York furnace error code 8 flashes means the control has detected a problem with the hot-surface igniter or its circuit, such as an open igniter or low igniter current (confirm against the manual for your unit). The burners cannot light, so the furnace locks out and the house loses heat. Check power, the furnace switch, the gas supply valve and the thermostat, reset once only if your manual allows it, then call a licensed gas technician. BC Wide serves Greater Vancouver at (604) 473-9690.
If your York furnace is showing 8 flashes (Igniter / ignition circuit fault), here’s exactly what it means and what to do. This guide is part of our full York furnace error code list.
Severity: Critical — likely no heat / lockout.
What 8 flashes means on a York furnace
The control has detected a problem with the hot-surface igniter or its circuit (for example, an open igniter or low igniter current).
Common causes
- Cracked or worn-out hot-surface igniter
- Open igniter wiring or connector
- Control board igniter-output fault
What you can safely check first
- No safe homeowner check for the igniter
- Confirm the furnace has power and the thermostat is calling for heat, then call a professional
Only attempt the basics above. Do not open the gas train, burner compartment or control wiring.
When to call a technician
This is a fault that should be diagnosed by a licensed technician. Repeated lockouts on a York furnace usually point to a real fault that will keep recurring until it’s fixed properly — and continually resetting power can hide a safety issue.
BC Wide Heating & Air Conditioning has serviced Greater Vancouver furnaces since 1999. Diagnostics and repairs are carried out by our own Technical Safety BC–licensed technicians (gas contractor licence LGA0090068, Class B Gas Licence CGA0028029) — never subcontractors — and we’re rated 4.7★ across 180+ Google reviews. Honest pricing and free written quotes on replacements.
York furnace repair across Greater Vancouver
If a York furnace showing 8 flashes won’t reset or has locked out, don’t keep cycling the power — you can mask a real fault or a safety condition. BC Wide provides fast furnace repair and emergency HVAC service 7 days a week throughout the Lower Mainland. Call 604-473-9690 or email info@bcwide.ca and a licensed technician will diagnose the real cause and get your heat & comfort back. See our emergency HVAC service.
Related York furnace codes
- York furnace Steady ON — Normal operation
- York furnace LED OFF — No power to control / control failure
- York furnace Rapid continuous flash — Line-voltage polarity reversed / grounding issue
- York furnace 2 flashes — External lockout (retries exhausted)
- York furnace 3 flashes — Pressure switch / draft fault
- York furnace 4 flashes — High-limit / temperature limit open
Frequently asked questions
Is 8 flashes on a York furnace serious?
It’s a lockout/safety code — the furnace has shut down and needs prompt diagnosis. BC Wide repairs York furnaces 7 days a week across Greater Vancouver.
How do I reset a York furnace after 8 flashes?
You can try one power cycle at the breaker/switch after checking the filter and thermostat. If the code returns, stop resetting it and book a licensed technician — a recurring code is a real fault, not a glitch.
York Furnace Error Code 8 Flashes: What It Means for Your Home
In plain terms, 8 flashes is the furnace telling you it tried to start and could not get the igniter ready to light the gas. As described above, the control has detected a problem with the hot-surface igniter or its circuit, for example an open igniter or low igniter current. Confirm that meaning against the manual or the wiring diagram label inside the door of your unit, because control boards are revised over the years and the label on your own furnace is the authority.
For you, that means three things. First, heat: without a glowing igniter the gas valve should never open, so the burners stay dark and the blower may run briefly or not at all. The house cools down hour by hour, and in a cold snap that matters for pipes, pets and anyone elderly or unwell at home. Second, hot water: in most Metro Vancouver homes with a York furnace, domestic hot water comes from a separate water heater, so showers usually still work. If your home has a combination setup where the air handler is fed by a water heater or boiler, tell us how the system is arranged when you call, because the troubleshooting path is different. Third, safety: an igniter fault is the furnace failing safe. The control is doing its job by refusing to send gas to burners that cannot be lit. That is good news, but it also means nobody should try to defeat that logic.
Owners usually describe the problem in their own words long before they find the code chart. These are the things people tell us on the phone:
- The furnace clicks on, a fan inside hums for a bit, then everything goes quiet and no warm air comes out.
- I can see a light blinking through the little window on the furnace door, and it keeps repeating the same pattern.
- It worked after I flipped the switch off and on, but it quit again the same night.
- The thermostat says heating, but the vents are blowing cool air or nothing at all.
- There used to be an orange glow through the sight glass before the flame came on, and now there is no glow.
- The furnace started acting up right after a power flicker, a storm, or after someone did work near it.
York Furnace Error Code 8 Flashes: What We Check First, Most Likely Cause First
The order below reflects what we most often find behind an igniter-circuit fault on gas furnaces in general. Your furnace may differ, and only meter readings taken on site settle it. Each row shows what the owner may notice, the only check an owner should make, and the point where it becomes a licensed call.
Owner-safe checks, in this order, are the only steps we recommend before calling:
- Power: the furnace service switch, often a light-switch style toggle on or near the furnace, is on, and the furnace breaker in the panel is on. Reset a tripped breaker once only.
- Gas supply: the manual shut-off valve on the gas line to the furnace is open, with the handle running in line with the pipe. Do not touch any valve or control inside the furnace cabinet.
- Thermostat: it is set to heat, the set point is above room temperature, and the batteries are fresh if it uses them.
- Furnace door: the blower door is fully seated. Most furnaces have a door switch that cuts power when the panel is loose.
- Outside terminals: on a high-efficiency York with plastic venting, the intake and exhaust pipes where they leave the house are clear of snow, leaves, nests or debris.
- Condensate drain: the visible drain tube and trap, if you can see them without removing panels, are not kinked, cracked or overflowing.
- Reset: only if your owner manual describes a reset, and only once. If 8 flashes returns, leave the furnace off and call a licensed technician.
| Likely cause (most common first) | What the owner may notice | Owner-safe check | When it becomes a licensed call |
|---|---|---|---|
| 1. Cracked or worn-out hot-surface igniter | No orange glow at start-up; the code returns after every reset | Confirm power and a heat call only. Do not remove the burner cover or touch the igniter; it is brittle and skin oils shorten its life | Always. Testing and replacing the igniter happens inside the burner compartment next to the gas valve |
| 2. Loose, burnt or corroded igniter connector or wiring | Fault comes and goes, sometimes after the furnace has been bumped or after damp weather | None beyond confirming power. Do not open the control compartment or wiggle wires | Always. Wiring checks are done with power isolated and a meter by a qualified technician |
| 3. Control board igniter-output fault | Igniter is new or tests fine, yet the code still appears | Note when it happens and whether a power surge or outage came first | Always. Board diagnosis requires live voltage and current readings |
| 4. Low or unstable supply voltage reaching the furnace | Fault more common after storms, breaker trips or electrical work in the house | Check the furnace service switch is on and the breaker has not tripped; reset a tripped breaker once only | If the breaker trips again, or the switch looks scorched or feels warm, stop and call |
| 5. Wrong or mismatched igniter fitted during an earlier repair | Code returns weeks or months after a previous igniter replacement | Find the old invoice so the technician can see what was installed | Always. The replacement must match the part specified for your furnace |
What Not to Do, and the Gas and Carbon Monoxide Safety Line
Please do not remove the burner compartment cover, unplug or touch the igniter, jumper or bypass any switch, borrow parts from another appliance, or keep cycling the power hoping the furnace eventually catches. Repeated restarts on a failing ignition circuit stress the control board and can hide a second problem that a technician needs to see. Igniter, wiring and control board work sits inside a gas appliance, and in British Columbia that work belongs to a qualified gas technician working for a licensed contractor.
Gas and carbon monoxide safety: if you smell gas, a rotten-egg or sulphur odour, or your carbon monoxide alarm sounds, do not operate light switches, the thermostat or the furnace. Get everyone out of the house, then call FortisBC or 911 from outside. An igniter code on its own is not a gas leak, but treat any odour or alarm as the emergency first and the furnace second. Every home with gas appliances should have working CO alarms near sleeping areas, tested regularly and replaced when the alarm reaches the end of its service life printed on the unit.
How Our York Furnace Code 8 Repair Visit Works
Diagnostic service calls are $189.00. We book same-day where we can. In a cold snap the schedule fills quickly, and we will tell you honestly what the earliest realistic arrival is rather than promise a window we cannot keep. Here is what happens from the moment you call:
- Step 1, the call: we ask what the furnace is doing, how long it has been happening, what you have already checked and roughly how old the furnace is. If you can read the model and serial numbers off the rating plate, have them ready.
- Step 2, safety first on arrival: the technician checks the area for gas odour, asks about CO alarms, and reads the fault indication on the control board before touching anything.
- Step 3, watch a start-up: we run the furnace through a heat call and observe the sequence of inducer, pressure switch, igniter warm-up and gas valve. Seeing exactly where the sequence stops narrows the fault quickly.
- Step 4, measure: with the right meters we check supply voltage at the furnace, igniter resistance with power isolated, and the voltage and current the board delivers to the igniter during warm-up. Those readings tell us whether the igniter, the wiring or the board is at fault, so we are not guessing with parts.
- Step 5, explain and quote in writing: you get the finding in plain words and a written quote before any work beyond diagnosis. The parts most often involved are the hot-surface igniter itself, the igniter harness or connector and, less often, the integrated control board.
- Step 6, repair with the correct part: we fit a replacement specified for your furnace, handle a new igniter without bare-hand contact, and secure the wiring away from hot surfaces and sharp edges.
- Step 7, test the safeties: after the repair we run several full heating cycles and confirm ignition, flame sensing, the pressure switch, the high-limit and the rollout switches behave as designed, leak-check any gas joint we disturbed, and check the combustion venting.
- Step 8, paperwork: you receive a written record of what was found, what was replaced and the readings taken, which helps with any manufacturer warranty claim and when you sell the house.
Should I Repair or Replace an Older York Furnace With an Igniter Fault?
On its own, a code 8 fault is usually a repair, not a reason to replace the furnace. A hot-surface igniter is a wear part; it is expected to fail at some point in a furnace’s life, and replacing it is routine work. A control board is one of the more expensive parts on a gas furnace, so a board failure on an old unit is where the conversation changes.
We look at the whole furnace before giving an opinion: the age on the rating plate, the condition of the heat exchanger, whether the inducer and blower motors are noisy or tired, how many repairs the unit has had recently, whether parts are still readily available, and whether the furnace was sized correctly for the house in the first place. A furnace with a sound heat exchanger and one worn igniter is a good repair. A furnace near the end of its expected life with a failed board, rust in the burner area and a history of call-backs often is not.
If replacement is on the table, the in-home estimate for a new furnace is free, and if you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived and taken off the installation. Many Metro Vancouver owners also ask about dual fuel at this point: a heat pump paired with a gas furnace, where the heat pump carries most of our mild, wet coastal winter and the gas furnace takes over as backup in cold snaps. We will tell you whether your ductwork, electrical panel and gas line suit it, and give you a written quote for each option so you can compare them on paper.
- Repair usually makes sense when the fault is the igniter or its connector, the furnace is mid-life, and the heat exchanger and motors check out.
- A replacement estimate is worth getting when the control board has failed on an older furnace, parts are hard to source, or there have been several unrelated repairs in recent winters.
- Replacement should not wait when a cracked heat exchanger or another combustion safety problem is found during the visit. We will not restart a furnace we believe is unsafe.
York Furnace Error Code 8 Flashes Repair Near Me in Greater Vancouver
BC Wide is based in Burnaby and has worked on furnaces across Metro Vancouver since 1999. We cover Vancouver, Burnaby, Surrey, Richmond, Coquitlam and the rest of the Tri-Cities, the North Shore, New Westminster, Delta and Langley. Same-day where we can; bridge traffic and the time of year both affect how soon we can arrive. Housing stock varies a lot across the region, and it shapes the visit:
Our mild, wet coastal climate is gentle on equipment in one sense, but it means furnaces cycle on and off many times a day through a long heating season. Every start-up is a heat cycle for the hot-surface igniter, so igniters here tend to wear through cycles rather than through extreme cold. Damp basements, crawlspaces and garages can also corrode connectors over time, which is one reason an intermittent igniter fault is common in older homes around the region.
Gas furnace brands we service include York, Luxaire, Coleman, Lennox, Carrier, Bryant, Trane, American Standard, Goodman, Amana, Rheem, Ruud, Daikin, Keeprite and Napoleon. We service these brands as an independent contractor; we are not a factory-authorised dealer or warranty centre for any of them, York included.
- Vancouver and Burnaby: a wide mix of older detached houses, character homes and townhouses. Furnaces in older basements are often tucked into tight utility rooms, which affects access to the burner compartment.
- New Westminster: many older houses and conversions where the furnace may have been replaced more than once and the wiring around it altered over the years, so we check the electrical supply carefully.
- Surrey, Delta and Langley: many larger detached homes and newer townhouse developments with high-efficiency furnaces, whose plastic intake and exhaust terminals often sit low on side walls where leaves and debris collect.
- Richmond: plenty of townhouses and strata complexes, where furnaces are often in closets or attic spaces and access, parking and strata rules shape the visit.
- Coquitlam, Port Coquitlam and Port Moody: a blend of established neighbourhoods and newer hillside development; homes higher up the slopes can see more snow at vent terminals.
- North Vancouver and West Vancouver: more frequent snow at elevation and heavy winter rain, so we check terminals and condensate drains as part of every no-heat visit.
More questions homeowners ask
What does 8 flashes mean on a York furnace?
It means the control has detected a problem with the hot-surface igniter or its circuit, such as an open igniter or low igniter current. The furnace cannot light the burners and will usually lock out, leaving you without heat. Confirm the meaning against the manual or door label for your unit, then call a licensed gas technician for diagnosis.
Can I reset a York furnace showing 8 flashes?
Only if your owner manual describes a reset, and only once. Turn the furnace switch off, wait as the manual directs, then turn it back on with the thermostat calling for heat. If 8 flashes returns, leave the furnace off; repeated resets will not fix a cracked igniter or a failed circuit and can hide other faults.
Is it safe to run my York furnace with code 8?
The furnace will not heat normally with this code, because the control blocks the gas when the igniter cannot do its job. That lockout is a safety feature, so never try to bypass it. If you smell gas or a CO alarm sounds, leave the home and call FortisBC or 911 from outside.
Can I replace a York furnace igniter myself?
We advise against it. The igniter sits in the burner compartment next to the gas valve, the part is fragile, and a mismatched replacement or poorly routed wire causes repeat failures. In BC, work inside gas appliances belongs with a licensed gas technician, and a proper repair includes testing the safeties afterwards.
How much does it cost to fix York furnace error code 8?
Diagnostic service calls are $189.00, and you receive a written quote before any work beyond diagnosis. The repair cost depends on whether the fault is the igniter, the wiring or the control board, and a control board is one of the more expensive parts on a gas furnace. If you choose to replace the furnace through BC Wide instead, the $189.00 diagnostic charge is waived.
Who repairs York furnaces near me in Greater Vancouver?
BC Wide services York gas furnaces across Vancouver, Burnaby, Surrey, Richmond, Coquitlam, the Tri-Cities, the North Shore, New Westminster, Delta and Langley. We are an independent TSBC-licensed contractor (gas contractor licence LGA0090068, Class B gas licence CGA0028029), not a York dealer, and we book same-day where we can. Call (604) 473-9690 and tell us the furnace is showing 8 flashes.
- Weil-McLain Boiler Code E52 — Flue temperature too high | BC Wide
- Weil-McLain Boiler Code E60 — Parameter reading error | BC Wide
- Weil-McLain Boiler Code E61 — Airflow circuit failure | BC Wide
- Weil-McLain Boiler Code E65 — Insufficient blower force / blower restart fault | BC Wide
- Weil-McLain Boiler Error Codes & Repair | Greater Vancouver | BC Wide
- Weil-McLain Boiler Error Codes & Troubleshooting in Greater Vancouver
- Rheem furnace error codes
- Whirlpool Furnace Error Codes
- Why does my Navien have no error code but no hot water?
- Keeprite furnace error code 6
Frequently asked questions
How often should a furnace be serviced?
How long does a furnace last in Vancouver's climate?
Why is my furnace blowing cold air?
How much does a new furnace cost in Vancouver?
What is the most reliable furnace brand?
What HVAC services does BC Wide offer in Metro Vancouver?
How long has BC Wide been in business?
What areas do you serve?
What Greater Vancouver homeowners say about BC Wide
Get a Free Quote — Right From This Page
Request a Free Quote
Get Comfortable — Talk to BC Wide Today
Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.


