★ 4.7 Google rating · Serving Greater Vancouver since 1999
ServicesBrandsRebates ReviewsAboutContact 📞 Call (604) 473-9690

Super Hot vs IBC Boilers: Which Is Right for Your Vancouver Home?

Boilers

Super Hot vs IBC Boilers: Which Is Right for Your Vancouver Home?
Home › Super Hot vs IBC Boilers: Which Is Right for Your Vancouver Home?

Super Hot vs IBC Boilers: Which Is Right for Your Vancouver Home?

Quick answer

For most Greater Vancouver homes, the choice between Super Hot and IBC comes down to the house, not the badge. Super Hot suits owners who want a simple, rugged, easy-to-service boiler. IBC suits homes that benefit from modern condensing operation and finer modulation across changing heat loads. The deciding factors are your heat-loss calculation, emitter type, venting route, domestic hot-water needs and the condition of the existing piping. BC Wide services and installs both brands and gives a free in-home estimate for any replacement. Call (604) 473-9690.

Key takeaways

  • Both Super Hot and IBC boilers are engineered and built in Vancouver, BC, which means local parts supply and designs proven in our wet coastal climate.
  • Super Hot (by Allied Engineering) is known for simple, rugged, service-friendly boilers with a long track record in BC homes.
  • IBC Technologies focuses on modern condensing boiler technology with advanced controls and strong turndown for variable heating loads.
  • Neither brand is universally ‘better’ — the right choice depends on your home’s heat distribution, venting, hot-water needs, and how you weigh simplicity against technology.
  • Efficiency, sizing, and cost claims should always be verified against your specific home; ask for a written estimate rather than trusting generic numbers.
  • BC Wide services and installs both brands across the Lower Mainland as an independent TSBC-licensed gas contractor.

If you are choosing between a Super Hot boiler (made by Allied Engineering) and an IBC boiler (made by IBC Technologies), the honest answer is that both are excellent — and both are manufactured right here in Vancouver, BC. The better fit depends on your home: Super Hot’s strength is rugged simplicity and easy servicing, while IBC’s strength is modern condensing technology and sophisticated controls.

That local angle matters more than most homeowners realize. A boiler designed and built in the Lower Mainland is engineered by people who understand our long, damp heating season, our mild-but-relentless winters, and the hydronic systems common in Vancouver-area housing stock. Parts and factory support are also close by, which shortens downtime when something eventually needs attention.

BC Wide has installed and serviced both brands across Greater Vancouver since 1999. We are an independent, Technical Safety BC licensed gas contractor — not a factory-authorized dealer for either manufacturer — so we have no incentive to push one over the other. This guide lays out the real trade-offs so you can make the call with clear eyes.

Who makes Super Hot and IBC boilers?

Super Hot boilers are made by Allied Engineering, a Vancouver, BC manufacturer that has been building hydronic heating equipment for decades. IBC boilers are made by IBC Technologies, also headquartered and manufacturing in Vancouver. Choosing either brand means choosing a boiler designed, tested, and supported in the same climate it will heat.

This is genuinely unusual. Most boilers sold in Canada are designed in Europe, the United States, or Asia and adapted for our market. Allied Engineering and IBC Technologies both build for BC conditions first: long shoulder seasons, high humidity, and homes that run hydronic heat for eight or nine months of the year. Local manufacturing also means replacement parts typically don’t have to cross an ocean or a border to reach your mechanical room.

What is Super Hot’s design philosophy?

Super Hot boilers are built around rugged simplicity. Allied Engineering’s reputation in the trade rests on straightforward, durable boilers that are easy for technicians to diagnose and service, with fewer complex electronic components that can fail. Many BC homes have run Super Hot boilers reliably for decades with basic annual maintenance.

For homeowners, that philosophy translates into predictability. A simpler boiler has fewer sensors, boards, and proprietary parts that can strand you waiting for a specialty component. Technicians across the Lower Mainland know these units well because they have been in local basements and mechanical rooms for so long. If your priority is a heating appliance that just works, year after year, with uncomplicated servicing, Super Hot’s approach is compelling.

The trade-off is that simpler designs generally lean on more traditional combustion and control technology. If you want the deepest possible modulation, outdoor-reset sophistication, or condensing operation squeezing extra heat from flue gases, you are describing the other side of this comparison.

What is IBC’s design philosophy?

IBC Technologies builds modern condensing boilers with advanced electronic controls. Condensing boilers extract additional heat from exhaust gases that older designs vent outdoors, and IBC pairs that with strong modulation — the ability to turn the burner down to match small heating loads instead of cycling on and off — plus detailed control interfaces for dialing in comfort.

That capability suits how Lower Mainland homes actually heat. Our winters are mild and wet rather than bitterly cold, so a boiler spends most of its life running at partial load. A condensing boiler with wide turndown can idle along efficiently through a grey Vancouver January instead of short-cycling. IBC’s controls also handle multiple heating zones, indirect hot-water tanks, and outdoor-reset logic elegantly.

The trade-off is complexity. Condensing boilers have more components — condensate drains, combustion sensors, control boards — and they reward owners who keep up with annual professional maintenance. They are not fragile, but they are not fit-and-forget appliances either.

How do the two brands compare side by side?

Neither brand wins every category. The comparison below reflects what we see in the field servicing both across Greater Vancouver — treat it as a starting point, not a verdict, because the right answer always depends on your specific home and system.

FactorSuper Hot (Allied Engineering)IBC Technologies
Design philosophyRugged, simple, service-friendlyModern condensing, control-rich
Best fitHomeowners who prioritize durability and simple servicingHomeowners who want top efficiency and fine-grained comfort control
ServicingWidely understood by local technicians; straightforward diagnosticsNeeds technicians comfortable with condensing systems and electronic controls
Maintenance demandsBasic annual serviceAnnual service including condensate and combustion checks
Parts availabilityLocal — manufactured in VancouverLocal — manufactured in Vancouver
ComplexityLower — fewer electronic componentsHigher — more sensors and boards, more capability

Which boiler suits which Greater Vancouver home?

Choose based on your home’s heating system and your own priorities. A Super Hot boiler tends to suit older homes with traditional radiator or baseboard hydronic systems, owners who value simplicity, and situations where straightforward, proven equipment matters more than squeezing out every unit of efficiency. An IBC boiler tends to suit renovated or newer homes, in-floor radiant systems, multi-zone setups, and owners who want condensing efficiency with modern controls.

Venting and mechanical-room realities matter too. Condensing boilers need a condensate drain and appropriate venting, which is easy in some homes and awkward in others. Existing chimney configurations, gas line sizing, and available wall space for venting can all tilt the decision one way or the other. This is exactly what a proper in-home assessment sorts out before anyone recommends a brand.

  • Older character home with cast-iron radiators and a simple single zone: Super Hot is often the natural fit.
  • Renovated home with in-floor radiant heat and multiple zones: IBC’s modulation and controls shine.
  • Home that also needs domestic hot water from the boiler: both brands can work with indirect tanks — system design decides it.
  • Tight mechanical closet with tricky venting: the venting solution may pick the boiler for you.
  • Owner who wants minimal technology to think about: lean Super Hot. Owner who enjoys optimizing settings: lean IBC.

Why does the local-manufacturer angle actually matter?

Because when a part fails in February, distance is downtime. With both Allied Engineering and IBC Technologies based in Vancouver, parts distribution is regional, factory technical support runs in your own time zone, and the engineering behind the product was validated in the exact climate stressing it. That is a practical advantage, not just a feel-good story.

It also shows up in longevity of support. Brands with a deep local install base keep parts flowing for older models far longer, because thousands of Lower Mainland homes depend on them. Both of these manufacturers have decades of local installations behind them, which is reassuring whichever way you go.

What determines the installed cost of either boiler?

Rather than quoting numbers that would be wrong for your home, understand the factors that drive any boiler installation quote: the equipment itself and its capacity, the complexity of removing the old boiler, venting changes (especially converting to condensing venting), condensate drainage, gas line sizing, required permits, labour hours, and any code upgrades your existing system needs to pass a Technical Safety BC inspection.

Two identical boilers can carry very different installed costs in two different homes because of those variables. The only honest way to compare Super Hot versus IBC on price for your house is a written estimate based on an in-home assessment. Be wary of anyone who quotes a firm figure over the phone without seeing your mechanical room.

Financing is available, and it is worth asking about current CleanBC, FortisBC, and BC Hydro programs when you plan the project — programs change often, so we confirm what applies at the time of your estimate rather than promising eligibility.

Can one company service both brands?

Yes. BC Wide installs, services, and repairs both Super Hot and IBC boilers throughout Greater Vancouver as an independent contractor licensed by Technical Safety BC, with Red Seal technicians on staff. We are not a factory-authorized dealer for either manufacturer, and we consider that a feature: our recommendation is based on your home, not on a dealer agreement.

Whichever brand you own or choose, annual maintenance is what protects it. A yearly service visit checks combustion, safety controls, water pressure, and — on condensing models — the condensate system, catching small issues before they become winter breakdowns. Both manufacturers build durable equipment; regular maintenance is what lets that durability show.

Gas & carbon-monoxide safety: Gas and carbon monoxide safety: both Super Hot and IBC boilers are gas-fired combustion appliances. If you ever smell gas or suspect carbon monoxide — headaches, dizziness, a CO alarm sounding — leave the home immediately and call your gas utility’s 24-hour emergency line or 911 from outside. Install CO alarms on every level of your home and test them regularly. Gas boiler installation, conversion, and repair are legally restricted to licensed gas technicians in BC; never open the combustion side of a boiler yourself.

Frequently asked questions

Are Super Hot and IBC boilers really both made in Vancouver, BC?

Yes. Super Hot boilers are manufactured by Allied Engineering and IBC boilers by IBC Technologies, and both companies are based in Vancouver, British Columbia. For Lower Mainland homeowners this means regional parts distribution, local factory support, and equipment engineered for the same wet, mild coastal climate it will operate in — a practical advantage few other boiler brands can match.

Which brand is more reliable, Super Hot or IBC?

Both have strong reliability records in BC homes when properly installed and maintained. Super Hot’s simpler designs have fewer electronic components that can fail, while IBC’s condensing boilers are robust but depend more on consistent annual maintenance. In our field experience across Greater Vancouver, installation quality and yearly servicing influence long-term reliability more than the badge on the cabinet.

Is a condensing IBC boiler worth it in Vancouver’s mild climate?

Often, yes — mild climates are actually where modulating condensing boilers do well, because they run long, low-fire cycles through our extended shoulder seasons instead of short-cycling. Whether the added complexity is worth it for your home depends on your heat distribution, venting options, and how long you plan to stay. An in-home assessment gives you a grounded answer.

Can I replace my old Super Hot boiler with an IBC, or vice versa?

Usually, yes. Switching brands during a replacement is common, but it can involve venting changes (particularly moving to condensing venting), condensate drainage, gas line verification, and control rewiring. Sometimes staying with the same style of boiler simplifies the project considerably. We assess your existing system in Greater Vancouver and lay out both paths in a written estimate so you can compare.

Do I need a factory-authorized dealer to install or service these boilers?

No. In BC, gas boiler work must be performed by a Technical Safety BC licensed gas contractor, but that contractor does not need to be factory-authorized. BC Wide is an independent licensed contractor — not a factory-authorized dealer for either brand — and services both Super Hot and IBC boilers across the Lower Mainland. Independence means our brand recommendation follows your home’s needs.

How often should a Super Hot or IBC boiler be serviced?

Annually, ideally before the heating season ramps up in fall. A yearly service covers combustion checks, safety controls, water pressure, and system cleaning; condensing IBC models also need their condensate trap and drain inspected. Regular maintenance protects efficiency, catches wear early, and supports manufacturer warranty expectations. Given how long Lower Mainland heating seasons run, skipping service years tends to catch up with owners.

What information should I gather before requesting a boiler quote?

Note your current boiler’s brand and approximate age, how your home is heated (radiators, baseboards, in-floor radiant), how many heating zones you have, whether the boiler also supplies domestic hot water, and any comfort complaints like cold rooms or noise. Photos of the mechanical room, venting, and gas meter help too. With that context, a written estimate for your Greater Vancouver home becomes far more accurate.

BC Wide Home Services — Lower Mainland home-comfort specialists since 1999

Technical Safety BC Licensed Gas Contractor (LGA0090068) · Class B Gas Licence (CGA0028029) · Red Seal technicians · Evening and weekend calls · Diagnostic service calls $189.00 · Free in-home estimates on replacements (the $189.00 is waived if you replace with us). Call 604-473-9690 or book a free replacement estimate.

Super Hot vs IBC boiler comparison in Greater Vancouver: what we check first

Before we recommend either brand, we spend the first part of the visit on the house itself. A boiler is only as good as the system it is connected to, and in Greater Vancouver the existing system is often decades older than the boiler being replaced. The brand question is usually settled by what we find in the mechanical room, not by a spec sheet.

The table below is the checklist our licensed gas fitters work through on site. Each item points toward one design or the other, and together they decide which boiler will actually run well in your home.

What we check on siteWhy it mattersWhich way it tends to lean
Room-by-room heat-loss calculationSizing from the old boiler’s nameplate usually oversizes the new one and causes short cyclingNeutral: both brands need correct sizing; a low, variable load favours strong modulation
Emitter type: baseboard, cast-iron radiators, in-floor radiantReturn-water temperature decides whether a condensing boiler can actually condenseLow-temperature in-floor radiant favours condensing designs; high-temperature radiators narrow the gap
Venting route and chimney conditionCondensing boilers vent through plastic pipe to a sidewall or roof; older chimneys may need a liner or abandonmentA clear sidewall route makes a condensing install simpler; a tight lot or strata rules can complicate it
Condition of existing piping and waterSludge and corrosion in older hydronic loops can foul a new heat exchangerBoth brands need a clean system; dirty loops call for flushing, a dirt separator and water treatment
Domestic hot-water planAn indirect tank, a combi unit or a separate gas water heater each change the boiler choiceDiscuss with the installer; both brands offer configurations that work with indirect tanks
Gas supply and meter capacityA new appliance must be supplied at the pressure and volume the manufacturer requiresNeutral: confirmed by the gas fitter for any brand
Service access and who will maintain itA boiler squeezed into a closet is harder and slower to serviceOwners who value simple field servicing often lean toward Super Hot

What problems make Vancouver homeowners start comparing Super Hot and IBC?

Most people do not research boiler brands for fun. They start comparing because the boiler they have is giving them trouble. These are the problems we hear most, in the words owners use on the phone:

  • Some rooms are warm and others never get there, even with the thermostat turned up
  • The boiler keeps clicking on and off every few minutes
  • There is banging, gurgling or kettling noise in the pipes or the boiler
  • The pressure gauge keeps dropping and I have to top it up
  • There is water under the boiler or around the relief valve
  • The display shows a code or a light is flashing and the heat has stopped
  • Our gas bills went up but the house is not any warmer
  • The boiler is old and the technician said parts are getting hard to find
What you noticeCommon causes we findRepair or replace?
Short cyclingOversized boiler, failing control, poor flow or a sensor issueOften repairable; if it is oversizing, replacement fixes the root cause
Pressure keeps droppingSmall leak, failing expansion tank or relief valve weepingUsually a repair
Kettling or bangingSludge or debris restricting flow through the heat exchangerFlushing first; a badly fouled older exchanger may justify replacement
No heat with a code or flashing lightIgnition, flame sensing, venting or water-pressure faultDiagnose first, then decide; verify the code against the manual

How does a BC Wide boiler visit work, step by step?

Whether you are fixing a boiler or replacing one, the visit follows the same order so nothing is skipped and you always know what you are paying for before work starts.

  • Step 1, the call: you phone (604) 473-9690 and tell us what the boiler is doing. We book a time and, for no-heat calls in winter, go same-day where we can.
  • Step 2, the diagnosis: for a repair or no-heat call, a licensed technician tests the boiler, controls, venting and water side. Diagnostic service calls are $189.00.
  • Step 3, the honest recommendation: we tell you whether a repair makes sense or whether the boiler is at the point where replacement is the better use of your money, and why.
  • Step 4, the replacement estimate: if you are considering a new Super Hot or IBC boiler, the in-home estimate for replacement or installation is free. We measure, check venting and piping, and do the heat-loss work.
  • Step 5, the written quote: you receive a written quote covering scope, the boiler chosen, venting, piping changes, permit and warranty terms as written by the manufacturer and by us.
  • Step 6, the credit: if you go ahead with a replacement or new installation through BC Wide, the $189.00 diagnostic charge is waived, taken off the installation.
  • Step 7, the install and permit: a licensed gas fitter installs the boiler under a gas permit, and the work is open for inspection.
  • Step 8, commissioning and handover: we set the controls, test combustion and safety devices, and walk you through the system before we leave.

Super Hot or IBC in Vancouver neighbourhoods: how the housing stock changes the answer

Vancouver’s housing varies a lot from one side of the city to the other, and that variation is exactly why we will not recommend a brand over the phone. The notes below are general patterns we see; every house is assessed on its own.

In Kitsilano, Dunbar and Kerrisdale, many homes are older character houses, and some still run hot-water heat through cast-iron radiators. High-temperature radiators can limit how often a condensing boiler actually condenses, so the honest comparison there weighs simplicity against controls rather than assuming condensing always wins. Basement suites are also common, which can mean zoning the boiler so each suite has its own thermostat.

In Mount Pleasant, Grandview-Woodland and Hastings-Sunrise, we often find older homes that have been renovated in stages. That can mean mixed emitters, with original radiators upstairs and newer in-floor radiant in a basement or addition. Mixed temperatures call for careful piping and mixing controls, and an IBC-style modulating boiler with outdoor reset can be a good fit where the layout supports it.

In Marpole, Riley Park, Sunset, Oakridge, Killarney and Renfrew-Collingwood, the housing mix includes many mid-century houses and newer rebuilds. Rebuilds with in-floor radiant usually suit condensing operation well. Older houses may still have chimney-vented equipment, so the venting route for a new boiler, and what happens to the old chimney, is a key part of the quote.

Across all of these areas, soft Metro Vancouver water means the problems we see on the water side are sludge and corrosion rather than limescale. Whichever brand you choose, a flushed loop, a dirt separator and proper water treatment protect the new heat exchanger.

What should a correct Super Hot or IBC installation look like at handover?

A new boiler can look tidy and still be set up wrong. At handover you should be able to see, and have explained to you, each of the following. If any item is missing, ask before the installer leaves.

Gas and carbon-monoxide safety comes first with any gas boiler. Make sure there is a working carbon monoxide alarm near sleeping areas and near the mechanical room, keep vent terminals clear of snow, leaves and storage, and never block combustion air openings. If you smell gas, leave the house, do not touch switches, and call FortisBC from outside, then call a licensed gas fitter. Gas piping, venting and burner work are legally restricted to licensed gas fitters in BC; a homeowner may check the pressure gauge, keep the area clear and change the thermostat, but should not open the boiler or adjust gas components.

  • A gas permit pulled for the job, with the installation open for inspection
  • Venting run in the material and route the manufacturer specifies, with terminals clear of windows, doors and air intakes
  • A condensate drain and, where required, a neutraliser, piped so it cannot freeze or back up
  • The hydronic loop flushed, with a dirt or air separator and proper fill, expansion and relief components
  • Outdoor reset and controls set for your emitters, not left at factory defaults
  • Combustion tested and safety devices checked during commissioning
  • Manuals, warranty registration details and the written warranty terms left with you
  • A walkthrough of the pressure gauge, thermostat and shut-off locations

Who installs and services Super Hot and IBC boilers near me in Vancouver BC?

BC Wide Home Services Ltd is an independent TSBC-licensed contractor based in Burnaby and serving Metro Vancouver since 1999. Our licences are LGA0090068 and Class B gas licence CGA0028029, and all gas work is done by licensed gas fitters. We hold 4.7 stars from 181 Google reviews.

We install and service both Super Hot and IBC boilers as an independent contractor. We are not an authorised dealer, factory service centre or warranty centre for either brand, which means our recommendation is based on your house rather than on a supplier relationship. Alongside Super Hot and IBC, the gas boiler and combi brands we service include Navien, Rinnai and Bosch.

Every replacement starts with a free in-home estimate and ends with a written quote before any work begins. For repairs, diagnostic service calls are $189.00, and we go same-day where we can. Call (604) 473-9690 to book.

More questions homeowners ask

Is Super Hot or IBC better for a Vancouver home?

Neither is better for every home. Super Hot tends to suit owners who want simple, rugged equipment that is easy to service, while IBC suits homes that benefit from condensing operation and fine modulation, such as houses with in-floor radiant. A heat-loss calculation and a look at your emitters and venting will decide it.

Can I replace my old boiler with a Super Hot or IBC without changing my radiators?

Usually yes. Both brands can be connected to existing radiators or baseboard, but the water temperature those emitters need affects how efficiently a condensing boiler runs. We check the existing piping, flush the loop and set the controls to suit what you already have.

Do I need a permit to install a new boiler in Vancouver?

Yes. Installing a gas boiler requires a gas permit and the work must be done by a licensed gas fitter. The permit should be listed on your written quote, and the installation is open for inspection afterwards.

How much does a boiler diagnostic cost in Greater Vancouver with BC Wide?

Diagnostic service calls are $189.00. If the diagnosis leads you to replace the boiler or install a new one through BC Wide, the $189.00 is waived and taken off the installation. The in-home estimate for a replacement is free.

How long does it take to replace a boiler with a Super Hot or IBC unit?

It depends on venting changes, piping work, permit timing and equipment availability. A straightforward swap moves faster than a job that needs a new vent route or a chimney liner. We give you the expected timeline on the written quote, and for no-heat situations we work same-day where we can.

What warranty comes with a Super Hot or IBC boiler?

Warranty terms are set by each manufacturer and vary by product and by registration, so we do not quote a length here. Your written quote should state the manufacturer warranty terms and our own workmanship terms. Ask for both in writing before you sign.

4.7★181+ Google reviews
27+Years serving Greater Vancouver
20+Brands serviced
$0Free written estimates on installs

Frequently asked questions

How often should a boiler be serviced?
Annual servicing is recommended for all residential boilers. BC Wide's annual service includes combustion analysis, heat exchanger inspection, expansion tank pressure check, condensate trap cleaning, and a full safety check. Annual maintenance is also required to keep most manufacturer warranties valid.
How much does a new boiler cost in Vancouver?
A typical residential high-efficiency gas boiler in Metro Vancouver costs $7,500–$15,000 installed, depending on size, brand, and whether the system is heating only or a combi unit that also handles hot water. BC Wide provides a free written quote with three options at different price points.
How long does a boiler last?
A well-maintained cast-iron boiler can last 25–30 years, a modern high-efficiency condensing boiler typically lasts 15–20 years, and a combi boiler 12–18 years. Annual servicing has the single biggest impact on lifespan.
My boiler is making a banging or kettling noise. Is that dangerous?
Kettling (a banging or whistling sound) is usually caused by limescale build-up on the heat exchanger and is a sign the system is overheating in localised spots. It will not always cause immediate failure but it shortens the life of the boiler and should be addressed within a few weeks.
Do you service Viessmann, IBC, Baxi, Laars, and Weil-McLain boilers?
Yes. BC Wide is one of the few HVAC companies in the Lower Mainland with deep experience on European and high-end North American boilers including Viessmann, IBC, Baxi, Laars, Weil-McLain, NTI, Navien and Rinnai. We carry common parts in the truck.
Should I repair or replace my old boiler?
A useful rule: if the boiler is more than 15 years old and the repair cost is more than 50% of replacement, replacement is the better investment. BC Wide will give you both a repair quote and a replacement quote and let you decide.
What HVAC services does BC Wide offer in Metro Vancouver?
BC Wide installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses, condos with strata systems, and small commercial buildings.
How long has BC Wide been in business?
BC Wide Heating & Air Conditioning has been serving the Greater Vancouver area since 1999. Our TSBC-licensed technicians have built a reputation as some of the most experienced furnace, boiler and heat-pump specialists in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.

What Greater Vancouver homeowners say about BC Wide

Verified Google reviews — 4.7 average across 181+ ratings
★★★★★
"Alan and Mo were amazing today. They seamlessly replaced our furnace and tankless hot water tank in record time."
Mebz Esmail
Google review · Aug 2026
★★★★★
"Alan and his colleague are very friendly and professional. They installed everything and left it clean."
Laura E. Martínez Urrutia
Google review · Aug 2026
★★★★★
"I have been using BC Wide HVAC Services for over five years for my annual maintenance."
Thor Campbell
Google review · Aug 2026
★★★★★
"Excellent service from start to finish! B.C. Wide is knowledgeable, very professional and showed up on time! I highly recommend this company."
Mark Bouffard
Google review · Aug 2026
★★★★★
"I found these guys on Google. I just moved into a place where no maintenance has been done in the last 6 years."
Thomas Lee
Google review · Aug 2026
★★★★★
"Heat pump, furnace and tankless water heater installed. Competitive price. Careful, friendly, competent, efficient installation team. Professional appearing installation. Good company, highly recommended."
Thomas T
Google review · Jul 2026

Get a Free Quote — Right From This Page

Request a Free Quote

We'll call you back fast — usually within a few hours.
✓ Thanks! We've received your request and will call you back shortly.

Get Comfortable — Talk to BC Wide Today

Free, no-obligation quotes. TSBC-licensed local technicians serving Greater Vancouver since 1999.

Licensed & Insured: Technical Safety BC Licensed Gas Contractor LGA0090068  ·  Class B Gas Licence CGA0028029  ·  Red Seal Technicians  ·  Serving Greater Vancouver since 1999
🔥 Emergency Service(604) 473-9690
📞Call NowFast Response ✉️Email UsGet A Quote