be under manufacturer warranty, check with the manufacturer before work begins and we will work with you on it.

Housing stock varies a lot across the region, and it shapes what we tend to find on an E00 call. The notes below are general patterns, not rules about any particular street or home.

  • Vancouver: many older detached homes and character houses have hydronic systems that have been updated over the decades, often with boilers in tight basement mechanical rooms where damp and old piping can affect wiring.
  • Burnaby: a mix of older single-family homes and newer multi-family buildings, so we see both basement boilers and compact wall-hung units in townhomes.
  • Surrey: many larger and newer homes, some with in-floor radiant loops, where long piping runs and zoning come into the diagnosis.
  • Richmond: low-lying ground and a damp climate mean we pay close attention to moisture in mechanical rooms and around controls.
  • Coquitlam and the Tri-Cities: hillside homes and townhouses where boiler location and terminal placement can complicate access.
  • The North Shore: heavy rainfall, older hydronic homes and outside terminals that collect leaves and forest debris.
  • New Westminster: older and heritage housing, plus strata buildings where shared mechanical rooms and strata approval can affect timing.
  • Delta: a mix of older ranchers and newer homes, often with boilers in garages or utility rooms.
  • Langley: newer subdivisions with radiant floors alongside older acreage homes.
  • Brands we service for boilers and hydronic heating, as an independent contractor: Weil-McLain, IBC, Viessmann, Navien, Lochinvar, Buderus, Triangle Tube and Rinnai. We are not a dealer for any of them.
  • Wet coast note: our mild, wet climate keeps boilers running through long shoulder seasons and keeps basement mechanical rooms damp, which makes moisture on the flame-sensing circuit a more common contributor here than in drier places. Keeping the area around the boiler dry, and fixing any drip above it, is one of the most useful things an owner can do.
  • To book, call (604) 473-9690 and mention the E00 code. Same-day where we can.

More questions homeowners ask

What does error code E00 mean on a Weil-McLain boiler?

It means the control detected a flame signal at startup when no flame should be present, a false flame, and put the boiler into a hard lockout for safety. Confirm against the manual for your unit. Common causes are a contaminated or faulty flame sensor, moisture or a short on the flame-rod circuit, a gas valve not closing fully, or a control board fault.

Can I reset a Weil-McLain boiler with an E00 code?

Once, and only if your owner manual allows a reset for this lockout. If E00 comes back, stop and call a licensed gas technician, because repeated resets can hide a gas valve that is leaking through. Never open the burner area, clean the flame rod yourself or jumper any wiring.

Is it safe to run my Weil-McLain boiler after an E00 lockout?

Not until the cause is known. If it runs normally after a single permitted reset, watch it closely and book an inspection if the code returns at all. If you smell gas or a carbon monoxide alarm sounds, leave the home and call FortisBC or 911 from outside.

How much does it cost to diagnose a Weil-McLain E00 code?

Diagnostic service calls are $189.00. After diagnosis you receive a written quote for any repair before work goes ahead. If you choose a replacement or new installation through BC Wide instead, the $189.00 diagnostic charge is waived and taken off the installation.

Who fixes Weil-McLain boiler error code E00 near me in Greater Vancouver?

BC Wide Home Services Ltd, a TSBC-licensed independent gas contractor based in Burnaby, services Weil-McLain boilers across Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. Call (604) 473-9690; same-day where we can.

Why does my Weil-McLain boiler show E00 after rain or a leak?

Moisture on the flame-rod circuit can create a stray signal that the control reads as flame. Water from a drip above the boiler, a discharging relief valve or a damp mechanical room is a common trigger on the wet coast. Fix the source of water, keep it off the boiler, and have a licensed technician dry and test the circuit.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote