On a York furnace, 6 flashes points to flame loss: the burners lit, then the control lost the flame signal, often more than once in a single heating cycle (confirm against the manual for your unit). Expect the furnace to start, shut off, retry and sometimes lock out, leaving the house cold. Check the filter, thermostat, power switch and that the outdoor vent pipes are clear, reset once only if your manual allows it, then call a licensed gas technician. BC Wide serves Greater Vancouver at (604) 473-9690.
If your York furnace is showing 6 flashes (Flame loss / repeated flame dropout), here’s exactly what it means and what to do. This guide is part of our full York furnace error code list.
Severity: Needs attention.
What 6 flashes means on a York furnace
Flame was established but then lost, often repeatedly, during a heating cycle.
Common causes
- Weak flame sensing (dirty/positioned flame sensor)
- Marginal gas supply or pressure
- Burner or orifice fouling
- Condensate or venting issue disturbing the flame
- Flame rollout or pressure-switch interaction
What you can safely check first
- Replace a dirty air filter
- Outside, confirm the vent/intake terminations are clear
- Do not attempt burner, gas, or flame-sensor service — call a professional
Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.
When to call a technician
This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a York furnace usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.
BC Wide Heating & Air Conditioning has serviced Greater Vancouver furnaces since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.
York furnace repair across Greater Vancouver
If a York furnace showing 6 flashes won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast furnace repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.
Related York furnace codes
- York furnace Steady ON — Normal operation
- York furnace LED OFF — No power to control / control failure
- York furnace Rapid continuous flash — Line-voltage polarity reversed / grounding issue
- York furnace 2 flashes — External lockout (retries exhausted)
- York furnace 3 flashes — Pressure switch / draft fault
- York furnace 4 flashes — High-limit / temperature limit open
Frequently asked questions
Is 6 flashes on a York furnace serious?
It signals a fault to address; left alone it can lead to a no-heat shutdown. BC Wide repairs York furnaces 7 days a week across Greater Vancouver.
How do I reset a York furnace after 6 flashes?
You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.
York Furnace Error Code 6 Flashes: what it means for your heat and your safety
In plain terms, 6 flashes tells you the furnace gets as far as lighting the burners but cannot keep them lit. The control board watches for proof of flame the whole time the gas valve is open. When that proof disappears, the board shuts the gas off within moments, waits, and tries again. After several failed attempts in a row it can stop trying altogether and lock out. The meaning on this page, flame loss or repeated flame dropout, is how the code is commonly documented for York furnaces; confirm against the manual for your unit, because the label inside the blower door is the final word for your model.
For you, that shows up as heat that comes and goes. The house slowly loses temperature even though the thermostat is calling, and the furnace sounds busy without getting anywhere. If your hot water comes from a separate gas water heater, it is not affected by this code, because that appliance has its own burner and controls. The safety side matters more than the comfort side: each shutdown is the furnace protecting you, since gas is never left flowing without a flame. What deserves attention is the reason the flame keeps dropping, because some of those reasons involve venting and combustion air. Here is how owners usually describe it to us:
- The furnace lights, runs for a short while, then the burners go out and the blower keeps going.
- You hear the igniter or the click of the gas valve over and over during one heat call.
- Air from the vents turns lukewarm or cool even though the thermostat says heat is on.
- The house holds temperature on a mild day but falls behind on a cold evening.
- A small window in the blower door shows a light blinking six times, pausing, then repeating.
- The furnace eventually goes quiet and will not try again until the power is cycled.
- Gas and carbon monoxide safety: if you smell gas (a rotten-egg or sulphur odour) or a carbon monoxide alarm sounds, do not reset the furnace and do not touch switches or the thermostat. Leave the home with everyone, including pets, and call FortisBC’s emergency line or 911 from outside. Every home with a gas furnace should have working CO alarms near the sleeping areas.
York furnace 6 flashes causes, most common first, and the check you can make for each
These are the causes we find most often behind a 6-flash flame-loss code, roughly in the order we meet them in Greater Vancouver homes. Each one has a small owner-safe check. None of the checks involve opening the burner compartment, the gas valve or the control board.
A few cautions on the checks themselves. If you find the manual gas valve beside the furnace closed and you do not know who closed it or why, leave it closed and call; someone may have shut it for a good reason. Clear outdoor terminations by hand only, standing on the ground, and never push anything into the pipe. At the thermostat, make sure it is set to heat, the set point is above room temperature, and the batteries are fresh if it uses them. Confirm the furnace service switch, which often looks like a light switch on or near the unit, is on.
On resets: if your owner manual describes a reset, do it once. Turn the thermostat down, switch the furnace off at its service switch for about a minute, switch it back on and raise the thermostat. If the furnace runs a full cycle and holds, keep an eye on it and book a check anyway, because flame-loss faults rarely fix themselves. If the 6 flashes come back, stop there. Repeated resets keep sending gas to a burner that cannot hold a flame, and they can mask a venting fault that matters for carbon monoxide.
What a homeowner should never do: open the burner or control compartment, sand or remove the flame sensor, jumper or bypass a pressure switch or rollout switch, or adjust the gas valve. In BC, gas work is restricted to licensed gas fitters, and bypassing a safety switch removes the one thing protecting the household.
| Likely cause (most common first) | What you may notice | Owner-safe check | When it becomes a licensed call |
|---|---|---|---|
| 1. Weak flame signal from a dirty or poorly positioned flame sensor | Burners light, run a few seconds, then go out; the pattern repeats every heat call | Replace a dirty air filter and confirm the furnace has power; nothing more | Always. Cleaning, positioning and testing the sensor and its ground path is technician work behind the panels |
| 2. Blocked or restricted intake or exhaust pipe outside | Dropouts get worse on windy or snowy days, or after leaves come down | Look at the outdoor pipe ends and gently clear snow, leaves or debris you can reach by hand from the ground | If you see a nest, damage, a sagging pipe, or the code returns after clearing |
| 3. Condensate not draining properly | Water near the furnace, gurgling, or the fault appears after long run times | Look at the visible drain tubing and where it ends; note kinks, water on the floor or a drain that never drips | When the trap, internal hoses or a condensate pump need attention, or water has reached electrical parts |
| 4. Marginal gas supply or pressure | Other gas appliances also act up, or the flame looks small and lazy through the sight window | Confirm the manual gas valve at the furnace is open and that your other gas appliances work | Always. Measuring and adjusting gas pressure is licensed gas work |
| 5. Burner or orifice fouling | Uneven flame, slow light-off, more noise at ignition | Nothing beyond the filter; do not remove the burner cover | Always. Burner cleaning and inspection is done by a licensed gas fitter |
| 6. Flame rollout or pressure-switch interaction | Abrupt shutdowns, sometimes with a scorched smell or soot near the burner area | Do not keep resetting; turn the thermostat off and call | Immediately. It points to a combustion or venting problem that needs a licensed diagnosis |
How our York furnace error code 6 repair visit works
Diagnostic service calls are $189.00. That covers a licensed gas technician coming to your home, finding the real cause of the flame loss and explaining it to you before any repair goes ahead. Here is how the visit runs, step by step.
- Step 1, the booking: we ask what you have seen, how often the furnace drops out and whether anything changed recently, such as a renovation, a new filter or a heavy snowfall. We offer same-day where we can, depending on the day’s workload and where you are in the region, and we tell you honestly what the earliest slot is.
- Step 2, safety first on arrival: the technician checks for gas odour and carbon monoxide around the furnace and in the living areas before anything else.
- Step 3, read the history: we confirm the blink code on the board, check any stored fault history the control keeps, and compare it with the label for your unit.
- Step 4, watch it fail: we run a heat call and observe ignition, flame establishment and the moment the flame drops, so the diagnosis rests on what the furnace actually does rather than on a guess.
- Step 5, measure with the right meters: a microamp meter reads the flame signal the board is seeing; a manometer measures incoming and manifold gas pressure and the pressure-switch circuit; a combustion analyzer checks the flue gases; a multimeter confirms supply voltage, polarity and the ground the flame sensor relies on.
- Step 6, inspect venting and drainage: intake and exhaust runs, joints, slope and support, the outdoor terminations, the condensate trap and the drain path.
- Step 7, explain and quote: you get the cause, the fix and a written quote before any work beyond the diagnosis. Nothing is replaced without your go-ahead.
- Step 8, repair and test the safeties: after the repair we run full heat cycles, re-measure the flame signal and gas pressure, confirm the limit, rollout and pressure switches operate as designed, and leave the furnace heating.
What parts fix a York furnace flashing 6, and what should be in writing?
The parts most often involved in a flame-loss repair are, in general terms, the flame sensor, the burner assembly and its orifices, pressure-switch tubing or the switch itself, the condensate trap and hoses, and vent sections or terminations. Less often it is the gas valve or the control board. Many flame-loss calls end with cleaning, repositioning, or correcting a ground connection or a drain rather than a new part. A control board and a gas valve sit at the more expensive end of furnace parts, which is exactly why we prove a part has failed with a measurement before we quote it.
What decides the job on site is usually the venting and the drainage, not the sensor alone. A sensor that gets dirty again within weeks is often a symptom: poor combustion, a sagging vent that holds water, or a trap that backs up can all coat or disturb the flame. Fixing only the sensor in those homes brings the code back. A correct job finds the reason the flame was unstable and fixes that too.
What you should see in writing at the end of the visit:
- The code observed and the conditions when it appeared.
- The measurements that matter, such as flame signal, gas pressures and combustion readings, explained in plain language.
- What was cleaned, adjusted or replaced, and why.
- Any venting, drainage or gas-piping concerns found, even if you choose not to address them yet.
- Whether a Technical Safety BC permit was needed; vent and gas-line changes are done under permit.
- A written quote for any further work, so you can decide without pressure.
Repair or replace an older York furnace that keeps flashing code 6?
A flame-loss code on its own is not a reason to replace a furnace. Most 6-flash faults are fixed with sensor, burner, venting or drain work, and a well-kept furnace can keep going for years after that. The question changes when the code is one symptom among several on an older unit. These are the factors we talk through with owners:
- Age and history: an older furnace that has needed several repairs in recent seasons deserves a frank conversation.
- Heat exchanger condition: if inspection finds cracking or heavy corrosion, repair is no longer the safe answer.
- Parts availability: some older control boards and gas valves become hard to source, and we will tell you if that applies to yours.
- Venting that no longer suits the appliance: older vent runs sometimes need to be brought up to current code regardless.
- Comfort problems a repair will not touch: uneven rooms, noisy ducts or rising gas use.
- If replacement makes sense, the in-home estimate for a new furnace is free. If you go ahead with a replacement through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation. The quote is written, includes the permit in the scope, and you are never pushed to decide on the day.
- Replacement is also the moment to look at dual fuel: a heat pump that handles heating and cooling through most of our mild, wet winters, paired with a new gas furnace that takes over during cold snaps. For many Greater Vancouver homes that keeps the dependability of gas heat while adding air conditioning. We lay out a straight furnace replacement and a dual-fuel option side by side so you can compare.
York furnace error code 6 service in Vancouver, Burnaby, Surrey and across Greater Vancouver
We service York furnaces throughout Greater Vancouver from our base in Burnaby. Housing stock varies across the region and it shapes how a flame-loss call goes, so here is what we commonly run into. These are general patterns, not rules for any particular street or home.
Strata homes need one extra step: changes to vent terminations on exterior walls may need strata approval, and we can provide the written scope your council asks for. Brands we service for gas furnaces include York, Coleman, Luxaire, Lennox, Carrier, Bryant, Trane, American Standard, Goodman, Amana, Rheem, Ruud, Daikin and KeepRite. We are an independent TSBC-licensed contractor (licence LGA0090068, Class B gas CGA0028029) with our own licensed gas fitters, not a dealer or warranty centre for any brand, so every furnace gets the same measured diagnosis, a written quote before work, and permits and inspections where the job calls for them. To book, call (604) 473-9690 and tell us your York furnace is flashing 6, how often it drops out and whether the outside vent pipes looked clear.
- Vancouver: older character houses that were converted to high-efficiency furnaces at some point, alongside newer infill and laneway homes. Older conversions can have vent and drain routes added later that are worth a close look.
- Burnaby: many split-levels and post-war family homes with furnaces in basements or utility rooms, plus townhouse complexes where vent terminations sit close to walkways and neighbours.
- Surrey: large areas of subdivision housing with side-wall terminations, where landscaping, fences and shrubs can crowd the intake and exhaust over time.
- Richmond: low-lying, damp sites where outdoor terminations and condensate lines are worth checking after long stretches of rain.
- Coquitlam and the Tri-Cities (Coquitlam, Port Coquitlam and Port Moody): hillside homes and townhouses where higher ground can collect more snow and bury low terminations during a cold snap.
- The North Shore (North Vancouver and West Vancouver): higher elevations, more snow and more trees, so needles, leaves and snow at the vent ends come up often.
- New Westminster: older houses and converted multi-unit buildings where furnaces may sit in tight closets and venting has sometimes been reworked more than once.
- Delta and Langley: established neighbourhoods and newer developments, with some properties farther from the core; we give you realistic timing when you book.
More questions homeowners ask
What does 6 flashes mean on a York furnace?
Six flashes on a York furnace is commonly documented as flame loss: the burners lit, but the control lost the flame signal, often several times in one heating cycle. Confirm against the manual or the label inside the blower door for your unit. The furnace shuts the gas off each time, so the symptom you notice is heat that keeps cutting out.
Can I reset my York furnace when it is flashing code 6?
Once, and only if your owner manual describes a reset. Turn the thermostat down, switch the furnace off at its service switch for about a minute, then switch it back on. If the 6 flashes return, stop resetting and call a licensed technician, because repeated resets can hide a venting or combustion fault.
Is it safe to run a York furnace with error code 6?
The furnace protects itself by shutting off the gas whenever the flame drops, so the code is a safety response rather than a hazard on its own. Forcing it to keep running is not wise, because some causes involve venting, rollout or combustion air. If you smell gas or a CO alarm sounds, leave the home and call FortisBC or 911 from outside.
Can a dirty flame sensor cause York furnace error code 6?
Yes, a weak flame signal from a dirty or poorly positioned flame sensor is one of the most common causes we find. Cleaning and testing the sensor means working inside the burner compartment, so it is a job for a licensed technician. We measure the flame signal before and after, and look for the reason the sensor got dirty so the code does not come back.
Who fixes York furnace error code 6 near me in Greater Vancouver?
BC Wide’s licensed gas fitters repair York furnaces in Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We book same-day where we can and give you an honest earliest time when you call (604) 473-9690. You get a written quote before any work beyond the diagnosis.
Should I replace my York furnace if it keeps flashing 6?
Usually not for this code alone, since most flame-loss faults are repaired by addressing the sensor, burners, venting or drainage. Replacement makes sense when an older furnace also has a damaged heat exchanger, hard-to-source parts or a run of recent repairs. If you replace through BC Wide, the in-home estimate is free and the $189.00 diagnostic charge is waived and taken off the installation.
- Weil-McLain Boiler Code E52 — Flue temperature too high | BC Wide
- Weil-McLain Boiler Code E60 — Parameter reading error | BC Wide
- Weil-McLain Boiler Code E61 — Airflow circuit failure | BC Wide
- Weil-McLain Boiler Code E65 — Insufficient blower force / blower restart fault | BC Wide
- Weil-McLain Boiler Error Codes & Repair | Greater Vancouver | BC Wide
- Weil-McLain Boiler Error Codes & Troubleshooting in Greater Vancouver
- Rheem furnace error codes
- Whirlpool Furnace Error Codes
- Why does my Navien have no error code but no hot water?
- Keeprite furnace error code 6
Frequently asked questions
How often should a furnace be serviced?
How long does a furnace last in Vancouver's climate?
Why is my furnace blowing cold air?
How much does a new furnace cost in Vancouver?
What is the most reliable furnace brand?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


