★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

What You Are Actually Paying For With a Triangle Tube Boiler

Boilers

What You Are Actually Paying For With a Triangle Tube Boiler
Home › What You Are Actually Paying For With a Triangle Tube Boiler

What You Are Actually Paying For With a Triangle Tube Boiler

Key takeaways

  • In a typical Metro Vancouver residential condensing boiler replacement, the appliance itself is usually the minority of the invoice; labour, venting, piping, controls, permits and site conditions make up the rest.
  • A ballpark installed range for a condensing gas boiler replacement in Greater Vancouver is roughly $7,000 to $15,000, and a gas combi boiler installation roughly $8,000 to $14,000 and up. These are ballpark figures for orientation only, not a quote.
  • Two licensed contractors can quote the same Triangle Tube model thousands apart without either being dishonest, because they are pricing different amounts of venting, gas line, electrical, condensate and distribution work.
  • Paying more genuinely buys correct sizing from a heat loss calculation, a proper vent route, adequate gas supply, real condensate neutralisation and a permitted, inspected job.
  • Paying more does not buy a better outcome when it is spent on oversizing, on controls nobody commissions, or on a bigger unit used to paper over undersized distribution.
  • BC Wide is an independent TSBC-licensed contractor (LGA0090068, CGA0028029). We install and service Triangle Tube equipment; we are not a factory-authorised dealer or warranty centre for any brand.

When you get a price for a Triangle Tube boiler in Metro Vancouver, most of what you are paying for is not the boiler. The appliance is a line item with a wholesale cost that does not vary much between licensed contractors buying through the same supply chain. What varies enormously is everything around it: the size and route of the new vent, whether the existing gas line can feed the input, whether the electrical supply and circuit are adequate, how condensate gets to a drain and gets neutralised, how much near-boiler piping and control wiring has to be rebuilt, how hard the old unit is to get out of the house, whether the distribution system needs changes, and the permit and inspection work. In a typical residential condensing boiler replacement, the equipment is commonly the minority of the invoice. That is why two honest, licensed contractors can look at the same Triangle Tube model and land thousands of dollars apart: they are pricing different amounts of work on your particular house, not different amounts of honesty.

What does a Triangle Tube boiler installation actually cost in Metro Vancouver?

A ballpark installed range for a condensing gas boiler replacement in Greater Vancouver is roughly $7,000 to $15,000 before GST. These are ballpark figures for orientation only. They are not a quote, and an accurate price needs a site visit, because the number depends far more on your mechanical room than on the model on the box.

If you are replacing a boiler and a separate tank water heater with a single combi appliance that makes both heat and domestic hot water, a ballpark installed range is roughly $8,000 to $14,000 and up. The open-ended top end is honest rather than evasive: combi work adds domestic water piping, sometimes a recirculation strategy, and often a larger gas load, and those three things are where combi jobs in older Metro Vancouver housing get expensive.

Notice how wide both ranges are. Any contractor who gives you a firm number over the phone for a boiler they have not seen the room for is guessing, and that guess will either be padded to protect them or corrected upward later. A written quote after a site visit is the only number worth comparing.

Rebates and incentive programs, permit fees, financing and future tune-up or service-call charges are all real line items, but we deliberately attach no dollar figure to any of them here. Rebate values change, permit fees are set by each municipality or by Technical Safety BC, and financing terms depend on the lender. Ask for each of those separately and in writing.

How much of the price is the boiler and how much is the installation?

Think of the invoice as five buckets. The appliance is one of them, and in most residential replacements it is not the biggest. The other four are materials around the boiler, labour, compliance, and site conditions. Triangle Tube, like any manufacturer, sets a wholesale structure; a licensed contractor’s margin on the appliance is a normal part of business and is rarely where quotes diverge.

Where quotes diverge is in the scope each contractor has written down. One may have priced a new stainless vent through an exterior wall with the correct clearances; another may have assumed the existing chimney liner can be reused, which for a condensing appliance it generally cannot. One may have included upsizing the gas line from the metre; another may have assumed the existing line is adequate without measuring the total connected load. Those are scope differences, not integrity differences, and the fix is to make both contractors itemise.

Ask each quote to break out, at minimum: appliance and any factory accessories, venting materials and labour, gas piping, electrical work, condensate handling and neutralisation, near-boiler piping and pumps, controls and thermostat, removal and disposal of the old unit, permit and inspection, and commissioning. If a quote is a single number with no breakdown, you cannot compare it to anything.

Cost bucketWhat it coversWhy it varies between quotes
ApplianceThe Triangle Tube boiler itself plus factory accessories such as sensors, kits or a low-loss headerModel and output selected, and which accessories are treated as included rather than optional
VentingIntake and exhaust piping, terminations, clearances, penetrations, patchingRoute length, number of elbows, whether the run goes through a wall or up through the roof, and whether an old chimney is abandoned
Gas supplySizing, upsizing or re-routing the gas line to meet the appliance input plus all other connected appliancesDistance from the metre, existing pipe size, and total load once a combi or a second appliance is added
Electrical and controlsDedicated circuit, disconnect, low-voltage wiring, outdoor sensor, zone controls, thermostatPanel capacity, whether a new circuit is needed, and how many zones are being rebuilt
CondensateDrain routing, trap, neutraliser, and a pump when gravity drainage is not availableWhere the nearest suitable drain is and whether the boiler sits below it
Near-boiler pipingPrimary and secondary piping, pumps, air and dirt separation, expansion tank, isolation valvesCondition of existing piping and whether the system is being properly separated and cleaned
Removal and accessDemolition, draining, getting the old unit out and the new one inCrawl space, tight stairs, strata corridors, parking and elevator access
CompliancePermit application, inspection coordination, gas and electrical sign-off, documentationMunicipality and scope; fees are set by the authority, not by the contractor

Why do two licensed contractors quote the same Triangle Tube boiler so differently?

The single most common reason is that one quote includes work the other has excluded, and you have not been shown the exclusions. Venting is the classic example. A condensing boiler produces cool, wet flue gas that a masonry chimney was never designed for, so it needs its own sealed vent system in an approved material, run within the manufacturer’s published limits for length and fittings. If your mechanical room sits in the middle of the house, that vent may have to travel a long way to a legal termination point, past clearances to windows, doors, decks and property lines. One contractor prices that route honestly; another assumes a shorter route that turns out not to be permissible.

The second reason is gas supply. Adding a modulating condensing boiler, or converting to a combi, can raise the peak gas demand of the house. The line has to be sized for the total connected load over its actual length, not for the boiler in isolation. If the existing line is undersized, somebody has to pay to upsize it. A ballpark range for a new or upsized gas line to an appliance is roughly $500 to $1,500 where the run is short and accessible, and roughly $1,500 to $3,000 and up where it is long, buried, or through finished space. Again, ballpark only, not a quote.

The third reason is what each contractor plans to do with your existing distribution. A boiler is only the heat source. If half the radiators are airbound, the circulator is failing, the expansion tank is waterlogged or the system is full of sludge, one contractor will include flushing, air and dirt separation and a new expansion tank while another will connect the new boiler to the old mess and hand you the consequences.

The fourth reason is sizing itself. A contractor who performs a heat loss calculation will often specify a smaller output than a contractor who sizes by replacing like for like. Smaller usually costs less and, on a modulating condensing boiler, usually performs better. Ask both quotes what heat loss number they used and how they arrived at it.

Where does paying more genuinely buy you something?

There are parts of a boiler job where spending more returns real value over the fifteen or twenty years you will own the system, and it is worth knowing which ones they are.

It is also worth saying what you are not buying. You are not buying a factory relationship. BC Wide is an independent TSBC-licensed contractor; we install and service Triangle Tube equipment, we are not a factory-authorised dealer, distributor or warranty centre for Triangle Tube or any other brand. A contractor who implies otherwise is telling you something about their marketing, not about the quality of the install.

  • A heat loss calculation instead of like-for-like sizing. Correct sizing lets a modulating boiler run long, low, condensing cycles instead of short-cycling, which is the difference between the efficiency on the rating plate and the efficiency you actually get.
  • A properly engineered vent route with the correct material, support, slope and termination clearances, inspected and signed off, rather than the shortest route somebody could get away with.
  • Gas line sizing calculated for the whole house’s connected load, so the boiler is not starved during a cold snap when the furnace, range and water heater are all calling.
  • Real condensate handling: a trap, a neutraliser that gets serviced, and a drain route that will not freeze or back up. Condensate from a condensing appliance is acidic and should not simply be dumped at a fitting.
  • Hydraulic separation, air and dirt separation, and a system flush. Metro Vancouver water is soft, so the enemy in a hydronic system here is sludge and corrosion rather than limescale, and magnetite sludge is what kills pumps and plugs heat exchangers.
  • Commissioning: combustion analysis, setting the curve and the outdoor reset, verifying the domestic hot water settings on a combi, and leaving you documentation of what was set and why.
  • A permit and an inspection. This is the part homeowners are most often tempted to skip, and it is the part that protects the resale of your home and your insurance position.

Where does paying more buy you nothing?

Not every upcharge earns its place, and a good contractor will talk you out of some of them.

Oversizing is the most expensive mistake in residential hydronics. A larger Triangle Tube boiler costs more, vents no better, and on an undersized emitter system it simply short-cycles harder. Bigger output does not fix a distribution problem; it hides it badly. If your rooms are cold, the answer is usually radiator or loop capacity, circulator selection, balancing or air removal, not a larger heat source.

Zone controls and outdoor reset that nobody commissions are also money with no return. The controls on a modern modulating boiler only pay for themselves if someone sets the heating curve to your building, verifies it over a season and explains it to you. Ask whether commissioning is included and what it involves.

Extended parts coverage should be read before it is bought. Terms differ by product, by who registers it and by whether the install was permitted, and durations change over time. Do not accept a verbal claim about warranty length from anyone, including us. Read the manufacturer’s own printed terms for your model, and ask what labour coverage the contractor provides separately.

Finally, be sceptical of any sizing, efficiency or output figure quoted to you from memory. The numbers that matter appear on the appliance rating plate, in the manufacturer’s installation manual for your exact model, and on your written quote. If a figure is being used to justify a price, ask to see it in one of those three places.

What does Metro Vancouver specifically add to a boiler price?

Our climate is mild and wet rather than severely cold, which matters more than homeowners expect. Design temperatures here are moderate, so heat loss calculations often justify smaller boilers than the one being replaced. A long, mild shoulder season also means your boiler spends most of its operating hours at part load, which is exactly where a modulating condensing appliance earns its efficiency, and exactly where an oversized one wastes it.

Our water is soft. In a closed hydronic loop that means limescale is not the story; sludge, magnetite and oxygen corrosion are. Budget for proper air and dirt separation and a system clean on a retrofit, and treat any quote that skips them as incomplete rather than cheap.

Our housing stock is the real cost driver. Older Vancouver, Burnaby and New Westminster homes were often piped and vented for atmospheric appliances into masonry chimneys, with gas lines sized for a smaller load and mechanical rooms in crawl spaces or basements with awkward access. Converting that to a sealed, direct-vent condensing installation is genuine work. In strata buildings and townhomes, add access rules, parking and elevator booking, restrictions on exterior penetrations, and the need for strata approval for anything that changes the building envelope. None of that shows up as a bigger boiler, but all of it shows up in labour hours.

Permits and inspection are handled locally. Gas work requires a licensed gas fitter and a permit, and fees are set by each municipality or by Technical Safety BC rather than by the contractor. Ask who pulls the permit and whether the fee is passed through at cost. A quote that quietly omits the permit is not cheaper; it is smaller in scope.

How do you compare two boiler quotes fairly?

Comparing quotes is not about finding the lowest total. It is about making the two documents describe the same job, then seeing which contractor you would rather have in your mechanical room.

Work down a list like this, and put both quotes side by side against it. If one quote is silent on a line, that is your first question.

  • What output was specified, and what heat loss calculation produced it?
  • What vent material and route is included, and does the price include exterior patching and making good?
  • Has the gas line been sized for the total connected load, and is any upsizing included or excluded?
  • Is a dedicated electrical circuit needed, is it included, and does the panel have capacity?
  • How is condensate drained and neutralised, and is a condensate pump included if gravity will not work?
  • Does the price include flushing the system, air and dirt separation, a new expansion tank and isolation valves?
  • Is removal and disposal of the old appliance included?
  • Who pulls the permit, and is the fee passed through at cost?
  • What does commissioning include, and will you receive written settings and documentation?
  • What is covered on parts by the manufacturer for that specific model, and what labour coverage does the contractor add?

When should you call a licensed technician instead of investigating yourself?

In British Columbia, gas work and most electrical work are legally restricted to licensed trades. As a homeowner you may safely read the rating plate, note the model and serial number, photograph the mechanical room and the vent termination, check the system pressure gauge, look for visible leaks or staining, confirm the thermostat is calling, and check whether a switch or breaker has been turned off. You may bleed a radiator on a conventional system if you know how and are comfortable doing it.

You may not open the sealed combustion chamber, alter gas piping, change a gas valve, adjust combustion or gas pressures, modify or extend venting, or wire the boiler. Those are gas fitter and electrician work, and doing them yourself puts your insurance, your permit history and your household at risk.

Call a licensed technician immediately if you smell gas, if a carbon monoxide alarm sounds, if you see soot or scorching around the appliance or vent, if the boiler locks out repeatedly, if the relief valve is discharging, or if you find water or flue gas where it should not be. Leave the building and call from outside if you smell gas or suspect combustion products are entering the house.

If you are pricing a Triangle Tube boiler replacement in Metro Vancouver and want the scope written out line by line so you can compare it properly, call BC Wide at (604) 473-9690. We will tell you plainly which parts of your quote are the appliance and which parts are your house. Same-day attendance is sometimes possible depending on the day and the crew’s existing bookings, and we will tell you honestly when it is not rather than promise an arrival window we cannot hold.

Gas & carbon-monoxide safety: Gas appliances produce carbon monoxide, an odourless gas that can be fatal. Every home with a gas boiler, furnace, water heater or fireplace should have working CO alarms on each sleeping level, tested regularly and replaced at the interval printed on the unit. If you smell gas, hear a hissing near gas piping, or a CO alarm sounds, leave the building first and then call from outside. Never operate a boiler with visible soot, scorching, a disconnected or damaged vent, or a relief valve that is discharging. In British Columbia, gas fitting and most electrical work are restricted to licensed trades: never alter gas piping, gas valves, combustion settings or venting yourself. BC Wide is a TSBC-licensed contractor, licences LGA0090068 and CGA0028029.

Frequently asked questions

Is a Triangle Tube boiler more expensive to install than other brands?

The installation work is essentially brand-neutral. Venting, gas sizing, condensate, electrical, near-boiler piping, permits and access are driven by your house, not by the badge on the appliance. Appliance costs differ between brands, but in a typical residential replacement the appliance is usually the minority of the invoice, so brand choice moves the total far less than site conditions do.

Why is the quote so much higher than the price I found for the boiler online?

Because the online price is the appliance alone, with no vent system, no gas piping, no electrical, no condensate neutralisation, no near-boiler piping, no permit, no inspection, no commissioning and no labour. It also carries no warranty position, since manufacturer terms commonly depend on a licensed, permitted installation. The gap between that price and a quote is the job itself.

Can my existing chimney be reused for a new condensing boiler?

Generally no. A condensing appliance produces cool, acidic flue gas that a masonry chimney was not designed to handle, so these boilers use their own sealed direct-vent system in an approved material, run within the manufacturer’s published limits. Any quote that assumes the chimney can be reused should be questioned, and the old chimney usually has to be properly abandoned or dealt with as part of the work.

Do I need a permit to replace a boiler in Metro Vancouver?

Gas work requires a licensed gas fitter and a permit, and the installation is inspected. Fees are set by each municipality or by Technical Safety BC rather than by the contractor. Ask who pulls the permit and whether the fee is passed through at cost, and keep the documentation, since it matters at resale and to your insurer.

Should I get a bigger boiler so the house heats up faster?

Usually not. Oversizing costs more up front and makes a modulating condensing boiler short-cycle, which reduces both efficiency and component life. If rooms heat slowly, the limitation is more often the distribution side: emitter capacity, circulator selection, balancing, air in the loops or sludge. A heat loss calculation, not a bigger appliance, is the right starting point.

Is BC Wide an authorised Triangle Tube dealer?

No. BC Wide is an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029. We install and service Triangle Tube equipment as an independent contractor; we are not a factory-authorised dealer, distributor or warranty centre for Triangle Tube or any other brand. For manufacturer warranty terms on a specific model, read the manufacturer’s own printed documentation.

What should I do before a contractor comes to quote?

Photograph the existing boiler’s rating plate, the mechanical room including the vent and gas connections, and the outside wall or roof where any vent terminates. Note whether you have radiators, baseboard or in-floor loops, roughly how many zones, and whether your hot water comes from the boiler or a separate tank. If you live in a strata, check the rules on exterior penetrations and access before the visit.

Are the ranges in this article a quote?

No. Every figure here is a ballpark range for orientation only, given so you can tell whether a quote is in a plausible neighbourhood. Real pricing requires a site visit, because venting route, gas line capacity, electrical, condensate routing, access and distribution condition are what set the number. Call (604) 473-9690 for a written quote after an assessment.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote