★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Will a Conversion Affect Your Home Insurance?

Furnace

Will a Conversion Affect Your Home Insurance?
Home › Will a Conversion Affect Your Home Insurance?

Will a Conversion Affect Your Home Insurance?

Key takeaways

  • A conversion rarely changes your premium on its own, but an undocumented or unpermitted one can create a coverage problem if a claim is ever made.
  • Insurers care most about three things: who did the work, whether it was permitted and inspected, and whether anything unsafe was left behind.
  • Tell your insurer before the work starts and again when it finishes, and send the permit and inspection records with the invoice.
  • An abandoned or oversized chimney left in place after a conversion is the single most common safety and insurance loose end.
  • Strata owners have a second approval layer, and the strata corporation’s own policy has nothing to do with your unit owner’s policy.
  • If your existing appliance type still suits the house, a like-for-like replacement is simpler, cheaper to document and rarely raises an insurance question at all.

Changing the type of heating or hot water system in your home can affect your home insurance, but usually not through the premium. What actually changes is the documentation your insurer expects to see: proof that the work was done by licensed trades, that a permit was pulled where the municipality requires one, and that nothing was left behind in an unsafe condition. A properly permitted, inspected and documented conversion is normally a neutral event on your policy, and in some cases it works in your favour because newer equipment with modern safety controls presents less risk than what it replaced. An undocumented conversion is the one that causes trouble, and it tends to cause it at the worst possible moment, which is during a claim. This page explains what insurers look at, how to work out where your own house sits, and what to send them once the job is done.

Will changing my heating system type change my premium?

In most residential cases, no. Home insurance in British Columbia is priced mainly on the building itself, its age, its location, its construction, its claims history and the replacement value of the structure and contents. The heating appliance is one input among many, and swapping one type of gas appliance for another, or adding a heat pump paired with a gas furnace as backup, is not usually the kind of change that moves a premium up or down on its own.

What a conversion does change is the description of the risk on file. Your policy was written against a house with a particular system in it. When the system type changes, the file should change too. Insurers ask about heating type on the application for a reason, and an answer that was accurate when you signed can quietly go stale after a conversion. Keeping the file current is the whole job, and it costs nothing but a phone call and an email with attachments.

There is a second, quieter effect worth knowing about. Some insurers treat newer, sealed-combustion equipment with modern safety controls more favourably than older atmospheric equipment, simply because the failure modes are better managed. Others do not differentiate at all. You will not know which camp your insurer is in until you ask, and asking is free.

What does an insurer actually care about after a conversion?

Insurers are not evaluating your taste in equipment. They are evaluating whether a foreseeable loss became more likely because of the change. In practice that reduces to a short list of questions, and every one of them is answerable with paperwork you should already have.

  • Who performed the work. Gas fitting in BC is restricted to licensed gas fitters working under a licensed contractor, and most electrical work is restricted to licensed electricians. Work outside those restrictions is the clearest way to create a coverage argument.
  • Whether a permit was pulled. Gas permits are issued through Technical Safety BC or through a municipality that administers its own gas permitting, and electrical and building permits come from your municipality. The permit is the record that the work was declared and inspected.
  • Whether the installation passed inspection, and whether any deficiencies noted at inspection were corrected and signed off.
  • Whether anything was abandoned rather than removed or made safe. A disused chimney, a capped but live gas branch, or a redundant vent connector left dangling in a furnace room are all the kind of loose end that gets photographed during a loss investigation.
  • Whether the change altered the occupancy or use of the building, for example by converting part of the house into a suite at the same time. That genuinely does affect a policy and must be declared separately.

Which conversions raise questions and which do not?

It helps to separate the change itself from the knock-on work the change forces. The conversion is rarely the risk. The work it drags along with it is where the exposure lives, and that is what the table below is really describing.

Type of changeWhat the insurer usually asksWhere the real risk sits
Gas furnace replaced with a newer gas furnace of the same venting categoryLittle or nothing beyond a note on fileAlmost none if permitted and inspected
Gas furnace replaced with a condensing gas furnacePermit, inspection, what happened to the old chimneyThe chimney the old appliance shared, and the new condensate drain
Gas furnace plus a heat pump added as a dual-fuel systemPermit, electrical permit, equipment descriptionElectrical capacity, outdoor unit mounting, control changeover setup
Gas boiler and hydronic heating replaced with a ducted gas furnacePermit, inspection, confirmation the old system was decommissionedPiping left in place, new ductwork routes, combustion air
Gas tank water heater replaced with gas tanklessPermit, inspection, venting and gas line changesGas line and meter capacity, new sidewall vent, condensate
Any gas appliance moved to a new location in the housePermit, inspection, floor plan changeNew venting route, combustion air, clearances to combustibles
A gas fireplace added where none existedPermit, inspection, chimney or vent detailsVenting, clearances, and the finish materials around the opening

What paperwork should I send my insurer?

Call your broker or insurer before the work starts, describe what you intend to change and ask directly whether they need anything specific. Write down who you spoke to and when. Then, once the job is finished and signed off, send a short email with the documents attached. Keep a copy of that email; it is your proof the disclosure happened.

The package is short. The contractor invoice showing the licensed contractor name and licence numbers, the equipment make and model as installed, the permit number, and the inspection result or certificate of acceptance where one was issued. If the conversion involved abandoning a chimney, add a line describing what was done to it. If an electrical permit was pulled, include that too.

Photographs are worth more than people expect. A clear photo of the finished appliance, its vent termination outside, the gas shutoff and the electrical disconnect gives an adjuster a picture of a properly executed job and closes off a lot of speculation before it starts.

What knock-on work does a conversion actually involve?

This is the part homeowners underestimate, and it is the part that determines whether a conversion is a reasonable project or the wrong answer entirely. Nothing below is optional, and each item is a place where an unpermitted shortcut becomes a hazard.

  • Venting category and route. Older mid-efficiency appliances commonly vent into a masonry or metal chimney. Condensing appliances vent through plastic pipe out a sidewall, on a route that must respect clearances to windows, doors, air intakes, meters and the property line.
  • Combustion air. A gas appliance needs a supply of air to burn safely. Change the appliance type or tighten up the house around it and the existing provision may no longer be adequate.
  • Gas line and meter capacity. A tankless water heater or a larger appliance can demand more gas at once than the existing branch or the meter can deliver. Undersized gas piping is a real and common blocker in older Metro Vancouver housing, and it is not something you can eyeball.
  • Electrical capacity. Adding a heat pump to sit alongside a gas furnace means new circuits, a disconnect, and an honest look at whether the existing service can carry it.
  • Condensate drainage and neutralisation. Condensing appliances produce acidic condensate that needs a proper, protected drain path, and in many installations a neutraliser.
  • Chimney lining or abandonment. If the furnace leaves the chimney, whatever remains connected to that chimney, such as a water heater, may now be venting into a flue far too large for it. That is the orphaned appliance problem, and it is a genuine carbon monoxide hazard, not a technicality.
  • Distribution. Ducts sized for the old appliance, or hydronic piping laid out for a different heat source, may not suit what replaces it. A system that cannot move the heat it makes will run badly no matter how good the box is.
  • Permits, inspection, and where applicable strata or municipal approval for exterior changes such as a vent termination or an outdoor unit.

When is a conversion the wrong answer?

Plenty of the time. If your existing appliance type still suits the house, converting is a way of buying a long list of secondary work in order to arrive at roughly the same comfort you already had. A like-for-like replacement, done properly, is faster, simpler to document, and raises no insurance question worth the name.

Be sceptical of a conversion when the gas service or meter cannot carry the new load without an upgrade you have no other reason to do, when there is no practical sidewall vent route that meets clearances, when the electrical service is already near its limit and the conversion is not itself the reason to upgrade it, when the distribution system would need to be rebuilt to suit the new appliance, or when a strata will not approve the exterior work the conversion requires. Any one of those turns a tidy project into a large one.

A conversion earns its keep when it solves a problem you actually have. A chronically undersized water heater, a boiler at the end of its life in a house that is being re-ducted anyway, a furnace room being relocated during a renovation, or the decision to add a heat pump alongside the gas furnace so the house has a milder-weather option with gas backup for the cold snaps. Those are reasons. Novelty is not.

Does anything about this work differently in Metro Vancouver?

Yes, in three practical ways. The first is our housing stock. A great deal of Burnaby, Vancouver, New Westminster, Coquitlam, Richmond and the North Shore is older, and older houses were built around chimneys and around gas piping sized for the appliances of the day. Conversions in that stock run into venting routes and gas capacity far more often than they run into anything else.

The second is strata density. A large share of Metro Vancouver homes are in strata buildings, and a strata owner faces two approval processes rather than one. The strata corporation controls common property, which typically includes exterior walls, roofs and often the chimney and vent terminations, so an alteration agreement is usually required before a vent can be cut through a wall or an outdoor unit mounted. It is also worth being clear that the strata corporation’s own insurance policy and your unit owner’s policy are separate things. Disclosing your conversion to the strata does not disclose it to your insurer, and the reverse is equally true.

The third is our climate. Mild, wet and coastal means the heating season is long and gentle rather than short and brutal, which is exactly why a heat pump paired with a gas furnace as backup suits this region so well: the heat pump handles the long mild stretch, and the gas furnace is there for the cold snaps and for the days when the outdoor coil is working hardest. Our water is soft, so hydronic systems here fail through sludge and corrosion rather than limescale, and a conversion that abandons an old hydronic loop should deal with that loop properly rather than leaving stagnant water in it.

When should I call a licensed technician?

Before the conversion, to find out whether it is even practical. A site visit that checks the vent route, the gas line and meter capacity, the combustion air provision, the electrical service and the existing distribution will tell you in an afternoon whether this project is a straightforward one or a large one. That is a far better use of a day than discovering a blocker halfway through.

During and after, because most of the work is legally restricted. In British Columbia, gas fitting must be carried out by a licensed gas fitter working under a licensed gas contractor, and most electrical work must be carried out by a licensed electrician. A homeowner may reasonably clear the working space, arrange access, handle their own paperwork with the insurer and the strata, keep filters and returns clean, and test the carbon monoxide alarms. A homeowner may not connect gas piping, alter venting, or make the appliance’s electrical connections.

Call immediately, rather than scheduling, if you smell gas, if a carbon monoxide alarm sounds, if an appliance that vented into a chimney is now spilling combustion products back into the room, or if you find soot, rust streaking or a scorched appearance around a vent connector. Same-day attendance is often possible in Metro Vancouver, and we will tell you honestly when it is and when the next available slot is instead of promising an arrival window we cannot keep. BC Wide Home Services Ltd is an independent TSBC-licensed contractor, licences LGA0090068 and CGA0028029, serving Metro Vancouver since 1999. Call (604) 473-9690 to book an assessment or to get a written quote for the work.

Gas & carbon-monoxide safety: Gas and carbon monoxide safety comes before any insurance question. If you smell gas, do not operate switches, phones or appliances inside the building; leave, take everyone with you, and call from outside. Install working carbon monoxide alarms on every level of the home, including outside sleeping areas, and test them on a schedule. Conversions create a specific hazard worth naming: when one appliance stops using a shared chimney, any appliance left connected to that chimney may now be venting into a flue far too large for it, which can cause combustion products to spill back into the house. That condition must be assessed and corrected by a licensed gas fitter, not left to chance. Gas fitting and most electrical work are legally restricted trades in British Columbia. Refrigerant work is restricted to certified technicians, and no homeowner should ever handle, add or recover refrigerant.

Frequently asked questions

Do I have to tell my insurer I converted my heating system?

Yes. Your policy was written against a description of the building that included its heating type, and you are expected to keep that description accurate. Tell them before the work starts and again when it is finished. The call is short and it protects you if a claim is ever made.

Can an insurer deny a claim because of an unpermitted conversion?

An insurer can raise the question, and that alone is enough to slow or complicate a claim badly. Unpermitted work by unlicensed people on restricted trades is the scenario that causes real problems, particularly if the loss is related to the appliance. A permitted, inspected, properly invoiced job closes that door before it opens.

Will adding a heat pump alongside my gas furnace affect my policy?

Usually only as a change of description rather than a change of price. A dual-fuel system keeps the gas furnace as backup for cold snaps, so the heating risk profile of the house is not dramatically different. Send your insurer the permit, the electrical permit and the equipment details so the file is current.

What happens to my old chimney after a conversion?

It must be dealt with deliberately, not ignored. Depending on what else is connected to it, the correct answer is relining to suit the remaining appliance, properly abandoning and capping it, or removing it. An orphaned appliance venting into an oversized flue is a carbon monoxide risk, and it is one an adjuster will notice.

Does my strata’s insurance cover my conversion?

No. The strata corporation’s policy covers the building and common property under the terms the corporation has arranged, and it is not a substitute for your own unit owner’s policy. You still need your strata’s written approval for any alteration affecting common property, such as a vent termination or an outdoor unit, and you still need to tell your own insurer.

Is a like-for-like replacement easier to insure than a conversion?

It is simpler to document, which amounts to the same thing in practice. Replacing a gas furnace with a comparable gas furnace changes very little about the description of the risk. If your current appliance type still suits the house, that is often the better project regardless of insurance.

What documents should I keep after the work is done?

Keep the contractor invoice showing the licensed contractor name and licence numbers, the make and model of the equipment installed, the permit number, the inspection result, and a few clear photos of the finished installation and its vent termination. Store them with your policy documents rather than in a drawer. If you ever claim, that small file does most of the work for you.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.
Are BC Wide technicians licensed and insured?
Yes. BC Wide holds a TSBC gas-fitting licence, our technicians are Red Seal certified for HVAC and gas, and we carry full liability insurance and WorkSafeBC coverage.
How can I book a service call?
Call (604) 473-9690, email info@bcwide.ca, or use the booking form on bcwide.ca. Most calls are answered the same business day and we offer next-day appointments for non-emergency work.
Do you offer free estimates?
Yes. Free in-home estimates are provided for boiler, furnace, heat pump and water-heater replacements. Diagnostic visits for repairs carry a flat service fee that is credited toward the repair if you proceed.
What brands do you service?
We service all major brands including Viessmann, Navien, IBC, Rinnai, Rheem, Bradford White, Weil-McLain, Laars, Baxi, NTI, Lennox, Carrier, Bryant, Goodman, Trane, York, Daikin, Mitsubishi Electric, AO Smith, Bosch, Noritz, Giant, GSW, John Wood, and Valor.
Do you offer government rebates for heat pumps?
Yes. We are a registered contractor for BC Hydro, FortisBC and federal Greener Homes rebates. A high-efficiency heat pump installation can qualify for up to $11,000 in combined rebates depending on your home and income.
How quickly can you replace a broken hot water tank?
Standard 40 or 50-gallon gas or electric tanks are typically replaced same-day or next-day from stock. Tankless water heaters and larger commercial units usually take 1–3 business days depending on parts availability.
Why should I choose BC Wide over other HVAC companies?
BC Wide Heating & Air Conditioning has been operating in Greater Vancouver since 1999 as a TSBC-licensed (LGA90068) HVAC and gas contractor. We specialise in furnaces, boilers, heat pumps and water heaters across every major brand, we give honest options instead of upselling, and our work is performed by experienced, certified staff — not subcontractors.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote