What Commissioning Should Include
- Commissioning is the measuring, adjusting and documenting done after the new furnace is physically in place, and it is the part most often skipped.
- The core numbers are gas manifold pressure, gas input rate clocked at the meter, temperature rise across the heat exchanger, external static pressure, and a combustion and venting check.
- You should receive those readings in writing, along with the model and serial numbers, the permit information and the warranty registration confirmation.
- A homeowner can verify the paperwork, the vent terminations, the thermostat behaviour and the airflow room by room; the gas and combustion readings must be taken by a licensed gas technician.
- Commissioning is normally included in a proper installed price, not an add-on, and a quote that does not mention it deserves a direct question before you sign.
Commissioning is everything a licensed technician does after the new furnace is bolted in place and the gas and electrical connections are made: measuring the gas input rate, setting manifold pressure, measuring temperature rise across the heat exchanger, measuring external static pressure in the duct system, verifying combustion and venting, configuring the blower and thermostat, and then writing all of it down and handing it to you. An installation without commissioning is a box connected to your ducts and your gas line, running at whatever the factory defaults happen to be, in a house it has never been matched to. That distinction is not a detail. It decides whether the furnace runs at the efficiency you paid for, whether the heat exchanger sees the temperatures it was designed for, whether the warranty holds up, and whether you end up calling somebody back in November about cold rooms and short cycling. The good news is that commissioning is not mysterious, and most of what proves it happened is visible to you on the day, in the readings written on a sheet of paper and in a few things you can check yourself while the technician is still there.
What does commissioning actually mean on a new furnace?
Every gas furnace leaves the factory with default settings chosen to be safe in the widest possible range of houses. Your house is one specific house, with one specific duct system, one specific gas line length and diameter, one specific vent route, and one specific elevation. Commissioning is the process of moving the appliance from the factory default to the correct setting for your building, then proving with instruments that the result is inside the manufacturer’s published range.
There are three layers to it. First, verification: is the appliance installed the way the manufacturer’s instructions and the BC gas code require, with the right clearances, the right vent materials and lengths, the right condensate routing, the right gas line capacity and the right electrical supply. Second, measurement and adjustment: the technician takes readings, compares them to the ranges printed on the rating plate and in the installation manual, and adjusts until the appliance is inside them. Third, documentation and handover: the readings are recorded, the safeties are demonstrated, the thermostat is configured and explained, the filter size and location are shown to you, and the paperwork is completed.
That third layer is the one homeowners should insist on, because it is the only part that survives the day. Six months later, nobody remembers what the temperature rise was. A commissioning sheet remembers. If a warranty claim or a performance dispute ever comes up, the difference between a documented startup and a verbal one is enormous.
Which measurements should be taken before the installer leaves?
These are the readings that matter on a residential gas furnace. Every one of them requires a licensed gas technician with the correct instruments. None of them is optional on a new installation, and none of them can be estimated by eye or by ear. If your installer cannot tell you what these numbers were on your system, the appliance has not been commissioned, whatever else was done well.
Each manufacturer publishes its own acceptable ranges on the rating plate and in the installation manual, and those ranges differ by model, by stage and by altitude. Ask which range applied to your unit and ask where it is printed. A technician who is measuring properly will show you without hesitation.
| Measurement | Why it matters | Who may take it |
|---|---|---|
| Gas manifold pressure | Sets how much gas reaches the burners. Too high overfires the heat exchanger and shortens its life; too low causes poor flame quality and nuisance lockouts. | Licensed gas technician only |
| Input rate clocked at the gas meter | Confirms the furnace is actually burning the rated input rather than being assumed to. Catches undersized or overloaded gas piping. | Licensed gas technician only |
| Temperature rise across the heat exchanger | The single best indicator that airflow and firing rate are matched. Outside the published range, the heat exchanger is being stressed or the house is being starved of heat. | Licensed gas technician only |
| External static pressure in the duct system | Reveals whether your existing ducts, filter and coil can actually move the air this furnace needs. Often the reason a new furnace underperforms in an older house. | Licensed technician only |
| Combustion analysis and vent verification | Confirms clean, complete combustion and that flue gases leave the building safely by the correct vent material, length and termination. | Licensed gas technician only |
| Blower speed and staging configuration | Matches the fan to the duct system and the heating stages, and sets fan-on and fan-off timing for comfort. | Licensed technician only |
| Safety device verification | Proves the pressure switch, rollout switch, limit switch, flame sensor and condensate safety all shut the appliance down when they should. | Licensed gas technician only |
| Condensate drain and neutraliser check | A blocked or badly pitched condensate line is one of the most common early failures on a condensing furnace. | Technician sets it up; homeowner can inspect later |
What paperwork should I have in my hand at the end of the day?
A complete handover is short but specific. You should end the installation day with a written record you could hand to any other licensed contractor five years from now and have them understand exactly what was installed and how it was set.
If some of these are genuinely pending, that is normal and fine, but the installer should tell you which ones and when they will arrive. What should not happen is silence.
- The commissioning or startup readings, with the measured values and the manufacturer’s acceptable range beside them.
- Model number and serial number of the furnace, and of any coil, condensing unit or control installed with it.
- Permit information, including which authority the permit was taken with and how the inspection will be handled. Permit fees are set by each municipality or by Technical Safety BC, and your installer should tell you who holds the permit on your job.
- Confirmation that the manufacturer’s warranty has been registered in your name, plus a plain statement of what the labour coverage from the contractor is and how long it runs.
- The filter size, the filter location, the direction of airflow and how often it should be changed in your house.
- A written note of anything left incomplete or deferred, such as a duct modification agreed for later, and what it depends on.
- The contractor’s licence information. BC Wide holds TSBC licences LGA0090068 and CGA0028029, and any licensed contractor should give you theirs on request.
What does commissioning look like on a dual fuel system?
When a heat pump is added to a gas furnace, commissioning gets a second half, and it is the half most often rushed. The furnace still needs every reading listed above. On top of that, the heat pump and the controls need their own verification, because a dual fuel system is really two heating appliances sharing one duct system and one thermostat, and the value of the whole arrangement lives in the changeover logic.
The technician should confirm the refrigerant charge and line set by the manufacturer’s method, verify airflow across the indoor coil, and then set and demonstrate the balance point, meaning the outdoor temperature below which the system hands heating over from the heat pump to the gas furnace. They should show you how the thermostat displays which appliance is running, and what happens during a defrost cycle so the sound and the brief change in supply air temperature do not alarm you the first cold morning. Any electric backup element in the system should be identified and its role explained, because in a dual fuel arrangement the gas furnace is the intended backup for cold snaps, not the electric element.
Refrigerant work is legally restricted to certified technicians in Canada. A homeowner must never handle, top up or recover refrigerant, and there is no homeowner step in that part of the commissioning at all. What you can do is ask to see the readings and ask what balance point was set and why that number was chosen for your house.
What does this cost, and is commissioning a separate charge?
Commissioning should be inside the installed price, not a line item added later. It is the last third of the job, not an upgrade. Here are ballpark ranges for Greater Vancouver, installed, before GST, to give you orientation on what the work itself sits inside. A high-efficiency gas furnace replacement typically lands in the ballpark of $5,000 to $9,000, with complex jobs running higher.
Those are ballpark figures for orientation only. They are not a quote, and an accurate price for your home needs a site visit, because the variables below move the number far more than the badge on the furnace does.
Adding a heat pump to an existing gas furnace as a dual fuel system typically sits in the ballpark of $10,000 to $18,000, with an electrical panel upgrade extra when one is needed. Again, a wide honest range, not a number to hold anyone to. What matters more than the range is understanding what pushes a job toward the top of it.
Rebates, incentives, financing arrangements and any diagnostic or callout charges are described qualitatively here on purpose, with no figures attached, because those amounts change, vary by household and by programme, and are not something a general article can responsibly put a number on. Ask about them directly and get them in writing on your own quote.
- Venting: a condensing furnace needs its own vent route and termination, and cutting a new path through a finished basement or a tight side yard adds labour.
- Gas line sizing: older homes were often piped for smaller loads, and a longer or larger line may be required for the new appliance to reach its rated input.
- Condensate routing: a condensing appliance produces acidic condensate that must reach an approved drain, sometimes by way of a small pump and a neutraliser.
- Electrical: a dedicated circuit, a new disconnect, or on dual fuel jobs a panel assessment.
- Permits and inspection: taken with the municipality or Technical Safety BC depending on the work, and coordinated by the contractor.
- Access and removal: narrow stairs, crawlspaces, tight mechanical rooms and disposal of the old appliance all add time.
- Code upgrades uncovered on the day: combustion air openings, clearances, or an unsafe existing vent shared with another appliance.
Why does commissioning matter more in Metro Vancouver homes?
Our climate is mild and wet, and a furnace here spends most of the season in part load rather than flat out. That sounds forgiving, and in one sense it is, but it makes setup errors quieter and longer lived. A furnace that is overfired or fighting a restrictive duct system in Winnipeg announces itself quickly. Here it can limp along for years, cycling more than it should, wearing the ignition components and the heat exchanger, and simply feeling a bit off in the far bedroom, until one January cold snap makes it obvious.
The housing stock matters too. A great deal of Metro Vancouver is post-war and 1960s to 1980s construction with duct systems designed around older, lower-airflow equipment, plus finished basements that have been added to over decades. Dropping a modern high-efficiency furnace onto those ducts without measuring static pressure is where most disappointing installations begin. The furnace is fine. The system around it was never checked.
Strata and multi-family density brings its own constraints: shared walls, restricted vent termination locations, limited mechanical room space, and building rules about work hours and access. Those constraints should show up in the quote and in the commissioning plan, not as a surprise on the day. And because our incoming water is soft, hydronic and water heating problems in this region tend to be sludge and corrosion rather than hard-water scale, which changes what a technician should be looking at on the water side of a mechanical room.
Coastal damp also means crawlspaces and unconditioned basements are common, and duct leakage in those spaces quietly throws away the efficiency you just paid for. A thorough commissioning visit at least notes it, even when sealing the ducts is a separate conversation for later.
What can I verify myself while the technician is still here?
You cannot and should not take gas or combustion readings. Gas work and most electrical work is legally restricted to licensed trades in British Columbia, and that restriction exists for good reason. But there is a real list of things a homeowner can check without touching anything dangerous, and doing so politely at the end of the day is completely normal. Any competent installer expects it.
Walk it in this order while everything is still open and the crew is still on site.
- Ask for the startup readings and look at them. You do not need to interpret the numbers. You need to see that they exist and that each one has a manufacturer range beside it.
- Photograph the rating plate yourself, so you have the model and serial numbers independently.
- Look at the vent terminations outside. They should be firmly supported, clear of obstructions, not aimed at a window, walkway or gas meter, and not buried behind shrubs.
- Ask to watch a full cycle: a call for heat, ignition, the blower coming on, and the shutdown sequence with the fan-off delay.
- Feel the supply air at the register furthest from the furnace, and at one or two others. Grossly uneven delivery is worth raising now, not in December.
- Check the condensate line runs continuously downhill to its drain with no dips or kinks, and ask where the neutraliser is if one is fitted.
- Find the filter, confirm the size is written down for you, and confirm which way the arrow points.
- Confirm your carbon monoxide alarms are in place, and replace any that are past their stamped expiry date.
- Ask what the thermostat is set to do, including any fan mode and any staging behaviour, and ask to be shown the screen that tells you which appliance is running on a dual fuel system.
When should I call a licensed technician?
Call a licensed gas technician, not a handyman and not yourself, for anything involving gas, combustion, venting or refrigerant. That includes any adjustment to manifold pressure, any change to the vent, any relocation of the appliance, and any work on a shared flue. It also includes the entire commissioning process described on this page.
Call promptly after a new installation if you notice any of the following in the first weeks: the furnace short cycling, meaning it starts and stops repeatedly within a few minutes; a burning smell that persists past the first couple of cycles; water pooling near the appliance; a vent termination that has come loose or frosted over; rooms that are dramatically colder than before the replacement; or any carbon monoxide alarm activation at all.
If your carbon monoxide alarm sounds, or you smell gas, leave the building first and call from outside. That is not a service call to schedule around your week. Same-day attendance is often possible for urgent situations depending on the day and the crew’s position, and we will tell you honestly when it is and when it is not, but we will never promise you a guaranteed arrival window we cannot keep. For a gas smell, the priority is getting out of the building, not waiting by the phone.
If your system was installed some time ago and none of this was ever done, it is not too late. A licensed technician can commission an existing furnace: take the same readings, compare them to the rating plate, adjust what is adjustable and tell you plainly what is out of range and what it would take to correct. That visit often pays for itself in comfort alone, and it gives you the baseline document you should have received on day one.
What should I ask before I sign the quote?
The easiest time to get commissioning included is before any money changes hands. You do not need technical language. Four plain questions do the work, and the answers tell you a great deal about how the job will be run.
Ask them of everyone you are considering, including us. A contractor who answers these clearly and in writing is showing you how they operate. BC Wide is an independent TSBC-licensed contractor rather than a factory-authorised dealer, which means we service and install a range of brands and we will tell you plainly what we can and cannot stand behind on each one.
- Will you clock the gas input at the meter and measure temperature rise and static pressure, and will I get those numbers in writing?
- Who pulls the permit, which authority is it with, and how is the inspection handled?
- What happens if you open up the job and find the existing venting, gas line or ductwork needs work; how is that priced and approved before you proceed?
- Is the warranty registered in my name on the day, and what exactly does your own labour coverage include and for how long?
Frequently asked questions
Is commissioning included in the price of a new furnace, or is it extra?
It should be included in the installed price, because it is part of installing the appliance correctly rather than an upgrade to it. If a quote is silent about startup readings, ask directly whether they are included and whether you will receive them in writing. Getting that answer before you sign is much easier than getting it afterwards.
How long should commissioning take on a residential furnace?
The measuring, adjusting and handover portion typically takes a meaningful part of the afternoon after the physical installation is finished, and longer on a dual fuel system because the heat pump and changeover logic need their own verification. It is not a five-minute check that the flame lights. If the crew is packing up minutes after the furnace first fires, ask what was measured.
My furnace was installed last year and I never got any readings. What now?
A licensed technician can commission the system after the fact by taking the same measurements and comparing them to the rating plate and installation manual. They can adjust what is adjustable and document what is out of range and why. It gives you the baseline record you should have had originally, and it often explains comfort complaints that have been nagging since the install.
What is temperature rise, and why does everyone keep mentioning it?
Temperature rise is the difference between the air entering the furnace and the air leaving it, and every manufacturer prints an acceptable range for it on the rating plate. It is the quickest honest indicator that firing rate and airflow are matched to each other. A reading above the range usually means restricted airflow, and below it usually means the appliance is underfiring or moving too much air.
Does commissioning affect my manufacturer warranty?
It can. Manufacturers generally require that equipment be installed and set up in accordance with their published instructions, and an appliance running outside its documented ranges gives a manufacturer grounds to question a claim. Documented startup readings and a warranty registered in your name are the two pieces of paper that make a future claim straightforward rather than an argument.
My furnace is on a rental or contract arrangement rather than owned. Does any of this apply?
The technical standards are identical, because the appliance and the gas code do not care who owns the equipment. What differs is who is responsible for the work and who you call, and that is set out in your own rental agreement, so read it and use the number on your own bill for questions about your provider’s obligations. If you are considering replacing rented equipment with equipment you own, ask your provider in writing what your agreement requires before anything is removed.
What does a complete, honest quote for a furnace replacement look like?
It names the specific equipment by model, states clearly what is included, addresses venting, gas line, condensate and electrical rather than leaving them vague, says who pulls the permit, states the labour coverage and its duration, and explains how any conditions discovered during the work will be priced and approved before proceeding. It also gives a real total rather than a number that moves once work begins. You should be able to read it and know exactly what will be in your basement when the crew leaves.
BC Wide Home Services — Lower Mainland home-comfort specialists since 1999
Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.
Frequently asked questions
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
Are BC Wide technicians licensed and insured?
How can I book a service call?
Do you offer free estimates?
What brands do you service?
Do you offer government rebates for heat pumps?
How quickly can you replace a broken hot water tank?
Why should I choose BC Wide over other HVAC companies?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


